Mitsubishi Electronics X50, X70 User Manual

LCD Projector User Manual
ENGLISH
FRANÇAISDEUTSCHITALIANOESPAÑOL
X 5 0 X 7 0
MODEL LVP-X50U / LVP-X70U
EN – 1
CAUTION
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the litera­ture accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
NOTE:
SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE IN­STALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.
WARNING
Use the attached specified power supply cord. If you use another power-supply cord, it may cause interfer­ence with radio and television reception.
Use the attached RGB cable, RS-232C cable with this equipment so as to keep interference within the limit of a FCC Class A device.
This apparatus must be grounded.
The projector automatically shuts off when the lamp is used up in about 2,000 hours and cannot be used until lamp replacement.
DO NOT LOOK DIRECTLY INTO THE LENS WHEN PROJECTOR IS IN THE POWER ON MODE.
When using the projector in Europe COMPLIANCE NOTICE
This LCD - Video Projector complies with the requirements of the EC Directive 89/336/EEC “EMC Directive” as amended by Directive 93/68/EEC and 73/23/EEC “Low Voltage Directive” as amended by Directive 93/68/EEC.
The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on small-scale enterprises, inside as well as outside of the buildings. All places of operation are characterised by their connection to the public low voltage power supply system.
WARNING
Use the attached RGB cable or RS-232C cable with this equipment so as to keep interference within the limits of a EN55022 Class B and EN55013. Please follow WARNINGS instructions.
EN – 2
Contents
Important safeguards ...........................................................................4
Overview ............................................................................................... 6
Using the remote control ......................................................................8
Battery installation ......................................................................................................... 8
Installation ............................................................................................9
Basic connections ............................................................................... 10
Projector + AV equipment............................................................................................. 10
Projector + DVD player or HDTV decoder ................................................................... 10
Projector + personal computer...................................................................................... 11
For IBM PC or IBM PC compatibles................................................................. 11
For Macintosh .................................................................................................... 11
Preparing the projector for operation ............................................... 12
To operate projector power ON.......................................................... 13
Menu operation .................................................................................. 15
Picture adjustment............................................................................. 18
Specification of RGB signals in each computer mode of the projector ....................... 20
Advanced feature for presentation .................................................... 21
Expand ........................................................................................................................... 21
PinP (Picture in Picture)............................................................................................... 21
Still................................................................................................................................. 21
Mouse remote control .................................................................................................... 22
Lamp replacement ............................................................................. 23
ENGLISH
Maintenance ....................................................................................... 24
Troubleshooting.................................................................................. 25
Indicators ............................................................................................ 26
Specifications ...................................................................................... 27
Kensington Lock............................................................................................................ 27
Connectors ..................................................................................................................... 28
Dimensional drawings .................................................................................................. 28
What’s included in the box............................................................................................ 28
Replacement part .......................................................................................................... 28
E
Trademark, Registered trademark
Macintosh is registered trademark of Apple Computer Inc. IBM and VGA are trademarks or registered trademarks of International Business Machines Corporation. MicroSaver and Kensington are registered trademarks of Kensington Technology Group. Other brand or product names are trademarks or registered trademarks of their respective holders.
EN – 3
Important safeguards
Please read all these instructions regarding your LCD projector and retain them for future reference. Follow all warnings and instructions marked on the LCD pro­jector.
1. Read instructions All the safety and operating instructions should be read before the appliance is operated.
2. Retain instructions The safety and operating instructions should be retained for future reference.
3. Warnings All warnings on the appliance and in the oper­ating instructions should be adhered to.
4. Instructions All operating instructions must be followed.
5. Cleaning Unplug this projector from the wall outlet be­fore cleaning it. Do not use liquid aerosol clean­ers. Use a damp soft cloth for cleaning.
6. Attachments and equipment Never add any attachments and/or equipment without the approval of the manufacturer as such additions may result in the risk of fire, elec­tric shock or other personal injury.
7. Water and moisture Do not use this projector near water or in con­tact with water.
8. Accessories Do not place this projector on an unstable cart, stand, tripod, bracket or table. Use only with a cart, stand, tripod bracket, or table recommended by the manufacturer or sold with the projector. Any mounting of the appliance should follow the manufacturer's instructions and should use a mounting accessory recommended by the manu­facturer.
An appliance and cart combination should be moved with care. Quick stops, excessive force and uneven surfaces may cause the appliance and cart combination to overturn.
9. Ventilation Slots and openings in the cabinet are provided for ventilation, ensuring reliable operation of the projector and to protect it from overheating. Do not block these openings or allow them to be blocked by placing the projector on a bed, sofa, rug, or bookcase. Ensure that there is adequate ventilation and that the manufacturer's instruc­tions have been adhered to.
10. Power sources This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power, please consult your appliance dealer or local power company.
11. Power-cord protection Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular at­tention to cords at plugs, convenience receptacles, and points where they exit from the appliance.
12. Overloading Do not overload wall outlets and extension cords as this can result in a fire or electric shock.
13. Objects and liquids Never push objects of any kind through open­ings of this projector as they may touch danger­ous voltage points or short-out parts that could result in a fire or electric shock. Never spill liq­uid of any kind on the projector.
14. Servicing Do not attempt to service this projector yourself. Refer all servicing to qualified service person­nel.
15. Damage requiring service Unplug this projector from the wall outlet and refer servicing to qualified service personnel un­der the following conditions: (a) If the power-supply cord or plug is dam-
aged.
(b) If liquid has been spilled, or objects have
fallen into the projector.
(c) If the projector does not operate normally
after you follow the operating instructions. Adjust only those controls that are covered by the operating instructions. An improper adjustment of other controls may result in damage and may often require exten­sive work by a qualified technician to re­store the projector to its normal operation.
(d) If the projector has been exposed to rain
or water.
(e) If the projector has been dropped or the
cabinet has been damaged.
(f) If the projector exhibits a distinct change
in performance - this indicates a need for service.
16. Replacement parts When replacement parts are required, be sure that the service technician has used replacement parts specified by the manufacturer or parts having the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.
17. Safety check Upon completion of any service or repair to this projector, ask the service technician to perform safety checks determining that the projector is in a safe operating condition.
EN – 4
WARNING: Unplug immediately if there is something wrong with your projector.
Do not operate if smoke, strange noise or odor comes out of your projector. It might cause fire or electric shock. In this case, unplug immediately and contact your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An inadvertent contact may result in an electric shock. Except as specifically explained in the Owner's Guide, do not attempt to service this product yourself. Please contact your dealer when you want to fix, adjust or inspect the projector.
Do not modify this equipment.
It can lead to fire or electric shock.
If you break or drop the cabinet.
Do not keep using this equipment if you break or drop it. Unplug the projector and contact your dealer for inspection. It may lead to fire if you keep using the equipment.
Do not face the projector lens to the sun.
It can lead to fire.
Use correct voltage.
If you use incorrect voltage, it can lead to fire.
Do not place the projector on uneven surface.
Place the projection on a leveled and stable surface only. Please do not place equipment on unstable surfaces. Do not look into the lens when it is operating. It may hurt your eyes. Never let children look into the lens when it is on.
Do not turn off the main power abruptly or unplug the projector during operation.
It can lead to lamp breakage, fire, electric shock or other trouble. It is best to wait for the fan to turn off before turning main power off.
Place of installation
For safety’s sake, refrain from setting the projector at any place subjected to high temperature and high humidity. Please maintain an operating temperature, humidity, and altitude as specified below.
• Operating temperature: between +41°F (+5°C) and +95°F (+35°C)
• Operating humidity: between 30 and 90%
• Never put any heat-producing device under the pro­jector so that the projector does not overheat.
• Do not attach the projector to a place that is un­stable or subject to vibration.
• Do not install the projector near any equipment that produces a strong magnetic field. Also refrain from installing near the projector any cable carrying a large current.
• Place the projector on a solid, vibration free sur­face: otherwise it may fall, causing serious injury to a child or adult, and serious damage to the prod­uct.
• Do not stand the projector: it may fall, causing seri­ous injury and damage to the projector.
• Place the projector within a slope of ±15˚. Slanting the projector more than ±15˚ may cause trouble or explosion of the lamp.
• Do not place the projector near air-conditioning unit or heater to avoid hot air to the exhaust and venti­lation hole of the projector.
ENGLISH
COMPLIANCE NOTICE OF FCC
This equipment has been tested and found to comply with the limits for a Class A digital device, pursu­ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This digital apparatus does not exceed the Class A limits for radio noise emissions from digital appara­tus as set out in the interference-causing equipment standard entitled “Digital Apparatus”, ICES-003 of the Department of Communications.
