Mitsubishi MSZ-A09RV- E1, MSZ-A12RV- E1, MUZ-A09RV- E1, MUZ-A12RV- E1 Service Manual

SPLIT-TYPE, HEAT PUMP AIR CONDITIONERS

SERVICE MANUAL

Wireless type
Models

1999

No. OB230

MSZ-A09RV -

MSZ-A12RV -

(WH)●

(WH)●

MUZ-A09RV ­MUZ-A12RV -

CONTENTS

1. TECHINICAL CHANGES ··································2

2. PART NAMES AND FUNCTIONS······················4

3. SPECIFICATION·················································6

4. NOISE CRITERIA CURVES·······························8

5. OUTLINES AND DIMENSIONS·························9

6. WIRING DIAGRAM ··········································10

7. REFRIGERANT SYSTEM DIAGRAM··············12

8. PERFORMANCE CURVES······························13

9. MICROPROCESSOR CONTROL ····················23

10. SERVICE FUNCTIONS·····································38

11. TROUBLESHOOTING ······································40

12. DISASSEMBLY INSTRUCTIONS·····················57

13. PARTS LIST······················································61

14. OPTIONAL PARTS···········································65

E1E1

E1E1

1 TECHNICAL CHANGES

Lubricant

Refrigerant

New refrigerant

R-410A

HFC-32: HFC-125 (50%:50%)

Pseudo-azeotropic refrigerant

Not included

A1/A1

72.6

-51.4

1.557
64

Non combustible

0

1730

From liquid phase in cylinder

Possible

Incompatible oil

Non
Non

Previous refrigerant

R-22

R-22 (100%)

Single refrigerant

Included

A1

86.5

-40.8

0.94

44.4

Non combustible

0.055
1700

Gas phase

Possible

Compatible oil

Light yellow

Non

Refrigerant
Composition (Ratio)
Refrigerant handling
Chlorine
Safety group (ASHRAE)
Molecular weight
Boiling point (:)
Steam pressure [25:](Mpa)
Saturated steam density [25:](Kg/K)
Combustibility
ODP w1
GWP w2
Refrigerant charge method
Additional charge on leakage
Kind
Color
Smell

New Specification Current Specification

w1:Ozone Destruction Parameter : based on CFC-11
w2 :Global Warmth Parameter : based on CO

2

The incompatible lubricant easily separates from refrigerant
and is in the upper layer inside the suction muffler.
Raising position of the oil back hole enables to back the
lubricant of the upper layer to the compressor.

Since refrigerant and lubricant are compatible each, lubricant
backs to the compressor through the lower position oil back
hole.

Compressor

Suction muffler

Oil back hole

Lubricant

Refrigerant

Compressor

Suction muffler

Oil back hole

Lubricant /Refrigerant

Compressor

INFORMATION FOR THE AIR CONDITIONER WITH R-410A REFRIGERANT

• This room air conditioner adopts R-410A of HFC refrigerant which never destroys the ozone layer.
Pay attention following points.

1 As R-410A working pressure is 1.6 times higher than that of R-22 of previous refrigerant, dedicated tools and piping are

required.

2 R-410A is more affected by water and contaminations than R-22. Keep R-410Aaway from water and contaminations during

storage and while installing.

3 Use clean dedicated piping materiales for R-410A only which are strong enough against R-410Apressure. Never use any

current pipes designed for R-22.

4 Composition change may occur in R-410A since it is a mixed refrigerant. When charging, charge liquid refrigerant to prevent

composition change.

NOTE : The unit of pressure has been changed to MPa on the international system of units(SI unit system).

The conversion factor is: 1(MPa • G) =10.2(kgf/ff• G)

2

-30 -20 -10 0 10 20

30

40 50 60

-0.5

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

4.0

(MPa.G)

R-410A
R-22

Conversion chart of refrigerant temperature and pressure

Saturated liquid pressure

(;)

NOTE : The unit of pressure has been changed to MPa on the

R-410A tools

Can R-22 tools be used?

Gas leak detector

R-410A pressures beyonds the measurement range of R-22
gauges. Port diameters have been changed to prevent other kinds of
refrigerant from being charged into the units.

Hose material and cap size have been changed to improve the pressure
resistance.

Dedicated for HFC refrigerant.
1/4 and 3/8 wrenches can be used for both R-22 and R-410A units.

Description

Clamp bar hole has been enlarged to reinforce the spring strength in the tool.
Provided for flaring work (to be used with R-22 flare tool).

Provided to prevent the back flow of oil. This adapter enables you to use
vacuum pumps.
It is difficult to measure R-410A with a charging cylinder because the
refrigerant bubbles due to high pressure and high-speed vaporization

No

No

No

Yes
Yes

Newly required

Newly required

Newly required

Gauge manifold

Charge hose

Torque wrench
Flare tool
Flare gauge

Vacuum pump
adapter

Electronic scale for
refrigerant charging

No : Not Substitutable for R-410A Yes : Substitutable for R-410A

Wall
thickness

Outside diameter

Pipe

mm inch
For liquid
For gas

6.35

9.52

1/4
3/8

0.8 mm

0.8 mm

Heat resisting foam plastic
Specific gravity 0.045 Thickness 8 mm

Insulation material

international system of units(SI unit system).

The conversion factor is: 1(MPa • G) =10.2(kgf/ff• G)

1.Tools dedicated for the air conditioner with R-410A refrigerant

The following tools are required for R-410A refrigerant. Some R-22 tools can be substituted for R-410Atools.
The diameter of the service port on the outdoor unit operation valve has been changed to prevent improper refrigerant
charging. Cap size has also been changed from 7/16 UNF with 20 threads to 1/2 UNF with 20 threads.

2.Refrigerant piping

1 Specifications

Use the refrigerant pipes that meet the following specifications.

• Use a copper pipe or a coppor-alloy seamless pipe with a thickness of 0.7 mm or less, as the pressure resistance is in

2 Flaring work and flare nut

sufficient.

Flaring work for R-410A pipes differs from that for the existing refrigerant pipes.
for details of flaring work, refer to Installation manual “6-1 FLARING WORK”.

3

2 Optional extension pipe for R-410A

3m
5m

7m
10m
12m

([6.35/[9.52)
([6.35/[9.52)
([6.35/[9.52)
([6.35/[9.52)
([6.35/[9.52)

MAC-A00PI
MAC-A01PI
MAC-A02PI
MAC-A03PI
MAC-A04PI

3.Refrigerant oil

Apply the special refrigeration oil (accessories) to the flare and the union seat surfaces.

4.Air purge

Use the vacuum pump for air purging for the purpose of environmental protection.

