Motorola Blue Tooth Phone User Manual

TO MAKE INTERCOM / OUTGOING CALLS

To make an intercom call or an outgoing call:

Manual Mode

1. Press the [Answer] button on the headset.

2. Press Extension Number or dial External number

3. To End Call press [Answer] button on headset

Auto Mode

Press Extension number or dial External number
To End Call press SPK button on DK2 Phone

GENERAL OPERATION

To Adjust Speaker Volume during a Call

You can adjust the speaker volume during a call by
pressing the volume control buttons on the side of the Ear
and or the volume control keys on the DK2 phone
according to your preference.

Operation Range

The Hybrex DK2 Blue Tooth Interface is a very low power
radio communication device. The radio communication
range between the DK2 and the Headset is approximately
10 meters. Please keep both units within this range for
best communication performance.

EAR PIECE SETUP

Most headsets will allow you to wear the headset on your
right or left per your preference. Please consult your Blue
Tooth Headset user guide for the setup required.

MAINTAINANCE

As high temperature will shorten the battery life, please do
not leave your Headset in an environment with
temperatures over 100ºF or in direct sunlight.

Keep your Headset away from moisture.

To clean, use soft cloth with mild liquid soap to clean the
exterior of your Cordless Headset and phone. DO NOT

use abrasive chemical detergent or material to clean the
Headset.

DO not attempt to pry open the cover of your Cordless
Headset or change the batteries. Seek assistance from
an AUTHORIZED Hybrex dealer near you.

WARRANTY SCOPE

Auto Telecom guarantees our products (excluding the
batteries) as being free of defects in material, design and
workmanship at the time of original purchase and for a period
of twelve (12) months immediately thereafter.

If, during the warranty period, the products malfunction in
normal use and service (by authorized dealer), Auto
Telecom or its authorized dealer will repair or replace the
defective product at no cost to the original purchaser.

Auto Telecom or its authorized dealer may refuse to
provide free warranty service if any of the following
conditions occurs:

1. The product is adapted, modified, or changed.

2. The product exterior is cracked or broken.

3. The serial number label is tampered with or missing.

4. The product has being misused by the user in any way.

5. The product has not being serviced by a Hybrex
AUTHORSED service agent

Repairs or replacements will neither give any right to
extend the original warranty period nor give any right to
start a new warranty period. Replaced faulty parts or
components will become the property of Auto Telecom.

HEADSET SPECIFICATIONS

Frequency

Security

Technology Type

Auto channel hopping

Working range

Talk time

Blue Tooth Version

2.400~2.4835GHz

128 Bit

Blue Tooth

Yes

Up to 10 meters

4 hours (headset dependant)

1.2

.

Blue Tooth Phone

User Guide

Auto Telecom New Zealand Ltd

Ph [phone]

Fax [phone]

BLUE TOOTH HEADSETS

The Hybrex DK2 Phone Blue Tooth interface will integrate
with many brands of headset, Hybrex have tested and
recommend the following headsets

Motorola HS820

Motorola HS810

Netcom GN6110

CONNECTION TO PHONE

No physical connection to the DK2 phone is required.

TO PAIR HEADSET WITH DK2 PHONE

Before Pairing:

Please ensure Blue Tooth Headset has had its first

maximum charge as recommended by its manufacturer.

• Hold Headset with Mic Boom closed

• Place Blue Tooth Headset into Pairing Mode by

pressing and holding down the answer key until

LED light comes on

• Open Mic Boom, LED on Headset should remain

on

• Press and hold down the DK2 phones “HOLD” key

until “Pairing” is displayed on phone screen

• Release Hold Key

• Waiting until Blue Tooth Headset LED flashes

rapidly

• Phone and Handset are now Paired

Note: Please ensure you only pair one Blue Tooth Device in

the area of work at any one time

TO ACTIVATE DK PHONE INTO HEADSET MODE

To activate the headset mode on DK2 phone:

• Press [SPK][775] to enable the headset mode.

To cancel the headset mode on DK2 phone:

• Press [SPK][775] to cancel the headset mode.

Z248

TO ANSWER INCOMMING CALLS

Manual Mode

To answer incoming call:

• When DK2 phones rings the Blue Tooth Headset will

• To answer call press the [Answer] button on the Blue

To end the conversation of a call:

• Press the [Answer] button again will end the call

• The Blue Tooth Headset will beep to indicate call

Note:

• If you press [SPK] button on the DK2 telephone this

Auto Mode

Headset will be in active when in this mode, please note the

battery time will be more limited when using this mode

To answer incoming call:

• When DK2 phones rings the Blue Tooth Headset will

• The Headset will then answer call

To end the conversation of a call:

• Press the SPK key on the DK2 phone

Note:

• If you press [SPK] button on the DK2 telephone will

beep in your ear

Tooth headset.

ended and will automatically put DK2 phone to
idle state.

will also end the call directly. But the Blue Tooth
Headset will be left in Auto Answer Mode”. If left in
this state the next incoming call will be answered
automatically by the Headset.

beep in your ear once

also end the call directly. But the Blue Tooth
Headset will be left in Auto Answer Mode”. If left in
this state the next incoming call will be answered
automatically by the Headset.

• g range