Changes or modifications not expressly approved by Mitsubishi could void the user's authority to oper­ate this equipment.
COMPLIANCE NOTICE OF INDUSTRY CANADA
This Class A digital apparatus complies with Canadian ICES-003.
EN – 5
Overview
11
12
7
8
56910
1 Air inlet grill (Front) 2 Front height adjuster button 3 Air inlet grill (Side) 4 Terminal board 5 Speaker 6 Remote control sensor (Front) 7 Zoom ring 8 Focus ring 9 Control panel 10 Lens 11 Kensington Security Lock Standard
2
314
connector 12 Remote control sensor (Rear) 13 Air outlet grill
13
Control panel
POWER
1
LAMP
VOLUME
TEMP
2345
Terminal board
RS-232CUSB
COMPUTER
SOURCE
VIDEO
COMPUTER INCOMPUTER OUT
VIDEO IN
AUTO POSITION
MENU
S-VIDEO
VIDEO
AUDIO L
(MONO)
AUDIO R
456789
ENTER
MAIN
AC IN
89101112
MUTE
OI
1 LAMP indicator 2 TEMP (temperature) indicator 3 + , – (VOLUME) button 4 VIDEO button 5 MENU button 6 ENTER button 7 Direction buttons 8 MUTE button
7
9 AUTO POSITION button 10 COMPUTER button 11
6
Power button 12 Power indicator
1 Ground terminal 2 Power jack 3 Main power
– : ON O : OFF
4 Video/audio input terminals 5 Reset button 6 COMPUTER IN terminal (D-SUB mini 15P) 7 COMPUTER OUT terminal (D-SUB mini 15P)
3
8 RS-232C (DIN 8P) terminal 9 USB terminal
2
EN – 6
1
Bottom side
3
1 Adjustment foot (right and left) 2 Lamp cover 3 Adjustment foot (up and down)
ENGLISH
Caution:
Do not replace the lamp right after using the projector. The lamp is very hot.
2
1
Remote control
1
2
3
4
5
6
7 8
9
17
POWER MUTE
COMPUTER
MOUSE LASER
R-CLICK
MENU ENTER
AUTO POSITION
P in P EXPAND
VOLUME–+
VIDEO
STILL
16
15 14
13
12
11 10
AVOID EXPOSURE -LASER
RADIATION IS EMITTED FROM THIS APERTURE.
1 Transmitter indicator 2 Power button 3 COMPUTER button 4 Mouse button 5 Right click button (For mouse) 6 MENU button 7 AUTO POSITION button 8 PinP button (For LVP-X70U only) 9 + , – (VOLUME) buttons 10 EXPAND button 11
STILL button 1
2 ENTER button 13 Mouse pointer / Direction buttons 14 LASER button 15 VIDEO button 16 MUTE button 17 Laser aperture 18 Left click button (For mouse)
When pressing Mouse button, it illuminates and
Direction buttons work as the mouse pointer. Press the Mouse button or MENU button to set off. (Direc­tion buttons work as Direction buttons.)
Pressing LASER button emits the laser beam about
1 minute. Release LASER button and press it again if you wish to emits the laser beam.
18
About laser beam
This remote control is class 2 (max. output 1 mW laser diode 640 - 660 nm) laser equipment. Beam Divergence : 3m distance about 5.0mm x 3.0mm (±1.5mm)
CAUTION
LASER RADIATION DO NOT STARE INTO BEAM
WAVE LENGTH : 640 - 660nm MAX OUTPUT : 1mW
CLASS 2 LASER PRODUCT IEC 60825-1:1993+A1:1997
CAUTION :
• Pressing the LASER button provided remote control emits laser beam. Do not look into the beam light directly. Do not point the laser beam at people. Looking the laser beam directly may damage eyesight.
• Use of controls or adjustments or procedures other than those specified herein may result in hazardous radiation exposure.
EN – 7
Using the remote control
Battery installation
Use two AAA size batteries.
1. Remove the back cover of the remote control by pushing the battery compartment door in the direction of the arrow.
2. Load the batteries making sure that they are positioned correctly (+ to +, and - to -).
• Load the batteries from - spring side, and make sure to set them tightly.
3. Replace the back cover.
12 3
Important:
• Do not combine a new battery with an old one.
• Load batteries in the correct position.
• Do not heat, take apart, or throw batteries into fire.
• Do not try to recharge batteries. Do not use rechargeable batteries.
• If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in contact with your eyes, rinse them with water and then consult your doctor.
Operation area
The range for operation is about 10 m (33 feet) when the remote control points to the projector. The distance to the screen back to the projector must be less than 6 m (20 feet). Depending on the type of the screen, the distance is different.
20˚ 15˚
Important:
Avoid the direct sunlight or fluorescent light to the remote control sensor. Also keep the distance of more than 2 m between the remote control sensor and fluorescent lamp on the remote control may not work correctly.
20˚ 15˚
30˚30˚
EN – 8
Installation
Orientation of the projector
Picture size can be set by changing the distance between the screen and the projector.
Front projection
screen
To find the approximate distance be­tween the projector and screen: Multiply the width of the screen
1.7 (min.) , Multiply the width of the screen 2.4 (max.).
• Refer to the chart for recommended distances in maximum zoom and minimum zoom.
ENGLISH
H
Diagonal size
(inch)
40 " 60 "
80 " 100 " 120 " 140 " 160 "
180" 200 " 300 "
• The above numbers are approximate, and may be slightly different from the actual measurements.
Ceiling mount, Rear projection
Ask a specialist for installation. For more details, consult your dealer.
Caution:
• Placing the projector on a carpet reduces ventila­tion from the fan at the bottom and might cause problems. Place a hard board or similar item under the projector to facilitate ventilation of the unit.
• Place the projector more than 50 cm (20 inch) from the wall to prevent blocking the intake, exhaust slots and ventilation of this projector because hot air comes out of it.
(between the screen and
L
the head of the projector)
Screen
Height inches
(inch)
24 " 36 " 48 " 60 " 72 " 84 "
96 " 108 " 120 " 180 "
Width feet
(inch)
32 " 48 " 64 " 80 "
96 " 112 " 128 " 144 " 160 " 240 "
Distance from screen (L) / (approximate)
Maximum
zoom (WIDE) (cm)
140 213 286 360 433 506 579 652 725
1070
(inch)
55 "
84 " 113 " 142 " 171 " 199 " 228 " 257 " 285 " 421 "
Minimum
zoom (TELE)
(cm)
184 279 374 469 564 659 754 849 944
1393
(inch)
72 " 110 " 147 " 185 " 222 " 259 " 297 " 334 " 372 " 548 "
• Do not use the projector under the following circumstances, which may cause fire or electric shock.
• in a dusty or humid place
• while the projector is lying sideways or upside
down
• near a heater
• in a kitchen or oily, smoky or damp place
• in direct sunlight
• with high temperature, such as the closed car
• where the temperature is lower than 41°F or
higher than 95°F
Important:
• Do not add stress on the lens, as this may cause damage.
Height projected
(cm)
6.1
9.1
12.2
15.2
18.3
21.3
24.4
27.4
30.5
45.7
image (H)
(inch)
2.4 "
3.6 "
4.8 "
6.0"
7.2 "
8.4 "
9.6 "
10.8 "
12.0 "
18.0 "
´ EN – 9
Basic connections
This projector can be connected to equipment such as PC, VCRs, video cameras and DVD players.
Important:
• Make sure that your equipment is turned off before connection.
• Plug in firmly and unplug by holding the plug, not by pulling the AC power cord.
• If connected units are set too close to one another, the image may be affected.
• Refer to the user manual of each component for details of connections.
Projector + AV equipment
Important:
• Match the color of video and audio plugs on the AV cable with the connections.
• S-video signals take priority over video signals. If you input both S-video signals and normal video signals at the same time, the normal video input automatically is inhibited.
Connect either one of these.
Ferrite core
to S-video
output
to video
output
to audio
VCR etc.
output
• Speaker output is mono.
• Select AUDIO MODE 2 to hear and to sound for the VIDEO. (Refer to page 16).
• When connecting audio output of equipment which audio output is mono, connect to audio input L terminal.
to S-video
input
to video
input
to audio
input
Projector + DVD player or HDTV decoder
Some DVD players have output terminal for 3 line fitting (Y, CB, CR). When connecting them to the projector, connect to COMPUTER IN of the projector. In this case, set “ Y, CB, CR” for COMPUTER INPUT setting in SIGNAL menu.