5.Additional charge

For additional charging, charge the refrigerant from liquid phase of the gas cylinder. If the refrigerant is charged from the
gas phase, composition chang may occur in the refrigerant inside the cylinder and the outdoor unit. However, charging the
liquid refrigerant all at once may cause the compressor to be locked. Thus, charge the refrigerant slowly.

Gas cylinder

2

PART NAMES AND FUNCTIONS

MSZ-A09RV­MSZ-A12RV-

INDOOR UNIT

Air cleaning
filter(white bellows
type)

Deodorizing filter
(gray sponge type)

Air filter

Outdoor unit

Valve

Refrigerant gas cylinder
for R-410A with siphon

Electronic scale for refrigerant charging

E1
E1

Grille

Air inlet

to Breaker

Power supply cord

Liquid

Front panel

Vertical vanes

Operation section

(When the grille is open)

Emergency operation switch

Remote control
receiving section

Horizontal vane

Remote
controller

Display section

Operation Indicator

Receiving section

4

Signal transmitting section

Operation display section

OPERATE /STOP

(ON /OFF)button

OPERATION SELECT button

FAN SPEED CONTROL button

ON-TIMER button

CLOCK SET button

HR. button

MIN. button

(TIME SET button)

TEMPERATURE buttons

VANE CONTROL button

OFF-TIMER button

RESET button

ON/OFF TOO

WARM

TOO

COOL

HR. MIN.

CLOCK

RESET

CLOCK

MODE

FAN

VANE

START

STOP

ECONO COOL button

ECONO COOL

I FEEL

COOL DRY HEAT

6 00

1 1 00

AM

PM

SWING

SWING button

MUZ-A09RV­MUZ-A12RV-

E1
E1

OUTDOOR UNIT

Air inlet

Piping

Drain hose

Air outlet

Drain outlet

MSZ-A09RV­MSZ-A12RV-

E1
E1

REMOTE CONTROLLER

5

3

Indoor model

Function

Power supply

Capacity
Air flow(Hi)
Dehumidification
Power outlet
Running current
Power input
Auxiliary heater
Power factor
Starting current
Fan motor current
Model
Winding
resistance(at20:)
Dimensions WOHOD
Weight
Air direction
Sound level (Hi)
Fan speed (Hi)
Fan speed regulator
RT11(at25:)
Thermistor RT12(at25:)
RT13(at25:)
Outdoor model
Outdoor air flow
Compressor motor current
Fan motor current

Model
Output
Winding
resistance(at20:)
Model
Winding
resistance(at20:)
Dimensions WOHOD
Weight
Sound level
Fan speed
Fan speed regulator
Refrigerant filling
capacity(R-410A)
Refrigerating oil (Model)

RT61(at100:)

Thermistor RT62(at0:)
RT64(at50:)



kW

K /h

R/h

A
A

W

A(kW)

%

A
A

"



mm

kg

dB

rpm

k"
k"
k"

K /h

A
A

W

"





"



mm

kg

dB

rpm

kg

cc
k"
k"
k"



MSZ-A09RV -

E1

Single phase

220-240V,50Hz

10

—

99

4.55 - 4.17

0.17

RA4V19-BA

WHT-BLK 292.4

BLK-RED 324.6

850O278O191

10

5

3
10
10
10

MUZ-A09RV -

E1

0.27-0.25

SNB-092FBA

700

U-V 0.93 U-W 0.93

V-W 0.93

RA6V28-CA

WHT-BLK 197

BLK-RED 315 YLW-BLK 13

710(+69)o540o255

34

2

1.10

450 (NEO22)

13.4

32.6
17

Cooling

2.6 (0.9-3.3)
516

1.2

3.67-3.37

800 (250-1180)

36

920

1440

6.9

3.25

45

670

Heating

3.6 (0.9-4.8)
540

—

4.55-4.17

990 (250-1650)

35

950

1530

7.4

3.64

47

700

MSZ-A12RV -

E1

Single phase

220-240V,50Hz

10

—
99

7.25 - 6.65

0.19

RA4V19-BA
WHT-BLK 292.4
BLK-RED 324.6

850O278O191

10

5

3
10
10
10

MUZ-A12RV -

E1

0.27-0.25

SNB-092FBA

900

U-V 0.93 U-W 0.93

V-W 0.93

RA6V28-CA

WHT-BLK 197

BLK-RED 315 YLW-BLK 13

710(+69)o540o255

34

2

1.10

450 (NEO22)

13.4

32.6
17

Cooling

3.4 (0.9-3.8)
588

1.6

5.60 - 5.13

1220 (250 - 1580)

39

1020

1440

7.4

2.79

46

670

Heating

`4.8 (0.9-6.1)

642

—

7.25 - 6.65

1580 (250 - 2050)

39

1100

1530

8.1

3.04

48

700

Electrical

data

Fan

motor

Special

remarks

Compressor

Electrical
data

Fan

motor

Special

remarks

Coefficient of performance(C.O.P)

Capacity

Capacity

SPECIFICATION

NOTE : Test conditions.

Cooling : Indoor DB27: WB19:
Heating : Indoor DB 20: WB -:

Outdoor DB35: WB24:
Ondoor DB 7: WB 6:

6

1.5+ 440V

MP24GA 12V 300"

ERZV10D471

S201DH1Y

4P

JM1aN-ZTMP-DC12V

93.5:5A 250V
136:i3: 2A

250V 3.15A

500+ 450V

1.8+ 440V
RR-18

250V 2A

13A 1.0mH

EM43240
50m" 5W

100" 20W

4P

PS21101-AL / PS21204-A

G4U-1-E
G4U-1-E

LB6 250V AC

PMA10001

G4A-1A-P-PS

INDOOR UNIT

OUTDOOR UNIT

Item

Model

Model

Item

Indoor fan capacitor
Vane motor
Varistor (NR11)
Semiconductor relay
Terminal block
Relay (compressor) (52C)
Terminal block thermal Fuse
Indoor fan motor thermal fuse
Fuse (F11)

Smoothing capacitor (C61,C62)
Outdoor fan capacitor (C65)
Current transformer (CT61)
Fuse (F801, F901)
Reactor (L64)
Noise filter
Current detecting resistor (R61, 62, 64)
Current limiting resistor (R65)
Terminal block
Intelligent power module
Relay (X61)
Relay (X62)
Reversing valve coil
Power factor controll module
Rush current limiting relay

MSZ-A09RV
MSZ-A12RV

MUZ-A09RV
MUZ-A12RV

Specifications and rating conditions of main electric parts

7

90

80

70

60

50

40

30

20

10

63 125 250 500 1000 2000 4000 8000

APPROXIMATE
TERESHOLD OF
HEARING FOR
CONTINUOUS
NOISE

NC-60

NC-50

NC-40

NC-30

NC-20

NC-70

OCTAVE BAND SOUND PRESSURE LEVEL, dB re 0.002 MICRO BAR

BAND CENTER FREQUENCIES, Hz

Test conditions.

