Motorola BSR 64000 Reference Manual

Page 1
BSR 64000 Command
Reference Guide
Page 2
Notice
Copyright © 2002 Motorola, Inc. All rights reserved
Motorola reserves the right to revise this publication and to make changes in content from time to time without obligation on the part of Motorola to provide notification of such revision or change. Motorola provides this guide without warranty of any kind, either implied or expressed, including, but not limited to, the implied warranties of mechantability and fitness for a particular purpose. Motorola may make improvements or changes in the product(s) described in this manual at any time.
Motorola,the stylized M logo, and Intelligence Everywhere are registered tradmarks of Motorola, Inc. Broadband Services Router, BSR, BSR 64000, RiverDelta , SmartFlow are trademarks of RiverDel ta Networks, Inc. All other trademarks and registered tr ademarks are the property of their respecti ve owners.
501898-001-00 TPD-0035-01 Rev A
Published: October, 2002
Page 3
Preface
Scope iii Audience iii Documentation Set iii Conventions iv Notes, Cautions, Warnings v Contacting Support vi
1 System Administration Commands
Introduction 1-1 System Administration Command Descriptions 1-2
alias 1-3 banner motd 1-4 boot system 1-5 broadcast 1-6 clear log 1-7 clock set 1-8 clock timezone 1-9 configure 1-10 console authentication radius 1-11 copy 1-12 disable 1-14 download runtime nvram: 1-15 download slot 1-16 enable 1-18 enable authentication radius 1-19 enable password 1-20 enable secret 1-21 exit 1-22
Contents
Page 4
BSR 64000 Command Reference Guide
forced-download 1-23 help 1-24 history size 1-25 hostname 1-26 ip ftp password 1-27 ip ftp username 1-28 ip netmask-format 1-29 ldap client 1-30 ldap server primary 1-31 ldap search-base 1-32 ldap server 1-33 logging 1-34 logging buffered 1-35 logging console 1-37 logging facility 1-38 logging on 1-39 logging rate-limit 1-40 logging reporting 1-41 logging reporting default 1-43 logging session 1-44 logging trap 1-45 login 1-46 logout 1-47 more 1-48 page 1-49 password 1-50 radius-server 1-51 reload 1-53 reset 1-54 service password-encryptio n 1-55 session-timeout 1-56 show aliases 1-57 show boot 1-59 show srm alias 1-60
iv
Page 5
show chassis alias 1-61 show srm assetid 1-62 show chassis assetid 1-63 show srm serial-num 1-64 show chassis serial-num 1-65 show chassis status 1-66 show clock 1-68 show history 1-69 show log 1-70 show memory 1-71 show process 1-73 show process cpu 1-74 show process msg-q-info 1-75 show process semaphores 1-76 show process stack 1-77 show running-confi g 1-78 show startup-config 1-79 show users 1-80 show version 1-81 update slot 1-82 username 1-83 username privilege 1-84 username user-group 1-85 telnet authentication radius 1-86
Contents
2 IP Commands
Introduction 2-1 IP Command Descriptions 2-2
arp 2-3 arp (global) 2-4 arp timeout 2-5 cable helper-address 2-6 clear arp-cache 2-7 clear counters 2-8
v
Page 6
BSR 64000 Command Reference Guide
clear host 2-9 clear ip route 2-10 clear ip traffic 2-11 host authorization on 2-12 host authorization cpe 2-13 interface 2-14 ip access-group 2-16 ip address 2-17 ip broadcast-address 2-19 ip dhcp relay information 2-20 ip directed-broadcast 2-22 ip domain-list 2-23 ip domain-lookup 2-24 ip domain-name 2-25 ip forward-protocol udp 2-26 ip helper-address 2-27 ip host 2-28 ip irdp 2-29 ip mask-reply 2-31 ip mtu 2-32 ip name-server 2-33 ip proxy-arp 2-34 ip rarp-server 2-35 ip redirects 2-36 ip route 2-37 ip routing 2-38 ip unreachables 2-39 passive-interface 2-40 ping 2-41 show controllers 2-43 show host authorization 2-45 show host authorization cpe 2-46 show host unauthorized cpe 2-47 show hosts 2-48
vi
Page 7
show interfaces 2-49 show ip arp 2-50 show ip dhcp stat s 2-51 show ip interface 2-52 show ip irdp 2-53 show ip protocols 2-54 show ip route 2-55 show ip traffic 2-57 show sntp 2-58 show tcp brief 2-59 show tcp statistics 2-60 shutdown 2-63 sntp authenticate 2-64 sntp authentication-key 2-65 sntp broadcastdelay 2-66 sntp broadcast client 2-67 sntp disable 2-68 sntp server 2-69 sntp tru s te d-key 2-70 traceroute 2-71 tunnel checksum 2-72 tunnel destination 2-73 tunnel key 2-74 tunnel mode 2-75 tunnel source 2-76
Contents
3SNMP Commands
Introduction 3-1 SNMP Command Descriptions 3-2
show snmp 3-3 show snmp access 3-5 show snmp community 3-6 show snmp contact 3-7 show snmp context 3-8
vii
Page 8
BSR 64000 Command Reference Guide
show snmp engineID 3-9 show snmp group 3-10 show snmp host 3-11 show snmp location 3-12 show snmp packetsize 3-13 show snmp port number 3- 14 show snmp sysname 3-15 show snmp users 3-16 show snmp view 3-17 snmp-server access 3-18 snmp-server chassis-id 3-20 snmp-server community 3-21 snmp-server contact 3-22 snmp-server context 3-23 snmp-server enable traps 3-24 snmp-server engineID 3-26 snmp-server group 3-27 snmp-server host 3-28 snmp-server enable informs 3-30 snmp-server location 3-31 snmp-server packetsize 3-32 snmp-server port number 3-33 snmp-server shutdown 3-34 snmp-server sysname 3-35 snmp-server trap rate-limit 3-36 snmp-server user 3-37 snmp-server view 3-39
4 Debug Commands
Introduction 4-1 Debug Command Descriptions 4-2
debug arp 4-3 debug cable err 4-4 debug cable keyman 4-5
viii
Page 9
debug cable mac 4-6 debug cable map 4-7 debug cable modem-select 4-8 debug cable privacy 4-9 debug cable qos 4-10 debug cable range 4-11 debug cable reg 4-12 debug cable ucc 4-13 debug ip bg p 4-14 debug ip dv mrp 4-16 debug ip icmp 4-17 debug ip igmp 4-18 debug ip mfm 4-19 debug ip mrtm 4-20 debug ip ospf 4-21 debug ip packet 4-23 debug ip policy 4-24 debug ppp fsm 4-25 debug ppp packet 4-26 debug ip r edistribute 4-27 debug ip rip 4-29 debug ip rip database 4-30 debug ip r i p events 4-31 debug ip rip trigger 4-32 debug ip tcp transactions 4-33 debug ip ud p 4-34 debug radius 4-35 debug ip vrrp 4-36 debug snmp 4-37 debug sntp 4-38 debug specmgr 4-39 debug tunnel 4-40 show debugging 4-41 undebug all 4-42
Contents
ix
Page 10
BSR 64000 Command Reference Guide
5 Access List Commands
Introduction 5-1 Access List Command Descriptions 5-2
access-list (standard) 5-3 access-list (extended) 5-4 ip access-group 5-10 ip access-list 5-11 show access-lists 5-12 show ip access-lists 5-13
6 Routing Policy Commands
Introduction 6-1 Routing Policy Command Descriptions 6 -2
default-information originate 6-3 default-metric 6-5 ip policy route-map 6-6 match ip address 6-7 match ip next-hop 6-8 match ip route-source 6- 9 match metric 6-10 match route-type external 6-11 match route-type internal 6-12 route-map 6-13 set metric 6-15 set metric-type 6-16 show ip redistribute 6-17 show route-map 6-19
