Mitsubishi electric MSH-GA60VB, MUH-GA60VB User Manual [ru]

SPLIT-TYPE AIR CONDITIONERS

INDOOR UNIT

MS-GE50VB MSH-GE50VB

Русский

Türkçe

Svenska

Dansk

Português

Ελληνικά

Italiano

Español

Nederlands

Français

Deutsch

English

OPERATING INSTRUCTIONS

For user

• To use this unit correctly and safely, be sure to read these operating in­structions before use.

ИНСТРУКЦИИ ПО ЭКСПЛУАТАЦИИ

Для пользователя

•

В це лях прав иль н ой и без о пас ной экс п луатаци и да нного

устройства обязательно перед его использованием прочтите
настоящее руководство по эксплуатации.

ÇALIŞTIRMA TALİMATLARI

Kullanıcı için

• Bu üniteyi doğru ve güvenli bir biçimde kullanmak için, kullanmadan
önce bu işletim talimatlarını okuduğunuzdan emin olun.

BRUKSANVISNING För användaren

• Läs bruksanvisningen innan enheten tas i bruk så att den används sä­kert och på rätt sätt.

BETJENINGSVEJLEDNING Til kunden

• Læs denne betjeningsvejledningen før brug, så enheden bruges korrekt
og sikkert.

INSTRUÇÕES DE OPERAÇÃO Para o utilizador

• Para utilizar esta unidade correctamente e com segurança, certifique­se de que lê estas instruções de operação antes da utilização.

O∆ΗΓΙΕΣ ΛΕΙΤOΥΡΓΙΑΣ

Για τoρήστη

•

Για να ρησιµoπoιήσετε αυτή τη µoνάδα σωστά και µε ασφάλεια, εαι­ωθείτε oτι έετε διαάσει αυτ τ εγειρίδι δηγιών πριν απ τη

ρή-

ση.

LIBRETTO D’ISTRUZIONI Per gli utenti

• Per utilizzare correttamente ed in tutta sicurezza questo apparecchio,
leggere il presente libretto d’istruzioni prima dell’uso.

MANUAL DE INSTRUCCIONES

Para los clientes

• Para utilizar esta unidad de forma correcta y segura, lea previamente
estas instrucciones de funcionamiento.

BEDIENINGSINSTRUCTIES Voor de klant

• Om dit apparaat correct en veilig te kunnen gebruiken moet u deze be­dieningsinstructies voor gebruik eerst doorlezen.

NOTICE D’UTILISATION

A l’attention des clients

• Pour avoir la certitude d’utiliser cet appareil correctement et en toute
sécurité, veuillez lire cette notice d’instructions avant de mettre le clima

-

tiseur sous tension.

BEDIENUNGSANLEITUNG For den Anwender

• Für einen sicheren und ordnungsgemäßen Gebrauch des Geräts unbe­dingt diese Bedienungsanleitung vor der Inbetriebnahme durchlesen.

En-1

• OPERATING INSTRUCTIONS •

WARNING

Do not connect the power cord to an intermediate point,
use an extension cord, or connect multiple devices to a
single AC outlet.

• This may cause overheating, fire, or electric shock.

Make sure the power plug is free of dirt and insert it se­curely into the outlet.

• A dirty plug may cause fire or electric shock.

Do not bundle, pull, damage, or modify the power cord, and
do not apply heat or place heavy objects on it.

• This may cause fire or electric shock.

Do not turn the breaker OFF/ON or disconnect/connect the
power plug during operation.

• This may create sparks, which can cause fire.

• After the indoor unit is switched OFF with the remote con­troller, make sure to turn the breaker OFF or disconnect the
power plug.

Do not expose your body directly to cool air for a prolonged
length of time.

• This could be detrimental to your health.

The unit should not be installed, relocated, disassembled,
altered, or repaired by the user.

• An improperly handled air conditioner may cause fire, electric
shock, injury, or water leakage.

Do not insert your finger, a stick, or other objects into the
air inlet or outlet.

• This may cause injury, since the fan inside rotates at high
speeds during operation.

• Since rotating parts and parts which could cause an electric shock are used
in this product, be sure to read these “Safety Precautions” before use.

• Since the cautionary items shown here are important for safety, be sure to
observe them.

• After reading this manual, keep it together with the installation manual in a
handy place for easy reference.