Cooling : DB27: WB19:
Heating : DB20: WB -:

MSZ-A09RV- E1

HEATING

NOTCH

35

COOLING 36

SPL(dB(A)) LINE

90

80

70

60

50

40

30

20

10

63 125 250 500 1000 2000 4000 8000

APPROXIMATE
TERESHOLD OF
HEARING FOR
CONTINUOUS
NOISE

NC-60

NC-50

NC-40

NC-30

NC-20

NC-70

OCTAVE BAND SOUND PRESSURE LEVEL, dB re 0.002 MICRO BAR

BAND CENTER FREQUENCIES, Hz

Test conditions.

Cooling :DB35

:

WB24

:

Heating :DB 7

:

WB 6

:

MUZ-A09RV- E1

HEATING

NOTCH

47

COOLING 45

SPL(dB(A)) LINE

90

80

70

60

50

40

30

20

10

63 125 250 500 1000 2000 4000 8000

APPROXIMATE
TERESHOLD OF
HEARING FOR
CONTINUOUS
NOISE

NC-60

NC-50

NC-40

NC-30

NC-20

NC-70

OCTAVE BAND SOUND PRESSURE LEVEL, dB re 0.002 MICRO BAR

BAND CENTER FREQUENCIES, Hz

Test conditions.

Cooling : DB27

:

WB19

:

Heating : DB20

:

WB -

:

MSZ-A12RV- E1

HEATING
COOLING

NOTCH

39

SPL(dB(A)) LINE

90

80

70

60

50

40

30

20

10

63 125 250 500 1000 2000 4000 8000

APPROXIMATE
TERESHOLD OF
HEARING FOR
CONTINUOUS
NOISE

NC-60

NC-50

NC-40

NC-30

NC-20

NC-70

OCTAVE BAND SOUND PRESSURE LEVEL, dB re 0.002 MICRO BAR

BAND CENTER FREQUENCIES, Hz

Test conditions.

Cooling :DB35

:

WB24

:

Heating :DB 7

:

WB 6

:

MUZ-A12RV- E1

HEATING

NOTCH

48

COOLING 46

SPL(dB(A)) LINE

4

NOISE CRITERIA CURVES

8

116.581.5

818

278

850

16562956

or more

100

41

2.5

42

271 4.5

231.5

82

169

326 326

5

189

56

160

17.5

Air in

Air out

Insulation [28

Drain hose [16
(Connected part O.D)

Installation plate

Wall hole [65

Indoor unit

Installation plate

Power supply cord
Lead to right 1.0m
Lead to left 0.3m

Wireless remote controller

Liquid line [6.35-0.5m
Gas line [9.52-0.43m
Insulation [37 O.D

[21 I.D

78

67

7

{

OUTLINES AND DIMENSIONS5

Liquid refrigerant pipe joint
Refrigerant pipe (flared) [6.35

Service panel

Gas refrigerant pipe joint
Refrigerant pipe (flared) [9.52

Service port

Bolt pitch for installation

Handle

Air out

Air in

Drainage holes [28

4 holes 10o21

18

500
710

265

105

69

138

20

40

If both sides or back
side is vacant. only
to be free 50 cm in
front of a unit

Air in

265

REQUIRED SPACE

If a front side or both sides
is vacant. an upper side of
a unit has only to be vacant 10cm.

Drainage holes [28

127

32.4

92

367

Drainage holes [28

33

32.5

255

285

320

155

90

43-

35-

540

270

10

35cm or more

50cm or more

10cm or more

10cm or more

10cm

or m

ore

MSZ-A09RV­MSZ-A12RV-

INDOOR UNIT

E1
E1

MUZ-A09RV­MUZ-A12RV-

OUTDOOR UNIT

E1
E1

9

6 WIRING DIAGRAM

MSZ-A09RV- MSZ-A12RV- MODELS WIRING DIAGRAM

E1E1

INDOOR UNIT

TO OUTDOOR
UNIT
CONNECTING

12V

220-240V~

POWER
SUPPLY
CORD
~/N 220-240V
50Hz

PE

CIRCUIT BREAKER

TB

L

BRN

BRN

3

2

WHT

N

BLU

BLU

GRN/YLW

RED

F12

GRN/YLW

GREEN SIGN
MONITOR
P.C.BOARD

11

BLU
BLU

1
2

BLU

CN

CN

151

1J1

CN201

3
2
1

LD101T

10

MV1

MV2

3

4

ELECTRONIC CONTROL P.C. BOARD

5

POWER MONITOR,
RECEIVER
P.C.BOARD

52C

HIC1

TRANS

F11

NR11

SR141

REMOTE
CONTROLLER

C11

4
3
2

1

CN112

CN

121

1
2
3

CN211

CN
111

RT13
RT12

BLK

3

GRY
YLW
BRN
WHT
RED

1
2
3

MF

4
5
6

RT11

SYMBOL
C11
F11
F12
HIC1
MF
MV1
MV2

NOTE:1. About the outdoor side electric wiring refer to the outdoor unit electric wiring diagram for servicing.

INDOOR FAN CAPACITOR
FUSE (3.15A)
THERMAL FUSE (93:)
DC/DC CONVERTER
INDOOR FAN MOTOR
VANE MOTOR (HORIZONTAL)
VANE MOTOR (VERTICAL)

2. Use copper conductors only. (For field wiring)

3. Symbols below indicate.
/: Terminal block, : Connector

NAME

SYMBOL
NR11

RT11

RT12

RT13

NAME
VARISTOR
ROOM TEMPERATURE
THERMISTOR
INDOOR COIL
THERMISTOR (MAIN)
INDOOR COIL
THERMISTOR (SUB)

