Motorola MC10H352FN, MC10H352L Datasheet
SEMICONDUCTOR TECHNICAL DATA
2–96
REV 5
Motorola, Inc. 1996
3/93
The MC10H352 is a quad translator for interfacing data between a
CMOS logic section and the PECL section of digital systems when only a
+5.0 Vdc power supply is available. The MC10H352 has CMOS
compatible inputs and PECL complementary open–emitter outputs that
allow use as an inverting/non–inverting translator or as a differential line
driver. When the common strobe input is at a low logic level, it forces all
true outputs to the PECL low logic state (≈ +3.2 V) and all inverting
outputs to the PECL high logic state (≈ +4.1 V).
The MC10H352 can also be used with the MC10H350 to transmit and
receive CMOS information differentially via balanced twisted pair lines.
• Single +5.0 V Power Supply
• All VCC Pins Isolated On Chip
• Differentially Drive Balanced Lines
• tpd = 1.3 nsec Typical
MAXIMUM RATINGS
Characteristic Symbol Rating Unit
Power Supply V
CC
0 to +7.0 Vdc
Input Voltage (VCC = 5.0 V) V
I
0 to V
CC
Vdc
Output Current— Continuous
— Surge
I
out
50
100
mA
Operating Temperature Range T
A
0 to +75 °C
Storage Temperature Range— Plastic
— Ceramic
T
stg
–55 to +150
–55 to +165
°C
ELECTRICAL CHARACTERISTICS (VCC = V
CC1
= V
CC2
= 5.0 V ± 5.0%)
0° 25° 75°
Characteristic Symbol Min Max Min Max Min Max Unit
Power Supply
ECL — 50 — 45 — 50 mA
pp y
Current
TTL — 20 — 15 — 20 mA
Reverse Current
Pins 7, 8, 12, 14
Pin 9
I
R
——25
100——2080——25100
µA
Forward Current
Pins 7, 8, 12, 14
Pin 9
I
F
——–0.8
–3.2——
–0.6
–2.4——
–0.8
–3.2
mA
Input Voltage
Breakdown
V
(BR)in
5.5 — 5.5 — 5.5 — Vdc
Input Clamp Voltage
(Iin = –18 mA)
V
I
— –1.5 — –1.5 — –1.5 Vdc
High Output
Voltage (1)
V
OH
3.98 4.16 4.02 4.19 4.08 4.27 Vdc
Low Output
Voltage (1)
V
OL
3.05 3.37 3.05 3.37 3.05 3.37 Vdc
High Input Voltage V
IH
3.15 — 3.15 — 3.15 — Vdc
Low Input Voltage V
IL
— 1.5 — 1.5 — 1.5 Vdc
(1) With VCC at 5.0 V. VOH/VOL change 1:1 with VCC.
*Positive Emitter Coupled Logic
LOGIC DIAGRAM
DIP
PIN ASSIGNMENT
B OUT
B OUT
N.C.
A OUT
A OUT
V
CC
B IN
A IN
ECL V
CC
C OUT
C OUT
D OUT
D OUT
VCC 2
C IN
N.C.
20
19
18
17
16
15
14
13
1
2
3
4
5
6
7
8
COMMON
STROBE
GND
D IN
CMOS V
CC
12
11
9
10
14 19
18
12
16
17
8
5
4
71
2
9
B IN
A IN
COMMON
STROBE
D IN
C IN
B OUT
B OUT
A OUT
A OUT
D OUT
D OUT
C OUT
C OUT
VCC (+5.0 VDC) = PINS 6, 11, 15, 20
GND = PIN 10
L SUFFIX
CERAMIC PACKAGE
CASE 732–03
P SUFFIX
PLASTIC PACKAGE
CASE 738–03
FN SUFFIX
PLCC
CASE 775–02
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
T ables on page 6–36 of the Motorola MECL Data
Book (DL122/D).
MC10H352
2–97 MOTOROLAMECL Data
DL122 — Rev 6
AC PARAMETERS
0° 25° 75°
Characteristic Symbol Min Max Min Max Min Max Unit
Propagation Delay (1) t
pd
0.4 1.9 0.4 2.0 0.4 2.1 ns
Rise Time (20% to 80%) t
r
0.4 1.9 0.4 2.0 0.4 2.1 ns
Fall Time (80% to 20%) t
f
0.4 1.9 0.4 2.0 0.4 2.1 ns
Maximum Operating Frequency f
max
150 — 150 — 150 — MHz
(1) Propagation delay is measured on this circuit from VCC/2 on the input waveform to the 50% point on the output waveform.
NOTE:
Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is maintained. Outputs are terminated through
a 50–ohm resistor to VCC – 2.0 Vdc.
Loading...