Marks and their meanings

WARNING :

Incorrect handling could cause serious hazard, such as
death, serious injury, etc. with a high probability.

CAUTION :

Incorrect handling could cause serious hazard depending
on the conditions.

In case of an abnormal condition (such as a burning smell),
stop the air conditioner and disconnect the power plug or
turn the breaker OFF.

• A continued operation in the abnormal state may cause a
malfunction, fire, or electric shock. In this case, consult your
dealer.

When the air conditioner does not cool or heat, there is
a possibility of refrigerant leakage. In this case, consult
your dealer. If a repair involves recharging the unit with
refrigerant, ask the service technician for details.

• The refrigerant used in the air conditioner is safe. Normally,
it does not leak. However, if refrigerant leaks and comes in
contact with a heat source such as a fan heater, kerosene
heater, or cooking stove, it will create a harmful gas.

CAUTION

Do not touch the air inlet or the aluminum fins of the
indoor/outdoor unit.

• This may cause injury.

Do not use insecticides or flammable sprays on the unit.

• This may cause a fire or deformation of the unit.

Do not expose pets or houseplants to direct airflow.

• This may cause injury to the pets or plants.

Do not place other electric appliances or furniture under
the indoor/outdoor unit.

• Water may drip down from the unit, which may cause damage
or malfunction.

Do not leave the unit on a damaged installation stand.

• The unit may fall and cause injury.

Meanings of symbols used in this manual

: Be sure not to do.

: Be sure to follow the instruction.

: Never insert your finger or stick, etc.

:

Never step onto the indoor/outdoor unit and do not put anything on them.

: Danger of electric shock. Be careful.

: Be sure to disconnect the power supply plug from the power outlet.

: Be sure to shut off the power.

SAFETY PRECAUTIONS

CONTENTS

 SAFETY PRECAUTIONS 1
 DISPOSAL 2
 NAME OF EACH PART 3
 PREPARATION BEFORE OPERATION 3
 SELECTING OPERATION MODES 4
 FAN SPEED AND AIRFLOW DIRECTION ADJUSTMENT 5
 ECONO COOL OPERATION 6
 LONG OPERATION 6
 TIMER OPERATION (ON/OFF TIMER) 6
 CLEANING 7
 WHEN YOU THINK THAT TROUBLE HAS OCCURRED 8
 WHEN THE AIR CONDITIONER IS NOT GOING TO BE USED FOR A LONG TIME 9
 INSTALLATION PLACE AND ELECTRICAL WORK 9
 SPECIFICATIONS 9

En-2

CAUTION

Do not step on an unstable bench to operate or clean the
unit.

• This may cause injury if you fall down.

Do not pull the power cord.

• This may cause a portion of the core wire to break, which may
cause overheating or fire.

Do not charge or disassemble the batteries, and do not
throw them into a fire.

• This may cause the batteries to leak, or cause a fire or explo­sion.

Do not operate the unit for a long time at high humidity (80%
RH or more), such as with a door or window left open.

• The water condensation in the air conditioner may drip down,
wetting or damaging the furniture.

Do not use the unit for special purposes, such as storing
food, raising animals, growing plants, or preserving preci­sion devices or art objects.

• This may cause deterioration of quality, or harm to animals
and plants.

Do not expose combustion appliances to direct airflow.

• This may cause incomplete combustion.

Before cleaning the unit, switch it OFF and disconnect the
power plug or turn the breaker OFF.

• This may cause injury, since the fan inside rotates at high
speeds during operation.

When the unit will be unused for a long time, disconnect the
power plug or turn the breaker OFF.

• The unit may accumulate dirt, which may cause overheating
or fire.

Replace all batteries of the remote controller with new ones
of the same type.

• Using an old battery together with a new one may cause
overheating, leakage, or explosion.

If the battery fluid comes in contact with your skin or clothes,
wash them thoroughly with clean water.

• If the battery fluid comes in contact with your eyes, wash them
thoroughly with clean water and immediately seek medical
attention.

Ensure that the area is well-ventilated when the unit is oper­ated together with a combustion appliance.

• Inadequate ventilation may cause oxygen starvation.

Turn the breaker OFF when you hear thunder and there is a
possibility of a lightning strike.

• The unit may be damaged if lightning strikes.