SYMBOL
SR141
TB
52C

NAME
SOLID STATE RELAY
TERMINAL BLOCK
CONTACTOR

10

MUZ-A09RV- MUZ-A12RV- MODELS WIRING DIAGRAM

E1E1

OUTDOOR UNIT

220-240V ~

SYMBOL
CT61
C61,C62
C65
DSA61
F801
F901
IC950
IPM
LEV
L61

NOISE FILTER P.C BOARD

R65

X64

LDNF2

CT61

LD-E

GRN

DSA61

NR61

TB1

3

12V

FROM INDOOR UNIT
CONNECTING

RED

WHT

2

BLU

N

TAB61

L61

TAB62

BLU

GRN/YLW

NAME
CURRENT TRANSFORMER
SMOOTHING CAPACITOR
OUTDOOR FAN CAPACITOR
SURGE ABSORBER
FUSE (2A)
FUSE (2A)
DC/DC CONVERTER

INTELLIGENT POWER MODULE

EXPANSION VALVE COIL
CMC COIL

BLU

TAB72

SSR61

CN913

21S4

L63

LDNF1

WHT

RELAY

TAB71

P.C
BOARD

F901

C65

12

ORG

SYMBOL
L63
L64
MC
MF61
NR61
PFC
RT61
RT62
RT64
R61,62

TAB68

TAB69

CN912

CN

X61

X62

WHT
BLU

CN914

3
2

911

1

654321

LD62
LD61

4

CN779CN778

4

3
2

CN726

1

CN771

ELECTRONIC

R61

R62

C61

C62

IC950

TRANS

CONTROL

BLK

RED

WHT

YLW

5

MF61

COIL
REACTOR
COMPRESSOR
OUTDOOR FAN MOTOR (INNER FUSE)
VARISTOR
POWER FACTOR CONTROL MODULE
DISCHARGE TEMPERATURE THERMIST OR
DEFROST THERMISTOR
FIN TEMPERATURE THERMIST OR
CURRENT-DETECTING RESISTOR

P.C BOARD

CN601

231

NAME

PFC

+
+

F801

R64

6
5
4
3
2

CN641

1

-

1
2

CN642

SYMBOL
R64
R65
SSR61
TB1, TB2
X61, X62
X64

21S4

6

LEV

+

U

V
W

RT64

CN724

TAB75

TAB76

LD65

LD66

LD67

V

GRY

TB2

BLK

1
2

BLK

WHT

RED

3

RED

~

~

P
N

IPM

RT61

RT62

MC

NAME
CURRENT-DETECTING RESISTOR
CURRENT-LIMITING RESISTOR
SOLID STATE RELAY
TERMINAL BLOCK
RELAY
RELAY
REVERSING VALVE COIL
(COOLING TURN ON)

GRY

BLK

21

WHT

W

L64

BLK

U

NOTE:1. About the indoor side electric wiring refer to the indoor unit electric wiring diagram for servicing.

2.Use copper conductors only. (For field wiring)

3. Symbols below indicate.
/: Terminal block, : Connector

11

7

Refrigerant Piping
Max. length
A

Height difference should be within
5m regardless of which unit,
indoor or outdoor position is high.

w Max. Height

difference 8m

Indoor
unit

Outdoor unit

Indoor
heat
exchanger

Outdoor
heat
exchanger

Distributor

Flared connection

Room temperature
thermistor
RT11

Indoor coil
thermistor
RT13(sub)

Defrost
thermistor
RT62

Discharge
thermistor
RT61

Flared connection

Stop valve

Stop valve
(with service port)

Capillary tube

Capillary tube
(2 pcs)

Refrigerant flow in cooling

Compressor

Accumulator

Maffler

Muffler

Reversing valve

Refrigerant flow in heating

Refrigerant pipe [9.52
(Option)

Refrigerant pipe [6.35
(Option)

Indoor coil
thermistor
RT12(main)

Expansion
valve

[3.0o[2.0o200

[3.0o[2.0o300

REFRIGERANT SYSTEM DIAGRAM

MSZ-A09RV ­MSZ-A12RV -

Unit : mm

E1
E1

MUZ-A09RV ­MUZ-A12RV -

E1
E1

INDOOR UNIT

MAX. REFRIGERANT PIPING LENGTH

Additional piping

Model

MSZ-A09RV­MSZ-A12RV-

E1

E1

Max. length :mm

A

12

OUTDOOR UNIT

Piping size O.D : mm

Gas Liquid Indoor unit Outdoor unit

9.52 6.35 0.43 0

Length of connecting pipe : m

MAX. HEIGHT DIFFERENCE

ADDITIONAL REFRIGERANT CHARGE (R-410A:g)

Model

MSZ-A09RV­MSZ-A12RV-

Outdoor unit precharged

E1

E1

For additional charging, charge the refrigerant from liquid phase of the gas cylinder.
If the refrigerant inside the cylinder and the outdoor unit.
However, charging the liquid refrigerant all at once may cause the compressor to be locked.
Thus, charge the refrigerant slowly.

1100

7m

0

Refrigerant piping length (one way)

30

12

9m8m

60

11m10m

12090

Calculation : Xg=30g /m✕ (A-7)m

12m

150

PERFORMANCE CURVES8

The standard data contained in these specifications apply only to the operation of the air conditioner under normal conditions.

Since operating conditions vary according to the areas where these units are installed. The following information has been
provided to clarify the operating characteristics of the air conditioner under the conditions indicated by the performance curve.

(1) GUARANTEED VOLTAGE

Rated voltage : ±10% (198 ~ 242V ),50Hz

(2) AIR FLOW

Air flow should be set at MAX.

(3) MAIN READINGS

(1) Indoor intake air wet-bulb temperature ::WB
(2) Indoor discharge air wet-bulb temperature ::WB
(3) Outdoor intake air dry-bulb temperature ::DB
(4) Total input :W
(5) Indoor intake air dry-bulb temperature ::DB
(6) Outdoor intake air wet-bulb temperature ::WB
(7) Total input :W

Indoor air wet-bulb temperature difference on the left side of the chart on next page shows the difference between the
indoor intake air wet-bulb temperature and the indoor discharge air wet-bulb temperature for your reference at service.

E1

Cooling

}

Heating

}

How to measure the indoor air wet-bulb temperature difference

1. Attach at least 2 sets of wet-and dry-bulb thermometers to the indoor air intake as shown in the figure, and at least 2 sets
of wet-and dry-bulb thermometers to the indoor air outlet. The thermometers must be attached to the position where air
speed is high.

2. Attach at least 2 sets of dry-bulb thermometers to the outdoor air intake.
Cover the thermometers to prevent direct rays of the sun.

3. Check that the air filter is cleaned.

4. Open windows and doors of room.

5. Press the EMERGENCY OPERATION switch once (twice) to start the EMERGENCY COOL (HEAT) MODE.

6. When system stabilizes after more than 15 minutes, measure temperature and take an average temperature.

7. 10 minutes later, measure temperature again and check that the temperature does not change.