DVD player generally has SDTV system component video output (Y, CB, CR) terminals. HDTV decoder has HDTV system component video output (Y, PB, PR) ter­minals. When connecting the projector with DVD player or HDTV decoder, the signal cuircuit automaticaly applied to either of them. In this case, the COMPUTER INPUT in the SIGNAL menu becomes [Y, CB, CR/Y, PB, PR].
• Y, PB, PR is an example of the terminal names for a HDTV decoder.
• The terminal name is different depending on the connected equipment.
• Use mini D-SUB 15 pin-BNC conversion cable for connection.
• Some DVD players may not project the image correctly.
• When connecting with HDTV equipment which has R, G, B output, set RGB for the COMPUTER INPUT in the SIGNAL setting menu.
• Change the setting in the SIGNAL menu, when 525p signal is inputted. (Refer to page 20).
DVD player or HDTV decoder
CB(PB)Y CR(PR)
R
HD/CS VD
B G
Mini D-SUB 15 pin-BNC conversion cable (optional)
BNC-RCA connector (optional)
No connection
to COMPUTER
IN
EN – 10
to video port
computer
MAC adapter for RGB cable (Optional)
Monitor Conversion adapter (optional)
RGB cable for PC
Monitor cable (optional)
to AUDIO IN
to PC audio output
to COMPUTER IN
to COMPUTER OUT
1 2 3 4 5 6
ON DIP
PC audio cable (optional)
When outputting to both a PC monitor and the projector.
to PC monitor
Projector + Personal computer
Connection
For IBM PC or IBM PC compatibles
For Macintosh
When outputting to both a PC monitor and the projector.
to COMPUTER OUT
to AUDIO IN
to COMPUTER
IN
RGB cable for PC (optional)
PC audio cable (optional)
RGB cable for PC
to PC audio output
ENGLISH
computer
to PC monitor
to monitor port
Important:
• Connectors or analog RGB output adapters may be necessary depending on the PC connected to this projector. Please contact your dealer.
• The audio input for this projector is a stereo pin jack. (Speaker output is mono.) Please check the available cable for the audio input terminal of the PC. Some personal computer may not have the audio output terminal.
• Select AUDIO MODE 1 to hear and to sound for the COMPUTER. (Refer to page 16).
• When connecting audio output of a personal computer which audio output is mono, connect to the audio input L terminal.
For using Macintosh
• A monitor output adapter is necessary for a Macintosh if it has no video port. Please contact your dealer.
• A MAC adapter for RGB cable may be necessary depending on the personal computer connected to this projec­tor. Please contact your dealer.
´ EN – 11
Preparing the projector for operation
A
Getting ready for projection
1. Connect the power cord provided to the projector.
2. Connect the power cord to the wall power outlet.
3. Remove the lens cap.
Warning:
• Do not look directly into the lens when projector is “ON”.
• The lens cap is for protecting the lens. If you leave the power on with the cap on, the cap may be warped. Please remove the lens cap when you turn the power on.
• This projector is equipped with the power cords for both U.S. and Europe. Use the appropriate power cord for your country.
• A three-pin grounding type power plug is used with the projector. Do not remove the grounding pin on the power plug. If you are unable to insert the plug into the outlet, contact your electrician to replace your A/C outlet.
• The supplied power cord for U.S. is used for 120V only. Never connect to any outlet or power supply having a different voltage or frequency. If you connect to the power supply having a different voltage, please use the appropriate power cord.
• Use 100-240V AC 50/60Hz correct voltage other­wise it may lead to fire or electric shock.
• Do not place any objects on the power cord, and keep the projector away from heat sources to avoid break­ing the power cord. A broken power cord can cause fire or electric shock.
• Do not revise or alter the power cord otherwise it may cause fire or electric shock. Contact your dealer if the cord is broken.
Caution:
• Plug in firmly and unplug by holding the plug, not by pulling the cable out.
• Do not plug in or out with wet hands. It may cause an electric shock.
Adjusting the angle of projection
For the best result, project onto a flat screen with a 90 degree angle to the floor. If necessary, tilt the projector by adjusting two foot adjustments on the bottom of the projector.
screen
1. Lift the projector to the appropriate angle.
2. Press the Front height adjuster button, this will al­low the adjustment foot (up and down) to slide out to the position.
3. Release the Front height adjuster button to lock the feet in that position.
Front height adjuster button
djustment foot
(up and down)
After using the projector
4. Return the adjustment foot (up and down) into the projector by pressing the Front height adjuster but­ton.
When the left and right angles are different
Adjust the angles with adjustment feet (right and left), which are on the bottom of the projector.
Adjustment foot
EN – 12
Adjustment foot
(right and left)
Important:
• Screen on a flat wall with a 90˚ angle to the floor.
• Align projector to produce a full screen display as illustrated on page 9.
• The distance from the projector to the screen must be compatible with screen size chart on page 9. Note the distance from the screen chart.
To operate projector power ON
29
MAIN
OI
AC IN
AUTO POSITION button
MUTE
ENTER
RS-232CUSB
COMPUTER INCOMPUTER OUT
VIDEO IN
3 • 7 • 8 4
POWER
COMPUTER
VOLUME
SOURCE
VIDEO
LAMP
TEMP
S-VIDEO
VIDEO
AUDIO L
(MONO)
AUDIO R
AUTO POSITION
MENU
1. Turn on the equipment connected to the projector.
2. Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red.
• The POWER indicator blinks red for 2, 3
seconds after the power switch ON. In this time, the buttons will not work.
3. Turn the projector on by pressing the POWER button. The light source lamp starts warming up, eventu­ally turning completely on. In case the light source lamp does not come on, wait for one minute before switching power on again.
• If the main power switch to the unit is turned
off within two minutes of turning off the light source lamp, power will not be applied to the lamp for one minute when the next time the main unit power switch is turned on. When this happens, the indicator lamp will blink for one minute.
Condition
Indicator
Stand-by
When light source lamp is on
Light source lamp held off temporarily
LAMP POWER
-
Green
-
Red
Green
Red
Important:
• A darkened image may be seen right after pressing the POWER button due to warming up of this pro­jector. While warming up, no other commands can be accepted.
MUTE button
POWER MUTE
COMPUTER
3 • 7 • 8
VIDEO
MOUSE LASER
4
4
MUTE button
AUTO POSITION button
• When the lamp indicator is blinking red, the the lamp should be replaced. Replace the lamp. See pages 23 and 26.
• The picture might not be of optimum performance in extreme hot or cold conditions. (The projector is not malfunctioning.)
4. Select the desired external input source by using the COMPUTER or VIDEO button.
• The COMPUTER or VIDEO buttons do not work when MENU is displayed.
• The projector automatically selects the appropriate signal format. The selected signal format is dis­played on the screen.
• When selecting the COMPUTER input, the image may flicker. Press the $ or % button to adjust the image.
• When input signal is jittering, please adjust by $ or % button also connecting with DVD player or MUSE decoder etc.
• When supplying unstable signal like Still or Reverse play with VCR, “NO SIGNAL” may appear on the screen. In this case, you may avoid this issue by selecting the right color format like NTSC, PAL in OPTION menu.
5. Adjust the image size with the zoom ring by turn­ing it.
6. Adjust the focus with the focus ring by turning it.
focus ring
R-CLICK
MENU ENTER
AUTO POSITION
P in P EXPAND
VOLUME–+
tele
STILL
STILL button
zoom ring
wide
ENGLISH
near
far
´ EN – 13
To operate projector power ON (Continue)
Turning off the projector
7. Press the POWER button. The message “POWER OFF? YES : PRESS AGAIN” appears on the screen.
• To exit from this mode, press any button except
POWER, LASER, mouse pointer, R/L-click, STILL and VOLUME + and - buttons.
8. Press the POWER button again. The light source lamp will be turned off. Pressing the POWER button second time will shut off the light source lamp, but the exhaust fan con­tinues to operate for 120 seconds to cool down the light source lamp and LCD panels. In this time, the lamp indicator will be turned off.
9. Turn off the main power switch. When turning off the main switch, the POWER indicator turns off.
• In cases where the main power switch is acciden-
tally turned off when either the intake/exhaust fan or the power source lamp is in operation, allow the unit to cool down for 10 minutes with the power turned off. Repeat step 3 when turning on the power source lamp. If the lamp does not turn on immediately, repeat this step two or three times. Replace the lamp if it should still fail to turn on.
