Moulinex Cosmo User Manual

Download

www.moulinex.com

901866_not_cosmo.qxd:901866 27/05/08 16:56 Page a2

18a

18b

17b

17a

20*

23*

26*

* Selon modèles : il s'agit d'équipements spécifiques à certains modèles ou d'accessoires disponibles en option.

28*

24*

25*

27*

21*

901866_not_cosmo.qxd:901866 27/05/08 16:56 Page a3

CLICK

PUSH

PUSH PUSH

12H

24H

CLICK

2 3

14a

14b

14c

20a

20b

20c

13b

901866_not_cosmo.qxd:901866 27/05/08 16:56 Page a4

SAFETY RECOMMENDATIONS

For your safety, this appliance conforms to the applicable standards and regulations (Low Voltage, Electromagnetic Compatibility, Environmental, etc. Directives).

1. CONDITIONS OF USE

• Your vacuum cleaner is an electrical appliance: it must only be used under normal operating conditions.

• The appliance should be used and stored out of the reach of children. Never leave the appliance unattended when it is switched on.

• Always keep nozzles and tube ends well away from eyes and ears.

• Do not vacuum wet surfaces, any water or any kind of liquids, hot substances, ultra-fine substances (plaster, cement, ash, etc.) large sharp debris (glass), dangerous products (solvents, stripping compounds, etc.), chemical products (acids, cleaners, etc.), inflammable or explosive products (petrol- or alcohol-based).

• Do not immerse the appliance in water, project water on the appliance or store it outdoors.

• Do not use the appliance if it has been dropped and shows signs of damage or functions abnormally. In this case do not open the appliance and call our helpline (overleaf). In this case, do not open the appliance, but send it to the nearest Approved Service Centre or contact Moulinex Customer Service (see contact particulars on last page).

2. ELECTRICAL POWER SUPPLY

• Check that the power voltage for your vacuum cleaner corresponds to that of your mains installation. You will find this information underneath your appliance.

• Unplug the appliance by removing the plug from the wall socket:

- immediately after use,

- before changing accessories,

- before maintenance, cleaning or changing the dustbag.

• Do not use the appliance:

- if the power cord is damaged. To avoid danger, the whole reel and power cord unit of your vacuum cleaner must be replaced by a Moulinex Approved Service Centre.

3. REPAIRS

Repairs should only be carried out specialists using original replacement parts. It is dangerous to try to repair an appliance yourself.

DESCRIPTION

1. a - Horizontal parking

b - Upright parking

2. On/Off pedal

3. Electronic power regulator

4. Automatic cable rewind pedal

5. Air exit grill

6. Carrying handle

7. Lid

8. Suction opening

9. Dust collector compartment

10. Dust box fitted security device

11. Dust box

12. Dust box handle

13. Air outlet filter capsule (un)locking clip

14. Dust box opening area

15. HEPA filter capsule opening clips

16. Air inlet filter ref. MT0006 01

17. Air outlet filter capsule

a- Air outlet filter ref. MT0006 01 b- Capsule

18. HEPA filter capsule

a- Black foam filter b- HEPA filter ref. MT0006 01

901866_not_cosmo.qxd:901866 27/05/08 16:56 Page 7

*Depending on model: it means special equipment for some models or optional accessories.

Standard accessories:

19. Flexible tube with grip and mechanical power regulator

20. Telescopic tube*

21. Tubes*

22. Automatically adjusting floor head

23. Floor nozzle*

24. Furniture nozzle*

25. Slot attachment convertible into a brush*

26. Turbobrush*

27. Mini turbobrush*

28. HEPA filter scraper*

BEFORE USING FOR THE FIRST TIME

1. REMOVE PACKAGING

• Take your appliance out of its packaging. Keep your warranty card and carefully read the operating instructions before using your appliance for the first time.

2. HINTS AND PRECAUTIONS

• Before each use, the supply cord should be completely unwound.

• Do not allow it to become trapped or pulled over sharp edges.