After the air conditioner is used for several seasons, per­form inspection and maintenance in addition to normal
cleaning.

• Dirt or dust in the unit may create an unpleasant odor, con­tribute to growth of fungi, such as mold, or clog the drain pas­sage, and cause water to leak from the indoor unit. Consult
your dealer for inspection and maintenance, which require
specialized knowledge and skills.

WARNING

Consult your dealer for installing the air conditioner.

• It should not be installed by the user since installation requires
specialized knowledge and skills. An improperly installed air
conditioner may cause water leakage, fire, or electric shock.

Provide a dedicated power supply for the air conditioner.

• A non-dedicated power supply may cause overheating or
fire.

Do not install the unit where flammable gas could leak.

• If gas leaks and accumulates around the outdoor unit, it may
cause an explosion.

Earth the unit correctly.

• Do not connect the earth wire to a gas pipe, water pipe, light­ning rod, or a telephone ground wire. Improper earthing may
cause electric shock.

CAUTION

Install an earth leakage breaker depending on the installa­tion location of the air conditioner (such as highly humid
areas).

• If an earth leakage breaker is not installed, it may cause electric
shock.

Ensure that the drain water is properly drained.

• If the drain passage is improper, water may drip down from
the indoor/outdoor unit, wetting and damaging the furniture.

In case of an abnormal condition

Immediately stop operating the air conditioner and consult your dealer.

SAFETY PRECAUTIONS

Do not operate switches with wet hands.

• This may cause electric shock.

Do not clean the air conditioner with water or place an object
that contains water, such as a flower vase, on it.

• This may cause fire or electric shock.

Do not step on or place any object on the outdoor unit.

• This may cause injury if you or the object falls down.

For installation

Your MITSUBISHI ELECTRIC product is designed and manufactured with high
quality materials and components which can be recycled and/or reused.
This symbol means that electrical and electronic equipment, batteries and
accumulators, at their end-of-life, should be disposed of separately from your
household waste.
If a chemical symbol is printed beneath the symbol (Fig. 1), this chemical sym­bol means that the battery or accumulator contains a heavy metal at a certain
concentration. This will be indicated as follows:
Hg: mercury (0,0005%), Cd: cadmium (0,002%), Pb: lead (0,004%)
In the European Union there are separate collection systems for used electrical
and electronic products, batteries and accumulators.
Please, dispose of this equipment, batteries and accumulators correctly at your
local community waste collection/recycling centre.

Note:

This symbol mark is for EU countries only.
This symbol mark is according to the directive 2002/96/
EC Article 10 Information for users and Annex IV, and/
or to the directive 2006/66/EC Article 20 Information for
end-users and Annex II.

To dispose of this product, consult your dealer.

DISPOSAL

Fig. 1

En-3

• OPERATING INSTRUCTIONS •

Temperature buttons

Page 4

Off-timer button Page 6

On-timer button Page 6

TIME set buttons Pages 3, 6
HR. button
MIN. button

CLOCK button Page 3

RESET button Page 3

Lid
Slide down to open

WIDE VANE button

Page 5

Before operation: Insert the power supply plug into the power outlet and/or turn the breaker on.

Display section

Operation indicator
lamp

Remote control
receiving section

Emergency
operation
switch Page 4

Remote controller
holder

Signal transmitting
section
Distance of signal :
About 6 m

Beep(s) is (are) heard
from the indoor unit when
the signal is received.

Operation display
section

ON/OFF
(operate/stop)
button

Operation
select
button Page 4

ECONO
COOL

button

Page 6

FAN speed
control button

Page 5

VANE
control button

Page 5

• Install the remote control­ler holder to a place where
the signal can be received
by the indoor unit.

Use the remote controller provided with the unit only.
Do not use other remote controllers.

Horizontal vane

Vertical vane

Air outlet

Air filter
(Catechin air filter)

Air inlet

Front panel

Air cleaning filter (Option)

Outdoor unit

Installing the remote controller batteries Setting current time

NAME OF EACH PART

PREPARATION BEFORE OPERATION

1.

Press CLOCK

3.

Press CLOCK again

2.

Press the TIME set buttons to

set the time

Each time

/ is
pressed, the set time increases
by 1 hour/minute.

Indoor unit Remote controller

Outdoor units may be different in appearance.

LONG
button

Page 6

• Make sure the polarity of the batteries is correct.