AUTO POSITION button
When the source is selected to COMPUTER and the image is not in the right place, set the screen to the brightest display possible, then press the AUTO POSITION button on the remote control. If the image is still not in the right place.
• Set screen to the brightest display as possible (e.g., full-screen display of the “Trash” window) before deploying the automatic adjustment func­tion.
• If the screen saver is running, turn off the screen saver before using the automatic adjustment button.
• The volume control bar will disappear about 4 seconds after releasing the volume buttons.
• The volume buttons do not work when MENU selection bar or MENU is displayed.
• The volume from the audio output terminals are not changed.
AV mute
Image and audio are temporarily erased with press­ing the MUTE button. To restore the image and audio to the normal mode, press the MUTE button again.
• To prevent the damage of the LCD, the image and audio will be restored automatically to the normal mode, 10 minutes after setting the AV mute mode.
• The audios from the audio output terminals and PC audio output terminal are not muted.
Caution:
• When you have finished using this equipment, wait 120 seconds for the exhaust fans to stop. Then turn off the main switch and unplug the power cable from the wall outlet, for safety purposes.
• After the lamp is turned off, the lamp cannot be switched on again for 60 seconds as a precaution­ary measure. It will take another 60 seconds before the lamp indicator goes off. If you wish to turn on the projector again, wait until the indicator is off then press the POWER button.
• The exhaust fan rotates faster when the tempera­ture around the projector rises.
• When the temperature around the projector becomes too high, the sign “TEMP!!” blinks red on the screen. If the temperature stays too high, the lamp will be shut off automatically .
The projector automatically shuts off when the lamp is used up in about 2000 hours. You must replace the lamp.
The sound from the speaker is mono.
• When inputting mono sound, connect to AUDIO L terminal.
• The output sound is selected by changing the setting of AUDIO MODE in the FEATURE menu. See page 16 for details.
The volume from the speaker
Press the volume + or – button to change the volume from the speaker. The volume control bar will appear on the screen.
30
EN – 14
Menu operation
IMAGE CONTRAST ± 30
BRIGHTNESS ± 30
COLOR MATRIX
USER
COLOR TEMP.
SHARPNESS ± 10
TINT ± 10
COLOR ± 10
INSTALLATION IMAGE REVERSE OFF, MIRROR, INVERT, MIRROR INVERT
KEYSTONE ± 15˚
AUTO POWER ON ON, OFF
AUTO POWER OFF
FEATURES MENU POSITION
EXPAND MODE 1 - 4
FRAME POSITION 1 - 5
AUDIO MODE
VIDEO SIGNAL
ANAMORPHIC
LANGUAGE
SIGNAL MEMORY CALL AUTO, USER1, USER2
HORIZ.POSITION 0 - 999
VERT.POSITION 0 - 999
FINE SYNC. 0 - 39
TRACKING
COMPUTER INPUT RGB, YCBCR / YPBP
HOLD AUTO
USER
MEMORIZE
DELETE
DEFAULT
1
2
3
USER
OFF
STANDARD
HIGH
LOW
USER
(Displays only when the source is selected to VIDEO) (Displays only when the source is selected to VIDEO)
(For LVP-X70U)
OFF, 5, 10, 15, 30, 60 min
1=Upper left, 2=Lower right
1 - 3
AUTO, NTSC, PAL, SECAM, 4.43NTSC, PAL-M, PAL-N, PAL-60
ON, OFF
(1 - 2 : For LVP-X50U) (For LVP-X70U only)
, English, Español, Deutsch, Français, Italiano,
* *
0 - 9999
ON OFF
USER1, USER2 USER1, USER2
*
R
RED ± 10
GREEN ± 10
BLUE ± 10
YELLOW ± 10
CYAN ± 10
MAGENTA
CONTRAST R ± 30
CONTRAST B ± 30 BRIGHTNESS R ± 30 BRIGHTNESS B ± 30
(AUTO : When the source is selected to COMPUTER)
* : Setting range is different according to the type of the signal.
BEGIN -1 - -99
END 1 - 99
CLAMP POSITION 0 - +63
CLAMP WIDTH 0 - +63 HORIZ. PIXELS 0 - 9999
VERT LINES 0 - 9999
PLL
VERT. SYNC
SHUTTER (U)
SHUTTER (L)
± 10
AUTO, 0 - 7
AUTO, ON, OFF
0 - 383 0 - 383
ENGLISH
* * * *
Basic operation
Several settings can be adjusted using Menu.
EXAMPLE: Auto power off time setting
1. Press the MENU button.
Opt
IMAGE
2. Press the $ or % button to select the INSTALLA-
TION menu.
Opt
INSTALLATION
3. Press the ENTER button (or } button).
Opt
INSTALLATION
IMAGE REVERSE
KEYSTONE 0°
AUTO POWER ON OFF
AUTO POWER OFF OFF
XGA60
XGA60
XGA60
OFF
4. Press the { or } button to select AUTO POWER
OFF.
KEYSTONE 0°
AUTO POWER ON OFF
AUTO POWER OFF OFF
5. Press the $ or % button to adjust auto power off
time.
KEYSTONE 0°
AUTO POWER ON OFF
AUTO POWER OFF 30 min
6. Exit the menu system by pressing the MENU but­ton several times.
• If the menu operation is not working, press the RESET button on the terminal board using the suit­able implement
• If the COMPUTER or VIDEO button is pressed, the MENU selection bar or MENU will disappear.
• The settings with 2 mark, you should press the ENTER button after selecting.
EN – 15
IMAGE REVERSE
INSTALLATION
OFF
KEYSTONE 0°
AUTO POWER ON OFF AUTO POWER
OFF
OFF
Opt
XGA60
MENU POSITION
FEATURE
AUDIO MODE 2
ANAMORPHIC OFF
LANGUAGE English
VIDEO SIGNAL AUTO
A
Ë
?
Opt
XGA60
EXPAND MODE 1.
FRAME POSI.
A
A
A
A
1.
1.
Menu operation (continued)
1 IMAGE
CONTRAST ........ Adjusts the picture contrast. The contrast becomes higher
as the number increases.
BRIGHTNESS .... Adjusts image brightness. The image becomes brighter as
IMAGE
the number increases.
COLOR MATRIX. ......
Adjusts color balance in each color of the image. See page
18.
COLOR TEMP... . Adjusts color temperature. See page 18.
SHARPNESS ...... Adjusts the picture sharpness. The sharpness becomes
sharper as the number increases.
TINT .................... Adjusts the color balance of the image. The color balance
of the image shifts green as the number increases and shifts to purple as the number decreases (displays only when the source is selected to VIDEO).
• When the TV50 (PAL, SECAM) signal is inputted, you cannot adjust the TINT.
COLOR ................ Adjusts the color intensity of the image (displays only when the source is selected to VIDEO).
2 INSTALLATION
IMAGE REVERSE
Use to reverse or invert the projected image. MIRROR is used for rear projection. MIRROR INVERT is effective when the projector is ceiling-mounted.
KEYSTONE ........ Adjusts keystone correction of the image. If the image has
keystone distortion, select the approximate setting. For normal use, select 0˚. (Displays LVP-X70U only).
AUTO POWER ON .....
To select whether to boot up automatically when the power is turned on external to the projector. In this case, the main power switch of the projector has to be ON. Set this when the projector is hanging on the ceiling.
• The projector is in stand-by mode when the lamp is not on. In this case, use the remote
control to turn on the lamp.
AUTO POWER OFF ..
Use to select the length of time before projector switches to stand-by when there is no input signal selected source. Select 0 min. to cancel this function.
Opt
CONTRAST
BRIGHTNESS 0
COLOR MATRIX
COLOR TEMP. STANDARD
SHARPNESS 0
TINT 0
COLOR 0
XGA60
0
USER
3 FEATURES
MENU POSITION .
EXPAND MODE Selects the mode of enlarging screen. See page 21.
FRAME POSI. .... Sets the position of sub screen. See page 21.(Displays
AUDIO MODE .......
SPLASH SCREEN . VIDEO SIGNAL . When AUTO is set, the appropriate video format is automatically selected according to the
ANAMORPHIC... Set to ON when displaying DVD discs which are recorded as squeezed images (in right and
LANGUAGE ....... Use to select the language for the projector display such as menu. ( / English / Español
EN – 16
Use to select the position where the menu is displayed, (upper left) or (lower right).