INDOOR UNIT

OUTDOOR UNIT

13

7.4

6.9

6.3

5.8

5.3

4.8

MSZ-A09RV- E1

8.5

7.9

7.3

6.7

6.1

5.5

MSZ-A12RV- E1

0 50 100 150(Hz)

0.0

0.5

1.0

1.5

Correction of Cooling capacity

Capacity correction factors

The operational frequency of compressor

0 50 100 150(Hz)

0.0

0.5

1.0

1.5

Correction of Cooling capacity

Capacity correction factors

The operational frequency of compressor

Cooling capacity

MUZ-A09RV -

MUZ-A12RV -

E1

MUZ-A09RV -

E1

Correction of total input

2.0

1.5

1.0

0.5

Capacity correction factors

0 50 100 150(Hz)

The operational frequency of compressor

E1

MUZ-A12RV -

E1

Correction of total input

2.0

1.5

1.0

0.5

Capacity correction factors

0 50 100 150(Hz)

The operational frequency of compressor

14

27.1

25.1

23.0

20.9

18.8

16.7

14.6

12.5

30.4

28.1

25.8

23.4

21.1

18.7

16.4

14.1

MSZ-A12RV- E1

MSZ-A09RV- E1

0 50 100 150(Hz)

0.0

0.5

1.0

1.5

Correction of Heating capacity

Capacity correction factors

The operational frequency of compressor

0 50 100 150(Hz)

0.0

0.5

1.0

1.5

Correction of Heating capacity

Capacity correction factors

The operational frequency of compressor

Heating capacity

Correction of total input

Capacity correction factors

The operational frequency of compressor

0 50 100 150(Hz)

0.5

1.0

1.5

Correction of total input

Capacity correction factors

The operational frequency of compressor

0 50 100 150(Hz)

0.5

1.0

1.5

NOTE:The above curves are for the heating operation without any frost.

MUZ-A09RV -

MUZ-A12RV -

E1

E1

MUZ-A09RV -

MUZ-A12RV -

E1

E1

15

OUTDOOR LOW PRESSURE AND OUTDOOR UNIT CURRENT

(MPa • G)

(kgf/F • G)

(reference)



18 32

62Hz



15 20

50

25
60

30
70(%)

35(:)

0.6

0.7

0.8

0.9

1.0

1.1

62Hz

6

7

8

9

10

11

12

1.2

220V

240V

15 20

50

25
60

30

70(%)

35(:)

3

4

5

6

7

83Hz

32

18

15 20

50

25
6030 70(%)

35(:)

1

2

3

4

5

32

18

220V

240V

53Hz

How to operate with fixed operational frequency of the compressor.

1. Press the EMERGENCY OPERATION switch on the front of the indoor unit , and select either the COOLmode or the
HEAT mode before starting to operate the air conditioner.

2. The compressor starts up.
The operational frequency of the compressor is 83Hz in the COOL mode and 58Hz in the HEAT mode.

3. The fan speed of the indoor unit is Hi.

4. This operation continues for 30minutes.

5. In order to release this operation, press the EMERGENCY OPERATION switch again, press any button on the remote

controller.

NOTE : The unit of pressure has been changed to MPa on the international system of units(SI unit system).

The conversion factor is: 1(MPa • G) =10.2(kgf/ff• G)

COOL operation

1 Both indoor and outdoor unit are under the same temperature/humidity condition.

Dry-bulb temperature

20
25
30

2 Air flow should be set at Hi.

Relative humidity(%)

50
60
70

3 Operational frequency : 83Hz

(reference)
(kgf/F • G)

13

12

11

10

9

8

Outdoor low pressure

7

Outdoor low pressure

MUZ-A09RV -

(MPa • G)

1.3

1.2

1.1

1.0

0.9

0.8

0.7
18 32

15 20

50

25
60

Ambient temperature(:)
Ambient humidity(%)

MUZ-A12RV -

Ambient temperature(:)
Ambient humidity(%)

E1

62Hz

62Hz

MUZ-A09RV -

E1

Outdoor unit current (A)

30







70(%)

35(:)

Ambient temperature(:)
Ambient humidity(%)

E1

MUZ-A12RV -

E1

Outdoor unit current (A)

Ambient temperature(:)
Ambient humidity(%)

16

6.0

5.5

5.0

4.5

4.0

3.5

3.0
2

5 10152025

240V

220V

58Hz

HEAT operation

58Hz

220V

240V

6.0

5.5

5.0

4.5

4.0

3.5

3.0
2

510152025

Condition Indoor : Dry bulb temperature 20.0:

Wet bulb temperature 14.5:

Outdoor : Dry bulb temperature 2 7 15 20.0:

Wet bulb temperature 1 6 12 14.5:

MUZ-A09RV -

Outdoor unit current (A)

Ambient temperature(:)

E1

MUZ-A12RV -

E1

Outdoor unit current (A)

Ambient temperature(:)

17

PERFORMANCE DATA
COOL operation

MUZ-A09RV -

CAPACITY : 2.6 kW INPUT : 800 W SHF : 0.74

INDOOR INDOOR

DB(:) WB(:) Q SHC SHF INPUT Q SHC SHF INPUT Q SHC SHF INPUT Q SHC SHF INPUT

21
21
22
22
22
23
23
23
24
24
24
24
25
25
25
25
26
26
26
26
26
27
27
27
27
27
28
28
28
28
28
29
29
29
29
29
30
30
30
30
30
31
31
31
31
31
32
32
32
32
32

E1

OUTDOOR DB(:)

