Coffee 2 go drinks maker
Please read and keep these instructions
getting the best from
your new drinks maker
• Safety first
Caution must be used when handling hot water, coffee or steam.
Ensure the cup setting is correct for the amount of water in
the tank.
• Run water through your machine before first use
It is important to run water through your drinks maker in order to
rinse the machine. You can also run water through to warm your
drinks maker.
• Descale as appropriate for the hardness of the
water in your area
It is important to descale as the performance of your drinks
maker may be impaired by limescale and other impurities in the
water supply.
www.morphyrichards.co.uk
Important safety
instructions
The use of any electrical appliance
requires the following common sense safety
rules.
Primarily there is danger of injury or
death and secondly the danger of damage
to the appliance. These are indicated in the
text by the following two conventions:
WARNING: Danger to the person!
IMPORTANT: Damage to the appliance! In
addition we offer the following safety advice.
Location
• Do not operate any appliance with a
damaged cord or plug or after the
appliance malfunctions or has been
damaged in any manner. Ring the
helpline number for advice on
examination and repair.
• The use of attachments or tools not
recommended or sold by Morphy
Richards may cause fire, electric shock
or injury.
•Do not use abrasive cleaners on the
outside of the drinks maker, they may
scratch the surface. Clean only with a
soft damp cloth.
• Do not use the drinks maker for anything
other than its intended purpose.
• Remove all the packaging and retain for
future reference.
• Ensure the drinks maker is used on a
firm, flat, heat resistant surface.
• Do not use the drinks maker outdoors or
in a bathroom.
• Do not place the drinks maker on a
highly polished wooden surface as
damage may occur to the surface.
• Do not place the drinks maker on or near
hot surfaces such as a hot plate or
radiant rings or near a naked flame.
•WARNING: Do not place the drinks
maker onto a metal tray or metal
surface whilst in use.
Children
• Children do not understand the dangers
associated with operating electrical
appliances. Never allow children to use
this appliance.
Other safety considerations
• Disconnect the drinks maker from the
mains supply when filling, cleaning or
not in use.
•Keep the outside of the drinks maker
area clean and dry at all times.
• Do not touch hot surfaces. Always use
handles or knobs.
• Do not immerse the drinks maker itself in
water and always ensure the electrical
connections are kept dry.
Product safety
• Never use warm or hot water to fill the
water reservoir.
• Do not overfill the water reservoir.
Treating scalds
•Run cold water over the affected area
immediately. Do not stop to remove
clothing, get medical help quickly.
Personal safety
• Do not fill above the capacity of the
water level indicator marked.
• Do not touch metal parts until the unit
has cooled down.
• Do not remove the thermal cups until the
brewing process has completely
finished.
•Warning: Ensure that the amount of
water put in is correct for the cup
setting on the top of the unit before
beginning the brewing process.
• Always put both cups in place even
when only brewing into one cup.
•Warning: Hot drinks will scald, drink
with caution.
2
Electrical requirements
Check that the voltage on the rating plate
of your appliance corresponds with your
house electricity supply which must be A.C.
(Alternating current).
For appliances with fitted plug.
If the socket outlets in your home are not
suitable for the plug supplied with this
appliance the plug should be removed and
the appropriate one fitted.
Features
Permanent
filter
basket x 2
Filter basket
holders x 2
Integral
cup lid
One/two cup
selector switch
WARNING: The plug removed from the
mains lead, if severed, must be destroyed
as a plug with bared flexible cord is
hazardous if engaged into a live socket
outlet.
Should the fuse in the 13 amp plug
require changing a 13 amp BS1362 fuse
must be fitted.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
Water reservoir
cover
Water reservoir x 2
Water level
indicator
Thermal
cups x 2
Measuring
spoon
The first time you use your drinks maker
Before using your drinks maker the first time,
operate with water only.
LCD display
Power
switch
with led
light
Prog
(Programme)
button
Clock
button
Hour
button
Minute
button
3
Brewing coffee
Brewing tea
1 Set the dial on top of
the unit to one or two
cups, as required.
2 Fill the water reservoir
to the one or two cup
level as appropriate.
Do not overfill the
reservoir, only put in
the exact amount
required.
3 Swing the filter
holder/s out, ensure
that the permanent
filter has been fitted
and fill the filter basket
with 3 scoops per cup
(adjust according to
taste) of filter coffee
grounds.
When brewing one
cup only, the unit will
fill into the LEFT
hand side. Therefore
put the coffee in the
left hand filter.
4 Close the filter holder/s ensuring that
they click back into place.
5 Fit both the thermal cups (with lids in
place) into the unit even if brewing one
cup only.
6 Plug the drinks maker into the mains
supply.
