BEFORE YOU
BEGIN
Before using this product, read the Important Safety and
Legal Information pamphlet and follow its instructions.
1
H350
Bluetooth®
Handsfree Headset
Get Connected in
4 Quick Steps
1 - CHARGE YOUR
HEADSET
2 - PUT HEADSET
IN PAIR MODE
3 - PAIR PHONE
WITH HEADSET
4 - TEST AND USE
CHARGE YOUR
HEADSET
Take a moment before you get started to
familiarize yourself with your new
H350 Handsfree Headset.
Volume
Buttons
Call
Button
Earhook
Blue
Indicator
Light
Microphone
PUT YOUR HEADSET IN
2
PAIRING MODE
Charge your headset's battery for 2 hours:
Plug the Motorola charger into the end of
1
the headset.
The blue indicator light turns on when the
battery is charging. It may take up to 1
minute for the light to turn on. When the
headset's battery is fully charged (about 2
hours), the blue indicator light turns off.
Unplug the charger from the headset.
2
Note: Headset is not functional while charging.
Before you can use your headset, you must
pair (link) it with your phone.
Call Button
Blue Indicator Light
With the headset power off, press and hold
the Call button for 6 to 10 seconds until the
blue indicator light turns on and remains
steadily lit.
Note: The blue light will flash as you press and hold the Call
button. Continue holding down the Call button until the blue
light is steadily lit.
Note: If you let go of the Call button before the blue light is
on and steady, ensure that your headset is off before trying
again.
Note: To turn off headset, see "Turning Headset On/Off" on
the reverse side of this guide.
TROUBLESHOOTING
My phone does not find my headset.
Make sure the blue light on your headset is
steadily lit when your phone is searching for
devices (see step 2).
My headset worked before but now it's
not working.
Make sure your phone is on and the
Bluetooth feature is turned on in your phone
(see step 3). If the Bluetooth feature has
been turned off or was turned on only
temporarily, you may need to restart the
Bluetooth feature (see step 3). If you have
confirmed the Bluetooth feature is on in your
phone, pair your phone and headset again
(see step 3).
Support.
If you need more help, contact us at
1-877-MOTOBLU or visit us at
www.hellomoto.com/bluetooth and click
Support.
Motorola, Inc.
Consumer Advocacy Office
1307 East Algonquin Road
Schaumburg, IL 60196
www.hellomoto.com
1-877-MOTOBLU
1-888-390-6456 (TTY/TDD United States for
hearing impaired)
Guide Number: 6809501A24-A
MOTOROLA and the Stylized M Logo are registered in the US
Patent & Trademark Office. The use of wireless devices and their
accessories may be prohibited or restricted in certain areas.
Always obey the laws and regulations on the use of these
products. The Bluetooth trademarks are owned by their
proprietor and used by Motorola, Inc. under license. All other
product or service names are the property of their respective
owners.
TURN ON BLUETOOTH
3
ON YOUR PHONE AND
PAIR WITH HEADSET
Your phone's Bluetooth feature is off by
default. To use your headset, turn on the
Bluetooth feature in your phone.
To turn on Bluetooth:
Select (
1
Bluetooth Link > Setup.
2
Scroll to Power.
Press Change.
3
Select On.
4
Select Back.
5
M
Menu) > Settings > Connection >
© Motorola, Inc. 2006.
TURN ON BLUETOOTH
ON YOUR PHONE AND
PAIR WITH HEADSET
Continued
Select [Look for Devices].
7
Note: Do not select STOP--you will automatically be
taken to the next screen.
Select Motorola H350.
8
Select Ye s to bond.
9
10
Enter the passkey 0000 and select OK.
When your headset and phone are
successfully paired, the blue light on your
headset will change from steadily lit to
flashing.
Select Handsfree.
6
Note: This procedure is for most Motorola phones. For
other phones, see your phone's user's guide or visit
www.hellomoto.com/bluetoothsupport and click Set Up
My New Product.
4
TEST AND USE
USING YOUR H350
Your phone and headset are now paired and
ready to make and receive calls. To confirm they
are operating properly, make a call:
Place the headset over your ear. See "Wearing
1
the Headset" on the reverse side of this
guide.