21 25 27 30

18

3.06 1.71 0.56 640 2.93 1.64 0.56 672 2.81 1.57 0.56 704 2.70 1.51 0.56 736

20

3.19 1.40 0.44 672 3.06 1.34 0.44 712 2.96 1.30 0.44 728 2.86 1.26 0.44 760

18

3.06 1.83 0.60 640 2.93 1.76 0.60 672 2.81 1.68 0.60 704 2.70 1.62 0.60 736

20

3.19 1.53 0.48 672 3.06 1.47 0.48 712 2.96 1.42 0.48 728 2.86 1.37 0.48 760

22

3.32 1.19 0.36 696 3.20 1.15 0.36 740 3.12 1.12 0.36 760 2.99 1.08 0.36 792

18

3.06 1.96 0.64 640 2.93 1.87 0.64 672 2.81 1.80 0.64 704 2.70 1.73 0.64 736

20

3.19 1.66 0.52 672 3.06 1.59 0.52 712 2.96 1.54 0.52 728 2.86 1.49 0.52 760

22

3.32 1.33 0.40 696 3.20 1.28 0.40 740 3.12 1.25 0.40 760 2.99 1.20 0.40 792

18

3.06 2.08 0.68 640 2.93 1.99 0.68 672 2.81 1.91 0.68 704 2.70 1.84 0.68 736

20

3.19 1.78 0.56 672 3.06 1.71 0.56 712 2.96 1.66 0.56 728 2.86 1.60 0.56 760

22

3.32 1.46 0.44 696 3.20 1.41 0.44 740 3.12 1.37 0.44 760 2.99 1.32 0.44 792

24

3.48 1.11 0.32 728 3.35 1.07 0.32 768 3.28 1.05 0.32 792 3.17 1.02 0.32 832

18

3.06 2.20 0.72 640 2.93 2.11 0.72 672 2.81 2.02 0.72 704 2.70 1.95 0.72 736

20

3.19 1.91 0.60 672 3.06 1.83 0.60 712 2.96 1.78 0.60 728 2.86 1.72 0.60 760

22

3.32 1.59 0.48 696 3.20 1.54 0.48 740 3.12 1.50 0.48 760 2.99 1.44 0.48 792

24

3.48 1.25 0.36 728 3.35 1.21 0.36 768 3.28 1.18 0.36 792 3.17 1.14 0.36 832

18

3.06 2.32 0.76 640 2.93 2.22 0.76 672 2.81 2.13 0.76 704 2.70 2.06 0.76 736

20

3.19 2.04 0.64 672 3.06 1.96 0.64 712 2.96 1.90 0.64 728 2.86 1.83 0.64 760

22

3.32 1.72 0.52 696 3.20 1.66 0.52 740 3.12 1.62 0.52 760 2.99 1.55 0.52 792

24

3.48 1.39 0.40 728 3.35 1.34 0.40 768 3.28 1.31 0.40 792 3.17 1.27 0.40 832

26

3.59 1.00 0.28 768 3.48 0.98 0.28 808 3.43 0.96 0.28 832 3.33 0.93 0.28 856

18

3.06 2.44 0.80 640 2.93 2.34 0.80 672 2.81 2.25 0.80 704 2.70 2.16 0.80 736

20

3.19 2.17 0.68 672 3.06 2.08 0.68 712 2.96 2.02 0.68 728 2.86 1.94 0.68 760

22

3.32 1.86 0.56 696 3.20 1.79 0.56 740 3.12 1.75 0.56 760 2.99 1.67 0.56 792

24

3.48 1.53 0.44 728 3.35 1.48 0.44 768 3.28 1.44 0.44 792 3.17 1.40 0.44 832

26

3.59 1.15 0.32 768 3.48 1.11 0.32 808 3.43 1.10 0.32 832 3.33 1.06 0.32 856

18

3.06 2.57 0.84 640 2.93 2.46 0.84 672 2.81 2.36 0.84 704 2.70 2.27 0.84 736

20

3.19 2.29 0.72 672 3.06 2.20 0.72 712 2.96 2.13 0.72 728 2.86 2.06 0.72 760

22

3.32 1.99 0.60 696 3.20 1.92 0.60 740 3.12 1.87 0.60 760 2.99 1.79 0.60 792

24

3.48 1.67 0.48 728 3.35 1.61 0.48 768 3.28 1.57 0.48 792 3.17 1.52 0.48 832

26

3.59 1.29 0.36 768 3.48 1.25 0.36 808 3.43 1.24 0.36 832 3.33 1.20 0.36 856

18

3.06 2.69 0.88 640 2.93 2.57 0.88 672 2.81 2.47 0.88 704 2.70 2.38 0.88 736

20

3.19 2.42 0.76 672 3.06 2.32 0.76 712 2.96 2.25 0.76 728 2.86 2.17 0.76 760

22

3.32 2.12 0.64 696 3.20 2.05 0.64 740 3.12 2.00 0.64 760 2.99 1.91 0.64 792

24

3.48 1.81 0.52 728 3.35 1.74 0.52 768 3.28 1.70 0.52 792 3.17 1.65 0.52 832

26

3.59 1.44 0.40 768 3.48 1.39 0.40 808 3.43 1.37 0.40 832 3.33 1.33 0.40 856

18

3.06 2.81 0.92 640 2.93 2.69 0.92 672 2.81 2.58 0.92 704 2.70 2.49 0.92 736

20

3.19 2.55 0.80 672 3.06 2.44 0.80 712 2.96 2.37 0.80 728 2.86 2.29 0.80 760

22

3.32 2.25 0.68 696 3.20 2.17 0.68 740 3.12 2.12 0.68 760 2.99 2.03 0.68 792

24

3.48 1.95 0.56 728 3.35 1.88 0.56 768 3.28 1.83 0.56 792 3.17 1.78 0.56 832

26

3.59 1.58 0.44 768 3.48 1.53 0.44 808 3.43 1.51 0.44 832 3.33 1.46 0.44 856

18

3.06 2.93 0.96 640 2.93 2.81 0.96 672 2.81 2.70 0.96 704 2.70 2.60 0.96 736

20

3.19 2.68 0.84 672 3.06 2.57 0.84 712 2.96 2.49 0.84 728 2.86 2.40 0.84 760

22

3.32 2.39 0.72 696 3.20 2.30 0.72 740 3.12 2.25 0.72 760 2.99 2.15 0.72 792

24

3.48 2.09 0.60 728 3.35 2.01 0.60 768 3.28 1.97 0.60 792 3.17 1.90 0.60 832

26

3.59 1.72 0.48 768 3.48 1.67 0.48 808 3.43 1.65 0.48 832 3.33 1.60 0.48 856

18

3.06 3.06 1.00 640 2.93 2.93 1.00 672 2.81 2.81 1.00 704 2.70 2.70 1.00 736

20

3.19 2.80 0.88 672 3.06 2.69 0.88 712 2.96 2.61 0.88 728 2.86 2.52 0.88 760

22

3.32 2.52 0.76 696 3.20 2.43 0.76 740 3.12 2.37 0.76 760 2.99 2.27 0.76 792

24

3.48 2.23 0.64 728 3.35 2.15 0.64 768 3.28 2.10 0.64 792 3.17 2.03 0.64 832

26

3.59 1.87 0.52 768 3.48 1.81 0.52 808 3.43 1.78 0.52 832 3.33 1.73 0.52 856

18

OUTDOOR DB(:)