7 When the unit is plugged in, the display
will show “00:00” as no time is set. The
red light in the centre of the power
button will show that the power is on.
8 To begin brewing immediately, press the
power button. The green LED will light as
brewing starts.
9 Once the unit has finished brewing, the
red LED will glow and the unit will beep
5 times.
10 The brewing process can be stopped at
any time by pressing the power button.
Warning: Remove the lids with
extreme caution in order to add milk
and/or sugar as required.
1 Set the dial on top of the unit to one or
two cups, as required.
2 Fill the water reservoir to the one or two
cup level as appropriate. Do not overfill
the reservoir, only put in the exact
amount required.
3 Swing the filter holder/s out, remove the
filter basket/s and put one or two
teabags per cup (according to taste),
directly into the filter holder.
When brewing one cup only, the unit
will fill into the LEFT hand side.
Therefore put the teabag in the left
hand filter holder.
4 Close the filter holder/s ensuring that
they click back into place.
5 Fit both the thermal cups (with the lids in
place) into the unit even if brewing one
cup only.
6 Plug the drinks maker into the mains
supply.
7 When the unit is plugged in, the display
will show “00:00” as no time is set. The
red light in the centre of the power
button will show that the power is on.
8 To begin brewing immediately, press the
power button. The green LED will light as
brewing starts.
9 Once the unit has finished brewing, the
red LED will glow and the unit will beep
5 times.
10 The brewing process can be stopped at
any time by pressing the power button.
Warning: Remove the lids with
extreme caution in order to add milk
and/or sugar as required.
HINT: When brewing into two cups, a
combination of drink types can be
produced. For example: a cup of tea and a
cup of coffee or a cup of coffee and a cup
of hot chocolate etc.
Thoroughly wash the cups and all
removable parts after use, as described in
‘Cleaning care’.
4
Hot chocolate and hot
Drinking cups
blackcurrant
1 Set the dial on top of the unit to one or
two cups, as required.
2 Fill the water reservoir to the one or two
cup level as appropriate. Do not overfill
the reservoir, only put in the exact
amount required.
3 Fill the thermal cup/s with the desired
amount of hot chocolate powder or
blackcurrant concentrate.
When brewing one cup only, the unit
will fill into the LEFT hand side.
Therefore put the powder or juice in
the left hand cup.
4 Fit both the thermal cups (with the lids in
place) into the unit even if brewing one
cup only.
5 Plug the drinks maker into the mains
supply.
6 When the unit is plugged in, the display
will show “00:00” as no time is set. The
red light in the centre of the power
button will show that the power is on.
7 To begin brewing immediately, press the
power button. The green LED will light as
brewing starts.
8 Once the unit has finished brewing, the
red LED will glow and the unit will beep
5 times.
9 The brewing process can be stopped at
any time by pressing the power button.
Warning: Remove the lids with
extreme caution and stir.
HINT: When brewing into two cups, a
combination of drink types can be
produced. For example: a cup of tea and a
cup of coffee or a cup of coffee and a cup
of hot chocolate etc.
• The drinking cups are portable and can
be used on the move.
• There is a rotating cap on the top of the
lid which helps to
retain the heat when
you are not drinking.
When you wish to take
a drink, simply turn
the cap in the
direction indicated by
the arrow and
carefully drink from
the cup.
Warning: Due to the risk of scalding,
take care not to over pour the cup as you
drink.
Warning: Remove the lids with
extreme caution.
Warning: Even though the cups are
portable, do not drink anything whilst
driving.
Setting the clock
• Press the “CLOCK” button to begin
setting the current time.
• The digits on the display will flash
“00:00”.
• Press the “HOUR” button repeatedly
until the current hour is displayed.
• Press the “MINUTE” button repeatedly
until the current minutes past the hour
are displayed.
• Press the “CLOCK” button and the time
setting is complete.
Thoroughly wash the cups and all
removable parts after use, as described in
‘Cleaning care’.
5
Setting the product to
Guide to LED indicator
brew at a preset time
1 Set up the drinks maker for brewing as
described previously.
2 Ensure that the clock is set up as
described in ‘setting the clock’.
3 Press the “PROG” button to begin
setting the automatic brew time.
4 The digits on the display will flash.
5 Press the “HOUR” button repeatedly
until the desired brewing hour is
displayed.
6 Press the “MINUTE” button repeatedly
until the minutes past the brewing hour
are displayed.
7 Press the “PROG” button and the
automatic time setting is complete.
8 The LED will flash green until the
brewing process time is reached.
9 Once the brewing time has been
reached, the unit will beep 3 times and
the green LED will glow.
10 After the unit has finished brewing, the
red LED will glow and the unit will beep
5 times.