On your phone, dial the number you want to
2
call and press the Send key.
If your phone and headset are successfully
3
paired, you will hear ringing on the headset.
After you have successfully paired your phone
and headset, you do not need to repeat these
initial setup steps each time you use the
headset.
See Features and Functions Guide
on the reverse side
of this guide
for information on
using your H350.
Features and
Functions Guide
H350
Bluetooth®
Handsfree Headset
IMPORTANT:
Be sure to first follow the
Quick Start Guide
on the reverse side
TURNING HEADSET
ON/OFF
To turn your headset on, press and hold the
Call button until the indicator light flashes.
Then, release the button.
Note: Headset may take up to 4 to 5 seconds to turn on.
To turn your headset off, press and hold
the Call button until the indicator light flashes
rapidly and then turns off.
Call
Button
of this guide
to complete initial setup
of your H350.
WEARING THE
CHANGING FOR USE
HEADSET
Open the earhook.
1
Loop the earhook over your ear.
2
3
Press the headset to your ear.
3
4
ON OTHER EAR
You can wear your H350 headset on your left or
right ear. The headset comes ready for the right
ear. To change the headset for the left ear:
Open the earhook 90
1
degrees from the
headset.
Gently lift and pull the
2
top of the earhook up
and off the upper
hinge pin. Then, pull it
away to remove it.
Flip the headset over.
3
Hook the bottom of
4
the earhook onto the
lower hinge pin, then
lift and pull the top of
the earhook over the
upper hinge pin.
1 Open Earhook
2 Pull Earhook Up
Hinge Pin
CHANGING VOLUME BUTTON
ORIENTATION
If you change your headset to wear on the
other ear, you can also change the
orientation of the volume buttons.
Turn the headset power off.
1
Press the Call button along with the
2
Volume button you want to assign as
"volume up" button until the indicator
light flashes twice.
The headset power turns on.
Call
Button
Volume
Buttons
MAKING CALLS
MAKING CALLS
CONTINUED
Function Action
Make a voice dial call Tap the Call button
and speak the
name after the tone
End a call Tap the Call button
Receive a call Tap the Call button
Reject a call Press and hold the
Call button until you
hear a beep
Redial last call Press and hold the
Call button until you
hear a beep
Answer a second Press and hold the
incoming call Call button (places
first call on hold)
Note: Your H350 supports both Handsfree and Headset
Profiles. Accessing call functions depends upon which
profile your phone supports. See your phone's user's guide
for more information.
Function Action
Toggle between two Press and hold
active calls the Call button
Join a 3-way call Press and hold
both Volume buttons
Put an active call on Press and hold the
hold or resume a call Call button until you
on hold hear a beep
Transfer a call from the Tap the Call button
phone to the headset
Disable or enable the Press and hold
indicator light both Volume
buttons for 3 to 4
seconds
Mute or unmute a call Tap both Volume
buttons
Note: Some features are phone/network dependent.
INDICATOR LIGHTS
The indicator light provides information about
your headset status.
With the Charger Plugged In
Headset Indicator Headset Status
On (steady) Charging
Off Charging complete
With No Charger Plugged In
Headset Indicator Headset Status
Off Power off
On (steady) Pairing mode
10 rapid flashes Pairing successful
Slow pulse Connected
(on a call)
Quick flash Standby
(not on call)
AUDIO TONES
The audio tones provide information about your
headset status.
Audio Tone Headset Status
Single high tone when Volume at minimum
pressing volume button or maximum
Five rapid high tones Low battery
repeated every 60 sec.
No audio indications; Out of range
deteriorating quality
Ring tone Incoming call
Single high tone Pairing confirmation
Single low tone Voice activation
Dual high/low tone Voice tag not
recognized
Single high tone End call
Low to high tone Phone network
not available
Note: After 5 minutes of inactivity, the light stops flashing to
conserve power, but the headset remains in standby mode.
Two ascending tones Mute enabled
Two descending tones Mute disabled
Loading...