• If you use an electric extension cord, make sure that it is in perfect condition and appropriate to the power rating of your appliance.

• Your vacuum cleaner is fitted with a device to protect against the motor overheating. In certain cases, (using the power nozzle on chairs, etc.) the device is triggered and the appliance may make an unusual noise. This is of no consequence.

• Never unplug the appliance by pulling on the cord.

• Do not move the vacuum cleaner by pulling on the cord, the appliance must be moved by its carrying handle.

• Never operate without the dust box and without a filtration system: air inlet filter (16), air inlet filter capsule (17), HEPA filter capsule (18).

• Only use filters by Moulinex.

• Use only original Moulinex accessories.

• Stop and disconnect your vacuum cleaner after each use.

• Always stop and unplug your appliance before maintenance or cleaning.

• Check the filtration system: air inlet filter (16), air inlet filter capsule (17) and HEPA filter capsule (18) is properly in position.

• In the event that you find it difficult to obtain accessories and filters for this vacuum cleaner, contact the Moulinex customer service (see contact information on the last page).

This appliance is not intended for use by people (including children) whose physical, sensory or mental capacities are disabled, or by people with no experience or familiarity with such devices, unless they are supervised by a person who is responsible for their security or have received instructions as to how to use the appliance. Children must be supervised to ensure that they do not play with the appliance.

901866_not_cosmo.qxd:901866 27/05/08 16:56 Page 8

*Depending on model: it means special equipment for some models or optional accessories.

USING THE APPLIANCE

1. ASSEMBLING THE ELEMENTS OF THE APPLIANCE

Note! Always stop and unplug your vacuum cleaner before changing accessories.

• Push the flexible hose (19) in the opening (8) until your hear a clicking sound - fig. 1.

• To remove it, press the clips on the tube (19) and pull - fig. 2.

• Assemble the telescopic tube* (20). Adjust it to the desired length - fig. 3.

• Fit the appropriate accessory to the end of the tube:

- For rugs and wall-to-wall carpeting: use the head (22) with brushes lifted - fig. 4a.

- For parquets and smooth flooring: use the nozzle (22) with the brush extended - fig. 4b. or use the parquet nozzle* (23).

- For corners and other areas that are difficult to reach, use the slot attachment convertible into a brush* (25) in the flat attachment position.

- For furniture, use the slot attachment convertible into a brush* (25) or the furniture nozzle (24).

2. PLUGGING IN THE ELECTRICAL POWER CORD AND USING THE VACUUM CLEANER

• Completely unwind the power cord, plug in your vacuum cleaner and push the on/off pedal (2) - fig. 5.

• Set the suction power:

- using the electronic power regulator (3): turn the switch on the electronic regulator to set the suction power: towards max position for floors and min position for furniture and fragile fabrics - fig. 6a.

- with the mechanical power regulator on the grip: Open the manual suction regulator to reduce the suction power manually – for fragile surfaces, for example - fig. 6b.

3. STORING AND TRANSPORTING THE APPLIANCE

• After use, stop your appliance by pressing on the on/off pedal (2) and unplug it - fig. 7. Replace the cable by pressing the automatic cable rewind pedal (4) - fig. 8.

• In the horizontal position, hook the floor nozzle (22) onto its storage position at the rear of the appliance (1a) - fig. 9a.

• Upright, place the attachment (22) in its housing under the appliance (1b) - fig. 9b.

• Carry your vacuum cleaner easily thanks to its carry handle (6).

CLEANING AND MAINTENANCE

Important! Always stop and unplug your vacuum cleaner before maintenance or cleaning.

1. EMPTY AND CLEAN THE DUST BOX

1.1. EMPTY THE DUST BOX

• Empty the dust box (11) after each use.

• Remove the flexible tube (19) from the suction opening (8) - fig. 2.

• Open the lid (7) of your vacuum cleaner.

• Remove the dust box (11) from its housing (9) - fig. 10.