NOTE: If at any time you decide not to
have the unit set to a preset time, simply
press the “Power“ button until the LED
glows red.
• No LED
Unit is not plugged in.
• Red LED
Unit is plugged in, but not set to brew or
has completed brewing.
• Green flashing LED
Unit is set to brew at a preset time.
• Green LED
Unit is in the process of brewing.
6
Descaling
Cleaning care
• If you live in a hard water area, we
recommend that your drinks maker is
descaled at regular intervals, e.g. every
2-3 months. In areas of moderately hard
water you should descale every 6
months.
• If the water filters through more slowly
than usual, it is a sign that descaling is
necessary.
•We recommend you use proprietary
liquid descaler which is especially made
for coffee/drinks makers and plastic
kettles. Follow the instructions on the
bottle or sachet, and then operate the
drinks maker with just water 3 times
before making drinks.
• Do not use kettle descaler unless the
packet specifically states it is suitable for
coffee/drinks makers.
Note: The permanent mesh filters should
not be used during descaling.
Unplug the drinks maker and allow to
cool.
Do not immerse the drinks maker in
liquid.
Rinse the water
reservoir occasionally with
cold water. Do not use a
cloth as any residue or lint
may be left behind to clog
the drinks maker.
Remove the permanent
filter basket, discard used
coffee and teabags and
wash thoroughly.
Extended soaking helps to
remove tea and coffee
stains from the mesh.
Swing the filter holder
fully back and lift upwards
to remove.
To refit filter holder
locate in upper slot, re-align and slot bottom
tab into place.
Wipe all external surfaces with a damp
cloth and dry thoroughly.
Never use harsh or abrasive cleaners.
ALL WASHABLE PARTS ARE
DISHWASHER SAFE.
Helpline
If you have any difficulty with your
appliance, do not hesitate to call us.
We are more likely able to help than the
store from where you bought it.
Please have the following information
ready to enable our staff to deal with your
query quickly.
• Name of the product
• Model number and serial number as
shown on the underside of the appliance.
7
Your two year guarantee
It is important to retain the retailers receipt
as proof of purchase. Staple your receipt to
this back cover for future reference.
Please quote the following information if
the product develops a fault. These numbers
can be found on the base of the product.
Model no. Serial no.
All Morphy Richards products are
individually tested before leaving the factory.
In the unlikely event of any appliance proving
to be faulty within 28 days of purchase it
should be returned to the place of purchase
for it to be replaced.
If the fault develops after 28 days and
within 24 months of original purchase, you
should contact the Helpline number quoting
Model number and Serial number on the
product, or write to Morphy Richards at the
address shown.
You will be asked to return the product (in
secure, adequate packaging) to the address
below along with a copy of proof of
purchase.
Subject to the exclusions set out below
(see Exclusions) the faulty appliance will then
be repaired or replaced and dispatched
usually within 7 working days of receipt.
If for any reason this item is replaced
during the 2 year guarantee period, the
guarantee on the new item will be calculated
from original purchase date. Therefore it is
vital to retain your original till receipt or
invoice to indicate the date of initial
purchase.
To qualify for the 2 year guarantee the
appliance must have been used according to
the manufacturers instructions. For example
coffee makers/kettles should have been
regularly descaled.
EXCLUSIONS
Morphy Richards shall not be liable to
replace or repair the goods under the terms
of the guarantee where:
1 The fault has been caused or is
attributable to accidental use, misuse,
negligent use or used contrary to the
manufacturers recommendations or where
the fault has been caused by power
surges or damage caused in transit.
2 The appliance has been used on a voltage
supply other than that stamped on the
products.
3 Repairs have been attempted by persons
other than our service staff (or authorised
dealer).
4 Where the appliance has been used for
hire purposes or non domestic use.
5 Morphy Richards are not liable to carry
out any type of servicing work, under the
guarantee.
6 Plastic filters for all Morphy Richards
kettles and coffee makers are not covered
by the guarantee.
This guarantee does not confer any rights
other than those expressly set out above and
does not cover any claims for consequential
loss or damage. This guarantee is offered as
an additional benefit and does not affect your
statutory rights as a consumer.
• This guarantee is valid in the UK and
Ireland only.
Morphy Richards products are intended for
household use only.
Morphy Richards has a policy of continuous
improvement in product quality and design.
The company, therefore reserves the right
to change the specification of its models at
any time.
The After Sales Division
Registered address
Morphy Richards Ltd, Mexborough
South Yorkshire, England, S64 8AJ
Helpline (office hours)
UK (local rate) 0870 060 2610
Republic of Ireland 1800 409119
CM47071M UK Rev 1
Loading...