LVP-X70U only). Select 1 (COMPUTER mode) to output the sound which is inputted to audio input terminal only when the source is selected to COMPUTER. Select 2 (VIDEO mode) to output the sound which is inputted to audio input terminal only when the source is selected to VIDEO. Select 3 (PARMANENT mode) to output the sound which is inputted to audio input terminal all time. Use to display the splash screen on the screen when the power is turned ON.
input signal. If the image does not appear correctly, select the desired video format manually. Adjust the projector to the appropriate format when the projector either is not projecting normally in auto mode or is projecting PAL-M/PAL-N signals.
left direction).
/ Deutsch / Français / Italiano / )
4 SIGNAL
MEMORY CALL ........
HORIZ. POSITION ....
VERT. POSITION .....
Use to select AUTO, USER 1 or USER 2. See below. Use to adjust the horizontal position of the image. Use to adjust the vertical position of the image.
FINE SYNC. ....... Use to synchronize the projector with PC input signals so
that the image is not blurred.
TRACKING ......... Use to avoid image noise such as wide stripes.
COMPUTER INPUT ....
The unit adjusts itself automatically when connected to either DVD players with a component video output terminal (Y, CB, CR or Y, PB, PR) or equipment with HDTV signal output capabilities. In cases where the unit is connected to equipment that include an RGB output terminal and which output HDTV signals, adjust the unit to RGB mode.
HOLD .................. Adjusts the image when curving near the top.
Opt
SIGNAL
A
MEMORY CALL
U
HORIZ. POSITION 208
VERT. POSITION 22
FINE SYNC. 24
TRACKING 1056
COMPUTER INPUT RGB
R G B
R G B
HOLD AUTO
USER MEMORIZE DELETE DEFAULT
XGA60
AUTO
ENGLISH
5 SIGNAL - USER (Normally, there is no need for adjustments.)
CLAMP POSITION/
CLAMP WIDTH .........
If you use something similar, the brighter colors of the projected image may become blurred. In this case, adjust CLAMP POSITION or CLAMP WIDTH.
HORIZ.PIXELS .. Use to adjust the width of the image. The image size
grows wider as the number increases. (Adjust to the horizontal pixels of the input signal for normal setting.)
VERT.LINES ...... Use to adjust the height of the image. The image size
grows higher as the number increases. (Adjust to the
SIGNAL–USER
CLAMP POSITION
CLAMP WIDTH + 5
HORIZ. PIXELS 800
VERT. LINES 600
PLL AUTO
VERT. SYNC. AUTO
?
SHUTTER(U) 0 SHUTTER(L) 0
0
vertical lines of the input signal for normal setting.)
PLL ...................... Use to adjust the image when skewed on top. Select AUTO for normal setting.
VERT.SYNC. ...... Use to adjust the image when its motion does not run smoothly. Select AUTO for normal
setting.
SHUTTER(U) ..... Use to adjust the image when the noise etc. appears on top part of image.
SHUTTER(L) ...... Use to adjust the image when the noise etc. appears on bottom part of image.
User memory for signal setting
This projector can memorize the maximum of 2 signal menu settings.
Memorizing the setting
1. Select MEMORIZE in the SIGNAL menu, and press the ENTER button.
2. Press the $ or % button to select the memory which you wish to record (USER 1 or USER 2).
3. Press the ENTER button.
Initialite the setting which has been changed (Default)
Select RESET in the SIGNAL menu, and press the ENTER button.
When initializing, selection buttons will not work for about 2 - 18 seconds.
Select the user setting
Select MEMORY CALL in SIGNAL menu, and press the $ or % button to select the memory (USER 1 or USER 2).
Reset the recorded setting
1. Select DELETE in the SIGNAL menu, and press the ENTER button.
2. Press the $ or % button to select the memory which you wish to reset (USER 1 or USER 2).
3. Press the ENTER button. The recorded setting will be reset.
EN – 17
Picture adjustment
Adjusting the image
You can adjust the picture by using the IMAGE menu.
Opt
IMAGE
CONTRAST
BRIGHTNESS 0
COLOR MATRIX
COLOR TEMP. STANDARD
SHARPNESS 0
TINT 0
COLOR 0
XGA60
0
USER
To control the level of white-to-black in the image :
Adjust CONTRAST in IMAGE menu. Press the % button to increase the contrast and the $ button to reduce it.
To control the light level of the image :
Adjust BRIGHTNESS in IMAGE menu. Press the % button to lighten the image and the $ button to darken the image.
To adjust the detail and clarity of the image :
Adjust SHARPNESS in IMAGE menu. Press the % button to make the picture seem sharper and the $ button to make it softer.
To determine the intensity of the color :
Adjust COLOR in IMAGE menu. Press the % button to increase the amount of color in the image and the $ button to decrease it.
To adjust the red-green color balance of the image :
Adjust TINT in IMAGE menu. Press the % button to increase the amount of red in the image and the $ button to increase the amount of green in the image.
Color matrix
This feature adjusts the color balance in each color of RGB (Red, Green, Blue), and their neutral colors (yellow, cyan, magenta) by using Color correction adjustment. Use Color correct adjustment when enphasizing a specific color, or when only a certain color balance is not correctly adjusted.
1. Select COLOR MATRIX in IMAGE menu.
2. Press the ENTER button.
COLOR MATRIX
1 2 3 USER OFF
RED 0
GREEN
BLUE 0
YELLOW 0
CYAN 0
MAGENTA 0
0
When using the setting which has been already prepared
3. Press the $ or % button to select 1, 2, or 3.
• Select 1, 2 or 3 in the color matrix adjustment at your option. Selecting VIDEO input automati­cally selects 1 and selecting COMPUTER input automatically selects 3. 2 is recommended for images with high color temperature.
• Select OFF when not using Color matrix adjust­ment
When using the user setting
4. Press the $ or % button to select USER }.
5. Press the { or } button to select the desired color.
6. Press the $ or % button to adjust the color balance
of the color.
7. Repeat steps 5 and 6 for more adjusting.
8. Exit the menu system by pressing the MENU but­ton several times.
Color temperature
1. Select COLOR TEMP in IMAGE menu.
2. Press the $ or % button to select USER 2.
3. Press the ENTER button.
COLOR TEMP.-USER
CONTRAST R
CONTRAST B 0
BRIGHTNESS R 0
BRIGHTNESS B 0
4. Press the { or } button to select the desired item.
5. Press the $ or % button to adjust the item.
6. Repeat steps 4 and 5 for more adjusting.
7. Exit the menu system by pressing the MENU but­ton several times.
About color temperature
There are different kinds of white color. Color temperature is a way to show the differences. The white, which temperature is low, becomes raddish white. When the color temperature is higher, the white becomes more bluish. This projector sets this color temperature by changing the numbers of contrast blue and red. To set the color temperature high: Set the contrast B (Blue) number high, and the contrast R (Red) number low. To set the color temperature low: Set the contrast B (Blue) number low, and the contrast R (Red) number high.
0
EN – 18
Adjustment from personal computer
Although this projector sets proper signal systems automatically for the image signal from personal computers, it cannot be applied to some of personal computers. In this case, press the AUTO POSITION button. If the images are still not projected correctly, use the MENU display to adjust the projected im­ages.
Opt
SIGNAL
A
MEMORY CALL
U
HORIZ. POSITION 208
VERT. POSITION 22
FINE SYNC. 24
TRACKING 1056
COMPUTER INPUT RGB
R G B
R G B
HOLD AUTO
USER MEMORIZE DELETE DEFAULT
Image moved to right or left :
Adjust HORIZ. POSITION in SIGNAL menu. Press the % button to move the image to left. Press the $ button to move the image to right.
Image moved to up or down :
Adjust VERT. POSITION in SIGNAL menu. Press the % button to move the image to upward. Press the $ button to move the image to down.
Image flickers / Image is out of focus :
Adjust FINE SYNC. in SIGNAL menu.
XGA60
AUTO
Top part of image curves :
Change the setting of HOLD in SIGNAL menu or PLL in SIGNAL - USER menu.
HOLD ...Select ON, and adjust BEGIN or END for image which top part is the least curved.
PLL ....... Select FAST, NORMAL, or SLOW for an
image in which top part is the least curved. Select AUTO for normal setting.
Image does not move naturally :
Adjust VERT. SYNC. of the menu in SIGNAL ­USER menu. Select AUTO for normal setting. curved. Select AUTO for normal setting.
Do not change each menu setting in USER menu for normal setting.
Simple adjustment method
1. Select HORIZ. POSITION in SIGNAL menu.
2. Press the$ or % button to adjust the horizontal
start position (the left end).
3. Select TRACKING in SIGNAL menu.
4. Press the$ or % button to adjust the horizontal
end position (the right end).