7RIPCommands
Introduction 7-1 RIP Command Descriptions 7-2
auto-summary 7-3 default-information originate 7-4 default-metric 7-5
x
Page 11
distance 7-6 distribute-list in 7-7 distribute-list out 7-8 ip rip authentication key 7-9 iip rip receive version 7-10 ip rip send version 7-11 ip split-horizon 7-12 network 7-13 offset-list 7-14 output-delay 7-16 passive-interface 7-17 redistribute 7-18 router rip 7-20 show ip rip database 7-21 timers basic 7-22 version 7-25
Contents
8 OSPF Commands
Introduction 8-1 OSPF Command Descriptions 8-2
area authentication 8-3 area default-cost 8-4 area nssa 8-5 area range 8-6 area stub 8-8 area virtual-link 8-10 auto-cost reference-bandwidth 8-12 auto-virtual-link 8-13 default-information originate 8-14 default-metric 8-16 distance ospf 8-17 distribute-list 8-19 ip ospf authentication-key 8-20 ip ospf cost 8-21
xi
Page 12
BSR 64000 Command Reference Guide
ip ospf database-filter all out 8-22 ip ospf dead-interval 8-23 ip ospf hello-interval 8-24 ip ospf message-digest-key 8-25 ip ospf priority 8-26 ip ospf retransmit-interval 8-27 ip ospf transmit-delay 8-28 network a rea 8-29 rfc1583-compatible 8-30 router os pf 8-31 show ip ospf 8-32 show ip ospf border-routers 8-33 show ip ospf database 8-34 show ip ospf interface 8-36 show ip ospf memory 8-37 show ip ospf neighbor 8-38 show ip ospf network 8-39 show ip ospf virtual-links 8-40 summary-address 8-41 timers spf 8-42
9 IGMP Commands
Introduction 9-1 IGMP Command Descriptions 9-2
clear ip igmp counters 9-3 ip igmp access-group 9-4 ip igmp query-interval 9-5 ip igmp query-max-response-time 9-6 ip igmp querier-timeout 9-7 ip igmp static-group 9-8 ip igmp version 9-9 ip igmp version1-querier 9-10 show ip igmp interface 9-11 show ip igmp groups 9-12
xii
Page 13
show ip igmp statistics 9-13
10 VRRP Commands
Introduction 10-1 VRRP Command Descriptions 10-2
clear ip vrrp 10-3 ip vrrp 10-4 ip vrrp (virtual router ID) 10-5 ip vrrp address 10-6 ip vrrp authentication key 10-7 ip vrrp authentication type 10-8 ip vrrp enable 10-9 ip vrrp preempt 10-10 ip vrrp priority 10-11 ip vrrp primary-ip 10-12 ip vrrp timer 10-13 ip vrrp verify-availability 10-14 show ip vrrp 10-15
Contents
11 IP Multicast Commands
Introduction 11-1 MRTM Command Descriptions 11-2
ip mroute 11-3 ip mroute static distance 11-4 ip mroute unicast distance 11-5 ip multicast-routing 11-6 show ip rpf 11-7
MFM Command Descriptions 11-8
clear ip multicast fwd-cache 11-9 clear ip multicast proto-cache 11-10 mtrace 11-11 show ip multicast cache-summary 11-12 show ip multicast fwd-cache 11-13 show ip multicast interface 11-14
xiii
Page 14
BSR 64000 Command Reference Guide
show ip multicast oi-fwd-cache 11-15 show ip multicast no-oi-fwd-cache 11-16 show ip multicast proto-cache 11-17
12 DVMRP Commands
Introduction 12-1 DVMRP Command Descriptions 1 2-2
ip dvmrp accept-filter 12-3 ip dvmrp default-information originate 12-4 ip dvmrp metric-o ffset 12-5 ip dvmrp output-report-delay 12-6 ip dvmrp out-report-filter 12-7 ip dvmrp probe-interval 12-8 ip dvmrp reject-non-pruner s 12-9 ip dvmrp summary-address 12-10 network 12-11 router dvmrp 12-12 show ip dvmrp information 12-13 show ip dvmrp interface 12-14 show ip dvmrp neighbor 12-15 show ip dvmrp network 12-16 show ip dvmrp route 12-17 show ip dvmrp route hold-down 12-18 show ip dvmrp summary-route 12-19 show ip dvmrp tunnels 12-20
13 CMTS Commands
Introduction 13-1 CMTS Command Descriptions 13-2
arp timeout 13-3 band 13-4 cable bundle 13-5 cable bundle master 13-6 cable downstream annex 13-7
xiv
Page 15
cable downstream carrier-only 13-9 cable downstream frequency 13-10 cable downstream interleave-depth 13-11 cable downstream modulation 13-13 cable downstream power-level 13-14 cable downstream reserve-bandwidth 13-15 cable downstream unreserve-bandwi dth 13-16 cable downstream shutdown 13-17 cable flap-list aging 13-18 cable flap-list insertion-time 13-19 cable flap-list miss-threshold 13-20 cable flap-list power-adjust threshold 13-21 cable flap-list size 13-22 cable helper-address 13-23 cable insert-interval 13-24 cable spectrum-group 13-25 clear cable flap-list 13-26 cable sync-interval 13-27 show bindings 13-28 show cable flap-list 13-29 show interface cable sid 13-31 cable insert-interval 13-32 cable modem deny 13-33 cable modem qos dsa 13-34 cable modem qos dsc 13-36 cable modem qos dsc service-flow 13-37 cable modem qos dsd 13-38 cable modem max-hosts 13-39 cable modem-aging-timer 13-40 cable modulation-profile 13-41 cable privacy cm-auth grace-time 13-43 cable privacy auth life-time 13-44 cable privacy cm-auth life-time 13-45 cable privacy cm-auth reset 13-46
Contents
xv
Page 16
BSR 64000 Command Reference Guide
cable privacy cm-tek grace-time 13-47 cable privacy cm-tek life-time 13-48 cable privacy cm-tek reset 13-49 cable privacy mcast access 13-50 cable privacy mcast del 13-51 cable privacy mcast new 13-52 cable privacy provision-cert -add 13-53 cable privacy tek life-time 13-54 cable shared-secret 13-55 cable sync-interval 13-56 cable ucd-interval 13-57 cable upstream channel-width 13-58 cable upstream data-backof f 13-59 cable upstream force-frag 13-60 cable upstream frequency 13-61 cable upstream invited-range- int erval 13-63 cable upstream map-interval 13-64 cable upstream max-calls 13-65 cable upstream minislot-si ze 13-66 cable upstream modulation-profile 13-67 cable upstream physical-delay 13-68 cable upstream power-level 13-70 cable upstream power-leve l defau lt 13-72 cable upstream pre-equalization 13-74 cable upstream range-backof f 13-75 cable upstream range-power-override 13-76 cable upstream rate-limit 13-77 cable upstream spectrum-group 13-78 cable upstream shutdown 13-79 cable upstream channel-width 13-80 clear cable flap-list 13-81 clear cable modem reset 13-82 clear counters cable 13-83 collect interval 13-84
xvi
Page 17
collect spectrum-data cable upstream 13-85 collect resolution 13-86 dhcpLeaseQuery authorization on 13-87 guard-band 13-88 hop action band 13-89 hop action channel-width 13-90 hop action frequency 13-91 hop action modulation-profile 13-92 hop action power-level 13-93 hop action roll-back 13-94 hop period 13-95 hop threshold flap 13-96 interface cable 13-97 ip dhcp relay information option 13-98 ping docsis 13-99 show host authorization 13-100 show cable device address-auth 13-101 show cable downstream 13-102 show cable flap-list 13-103 show cable insert-interval 13-104 show cable modem 13-105 show cable modem cpe 13-107 show cable modem detail 13-109 show cable modem hosts 13-110 show cable modem mac 13-111 show cable modem maintenance 13-113 show cable modem offline 13-115 show cable modem phy 13-117 show cable modem registered 13-118 show cable modem stats 13-121 show cable modem summary 13-124 show cable modem summary total 13-126 show cable modem svc-flow-id 13-128 show cable modem time-registered 13-129