INDOOR INDOOR

35 40 43

DB(:) WB(:) Q SHC SHF INPUT Q SHC SHF INPUT Q SHC SHF INPUT

21 18 2.55 1.43 0.56 784 2.34 1.31 0.56 832 2.25 1.26 0.56 848
21 20 2.68 1.18 0.44 816 2.50 1.10 0.44 856 2.41 1.06 0.44 880
22 18 2.55 1.53 0.60 784 2.34 1.40 0.60 832 2.25 1.35 0.60 848
22 20 2.68 1.29 0.48 816 2.50 1.20 0.48 856 2.41 1.15 0.48 880
22 22 2.83 1.02 0.36 848 2.65 0.95 0.36 896 2.56 0.92 0.36 912
23 18 2.55 1.63 0.64 784 2.34 1.50 0.64 832 2.25 1.44 0.64 848
23 20 2.68 1.39 0.52 816 2.50 1.30 0.52 856 2.41 1.25 0.52 880
23 22 2.83 1.13 0.40 848 2.65 1.06 0.40 896 2.56 1.02 0.40 912
24 18 2.55 1.73 0.68 784 2.34 1.59 0.68 832 2.25 1.53 0.68 848
24 20 2.68 1.50 0.56 816 2.50 1.40 0.56 856 2.41 1.35 0.56 880
24 22 2.83 1.25 0.44 848 2.65 1.17 0.44 896 2.56 1.13 0.44 912
24 24 2.99 0.96 0.32 880 2.81 0.90 0.32 920 2.73 0.87 0.32 940
25 18 2.55 1.83 0.72 784 2.34 1.68 0.72 832 2.25 1.62 0.72 848
25 20 2.68 1.61 0.60 816 2.50 1.50 0.60 856 2.41 1.44 0.60 880
25 22 2.83 1.36 0.48 848 2.65 1.27 0.48 896 2.56 1.23 0.48 912
25 24 2.99 1.08 0.36 880 2.81 1.01 0.36 920 2.73 0.98 0.36 940
26 18 2.55 1.94 0.76 784 2.34 1.78 0.76 832 2.25 1.71 0.76 848
26 20 2.68 1.71 0.64 816 2.50 1.60 0.64 856 2.41 1.54 0.64 880
26 22 2.83 1.47 0.52 848 2.65 1.38 0.52 896 2.56 1.33 0.52 912
26 24 2.99 1.20 0.40 880 2.81 1.12 0.40 920 2.73 1.09 0.40 940
26 26 3.15 0.88 0.28 912 2.96 0.83 0.28 952 2.87 0.80 0.28 972
27 18 2.55 2.04 0.80 784 2.34 1.87 0.80 832 2.25 1.80 0.80 848
27 20 2.68 1.82 0.68 816 2.50 1.70 0.68 856 2.41 1.64 0.68 880
27 22 2.83 1.59 0.56 848 2.65 1.49 0.56 896 2.56 1.43 0.56 912
27 24 2.99 1.32 0.44 880 2.81 1.24 0.44 920 2.73 1.20 0.44 940
27 26 3.15 1.01 0.32 912 2.96 0.95 0.32 952 2.87 0.92 0.32 972
28 18 2.55 2.14 0.84 784 2.34 1.97 0.84 832 2.25 1.89 0.84 848
28 20 2.68 1.93 0.72 816 2.50 1.80 0.72 856 2.41 1.73 0.72 880
28 22 2.83 1.70 0.60 848 2.65 1.59 0.60 896 2.56 1.54 0.60 912
28 24 2.99 1.44 0.48 880 2.81 1.35 0.48 920 2.73 1.31 0.48 940
28 26 3.15 1.13 0.36 912 2.96 1.07 0.36 952 2.87 1.03 0.36 972
29 18 2.55 2.24 0.88 784 2.34 2.06 0.88 832 2.25 1.98 0.88 848
29 20 2.68 2.04 0.76 816 2.50 1.90 0.76 856 2.41 1.83 0.76 880
29 22 2.83 1.81 0.64 848 2.65 1.70 0.64 896 2.56 1.64 0.64 912
29 24 2.99 1.55 0.52 880 2.81 1.46 0.52 920 2.73 1.42 0.52 940
29 26 3.15 1.26 0.40 912 2.96 1.19 0.40 952 2.87 1.15 0.40 972
30 18 2.55 2.34 0.92 784 2.34 2.15 0.92 832 2.25 2.07 0.92 848
30 20 2.68 2.14 0.80 816 2.50 2.00 0.80 856 2.41 1.92 0.80 880
30 22 2.83 1.93 0.68 848 2.65 1.80 0.68 896 2.56 1.74 0.68 912
30 24 2.99 1.67 0.56 880 2.81 1.57 0.56 920 2.73 1.53 0.56 940
30 26 3.15 1.38 0.44 912 2.96 1.30 0.44 952 2.87 1.26 0.44 972
31 18 2.55 2.45 0.96 784 2.34 2.25 0.96 832 2.25 2.16 0.96 848
31 20 2.68 2.25 0.84 816 2.50 2.10 0.84 856 2.41 2.02 0.84 880
31 22 2.83 2.04 0.72 848 2.65 1.91 0.72 896 2.56 1.84 0.72 912
31 24 2.99 1.79 0.60 880 2.81 1.68 0.60 920 2.73 1.64 0.60 940
31 26 3.15 1.51 0.48 912 2.96 1.42 0.48 952 2.87 1.38 0.48 972
32 18 2.55 2.55 1.00 784 2.34 2.34 1.00 832 2.25 2.25 1.00 848
32 20 2.68 2.36 0.88 816 2.50 2.20 0.88 856 2.41 2.12 0.88 880
32 22 2.83 2.15 0.76 848 2.65 2.02 0.76 896 2.56 1.95 0.76 912
32 24 2.99 1.91 0.64 880 2.81 1.80 0.64 920 2.73 1.75 0.64 940
32 26 3.15 1.64 0.52 912 2.96 1.54 0.52 952 2.87 1.49 0.52 972