• Press the box opening zone (14) to open it - fig. 11.

• Remove the lid - fig. 12, empty the box over a dustbin - fig. 13a.

• Make sure no dust is left in the box, then clean the edges of the box - fig. 13b.

• Close the dust box and replace it in its housing (9).

1.2. CLEAN THE DUST BOX

• You can also run the dust box under soapy water only after having previously removed the HEPA

filter capsule (18), or the black foam filter (18a) and the HEPA filter (18b).

• After having emptied the dust box out over a dustbin - fig. 13a, unclip the HEPA filter capsule (18), by

simultaneously pressing the opening clips (15) located on either end of the box - Figure 14a.

• Remove the HEPA filter capsule (18) - fig. 14b.

• Run the dust box under soapy water and leave it to dry for 12 hours - fig. 14c.

• Once the box is completely dry, replace the HEPA filter capsule (18): black foam filter (1880) and HEPA

filter (18b) under the box and replace the dust box (11) in its housing (9) - fig 15.

901866_not_cosmo.qxd:901866 27/05/08 16:56 Page 9

*Depending on model: it means special equipment for some models or optional accessories.

2. CLEAN THE HEPA FILTER CAPSULE (REF: MT0006 01)

Important! Clean the HEPA filter capsule (18): black foam filter (18a) and HEPA filter (18b) every month. Also be sure to change the entire filtration system on the appliance (ref. MT0006 01) every year: the air inlet filter (16), air inlet filter capsule (17) and the HEPA filter capsule (18).

• Remove the flexible tube (19) from the suction opening (8) - fig. 2.

• Open the lid (7) of your vacuum cleaner.

• Remove the dust box (11) from its housing (9) - fig. 10.

• Simultaneously press the HEPA filter capsule opening clips (15) - fig. 14a.

• Separate the black foam filter (18a) from the HEPA filter (18b) - fig. 14b.

2.1 CLEANING THE BLACK FOAM FILTER (18a)

• Wash the black foam filter under the tap, squeeze it out like a sponge and leave to dry for 24 hours - fig. 16.

• Once completely dry, assemble the cassette HEPA filter (18): black foam filter (18a) and HEPA filter (18b) under the dust box (11) and replace the box in its housing (9) - fig. 15.

Attention! The foam filter should only be put back into the appliance when it is completely dry.

2.2 CLEANING THE HEPA FILTER (18b)

Attention! Only use the scraper * (28) on the inner side of the filter, never on the outer face, as this may cause damage or tearing.

• Turn the HEPA filter (18b) over and tap the dust into a dustbin - fig. 17.

• then scrape the filter (inner face of the capsule) using the scraper * (28) under cold or warm water, then leave the HEPA filter to dry for 24 hours - fig. 18.

• Once completely dry, assemble the cassette HEPA filter (18): black foam filter (18a) and HEPA filter (18b) under the dust box (11) and replace the box in its housing (9) - fig. 15.

• Ensure that the HEPA filter is completely dry before you put it back in the appliance.

Attention! Make sure that all the filtration system is properly positioned before turning your appliance back on.

3. REPLACING THE FILTRATION SYSTEM (REF. MT0006 01)

• Remove the flexible tube (19) from the suction opening (8) - fig. 2.

• Open the lid (7) of your vacuum cleaner.

• Remove the dust box (11) from its housing (9) - fig. 10.

3.1. HEPA FILTER CAPSULE (18)

• Simultaneously press the HEPA filter capsule opening clips (15) - fig. 14a.

• Separate the black foam filter (18a) from the HEPA filter (18b) - fig. 14b.

• If the HEPA filter capsule (18) (black foam filter (18a) and HEPA filter (18b)) is damaged, discard it fig. 19 and replace it with a new HEPA filter capsule (ref. MT0006 01).

• Assemble the HEPA filter capsule (18): black foam filter (18a) and HEPA filter (18b) under the dust box (11) and replace the box in its housing (9) - fig. 15.