Contents
xvii
Page 18
BSR 64000 Command Reference Guide
show cable modem unregistered 13-132 show cable modulation-profile 13-135 show cable privacy auth 13-137 show cable privacy cm-auth 13-138 show cable privacy cmts 13-139 show cable qos svc-flow classifier 13-140 show cable qos svc-flow dynamic-stat 13-142 show cable qos svc-flow log 13-143 show cable qos svc-flow phs 13-144 show cable qos svc-flow statistics 13-145 show cable qos svc-flow summary 13-146 show cable qos svc-flow upstream-stat 13-147 show cable spectrum-group 13-148 show cable sync-interval 13-149 show cable ucd-interval 13-150 show cable privacy auth 13-151 show cable privacy tek 13-152 show cable upstream 13-153 show interface cable 13-155 show interfaces cable downstream 13-158 show interfaces cable upstream 13-160 show interfaces cable upstream spectrum 13-162 show stats cmts 13-163 time band 13-165 time delete 13-166
14 QoS Commands
Introduction 14-1 QoS Command Descriptions 14-2
qos-list queue 14-3 ip qos-group 14-5 qos bw default 14-6 qos queue bw 14-7 show qos queue config 14-8
xviii
Page 19
show qos-lists 14-9
15 POS Commands
Introduction 15-1 POS Command Descriptions 15-2
crc 15-3 interface pos 15-4 ip address 15-5 network-clock-select 15-6 network-clock-select revertive 15-8 pos ais-shut 15-9 pos flag 15-10 pos framing 15-12 pos internal-clock 15-13 pos report 15 -14 pos scramble 15-16 pos signal mode 15-17 pos threshold 15-18 ppp magic-number 15-20 ppp mtu 15-21 ppp negot iation-count 15-22 ppp timeout 15-23 show controllers pos 15-24 show interfaces pos 15-26 show network-clocks 15-29 show ppp info 15-30
Contents
16 BGP Commands
Introduction 16-1 BGP Command Descriptions 16-2
aggregate-address 16-3 auto-summary 16-5 bgp always-compare-med 16-6 bgp client-to-client reflection 16-7
xix
Page 20
BSR 64000 Command Reference Guide
bgp cluster-id 16-8 bgp confederation as-confed-sequence 16-9 bgp confederation identifier 16-10 bgp confederation peers 16-11 bgp dampening 16-12 bgp default local-preference 16-14 clear ip bgp 16-15 clear ip bgp dampening 16-16 clear ip bgp flap-statistics 16-17 distance bgp 16-18 ip as-path access-list 16-20 ip community-list 16-21 match as-path 16-23 match community 16-24 neighbor advertisement-interval 16-25 neighbor default-originate 16-26 neighbor description 16-27 neighbor distribute-list 16-28 neighbor ebgp-multihop 16-29 neighbor filter-list 16-30 neighbor maximum-prefix 16-32 neighbor next-hop-self 16-34 neighbor password 16-35 neighbor peer-group (assigning members) 16-36 neighbor peer-group (creating) 16-37 neighbor remote-as 16-38 neighbor remove-private-as 16-39 neighbor route-map 16-40 neighbor route-reflector-client 16-41 neighbor send-community 16-42 neighbor shutdown 16-43 neighbor soft-reconfiguration inbound 16-44 neighbor timers 16-45 neighbor update-source loopback 16-46
xx
Page 21
neighbor weight 16-47 network 16-48 router bgp 16-49 route-map 16-50 set as-path prepend 16-52 set comm-list 16-53 set community 16-55 set local-preference 16-57 set metric-type 16-58 set origin 16-59 set tag 16-60 set ip next-hop 16-61 set weight 16-62 show ip bgp 16-63 show ip bgp cidr-only 16-64 show ip bgp community 16-65 show ip bgp community-list 16-67 show ip bgp dampened-paths 16-68 show ip bgp flap-statistics 16-69 show ip bgp memory 16-71 show ip bgp neighbors 16-72 show ip bgp paths 16-73 show ip bgp peer-group 16-74 show ip bgp regexp 16-75 show ip bgp summary 16-76 show ip as-path-access-list 16-77 show ip community-list 16-78
Contents
17 PIM Commands
Introduction 17-1 PIM Command Descriptions 17-2
ip pim border 17-3 ip pim bsr-candidate 17-4 ip pim bsr-candidate ip-address 17-5
xxi
Page 22
BSR 64000 Command Reference Guide
ip pim dr-priority 17-6 ip pim message-interval 17-7 ip pim query-interval 17-8 ip pim rp-candidate 17-9 ip pim rp-candidate group-list 17-10 ip pim rp-candidate interval 17-11 ip pim rp-candidate ip-address 17-12 ip pim rp-candidate priority 17-13 ip pim spt-threshold lasthop 17-14 ip pim spt-threshold rp 17-15 pim register-checksum 17-16 pim unicast-route-lookup 17-17 router pim 17-18
18 IS-IS Commands
Introduction 18-1 IS-IS Command Descrip tio ns 18-2
area-password 18-3 default-information originate 18-4 distance 18-5 domain-password 18-6 ip router isis 18-7 ip router isis passive 18-8 isis circuit-type 18-9 isis csnp-interval 18-10 isis hello-interval 18-11 isis hello-multiplier 18-12 isis metric 18-13 isis password 18-14 isis priority 18-15 isis lsp-interval 18-17 isis retransmit-interval 18-18 isis retransmit-throttle-interval 18-19 is-type 18-20
xxii
Page 23
Index
Contents
net 18-21 redistribute 18-23 router isis 18-24 set-overload-bit 18-25 show clns es-neighbors 18-26 show clns interface 18-28 show clns is-neighbors 18-30 show clns neighbors 18-32 show clns protocol 18-34 show clns traffic 18-36 show isis database 18-39 show isis spf-log 18-41 summary-address 18-44
xxiii
Page 24
Page 25
Scope
This document describes how to install a nd configure the Mot orola™ Broadband Services Router™ 64000 (BSR 64000™).
Audience
This document is for use by those persons who will install and configure the BSR 64000™ product. Only trained service personnel should install, maintain, or replace the BSR 64000.
Documentation Set
Preface
The following documents comprise the BSR 64000 documentation set:
BSR 64000 Command Reference Guide
This document contains the Command Line Interface (CLI) commands for managing, configuring, and maintaining the BSR 64000.
BSR 64000 Configuration and Management Guide
This document provides the instructions and procedures for configuring and managing the BSR 64000.
BSR 64000 Installation Guide
This document describes how to install the BSR 64000 product.
iii
Page 26
BSR 64000 Command Reference Guide
BSR 64000 Release Notes
These documents provide info rmati on ab out f eat ures not descri bed or incorrectly documented in the main documentation set; known problems and anomalies; product limitations; and problem resolutions.