CAPACITY : 2.6 kW INPUT : 800 W SHF : 0.74

PERFORMANCE DATA
COOL operation

MUZ-A09RV -

E1

19

PERFORMANCE DATA
COOL operation

MUZ-A12RV -

CAPACITY : 3.4 kW INPUT : 1220 W SHF : 0.69

INDOOR INDOOR

DB(:) WB(:) Q SHC SHF INPUT Q SHC SHF INPUT Q SHC SHF INPUT Q SHC SHF INPUT

21 18 4.00 2.04 0.51 976 3.83 1.95 0.51 1025 3.67 1.87 0.51 1074 3.54 1.80 0.51 1122
21 20 4.17 1.62 0.39 1025 4.00 1.56 0.39 1086 3.88 1.51 0.39 1110 3.74 1.46 0.39 1159
22 18 4.00 2.20 0.55 976 3.83 2.10 0.55 1025 3.67 2.02 0.55 1074 3.54 1.94 0.55 1122
22 20 4.17 1.79 0.43 1025 4.00 1.72 0.43 1086 3.88 1.67 0.43 1110 3.74 1.61 0.43 1159
22 22 4.34 1.34 0.31 1061 4.18 1.30 0.31 1129 4.08 1.26 0.31 1159 3.91 1.21 0.31 1208
23 18 4.00 2.36 0.59 976 3.83 2.26 0.59 1025 3.67 2.17 0.59 1074 3.54 2.09 0.59 1122
23 20 4.17 1.96 0.47 1025 4.00 1.88 0.47 1086 3.88 1.82 0.47 1110 3.74 1.76 0.47 1159
23 22 4.34 1.52 0.35 1061 4.18 1.46 0.35 1129 4.08 1.43 0.35 1159 3.91 1.37 0.35 1208
24 18 4.00 2.52 0.63 976 3.83 2.41 0.63 1025 3.67 2.31 0.63 1074 3.54 2.23 0.63 1122
24 20 4.17 2.12 0.51 1025 4.00 2.04 0.51 1086 3.88 1.98 0.51 1110 3.74 1.91 0.51 1159
24 22 4.34 1.69 0.39 1061 4.18 1.63 0.39 1129 4.08 1.59 0.39 1159 3.91 1.52 0.39 1208
24 24 4.56 1.23 0.27 1110 4.39 1.18 0.27 1171 4.28 1.16 0.27 1208 4.15 1.12 0.27 1269
25 18 4.00 2.68 0.67 976 3.83 2.56 0.67 1025 3.67 2.46 0.67 1074 3.54 2.37 0.67 1122
25 20 4.17 2.29 0.55 1025 4.00 2.20 0.55 1086 3.88 2.13 0.55 1110 3.74 2.06 0.55 1159
25 22 4.34 1.86 0.43 1061 4.18 1.80 0.43 1129 4.08 1.75 0.43 1159 3.91 1.68 0.43 1208
25 24 4.56 1.41 0.31 1110 4.39 1.36 0.31 1171 4.28 1.33 0.31 1208 4.15 1.29 0.31 1269
26 18 4.00 2.84 0.71 976 3.83 2.72 0.71 1025 3.67 2.61 0.71 1074 3.54 2.51 0.71 1122
26 20 4.17 2.46 0.59 1025 4.00 2.36 0.59 1086 3.88 2.29 0.59 1110 3.74 2.21 0.59 1159
26 22 4.34 2.04 0.47 1061 4.18 1.97 0.47 1129 4.08 1.92 0.47 1159 3.91 1.84 0.47 1208
26 24 4.56 1.59 0.35 1110 4.39 1.54 0.35 1171 4.28 1.50 0.35 1208 4.15 1.45 0.35 1269
26 26 4.69 1.08 0.23 1171 4.56 1.05 0.23 1232 4.49 1.03 0.23 1269 4.35 1.00 0.23 1305
27 18 4.00 3.00 0.75 976 3.83 2.87 0.75 1025 3.67 2.75 0.75 1074 3.54 2.65 0.75 1122
27 20 4.17 2.62 0.63 1025 4.00 2.52 0.63 1086 3.88 2.44 0.63 1110 3.74 2.36 0.63 1159
27 22 4.34 2.21 0.51 1061 4.18 2.13 0.51 1129 4.08 2.08 0.51 1159 3.91 1.99 0.51 1208
27 24 4.56 1.78 0.39 1110 4.39 1.71 0.39 1171 4.28 1.67 0.39 1208 4.15 1.62 0.39 1269
27 26 4.69 1.27 0.27 1171 4.56 1.23 0.27 1232 4.49 1.21 0.27 1269 4.35 1.18 0.27 1305
28 18 4.00 3.16 0.79 976 3.83 3.02 0.79 1025 3.67 2.90 0.79 1074 3.54 2.79 0.79 1122
28 20 4.17 2.79 0.67 1025 4.00 2.68 0.67 1086 3.88 2.60 0.67 1110 3.74 2.51 0.67 1159
28 22 4.34 2.38 0.55 1061 4.18 2.30 0.55 1129 4.08 2.24 0.55 1159 3.91 2.15 0.55 1208
28 24 4.56 1.96 0.43 1110 4.39 1.89 0.43 1171 4.28 1.84 0.43 1208 4.15 1.78 0.43 1269
28 26 4.69 1.45 0.31 1171 4.56 1.41 0.31 1232 4.49 1.39 0.31 1269 4.35 1.35 0.31 1305
29 18 4.00 3.32 0.83 976 3.83 3.17 0.83 1025 3.67 3.05 0.83 1074 3.54 2.93 0.83 1122
29 20 4.17 2.96 0.71 1025 4.00 2.84 0.71 1086 3.88 2.75 0.71 1110 3.74 2.66 0.71 1159
29 22 4.34 2.56 0.59 1061 4.18 2.47 0.59 1129 4.08 2.41 0.59 1159 3.91 2.31 0.59 1208
29 24 4.56 2.14 0.47 1110 4.39 2.06 0.47 1171 4.28 2.01 0.47 1208 4.15 1.95 0.47 1269
29 26 4.69 1.64 0.35 1171 4.56 1.59 0.35 1232 4.49 1.57 0.35 1269 4.35 1.52 0.35 1305
30 18 4.00 3.48 0.87 976 3.83 3.33 0.87 1025 3.67 3.19 0.87 1074 3.54 3.08 0.87 1122
30 20 4.17 3.12 0.75 1025 4.00 3.00 0.75 1086 3.88 2.91 0.75 1110 3.74 2.81 0.75 1159
30 22 4.34 2.73 0.63 1061 4.18 2.63 0.63 1129 4.08 2.57 0.63 1159 3.91 2.46 0.63 1208
30 24 4.56 2.32 0.51 1110 4.39 2.24 0.51 1171 4.28 2.18 0.51 1208 4.15 2.12 0.51 1269
30 26 4.69 1.83 0.39 1171 4.56 1.78 0.39 1232 4.49 1.75 0.39 1269 4.35 1.70 0.39 1305
31 18 4.00 3.64 0.91 976 3.83 3.48 0.91 1025 3.67 3.34 0.91 1074 3.54 3.22 0.91 1122
31 20 4.17 3.29 0.79 1025 4.00 3.16 0.79 1086 3.88 3.06 0.79 1110 3.74 2.95 0.79 1159
31 22 4.34 2.90 0.67 1061 4.18 2.80 0.67 1129 4.08 2.73 0.67 1159 3.91 2.62 0.67 1208
31 24 4.56 2.51 0.55 1110 4.39 2.41 0.55 1171 4.28 2.36 0.55 1208 4.15 2.28 0.55 1269
31 26 4.69 2.02 0.43 1171 4.56 1.96 0.43 1232 4.49 1.93 0.43 1269 4.35 1.87 0.43 1305
32 18 4.00 3.80 0.95 976 3.83 3.63 0.95 1025 3.67 3.49 0.95 1074 3.54 3.36 0.95 1122
32 20 4.17 3.46 0.83 1025 4.00 3.32 0.83 1086 3.88 3.22 0.83 1110 3.74 3.10 0.83 1159
32 22 4.34 3.08 0.71 1061 4.18 2.97 0.71 1129 4.08 2.90 0.71 1159 3.91 2.78 0.71 1208
32 24 4.56 2.69 0.59 1110 4.39 2.59 0.59 1171 4.28 2.53 0.59 1208 4.15 2.45 0.59 1269
32 26 4.69 2.21 0.47 1171 4.56 2.14 0.47 1232 4.49 2.11 0.47 1269 4.35 2.05 0.47 1305

E1

OUTDOOR DB(:)

21 25 27 30

20