•

Do not use manganese batteries. The remote controller could malfunction.

• Do not use rechargeable batteries.

• Replace all batteries with new ones of the same type.

• Batteries can be used for approximately 1 year. However, batteries with
expired shelf lives last shorter.

• Press RESET gently using a thin instrument.

If the RESET button is not pressed, the remote controller may not operate

correctly.

1.

Remove the front lid

2.

Insert AAA

alkaline batteries

3.

Install the front lid

4.

Press RESET

• Press CLOCK gently using a thin instrument.

Air inlet (back and side)

Piping

Drainage hose

Air outlet

Drain outlet

MSH type
MS type

MSH type :

MS type :

En-4

1

Press

to start the operation.

2

Press to select operation mode. Each press
changes mode in the following order:

3

Press or to set the temperature.
Each press raises or lowers the temperature by 1°C.

Press to stop the operation.

• The same setting is selected the next time by simply pressing .

(I FEEL) (COOL) (DRY) (FAN)

Operation indicator lamp

Operation indicator lamp

The operation indicator lamp shows the operation state of the unit.

Indication Operation state Room temperature

The unit is operating to reach the set
temperature

About 2°C or more
away from set tem­perature

The room temperature is approach­ing the set temperature

About 1 to 2°C from
set temperature

Lighted Not lighted

Emergency operation

When the remote controller cannot be used...

Emergency operation can be activated by pressing the emergency operation
switch (E.O.SW) on the indoor unit.

Each time the E.O.SW is pressed, the operation changes in
the following order:

Auto restart function

If a power failure occurs or the main power is turned off during operation, “Auto
restart function” automatically starts operation in the same mode as the one set
with the remote controller just before the shutoff of the main power. When
timer is set, timer setting is cancelled and the unit starts operation when power
is resumed.

If you do not want to use this function, please consult the service repre­sentative because the setting of the unit needs to be changed.

SELECTING OPERATION MODES

Set temperature : 24°C
Fan speed : Medium
Horizontal vane : Auto

Note:

The first 30 minutes of operation is test run. Temperature
control does not work, and fan speed is set to High.

I FEEL mode

The unit selects the operation mode according to the room temperature
when I FEEL is selected. When the room temperature is higher than 25°C,
COOL is selected (set temperature: 24°C). When the room temperature is
lower than 25°C, DRY is selected. However, when operation is stopped and
then started within 2 hours, the mode which has been selected previously
is operated. With MSH type, when the room temperature is lower than
23°C, HEAT is selected.

Note:

During COOL operation, the set temperature may not be changed when
the room temperature is more than 2°C higher than the set temperature.
In this case, please wait until the room temperature drops to within 2°C of
the set temperature.

COOL mode

Enjoy cool air at your desired temperature.

DRY mode

Dehumidify your room. The room may be cooled slightly.
Temperature cannot be set during DRY mode.

FAN mode <MS type>

Circulate the air in your room.

HEAT mode <MSH type>

Enjoy warm air at your desired temperature.

<MSH type>
<MS type>

<MS type>

<MSH type>

(I FEEL) (COOL) (DRY) (HEAT)

<MSH type>

<MS type>

Emergency
COOL

Emergency
HEAT

Stop

<MSH type>

Emergency
COOL

Stop

<MS type>

En-5

• OPERATING INSTRUCTIONS •

Press to select fan speed. Each press changes
fan speed in the following order:

• Two short beeps are heard from the indoor unit when set to AUTO.

Press to select airflow direction. Each press
changes airflow direction in the following order:

• Two short beeps are heard from the indoor unit when set to AUTO.

Press to select horizontal airflow direction. Each
press changes airflow direction in the following order:

Vertical airflow direction

(AUTO)

The vane is set to the most efficient airflow direction. COOL/DRY:horizontal
position. FAN/HEAT:downward position.

(Manual)

For efficient air conditioning, select upper position for COOL/DRY. During
COOL/DRY, when the vane is set to position (4) or (5), the vane automati­cally moves to horizontal position after 1 hour to prevent water dripping.

(Swing)

The vane moves up and down intermittently.

(AUTO) (Low) (Med.) (High)

(AUTO) (1) (2) (3) (4) (5) (SWING)

FAN SPEED AND AIRFLOW DIRECTION ADJUSTMENT

(

SWING

)