BSR 64000 SNMP MIB Reference Guide
This document describes the Simple Network Management Protocol (SNMP) MIBs; provides informat ion that de scribes standar d and proprieta ry MIB support ; describes how to walk the MIBs and how to compile and l oad the SNMP MIB s. It also provides task examples.
BSR Troubleshooting Guide
This document provides i nst r ucti ons and procedures for tr ou ble s hoot ing the BSR product.
BSR 64000 Quick Start Guide
This document provides basic tasks used to get the BSR 64000 out of the box, running, connected to the network, and operational.
Conventions
This document uses the conventions in the following table:
Convention Example Explanation
angle brackets < > ping <ip-address>
ping 54.89.145.71
bar brackets [ ] disable [level] Bar brackets enclose optional arguments. The
Arguments in italic and enclosed by angle brackets must be replaced by the text the argument represents. In the example,
54.89.345.71 replaces <ip-address>. When entering the argument, do not type the angle brackets.
example indicates you can use the disable command with or without specifying a level. Some commands accept more than one optional argument. When entering the argument, do not type the bar brackets.
iv
Page 27
Preface
Convention Example Explanation
bold text cable relay-agent-option Boldface text must be typed exactly as it
appears.
brace brackets {} page {on | off} Brace brackets enclose required text. The
example indicates you must enter either on or off after page. The system accepts the command with only one of the para me ters . When entering the text, do not type the brace brackets.
italic text boot system <filename> Italic type indicates variables for which you
supply values in co mman d synt ax descri ptions . It also indicates file names, directory names, document titles, or emphasized text.
screen display Wed May 6 17:01:03
This font indicates system output.
2000
vertical bar | page {on | off} A vertical bar separates the choices when a
parameter is required. The example indicates you can enter either command:
page on or page off When entering the parameter, do not type the
vertical bar or the brace brackets.
Notes, Cautions, Warnings
The following icons and associated text may appear in this document.
Note: A note contains tips, suggestions, and other helpful informati on, such as references to material not contained in the document, that can help you complete a task or understand the subject matter.
Caution: The exclamation point, within an equilateral triangl e, is intended to alert the user to the presence of impo rtant installation, servicing, and operating inst ructions in the documents accompanying the equipment.
v
Page 28
BSR 64000 Command Reference Guide
Warning: This symbol indicates that dagerous voltages levels are present within the equipment. These voltages are not insulated and may be of sufficient strength to cause serious bodily injury when touc hed. The symbol may also appear on sche matics.
Contacting Support
Use the following information to contact Support:
U.S. 1-888-944-HELP
1-888-944-4357 International +.215-323-0044 WWW http://www.gi.com/BUSAREA/CUSACC/websupport.html Email cmtssupport@motorola.com
vi
Page 29
1
System
Administration Commands
Page 30
Page 31
Introduction
This chapter describes the following types of commands for the BSR 64000™: User management commands which establish authentication and to protect the
network from unauthorized users. Configuration file commands that handle the operating system and the system
software for the BSR. The configuration file commands allow you to customize the operating system configuration at system startup, and to modify and store the configuration file for later use.
System services commands that globally configure IP system services used with the BSR, such as protocols, NVRAM, IP parameters, the operating system, and the system clock
Lightweight Directory Access Protocol (LDAP) commands that are used with the BSR to access online directory services over the TCP/IP network protocol. The BSR becomes an LDAP client and connects to an LDAP server to requests services and/or information.
System Administration Commands
Logger commands which provide a way to configure system event reporting intended for diagnostics. The information in the report contains actions such as system startup, status, and event classes.
1-1
Page 32
BSR 64000 Command Reference Guide
System Administration Command Descriptions
This section conta ins an al phabetiz ed list a nd descri ptions of the system adminstration commands supported by the BSR.
1-2
Page 33
alias
The alias command allows you to specify an alias for a CLI command in a specific command mode (User EXEC, Privileged EXEC, or Global Configuration). The no alias command deletes a specific alias defined within the command mode.
Group Access
All
Command Mode
Global Configuration
Command Line Usage
alias {exec | priv | conf} <WORD> <WORD> no alias {exec | priv | conf} <WORD>
System Administration Commands
Command Syntax
exec User EXEC mode alias command priv Privileged EXEC mode alias
conf Global Configuration mode alias
WORD name of alias WORD the command that is aliase d
command
command
1-3
Page 34
BSR 64000 Command Reference Guide
banner motd
The banner motd command allows you to create a message-of the-day (motd) that displays upon successful login. The no banner motd command deletes the message of the day.
Group Access
All
Command Mode
Global Configuration
Command Line Usage
banner motd <1-10> <WORD> no banner motd
Command Syntax
1-10 message line number WORD text of the message.
1-4
Page 35
boot system
The boot system command lets you boot the BSR using a boot image file stored in either flash memory, NVRAM on the S uperviso ry Rout ing Modul e ( SRM), or an FTP or TFTP server.
Group Access
System Administrator
Command Mode
Privileged EXEC
Command Line Usage
boot system {flash: | ftp: | nvram:| tftp}{<filename>}
Command Syntax
System Administration Commands
flash: specifies flash memory as the location of the
boot image file
ftp: specifies a File Transport Protocol (FTP)
server as the location of the boot image file
nvram: specifies Non-volatile Random Access
Memory (NVRAM) as the location of the boot image file
tftp: spe c ifies a Trivial File Tr ans port Protocol
(TFTP) server as the location of the boot image file
filename filename of the boot image stored in flash,
NVRAM, or an FTP or TFTP server
1-5
Page 36
BSR 64000 Command Reference Guide
broadcast
The broadcast command is used to send a message to all connected users.
Group Access
System Administrator
Command Mode
Privileged EXEC
Command Line Usage
broadcast <WORD>
Command Syntax
WORD The text message intended for broadcast.
1-6
Page 37
clear log
The clear log command deletes buffered log data.
Group Access
All
Command Mode
All modes except User EXEC
Command Line Usage
clear log
System Administration Commands
1-7
Page 38
BSR 64000 Command Reference Guide
clock set
The clock set command sets the system clock.
Group Access
System Administrator
Command Mode
Privileged EXEC
Command Line Usage
clock set <hh:mm:ss> {<1-31> <MONTH> | <MONTH> <1-31>} <1993-2035>
Command Syntax
hh:mm:ss current time in 24-hour format 1-31 numeric notation for the current day MONTH three letter abbreviated name of the current
month
1993-2035 numeric notation for the curent year
1-8
Page 39
clock timezone
The clock timezone command allows you to set the t i me zon e for the syst em. T he no clock timezone command changes the system time to Universal Time Coordinated
(UTC).
Use the clock timezone command for display purposes and to manually set the time.
Group Access
System Administrator
Command Mode
Global Configuration
Command Line Usage
clock timezone <WORD > <Hours_offset> [<Minute_offset>] no clock timezone
System Administration Commands
Command Syntax
WORD time zone listed when standard time is in
Hours_offset hours corrected from UTC, range -23 to 23 Minute_offset non-negative difference in minutes corrected
Command Default
UTC
effect
from UTC, range 0 to 59
1-9
Page 40
BSR 64000 Command Reference Guide
configure
The configure command lets you enter Global Configuration mode from Privileged EXEC mode.
Note: To re turn to Privileged EXEC mode, enter exit, end, or Control-Z at the Global Configuration Mode prompt .
Group Access
All
Command Mode
Privileged EXEC
Command Line Usage
configure
1-10
Page 41
console auth entication radius
The console authentication radius command enables RADIUS authentication for user console logins. The no console authentication radius command disables this feature.