3.2. AIR INLET FILTER (16)

• Remove the air inlet filter (16) - fig. 20a.

• Discard it - fig. 20b.

• Replace it with a new air inlet filter (ref. MT0006 01) - fig. 20c.

3.3. AIR OUTLET FILTER (17a)

• Unclip the air outlet filter capsule (17) by lifting the locking clip (13) - fig. 21-22.

• Remove the air outlet filter (17a) and discard it - fig. 23.

• Replace a new air outlet filter (ref. MT0006 01) in the capsule (17b).

• Lock the air outlet filter capsule (17) in its housing by pressing the clip (13), until you hear a click fig. 24.

901866_not_cosmo.qxd:901866 27/05/08 16:56 Page 10

*Depending on model: it means special equipment for some models or optional accessories.

4. CLEAN THE VACUUM CLEANER

• Clean the housing of the vacuum cleaner with a soft and humid rag and let dry with a dry rag - fig. 25.

• Do not use detergents or any corrosive or abrasive products.

TROUBLESHOOTING

Important! As soon as your vacuum cleaner stops performing efficiently, and before making any checks, stop it by pressing on the On/Off pedal (2).

1. IF YOUR VACUUM CLEANER DOES NOT START

• The appliance is not plugged-in, check that the appliance is correctly plugged in.

2. IF THERE IS NO SUCTION

• An accessory or the tube is clogged. Unclog the accessory tube or flexible hose.

• The dust box has not clicked into place: check that it is properly positioned.

• The lid (7) of your vacuum cleaner is not closed properly.

3. IF THE SUCTION OF YOUR VACUUM CLEANER HAS DROPPED, IT MAKES A NOISE AND WHISTLES

• An accessory or the flexible hose is partially clogged. Unclog the accessory tube or flexible hose.

• The dust box is full: empty it (see 1. of the CLEANING AND MAINTENANCE chapter).

• The filtration system is saturated: clean it (see 2. of the CLEANING AND MAINTENANCE chapter). If the problem persists, change the filtration system (see 3. of the CLEANING AND MAINTENANCE chapter).

• The electronic power regulator (3) is set at minimum: increase the power using the electronic power regulator (unless you are cleaning fragile fabrics).

• If the mechanical power control of the power nozzle is open, close it.

• The lid (7) of your vacuum cleaner is not closed properly.

4. IF THE LID DOES NOT CLOSE

• Ensure that the dust box (11) is properly mounted and present.

• Ensure that the dust box (11) is well properly positioned in the dust tray housing (9).

5. IF THE FLOOR HEAD IS HARD TO MOVE AROUND

• Open the mechanical power regulator on the grip or decrease power.

• Ensure that the position (brush retracted / brush out) of the attachment (22) corresponds to the surface being cleaned.

6. IF THE POWER CABLE DOES NOT REWIND COMPLETELY

• The power cable is slow in re-entering its housing. Pull the cable back out and press on the automatic cable rewind pedal.

7. IF YOUR VACUUM CLEANER STOPS WHILE IN OPERATION

• The overheating protective device has been triggered. Check that the tube and the pipe are not blocked or that the bag or filter are not full. Leave to cool down for 30 minutes before using the vacuum cleaner again.

If you have any product problems or queries, please contact our customer Relations Team first for expert help and advice (see the contact details on the last page).

WARRANTY

• This product has been designed for domestic use only. Any professional use, innapropriate use or failure to comply with the instructions, the manufacturer accepts no responsibility and the guarantee will not apply.

• Read the instructions for use carefully before using your appliance for the first time: any use which does not conform to these instructions will absolve Moulinex from any liability.

901866_not_cosmo.qxd:901866 27/05/08 16:56 Page 11

*Depending on model: it means special equipment for some models or optional accessories.

ACCESSORIES* VACUUMING FITTING AN ACCESSORY PURCHASE LOCATIONS

Floor nozzle For fragile floors.

Fit the hardfloor tool to the end of the tube.