5. Repeat steps 1 to 4 for fine adjustment.
6. Select VERT. POSITION in SIGNAL menu.
7. Press the$ or % button to adjust the vertical
start position (the top end).
ENGLISH
SIGNAL–USER
CLAMP POSITION
CLAMP WIDTH + 5
HORIZ. PIXELS 800
VERT. LINES 600
PLL AUTO
VERT. SYNC. AUTO
?
SHUTTER(U) 0 SHUTTER(L) 0
0
Wide stripes appear :
Adjust CLAMP POSITION or CLAMP WIDTH of each menu in SIGNAL - USER menu.
Noise etc. appears on right or left side of image :
Adjust HORIZ. PIXELS of the menu in SIGNAL ­USER menu.
Noise etc. appears on top or bottom part of image :
Adjust SHUTTER (U), SHUTTER (L) or VERT. LINES of the menu in SIGNAL - USER menu.
EN – 19
Picture adjustment (continued)
Specification of RGB signals in each computer mode of the projector
Signal mode resolution horizontal Vertical Normal mode Real mode
(H x V) frequency (kHz) frequency (Hz) (H x V) (H x V) TV60 15.73 59.94 1024 x 768 – TV50 15.63 50.00 1024 x 768 – 1080i 33.75 60.00 1024 x 576 – 720p 45.00 60.00 1024 x 576 – PC98 640 x 400 24.82 56.42 1024 x 640 640 x 400 CGA70 640 x 400 31.47 70.09 1024 x 640 640 x 400 CGA85 640 x 400 37.86 85.08 1024 x 640 640 x 400 VGA60 640 x 480 31.47 59.94 1024 x 768 640 x 480 VGA72 640 x 480 37.86 72.81 1024 x 768 640 x 480 VGA75 640 x 480 37.50 75.00 1024 x 768 640 x 480 VGA85 640 x 480 43.27 85.01 1024 x 768 640 x 480 SVGA56 800 x 600 35.16 56.25 1024 x 768 800 x 600 SVGA60 800 x 600 37.88 60.32 1024 x 768 800 x 600 SVGA72 800 x 600 48.08 72.19 1024 x 768 800 x 600 SVGA75 800 x 600 46.88 75.00 1024 x 768 800 x 600 SVGA85 800 x 600 53.67 85.06 1024 x 768 800 x 600 XGA43i 1024 x 768 35.52 86.96 1024 x 768 1024 x 768 XGA60 1024 x 768 48.36 60.00 1024 x 768 1024 x 768 XGA70 1024 x 768 56.48 70.07 1024 x 768 1024 x 768 XGA75 1024 x 768 60.02 75.03 1024 x 768 1024 x 768 XGA85 1024 x 768 68.68 85.00 1024 x 768 1024 x 768 SXGA70a 1152 x 864 63.85 70.01 1024 x 768 1024 x 768 SXGA75a 1152 x 864 67.50 75.00 1024 x 768 1024 x 768 SXGA85a 1152 x 864 77.49 85.06 1024 x 768 1024 x 768 SXGA60a 1280 x 960 60.00 60.00 1024 x 768 1024 x 768 SXGA75a 1280 x 960 75.00 75.00 1024 x 768 1024 x 768 SXGA43i 1280 x 1024 46.43 86.87 1024 x 768 1024 x 768 SXGA60 1280 x 1024 63.98 60.02 1024 x 768 1024 x 768 SXGA75 1280 x 1024 79.98 75.03 1024 x 768 1024 x 768 SXGA85 1280 x 1024 91.15 85.02 1024 x 768 1024 x 768 MAC13 640 x 480 35.00 66.67 1024 x 768 640 x 480 MAC16 832 x 624 49.72 74.55 1024 x 768 832 x 624 MAC19 1024 x 768 60.24 75.02 1024 x 768 1024 x 768 MAC21 1152 x 870 68.59 74.96 1024 x 768 1024 x 768 HP75 1024 x 768 62.94 74.92 1024 x 768 1024 x 768 HP72 1280 x 1024 78.13 72.00 1024 x 768 1024 x 768 SUN66a 1152 x 900 61.85 66.00 1024 x 768 1024 x 768 SUN76a 1152 x 900 71.81 76.63 1024 x 768 1024 x 768 SUN66 1280 x 1024 71.68 66.68 1024 x 768 1024 x 768 SUN76 1280 x 1024 81.13 76.11 1024 x 768 1024 x 768 SGI72 1280 x 1024 76.92 72.30 1024 x 768 1024 x 768 SGI76 1280 x 1024 82.00 76.00 1024 x 768 1024 x 768
IBM60 1280 x 1024 63.42 60.00 1024 x 768 1024 x 768
• When the EXPAND MODE of FEATURE menu is set to real screen display, by pressing the EXPAND button on the remote control, it will switch to the screen displaying the picture as its original size (real screen display). In the real screen display, pictures will be black-framed when picture resolution is lower than 1,024 x 768.
Important:
• Some computers may not be compatible with the projector.
• The projector's maximum resolution is 1,024 x 768 pixels. It may not display correctly for the pictures of higher resolutions than 1,024 x 768.
• The picture with a SYNC on G (Green) signal may jitter.
• The picture with a SYNC on G (Green) signal may be tinged with green.
• If the resolution and frequency of your computer are not shown on the table, change the resolution of your computer. You may find the compatible reso­lution and frequency.
• Set the COMPUTER INPUT in SIGNAL menu to RGB, when inputting the HDTV signal as RGB signal.
• Set the SIGNAL menu and USER menu as shown below, when 525p signal is inputted.
HORIZ. POSITION .......................
VERT. POSITION .........................
TRACKING ............................. 800
COMPUTER INPUT ............... YC
CLAMP POSITION .......................
CLAMP WIDTH ............................
143 54
BCR/YPBPR
+9 +3
HORIZ.PIXELS ................. 620
VERT.LINES...................... 444
VERT.SYNC. ...................... ON
EN – 20
Advanced features for presentation
Expand
By pressing the EXPAND button on the remote con­trol, you can magnify the detailed image of the picture. You can also view the screen displaying the picture as its original size (native resolution display).
Setting the Expand mode
1. Press the MENU button.
2. Press the $ or % to select the FEATURE menu.
3. Press the ENTER button.
4. Press the { or } button to select EXPAND MODE
or FRAME POSI.
5. Press the $ or % to set the EXPAND MODE or
FRAME POSI.
6. Press the MENU button twice to exit the menu sys­tem.
EXPAND MODE (For LVP-X70U)
(EXPAND MODE 1)
Normal image
EXPAND MODE (For LVP-X50U)
(EXPAND MODE 1) (EXPAND MODE 2)
(EXPAND MODE 2)
Zooming
Zooming
image
image
(EXPAND MODE 3) (EXPAND MODE 4)
Normal image
Zooming image
Native resolution display
REAL screen display
• During REAL mode, Press the $ or % buttons for fine adjustment. The { and } buttons are not working at this time.
• The expanding rate cannot be changed by press­ing either the + or - button. They are working for volume adjustment.
For LVP-X70U only
Picture in Picture (PinP)
One of the special features of this unit is the picture­in-picture (PinP) mode. PinP allows you to view differ­ent sources at the same time.
Using the PinP mode
1. Press the PinP button on the remote control.
• Pressing the PinP button repeatedly will select
on and off.
To switch Main image and Sub image
2. Press the $ or % buttons on the remote control.
To change frame position
3. Press the { or } buttons on the remote control.
FRAME POSI.
(FRAME POSI. 1~4)
12
(FRAME POSI. 5)
34
Main image
Sub image
ENGLISH
Zooming image
Real screen display
FRAME POSI. (For LVP-X70U only)
(FRAME POSI. 1~4)
12
(FRAME POSI. 5)
34
Main image
Sub image
Using the Expand mode
1. Press the EXPAND button.
• You can magnify different areas of the active pic-
ture by pressing the {, }, $, % button.
• You can change the magnification of the zoomed area by pressing the + or - button.
2. Press the EXPAND button twice on the remote con­trol. The normal screen display will appear on the screen.
• Display enlargement does not work with video input or S-video input.
• In EXPAND mode, you cannot adjust the zoom/fo­cus and the volume.
4. Press the PinP button on the remote control. The sub image will be disappear.
• Adjusting contrast, brightness, tint or color isn't available in PinP mode.
• In PinP mode, both Main image and Sub image are displayed with thir frames skipped.
• In PinP mode, the audio of the Main image is outputted.
• In PinP mode, the images may not move smoothly.
Still
How to stop the picture temporarily (still picture).