Group Access
System Administrator
Command Mode
Global Configuration
Command Line Usage
console authentication radius [ local-password ] no console authentication radius [ local-password ]
System Administration Commands
Command Syntax
local-password authenticate with a locally configured
password if there is no response from the RADIUS server
1-11
Page 42
BSR 64000 Command Reference Guide
copy
The copy command copies a local or network file from one location t o an ot her, eith er locally or on th e network.
Group Access
System Administrator
Command Mode
Privileged EXEC
Command Line Usage
copy {flash: | ftp: | nvram: | running-config | startup-config | system: | tftp:}<file>
| {flash: | nvram: | running-config | startup-config | system:}<file>
Command Syntax
ftp: copy the configuration file from a
File Transport Protocol (FTP) server
nvram: copy the configuration file from
NVRAM
running-config copy from a currently running
system configuration
startup-config copy from the startup configuration
in NVRAM
system: copy from the system tftp: copy the configuration file from a
Trivial File Transport Protocol (TFTP) server
ftp: copy the configuration file to a File
Transport Protocol (FTP) server
nvram: copy the configuration file to
NVRAM
1-12
Page 43
System Administration Commands
running-config copy to the currently running system
configuration
startup-config copy to the startup configuration in
NVRAM
system: copy to thesystem tftp: copy the configuration file to a
Trivial File Transport Protocol (TFTP) server
1-13
Page 44
BSR 64000 Command Reference Guide
disable
The disable command allows you to enter User EXEC mode from the Privileged EXEC mode.
Note: To re turn to Privileged EXEC mode, enter enable at the User EXEC prompt and, if required, a password.
Group Access
System Administrator
Command Mode
Privileged EXEC
Command Line Usage
disable
1-14
Page 45
download runtime nvram:
The download runtime nvram: command allows you to download software contained in an application image file or boot image file stored in Non-Volatile Randon Access Memory (NVRAM) to all modules installed in the BSR 64000. The specified software loads the next time the BSR 64000 is booted.
Group Access
System Administrator
Command Mode
All modes except User EXEC
Command Line Usage
download runtime nvram:<filename>
System Administration Commands
Command Syntax
filename name of the the operating image for
download, such as the application image file or boot image file.
1-15
Page 46
BSR 64000 Command Reference Guide
download slot
The download slot command allows you to specify an image stored in either Non-Volatile Random Access Memory (NRVAM) or flash memory and download it to a resource module installed in the specified chassis slot of the BSR 64000. The specified software loads the next time that the BSR 64000 is rebooted.
Group Access
System Administrator
Command Mode
All modes except User EXEC
Command Line Usage
download slot <NUM> {bm | cmts-fpga | elf | flash:<filesystem> | fp | nvram:<filesystem> | <cr>}
Command Syntax
NUM slot number of the chassis slot holding the
bm downloads the buffer-manager FPGA file
cmts-fpga downloads the cmts-FPGA file stored in the
elf downloads the executable file stored in the
module that will receive the downl oaded fil es or images
stored in the application image (the archive file) fro m NVR AM to the m odule ins tal led in the specified slot.
application image (the archive file) from NVRAM to the module installed in the speci­fied slot.
application image (the archive file) from NVRAM to the module installed in the speci­fied slot.
1-16
Page 47
System Administration Commands
fp downloads the fast-path FPGA file stored in
the application image (the archive file) from NVRAM to the module installed in the speci­fied slot.
flash: downloads an application image or boot
image to the to the module installed in the specified slot from flash memory
nvram: downloads an application image or boot
image to to the mod ule installed in the spec i­fied slot from NVRAM
filesystem name of the operating image intended for
download
<cr> downloads the buffer manager FPGA file, the
CMTS-FPGA file, execu ta ble file, and fast-path F PGA file to th e mod ule ins tall ed in the specified slot
1-17
Page 48
BSR 64000 Command Reference Guide
enable
The enable command allows you to enter Privileged EXEC mode from User EXEC mode.
If the system prompts you for a password, enter the password. After entering Privileged EXEC mode, the prompt changes from the User EXEC mode prompt (hostname>) to the privileged EXEC mode prompt (hostname#).
Group Access
System Administrator
Command Mode
User EXEC
Command Line Usage
enable
1-18
Page 49
enable authentication radius
The enable authentication radius command enables RADIUS authentication for user logins. The no enable authentication radius command disables t h is featu re.
Group Access
ISP
Command Mode
Global Configuration
Command Line Usage
enable authentication radius [ local-password ] no enable authentication radius [ local-password ]
Command Syntax
System Administration Commands
local-password authenticate with a locally configured
password if there is no response from the RADIUS server
1-19
Page 50
BSR 64000 Command Reference Guide
enable password
The enable password command allows you to specify a password associ ated with the enable command. After specifyi ng the password, enter ing the enable command at the
User EXEC prompt causes the system to prompt you for the password. You must supply the password to enter the Privileged EX EC mode. The no enable password command deletes the password.
Group Access
System Administrator
Command Mode
Global Configuration
Command Line Usage
enable password {0 | 7 }<LINE> no enable password
Command Syntax
0 specifies an UNENCRYPTED
7 specifies a HIDDEN password
LINE the password (31 character
password
maximum)
1-20
Page 51
enable secret
The enable secret command allows you to provide an encrypted password that supercedes the enabled password. The no e nable secret command removes the secret.
Use the enable secret command to provide an encrypted password for entering Privileged EXEC mode in the running configuration file when then no service password-encryption command is in effect.
Group Access
System Administrator
Command Mode
Global Configuration
Command Line Usage
System Administration Commands
enable secret [5] <WORD>] no enable secret
Command Syntax
5 specifies an ENCRYPTED secret
WORD the secret (31 character maximum)
1-21
Page 52
BSR 64000 Command Reference Guide
exit
The exit command (used from the Router Confi guration, Interface Configu ration, and Global Configuration modes) accesses the previous command mode in the command mode hierarchy. For example: using the exit command in Interfac e Conf igur at io n mode accesses Global Configuration mode.
Using the exit command in Privileged EXEC or User EXEC modes, ends the command line session.
Group Access
All
Command Mode
All modes
Command Line Usage
exit
1-22
Page 53
forced-download
The forced-download command ensures that boot images are properly downloaded to modules in the BSR 64000 chassis.
Use the forced-download command to ensure that all modules receive the correct boot image before performing an upgrade process or to ensure that a specific module receives the correct boot image before performing an upgrade process.
Group Access
System Administrator
Command Mode
Global Configuration
Command Line Usage
forced-download [<0-15>] no forced-download [<0-15>]
System Administration Commands
Command Syntax
0-15 BSR 64000 slot number
1-23
Page 54
BSR 64000 Command Reference Guide
help
The help command displays instructions for using the CLI help functionality. Refer to the BSR 64000 Configuration and Management Guide for additional instructions on using the CLI help functionality.
Group Access
All
Command Mode
All modes
Command Line Usage
help
1-24
Page 55
history size
The history size command lets you speci fy the size of the hi story buf fer by number of lines. The no his t ory command deletes the history buffer.
Group Access
All
Command Mode
All modes
Command Line Usage
history size <1-256> no history
Command Syntax
System Administration Commands
1-256 the number of lines in the history
Command Default
10
buffer
1-25
Page 56
BSR 64000 Command Reference Guide
hostname
The hostname command configures the name for the system host.
Group Access
System Administrator
Command Mode
Global Configuration
Command Line Usage
hostname <WORD>
Command Syntax
WORD the systems alphanumeric network hostname
1-26
Page 57
ip ftp password
The ip ftp password command displays the password to use to connect to the network using FTP. The no ip ftp password command deletes the password for an FTP connection.
Group Access
System Administrator
Command Mode
Global Configuration
Command Line Usage
ip ftp password 0 password ip ftp password 7 password ip ftp password password no ip ftp password
System Administration Commands
Command Syntax
0 specifies an unencrypted password will
7 specifies a hidden password will follow password password the password (31 character maximum) password
follow
1-27
Page 58
BSR 64000 Command Reference Guide
ip ftp username
The ip ftp username command configures the connection to the network for using FTP. The no ip ftp username command configures the router anonymously for FTP.
Use the ip ftp username command that is related to an account on the server.
Group Access
System Administrator
Command Mode
Global Configuration
Command Line Usage
ip ftp username <WORD> no ip ftp username <WORD>
Command Syntax
WORD username (31 character maximum)
1-28
Page 59
ip netmask-format
The ip netmask-format command le ts you specify the format in which netmask values appear in show command output. The no ip netmask format command sets the output format back to the default.
Group Access
ISP
Command Mode
Global Configuration
Command Line Usage
ip netmask-format {bitcount | decimal | hexadecimal} no ip netmask-format {bitcount | decimal | hexadecimal}
System Administration Commands
Command Syntax
bitcount displays netmask as number of
decimal displays netmask in dotted decimal hexadecimal displays the netmask in hexadecimal
Command Default
bitcount
significant bits
1-29
Page 60
BSR 64000 Command Reference Guide
ldap client
The ldap client command enables the LDAP client. The no ldap client command disables the LDA P client.
Note: Configure a primary or secondary LDAP ser v er addresses before enabling the the LDAP client .
Group Access
System Administrator
Command Mode
Global Configuration
Command Line Usage
ldap client no ldap clie nt
1-30
Page 61
ldap server primary
The ldap server pr imary command estab lishes the IP addr ess and port number of the primary LDAP server for client connections. The no ldap server primary command clears the IP address and port number of the LDAP server.
Group Access
System Administrator
Command Mode
Global Configuration
Command Line Usage
ldap server primary <A.B.C.D> port <1-1024> no ldap server primary <A.B.C.D> port <1-1024>
System Administration Commands
Command Syntax
A.B.C.D the primary LDAP servers IP address
port 1-1024 sets the TCP port assignment for the primary
LDAP server
1-31
Page 62
BSR 64000 Command Reference Guide
ldap search -base
The ldap search-base command speci fies t he b ase dist ingui shed name of t he st artin g point for a searc h of the LDAP database. The no ldap search-base ends t he search of the LDAP database.
Group Access
System Administrator
Command Mode
Global Configuration
Command Line Usage
ldap search-base WORD
Command Syntax
WORD Distinguished name of entry to where the
search will
start
1-32
Page 63
ldap server
The ldap server command configures LDAP server parameters.The no ldap server command clears the LDAP server parameters.
Group Access
System Administrator
Command Mode
Global Configuration
Command Line Usage
ldap server [binddn <WORD>] [nobinddn] [nopassword] [password <WORD>] no ldap server [binddn <WORD>] [nobinddn] [nopassword] [password
<WORD>]
System Administration Commands
Command Syntax
binddn WORD distinguished name nobinddn distinguished name not required to bind to
nopassword password not required password WORD password
this server
1-33
Page 64
BSR 64000 Command Reference Guide
logging
The logging command specifies the IP address of a remote syslog server. The no logging command clears the IP address specification of a remote syslog server.
Group Access
All
Command Mode
Global Configuration
Command Line Usage
logging A.B.C.D no logging A.B.C.D
Command Syntax
A.B.C.D. syslog server IP address
1-34
Page 65
logging buffered
The logging buffered command sets the size of the logging buffer and the severity level. The no logging buffered command returns to the default buffer size (256 KB).
Note: Use the show log command, in User EXEC mode, to di splay logged messages with the new es t m essage d is pl aye d fir st. Use t he de fa ul t l og gi ng buffered command to re turn to the default sett in g.
Group Access
All
Command Mode
Global Configuration
System Administration Commands
Command Line Usage
logging buffered <4096 -16777216> {alerts | critical | debugging | emergencies | errors | informational | notifications | warnings}
no logging buff ered <4096 -16777216> {alerts | critical | debugging | emergencies | errors | informational | notifications | warnings}
Command Syntax
4096 -16777216 logging buffer size in bytes
alerts (severity=1) immediate actions needed critical (severity=2) critical condition debugging (severity=7) debugging messages emergencies (severity=0) system is unusable errors (severity=3) error conditions informational (severity=6) informational messages
1-35
Page 66
BSR 64000 Command Reference Guide
notifications (severit y=5) normal but si gni fica nt condi t ions warnings (severity=4) warning conditions
Command Default
notifications, log file is 256 Kbytes
1-36
Page 67
logging console
The logging co nsole command e nables the sendi ng of system logg ing messages to the console. Additionally, the logging of messages displayed on the console terminal can be limited to a specified severity level. Use the no logging on command to disable system logging.
Group Access
All
Command Mode
Global Configuration
Command Line Usage
logging console [alerts | critical | debugging | emergencies | errors | informational | notifications | warnings]
System Administration Commands
Command Syntax
alerts (severity=1) immediate actions needed critical (severity=2) critical condition debugging (severity=7) debugging messages emergencies (severity=0) system is unusable errors (severity=3) error conditions informational (severity=6) informational messages notifications (severit y=5) normal but si gni fica nt condi t ions warnings (severity=4) warning conditions
Command Default
notifications
1-37
Page 68
BSR 64000 Command Reference Guide
logging facility
The logging facility command specifies the syslog facility to which error messages are sent. The no logging facility command
Group Access
All
Command Mode
Global Configuration
Command Line Usage
logging facilit y {local 0 | local 1 | local 2 | local 3 | local 4 | local 5 | local 6 | local 7} no logging facility
Command Syntax
reverts to the default of local7.
local 0-7 local facility 0 through 7
Command Default
local 7
1-38
Page 69
logging on
The logging on command starts and stops the syslog, and sends debug and error messages to a logging process. The no logging on command stops sending debug or error messages to a logging process.
Use the logging on command to send debug or error messages to a logging process for the syslog to generate th e message to the designated lo cations.
Group Access
All
Command Mode
Global Configuration
Command Line Usage
System Administration Commands
logging on A.B.C.D. no logging on A.B.C.D.
Command Syntax
A.B.C.D. IP address of the host used,
Command Default
no syslog message
1-39
Page 70
BSR 64000 Command Reference Guide
logging rate-limit
The logging rate-l imit command limits the rate of system messages and SNMP traps logged per second. The no logging rate-limit command disables the rate limit.
Group Access
All
Command Mode
Global Configuration
Command Line Usage
logging rate-limit <0-2147483647> [auto-restart] no logging rate-limit
Command Syntax
0-2147483647 the rate of message s logged per second
auto-restart automatically restart the specified rate-limit
1-40
Page 71
logging reporting
The logging reporting command sets the recording mechanism for CMTS messages.