1. Press the STILL button on the remote control. The picture will be freezed temporary.
To resume picture activity.
2. Press the STILL button on the remote control again.
EN – 21
Left click
This operates in the same way as the left button on the computer.
Advanced features for presentation (continued)
Mouse remote control
By connecting to personal computer through the USB, PS/2 or ADB port, you can operate your computer with the projector remote control.
Connection
Projector + PC through USB connector
to USB
to USB port
USB cable
USB 4P
(type A)
USB 4P (type B)
• You can use the mouse remote control function with computer supported USB only. If your system is Win­dows® 98 or higher, your computer supported USB in standard. If your system is Windows® 95 or lower, please contact your dealer. If your computer is Macintosh with USB port, you can use this function.
• When the lamp is turned ON, the computer connected with the USB cable may not work correctly. In this case, restart the projector and the computer. If possible, you should disconnect the USB cable when the lamp is turned ON.
Projector + IBM PC or IBM PC compatibles
to RS-232C terminal
to mouse (PS/2) port
PS/2 adaptor
D-SUB 9PD-SUB 9PMini DIN 6P
Mini DIN 8P
Projector + Macintosh
to ADB port
to RS-232C terminal
MAC adaptor for MOUSE (option)
D-SUB 9PMini DIN 4P
RS-232C cable
D-SUB 9P
Mini DIN 8P
• Turn off PC and the projector before connecting with PS/2 port or ADB port. When connecting the PC with the projector when the personal computer is on, the remote control does not work as a mouse. In that case, restart the personal computer.
• When the projector is connected with USB terminal and RS-232C terminal at the same time, only the termi­nal which the projector recognizes first will work.
Operation
Mouse
When pressing this button, it
POWER MUTE
COMPUTER
MOUSE LASER
VIDEO
illuminates. Mouse pointer/ direction button operates as mouse pointer.
Mouse pointer
Use to move the cursor on the image, instead of the computer mouse.
Right click
This operates in the same way as the
R-CLICK
• When L/R click buttons and the mouse button are not used for 6 seconds, the mode will be changed to the normal mode automatically.
right button on the computer mouse.
EN – 22
Lamp replacement
(a)
The lamp is designed to project the image on the LCD panels. When the lamp no longer functions, replace it with a new one.
Caution:
• Do not remove the lamp immediately after turning off the lamp of the projector, you may get burned because of the high temperature of the lamp.
• For lamp replacement, press the power button to power off, then wait for 60 seconds in stand-by mode to allow the lamp and LCD panels to cool. Then turn off the main switch, unplug the power cord from the outlet, and wait one hour so that the lamp is cooled to the touch.
• Do not remove the lamp except for replacement. Careless treatment can cause injury or fire.
• Do not touch the lamp element directly. It may break and cause you to injure or burn yourself.
• Be sure not to drop the lamp lid screw into the pro­jector. Also be sure not to insert metal or any flam­mable objects, it may cause fire or electric shock. If any objects are inserted, please unplug and contact your dealer.
• Install the lamp securely, failure may cause a fire.
1. Reverse the projector gently.
2. Loosen the screws of the lamp lid on the top cover using a phillips screw­driver (+) , and remove the lid.
• Remove the lamp cover in the direction of the arrow as indicated.
3. Loosen screws (a) using a phillips screwdriver (+).
4. Pull up the handle.
5. Hold onto the projector by the handle as you pull out the lamp.
• Pull out the lamp straight
upward.
• Once the lamp has been re-
moved, do not spill liquid on it, place it near flam­mable objects or where children can touch it. Otherwise, it will cause injury or fire.
6. Insert the new lamp se­curely into the projector body in the right direc­tion.
• Make sure that the two positioning bosses (b) fit to
the lamp positioning holes before inseting the lamp.
Screw of the lamp lid
(a)
(b)
7. Put the handle back to the holding point.
• Make sure that the
handle is locked.
8. Tighten up the screws (a) using a phillips screwdriver (+).
9. Tighten up the screws of the lamp lid using a phillips screwdriver (+).
How to reset the operation time meter
Plug in the power cord, switch on the projector, and reset lamp time by pressing the $, % and POWER buttons simultaneously.
Caution:
• Do not spill liquid on the lamp or place it near flam­mable objects or where children can touch it. Oth­erwise, it could cause injury or fire.
• Be sure that the projector guide is firmly inserted between the right and left lamp guides.
Important:
• The projector will not turn on if you do not secure the lamp lid.
• You must reset the operation time meter after you replace the lamp.
• Do not reset the operation time meter unless the lamp has been replaced.
Interval of the lamp replacement
The interval of the lamp replacement about 2,000 hours of consecutive use. Replacement span may differ ac­cording to operating environment, and may be shorter than 2,000 hours. Decreases in luminescence and/or color brightness will indicate that the light source lamp needs to be replaced. When lamp operation time ex­ceeds 1,500 hours, the indicator will flash alternately between green and red (while the lamp is in operation; when the lamp is not in operation, the indicator will appear red only). When the lamp has been used for about 1,900 hours, the message “LAMP!!.” will appear on the screen for one minute. When the lamp has been used for about 2,000 hours, the projector will automati­cally shut off for the safety of the lamp and the power indicator light will be red. The projector cannot be used until the lamp has been replaced and operation timer has been reset.
Caution:
• The lamp is fragile. If broken, be careful not to cut yourself with glass fragments.
• The replacement span of the lamp depends on the environment. For replacement lamps, please con­tact your dealer.
The projector automatically shuts off af­ter about 2,000 hours, and you cannot use the projector until you replace the lamp.
EN – 23
ENGLISH
Maintenance
Caution:
Be sure to turn off the projector and unplug the power cord from the wall outlet before you perform any main­tenance on the projector.
Cleaning the air-filter
Clean the air-filter frequently. If the filter or ventilation grill become clogged with dirt or dust, the temperature inside the projector may rise and shut off the power (the TEMP indicator starts to blink red).
For side air outlet grill
1. To remove the filter cover, press the ridged area gently, push the cover in the direction of the arrow and lift.
2. Remove the air-filter from the filter cover.
3. Wash the air-filter.
• Use water or a mild
detergent diluted with water to clean the filter. Rinse the filter thoroughly and let it dry completely.
Filter cover
Filter
Cleaning the lens
Use a standard lens-cleaning brush or a piece of lens tissue dampened with lens cleaning fluid. The lens sur­face is fragile. Use only recommended, nonabrasive lens-cleaning materials. Do not touch the lens with your fingers.
4. Attach the filter to the cover.
5. Reinstall the filter cover.
Important:
• If the filter is damaged or becomes extremely dirty, contact your dealer for replacement.
• The power will not turn on if the air-filter cover is improperly installed.
Caution:
Be sure to use the projector with an air-filter. If not, dust may get inside the projector, causing a fire or a breakdown.
Cleaning the projector and the ventilation grill
Use a soft cloth to clean the projector and the ventila­tion grill. When the grill become dirty, wipe them with a soft cloth dampened with a diluted mild detergent, and then wipe them with a dry cloth. To protect the surface of the projector from fading or deteriorating:
• Do not spray insecticide on or inside the projector.
• Do not use benzine or thinner to clean it.
• Do not let rubber or plastic materials come into contact with the projector.
EN – 24
Troubleshooting
The following offers solutions to some of the common problems you may encounter. We suggest that you consult this chart before contacting your dealer.
PROBLEMS
The power is off.
No picture appears on the screen.
The image is turned off.
The image is distorted.
The image is dark. The image is
blurred.
The image remains blurred.
Red, blue or green dots are viewed on the text of image.
CAUSE
• The air inlet grill, outlet grill or air filter is clogged with dust or some objects.
POWER indicator does not light up.
• Power cord is unplugged from the outlet.
• Power cord is disconnected from the projector.
• The main switch is turned off.
• The lamp lid is open.
POWER indicator blinks red.
• The projector has been turned on again too soon after having been turned off.
• When the power switch was turned off while the fan was running, during or after lamp operation.
• The room temperature is too high. (Does the LAMP indicator show an unusual condition?) Lamp is no longer working.
POWER indicator blinks between red and green.
• The filter cover is not closed.
• When the LAMP indicator or the TEMP indicator is either on or blinking, the main unit requires repairs.
Lens is covered by lens cap.
• When the LAMP indicator or the TEMP indicator is either on or blinking, the main unit requires repairs. The equipment connected to this projector is not
• turned on. Hookup is not made correctly with other equipment.
• The input source is not selected correctly.