Group Access
All
Command Mode
Global Configuration
Command Line Usage
logging reporting {alert | critical | debu g | emergenc y | err or | information | notice | warning} {all-clear | all-set | local | local-localvol | local-syslog | local-syslog-localvol | local-trap | local-trap-l ocal vol | local-trap-s ysl og | localvol | syslog-localvol | trap-localvol | trap-syslog-localvol}
System Administration Commands
no logging reporting {alert | critical | debug | emergency | error | information | notice | warning} {all-clear | all-set | local | local-localvol | local-syslog | local-syslog-localvol | local-trap | local-trap-l ocal vol | local-trap-s ysl og | localvol | syslog-localvol | trap-localvol | trap-syslog-localvol}
The available logging report options are listed below:
alert Logs conditions where immediate action is needed (severity level 1). critical Logs critical conditions (severity level 2). debug Logs debugging messages (severity level 7). emergency Logs emergency cond itions where th e system is unusable (severi ty level
0).
error Logs error conditions (severity level 3). information Logs informational descriptive system information (severity level 6). notice Logs normal but significant conditions (severity le vel 5). warnings Logs warni ng conditions (severity level 4).
1-41
Page 72
BSR 64000 Command Reference Guide
The location where report messages are logged are listed below:
all-clear Unsets all logging locations for the report. all-set Sets all logging locations for the report. local Log messages for the report go to local-nonvolatile memory
local-localvol Log messages for the report go to local NVRAM and
local-syslog Log messages for th e r epo rt g o to local NVRAM an d the syslog
local-syslog-localvol Log messages for the report go to local NVRAM and local
local-trap Log messages for the report go to local NVRAM. SNMP traps
local-trap-localvol Log messages for the report go to local NVRAM and DRAM
(NVRAM).
local-volatile or "dynamic" memory (DRAM).
server.
DRAM and the syslog server.
are also sent to an SNMP manager.
memory. SNMP traps are also sent to an SNMP manager.
local-trap-syslog Log messages for the report go to local DRAM and a syslog
server. SNMP traps are also sent to an SNMP manager.
localvol Log messages for the report go to local DRAM. syslog-localvol Log messages for the report go to the syslog server and local
DRAM.
trap-localvol Log messages fo r the report g o to loca l DRAM. SNMP traps a re
also sent to an SNMP manager.
trap-syslog-localvol Log messages for the report go to the syslog server and local
DRAM. SNMP traps are also sent to an SNMP manager.
1-42
Page 73
logging reporting default
The logging reporting default command is used to return to the default CMTS log reporting configurati on.
Group Access
All
Command Mode
Privileged EXEC and Global Configuration
Command Line Usage
logging reporting default
System Administration Commands
1-43
Page 74
BSR 64000 Command Reference Guide
logging session
The logging session command enables the transmission of system logging messages to the current login session. The no logging session command disables the transmission of system logging messages to the current login session.
Group Access
All
Command Mode
Privileged EXEC
Command Line Usage
logging session no logging session
1-44
Page 75
logging trap
The logging trap command filters messages logged to the syslog servers based on severity. The command restricts the logging of error messages sent to the syslog servers to only those messages that correspond to a specified severity level. The no logging trap command disables the logging of these messages to the syslog servers.
Group Access
All
Command Mode
Global Configuration
Command Line Usage
logging trap {alerts | critical | debugging | emergencies | errors | informational | notifications | warnings}
System Administration Commands
no logging trap {alerts | critical | debugging | emergencies | errors | informational | notifications | warnings}
Command Syntax
alerts (severity=1) immediate actions needed critical (severity=2) critical condition debugging (severity=7) debugging messages emergencies (severity=0) system is unusable errors (severity=3) error conditions informational (severity=6) informational messages notifications (severit y=5) normal but si gni fica nt condi t ions warnings (severity=4) warning conditions
Command Default
notifications level (severity=5)
1-45
Page 76
BSR 64000 Command Reference Guide
login
The login command logs a user on to the system.
Group Access
All
Command Mode
User EXEC
Command Line Usage
login [<WORD>]
Command Syntax
WORD 1 to 16 character username
1-46
Page 77
logout
The logout command logs a user out of the system. Use the logout command to end the current session. The logout command is used the same way as the exit command.
In Privileged EXEC mode, use t he logout command with a character argument to log a particular user out of the system. Only users with administrative privileges can log other users out.
Group Access
All
Command Mode
User EXEC and Privileged EXEC
Command Line Usage
System Administration Commands
logout [<session-id> | <username>] (Privileged EXEC mode only)
Command Syntax
session-id the session ID number of the user to
username the name of the user to log out
log out
1-47
Page 78
BSR 64000 Command Reference Guide
more
The more command displays the contents of a specified file.
Use the more nvram:startup-conf ig command to view the startup configuration file in NVRAM. The config_file environmental table will be displayed if the startup configuration f ile i s not di spla yed . The user can determine th e stat us of the file which is either a complete or a distilled version of the configuration file.
Use the more system:running-config command to view the running configuration file. The more system:running-config comman d display s the versi on of t he soft ware and any changes that were previously made.
Note: Use the more command to view files on remote systems.
Group Access
System Administrator
Command Mode
Privileged EXEC
Command Line Usage
more {flash: <filename> | ftp: <filename> | nvram: <filename> | nvram:startup-config
Command Syntax
filename file name
| startup-config | system:startup-config }
1-48
Page 79
page
The page command controls the scrolling of system output displays.
Group Access
All
Command Mode
All modes
Command Line Usage
page {off | on}
Command Syntax
off scrolling continues until the end of
System Administration Commands
the display without stopping
on controlled scrolling through the use
Command Default
on
of the Enter/Return key and spacebar
1-49
Page 80
BSR 64000 Command Reference Guide
password
The password command establishes a password that must be specified by users attempting to establish a console or telnet sessio n with the BSR. A console or teln et session will not be est ablis hed if the correct p assword i s not specifie d by t he user. The no passwor d command removes the password.
Group Access
System Administrator
Command Mode
Global Configuration
Command Line Usage
password {console | telnet}[0 | 7]<WORD> no passwor d {console | telnet}
Command Syntax
console password for console connections telnet password for telnet connections 0 specifies an UNENCRYPTED
7 specifies a HIDDEN password
WORD the password (31 character
password
maximum)
1-50
Page 81
radius-server
The radius-server command configures a RADIUS client to allow communication with a RADIUS server. Configuring a RADIUS client involves the following tasks:
specifying the RADIUS server
defining the shared encryption key for authentication between the RADIUS
specifying the number of retry attempts if there is no response from an active
specifying the time i nt erval between retry attempts if there is no response from
Group Access
System Administrator
System Administration Commands
server and the RADIUS client
RADIUS server
from an active RADIUS server
Command Mode
Global Configuration
Command Line Usage
radius-server host {<A.B.C.D>|<Hostname>} [auth-port <0-65535> [primary]] radius-server key <WORD> radius-server retransmit <0-100> radius-server timeout <1-1000>
no radius-server host {<A.B.C.D>|<Hostname>} [auth-port <0-65535> [primary]] no radius-server key <WORD> no radius-server retransmit <0-100> no radius-server timeout <1-1000>
Command Syntax
host specifies a RADIUS server
A.B.C.D the IP address of the RADIUS server Hostname the hostname of the RADIUS server
1-51
Page 82
BSR 64000 Command Reference Guide
auth-port 0-65535 specify a UDP port number for RADIUS
primary select this server as the primary RADIUS
key WORD t ext of the en crypt io n key shared b etwee n th e
retransmit 0-100 specify the number of retry attempts if there is
timeout 1-1000 specify the time interval in seconds between
authentication - default port number is 1812
server
RADIUS client and the RADIUS servers ­Motorola recommends a 22 character minimum
no response from an active RADIUS server ­default is 3 retries
retry attempts if there is no response from from an active RADIUS server - default is 5 seconds
1-52
Page 83
reload
The reload command reloads the operating system. The reload command is most often used to reload upgraded software.
Group Access
System Administrator
Command Mode
Privileged EXEC
Command Line Usage
reload [LINE <LINE> | at <hh:mm:> <LINE> <MONTH> | cancel | fast | in <countdown> <LINE>]
Command Syntax
System Administration Commands
LINE reason to reload
LINE text of the reason to reload
at reloads at a specific time
hh:mm specific hour and minute to reload MONTH name of the month
cancel cancels a pending reload fast reloads the system immediately in reloads after a time interval
countdown time interval in minutes
1-53
Page 84
BSR 64000 Command Reference Guide
reset
The reset command resets all slots or a specific slot in the BSR 64000 chassis.
Group Access
System Administrator
Command Mode
Priviledged EXEC
Command Line Usage
reset {all | <0-6, 9-15>}
Command Syntax
all reset all slots in the BSR 64000 chassis
0-6, 9-15 reset a specific slot
1-54
Page 85
service password-encrypti on
The service password-encryption command enables password encryption. The no service password-encryption disables password encrypt ion.
The service password-encryption command will encrypt previously specified passwords in the running-config file that are currently unencrypted.
Note: Once passwords appearing in the running configuration file are encrypted, the y cannot be unencrypted using the no servi ce
password-encryption command.
Group Access
System Administrator
System Administration Commands
Command Mode
Global Configuration
Command Line Usage
service password-encryption no service password-encryption
Command Default
No encryption
1-55
Page 86
BSR 64000 Command Reference Guide
session-timeout
The session-timeout command lets you specify th e lengt h of ti me (in minute s) befo re the BSR terminates any inactive session. An inactive session is a session has received no user input or system output during the specified time interval.
Group Access
System Administrator
Command Mode
Global Configuration
Command Line Usage
session-timeout {console | telnet} <0-30>
Command Syntax
console specifies console sessions telnet specifies telnet sessions
0-30 length of time in minutes before the
Command Default
5 minutes for telnet sessions 0 for console session (session maintained indefinately)
session is terminated automatically by the BSR
1-56
Page 87
show aliases
The show aliases command displays any one of the following:
Aliases for commands in all modes
Aliases for commands in a specific mode.
Aliases for all commands that begin with, include, or exclude a specified string.
Aliases for a specific mode that begin with, include, or exclude a specified string.
Group Access
All
Command Mode
All except User EXEC
Command Line Usage
System Administration Commands
show alias [conf | exec | priv] [ | ] [ begin | include | exclude ] [<WORD>]
Command Syntax
conf specifies aliases for Global
exec specifies aliases for User EXEC
priv specifies aliases for Privileged
| turns on output mod ifiers (filters) begin filter for output that begins with the
exclude filter for output that excludes the
Configuration mode
mode
EXEC mode
specified string
specified string
1-57
Page 88
BSR 64000 Command Reference Guide
include filter for output that includes the
WORD the specified string
specified string
1-58
Page 89
show boot
The show boot command lists the boot parameters.
Use the show boot command to display the contents of the BOOT environment variables and the configuration register setting.
Group Access
All
Command Mode
All modes except User EXEC
Command Line Usage
show boot [ | ] [begin | exclude | include] [<WORD>]
System Administration Commands
Command Syntax
| turns on output mod ifiers (filters) begin filter for output that begins with the
exclude filter for output that excludes the
include filter for output that includes the
WORD the specified string
specified string
specified string
specified string
1-59
Page 90
BSR 64000 Command Reference Guide
show srm alias
The show srm alias command is used to show the alias name for the SRM module.
Group Access
All
Command Mode
All except User EXEC
Command Line Usage
show srm alias
1-60
Page 91
show chassis alias
The show chassis alias command to show the alias name for the BSR 64000 chassis.
Group Access
All
Command Mode
All modes
Command Line Usage
show chassis alias
System Administration Commands
1-61
Page 92
BSR 64000 Command Reference Guide
show srm assetid
The show srm assetid command is used to view the asset ID number assigned to the SRM.
Group Access
All
Command Mode
All except User EXEC
Command Line Usage
show srm assetid
1-62
Page 93
show chassis assetid
The show chassis assetid command is used to view the asset ID number assigned to your BSR 64000.
Group Access
All
Command Mode
All modes
Command Line Usage
show chassis assetid
System Administration Commands
1-63
Page 94
BSR 64000 Command Reference Guide
show srm serial-num
The show srm serial-num command is used to view the serial number assigned to your SRM.
Group Access
All
Command Mode
All except User EXEC
Command Line Usage
show srm serial-num
1-64
Page 95
show chassis serial-num
The show chassis serial-num command is used to view the serial n umber assigned to your BSR 64000.
Group Access
All
Command Mode
All modes
Command Line Usage
show chassis serial-num
System Administration Commands
1-65
Page 96
BSR 64000 Command Reference Guide
show chassis status
The show chassis status command is used to learn the operational status of the individual modules and upper and lower fan trays on the BSR 64000. This command also alows you to determinine where modules are populated on the BSR 64000. The table below describes the displayed fields.
Field Description
Slot Module slot number from 0 to 15 Type The type of modle inserted into the BSR 64000. HSIM indicates either the
POS or Gigabit Ethernet Network Interface modules (NIMs). CMTS indi­cates the DOCSIS module. SRM indicates the Supervisory Routing Mod­ule.
State Indicates the current operational state of the module. RUN indicates that
the module is ful ly op erat ional. Flash indica tes th at the module is upd atin g its FLASH memory. boot indicates that the module is currently in a boot state.
RM Resource module. An x indicate s that this m odule is operat ional. A - (dash)
indicates that this module is not currently operational.
PM Physical module (IO module). An x indicates that this module is opera-
tional. A - (dash) indicates that this module is not currently operational.
UpTime If the system clock has been set using the clock set command, the
UpTime field displays the amount of time that the module has been opera-
tional. The time is expressed in hh:mm:ss format. LastUpTime If the module is down, the last operational time for the module displays. Success The module booted su cc es sfu lly. Failure The module failed the boot process. Alarms Indicates that alarms are configured for the top and bottom fan trays. Status An x appears in the status field if a fan tray be comes disabl ed. Disabled The disabled column displays no output information at this time. Priority Both fan trays have a critical priority assigned to them.
1-66
Page 97
Group Access
All
Command Mode
All modes
Command Line Usage
show chassis status
System Administration Commands
1-67
Page 98
BSR 64000 Command Reference Guide
show clock
The show clock command shows the system clock.
Group Access
All
Command Mode
All modes
Command Line Usage
show clock [ | ] [begin | exclude | include] [<WORD>]
Command Syntax
| turns on output mod ifiers (filters) begin filter for output that begins with the
specified string
exclude filter for output that excludes the
specified string
include filter for output that includes the
specified string
WORD the specified string
1-68
Page 99
show history
The show history command displays a list of commands executed during a session. The list size is deter mined by the setting of the history size command.
Group Access
All
Command Mode
All modes
Command Line Usage
show history [ | ] [begin | exclude | include] [<WORD>]
Command Syntax
System Administration Commands
| turns on output mod ifiers (filters) begin filter for output that begins with the
specified string
exclude filter for output that excludes the
specified string
include filter for output that includes the
specified string
WORD the specified string
1-69
Page 100
BSR 64000 Command Reference Guide
show log
The show log command displays message logging in the log file the newest message first.The show log command displays log file contents and information about users who have logged into the BSR.
Group Access
All
Command Mode
All modes except User EXEC mode
Command Line Usage
show log [ | ] [begin | exclude | include] [<WO RD>]
Command Syntax
| turns on output mod ifiers (filters) begin filter for output that begins with the
specified string
exclude filter for output that excludes the
specified string
include filter for output that includes the
specified string
WORD the specified string
1-70
Loading...