• The air inlet grill, outlet grill or air filter is clogged with dust or some objects.
(In this case, the TEMP indicator does not light up.) The projector is not at a right angle to the screen.
Brightness, tint and color are not adjusted correctly.
• The projecting distance is beyond the focused area.
• Lens is dirty.
Screen size exceeds screen size specifications.
Brightness and contrast are not adjusted correctly.
• FINE adjustment is not made correctly.
• Tracking is not adjusted. The projector is not at a right angle to the screen.
When you see the stationary image for a long time, it may remain on the screen if you change the
• image. It is not a breakdown. The blurred image will disappear in a few minutes.
It is normal.
• Insert the power cord into the projector.
• Close the lamp lid.
• Turn the power switch on and off several times.
• Confirm the hookup.
• Adjust tracking.
POSSIBLE SOLUTIONS
Remove the object.
Plug the power cord into the outlet.
Turn the main switch on.
Wait for the lighting sequence.
Refer to "Indicators" on page 26.
Replace the lamp with a new one.
Close the cover correctly. Contact your dealer.
Take the lens cap off. Replace the lamp with a new one.
Turn on the connected equipment.
Select the correct source according to the equip­ment connected to this projector.
Remove the object and turn off the main power switch. After about 10 minutes, Turn the pro­jector on.
Adjust the angle of the projector to make a right angle to the screen. See page 12.
Adjust brightness, tint and color correctly. Adjust the projecting distance. See page 9.
Clean lens.
Reduce screen size to within 40" to 300".
Adjust brightness, contrast. Make FINE adjustment.
Adjust the angle of the projector to make a right angle to the screen. See page 12.
ENGLISH
The image is dis­torted on the screen and noise is heard.
No sound is heard.
Nothing is displayed on the PC monitor.
Warm air comes out of the exhaust vents.
Adjustments cannot be made.
The cable for connection with other equipment
• is not plugged securely into the terminal.
The projector is installed too close to other
• equipment.
Volume is not turned up.
• Connection to other equipment is not made correctly.
• The PC monitor is not turned on.
This is typical of the LCD projector.
The operation is incorrectly made due to noise or
• interference.
Plug the connecting cable securely into the
• terminal. See pages 10-11.
Install the projector far away from other equipment.
Turn up the volume.
• Check connections. See pages 10-11.
Turn on the monitor.
Press the reset button on the Terminal board.
• See page 15.
EN – 25
Indicators
The projector has three LED Indicators which shows the working condition of the projector.
The following offers solutions to possible problems. If a problem persists, turn the projector off and consult your dealer.
AUTO POSITION
POWER indicator
POWER
MUTE
COMPUTER
LAMP indicator
TEMP indicator
Normal condition
POWER LAMP TEMP
Steady
red
Steady
green
Steady
green
Blinking
green
Steady
green
OffOff
Off
Off
CONDITION Notes
Stand-by
Lamp stand-by (about for 1 minute) The power button cannot be used to switch
The POWER is ON. (Normal condition)
Abnormal condition
POWER LAMP TEMP
Steady
green
Steady
red
Steady
green
Off
Blinking
Blinking
CONDITION POSSIBLE SOLUTIONS
Unusual temperature
• The ventilation slits or air filter is clogged with
red
• The fan has stopped due to an impediment.
• The room temperature is too high.
red
• The filter is dirty.
dust or debris.
LAMP
TEMP
VOLUME
SOURCE
VIDEO
MENU
ENTER
ON and OFF
• Remove the object from the ventilation slits.
Pull out the power plug andremove the object. If you cannot, consult your dealer.
• Relocate the projector to a cooler place.
• Clean the filter.
Steady
green
Steady
red
Steady
red
Blinking
green/red
Blinking
green/red
EN – 26
Blinking
green/red
Blinking
red
Steady
red
Off
Steady
Blinking Blinking
Off
Off
Off
Off
Steady
or or
Lamp duration warning. (Lightning duration total about 1, 500 hours.When the POWER is ON.)
Lamp duration warning. (Lightning duration total
Replace the lamp. Exchange with a new lamp if the same problem recurs.
about 1, 500 hours.When the POWER is OFF.)
Lamp duration warning. (Lightning duration total about 2,000 hours.)
The lamp or filter cover is not closed. Close the cover correctly.
Abnormal. Contact your dealer.
Specifications
Type
Model
Rated power supply
Rated input
LCD panels
Colors
Projection lens
Light source lamp
Picture size
PC compatibility
Video compatibility
Audio output
Speaker
S-video input
LCD projector
LVP-X50U | LVP-X70U
AC100V ~ 240V, 50 / 60Hz
2.3 A
0.9-inch LCD panel: 3 pieces (for R, G, B)
Pixels 1,024 × 768 = 786,432 pixels
Total 2,359,296 pixels
Active pixel rate: 99.99 % or more (each panel)
16,770,000 colors
F 1.7~2.0 f = 33.2 mm ~ 43.1 mm
150 W UHP (2, 000 Hours)
40 inch ~ 300 inch (aspect ratio 4:3)
Resolution : 640 x 400 - 1024 x 768 + Compressed 1280 x 1024
Sync on Green available
NTSC / NTSC 4.43 / PAL (including PAL-M, N) / SECAM, PAL-60
DVD (Component) / HDTV (1080i) / 720p / (525p)
1 W mono
6 cm square type (8 1W) Luminance signal: Vp-p=1.0V 75 (negative sync.)
ENGLISH
Chroma signal: Vp-p=0.286V 75 (burst signal)
Video input
Audio inputs
Analog RGB input
(mini D-SUB 15P)
Control connector
Outside dimensions
Weight
Length of power cord
Temperature, humidity
Vp-p=1.0V 75 (negative sync.) 350 mVrms, 10kΩ or more RGB: Vp-p=0.7V 75 (negative sync.)
YCBCR: Y: Vp-p=1.0V (negative sync.) CBCR: Vp-p=0.7V
HD/CS : TTL level (positive or negative)
VD : TTL level (positive or negative)
Serial (DIN 8 pin female connector) RS-232C standards
PS/2 (Mouse function), USB terminal for Mouse
242 mm × 79 mm × 294 mm (9.5 inch × 3.1 inch × 11.6 inch) (width × height × depth)
Approx. 3.2 kg (7 lbs)
2.9m (9.5 feet)
+41°F (+5°C) ~ +95°F (+35°C), 30~90%
Legs and lens are not included.
(performance guarantee)
Kensington Lock
This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System. Refer to the information that came with the Kensington System for instructions on how to use it to secure the projector. Please contact to Kensington Technology Group as shown below.
Kensington Technology Group 2855 Campus Drive San Mateo, CA 94403, U.S.A.
Phone : (650)572-2700 Fax : (650)572-9675
EN – 27
12
6 8
5
3
Specifications (continued)
Connectors
PC analog RGB input
Use to input video signals (analog
RGB) of a personal computer.
(Pin assignment of Mini D-SUB 15P jack)
PIN NO. SPEC PIN NO. SPEC
1 R(RED)/CR 9– 2 3
G(GREEN)/Y B(BLUE)/CB
10 GROUND
11 GROUND 4 GROUND 12 – 5 GROUND 13 HD/CS 6 GROUND 14 VD 7 GROUND 15 – 8 GROUND
Dimensional drawings (mm)
11 15
15
147.5 31.5
f26
RS-232C input
Use to control the projector with the personal computer, or control the personal computer with remote con­trol. Use the provided RS-232C cable (Mini
DIN 8P-D-SUB 9P) for the connection.
PIN NO. NAME I/O
1 TXD IN 2 RTS IN 3 DTR IN 4 GND – 5 CTS/5V IN / OUT 6 DCD/CLOCK OUT 7 RXD OUT 8 RI/DATA OUT
f26
242 7
155
f72.5
79
89.5
47.5
(10.5)
What’s included in the box
2 AC power cord 246C383-10
246C383-20 1 AV(Audio/Video) cable 246C381-10 1 S-Video cable 859C687-01 1 RGB cable for PC 246C382-10 1 RS-232C cable 246C366-10 1 PS/2 adapter 246C367-10
265 11
f18
122.3
294 26.5
1 USB cable 859C686-01 1 Remote control 939P795-50 (LVP-X50U)
939P795-10 (LVP-X70U) 1 User manual 871D288-10 1 Quick reference card 857B023-10 2 Battery for remote – 1 Carrying case 772P032-10
Replacement part (Option / Not included in the box)
Spare Mercury lamp 499B022-10
EN – 28
(VLT-X70LP)
Loading...