Mitsubishi MAA150DXN07 Specification
Global LCD Panel Exchange Center
www.panelook.com
TENTATIVE
All information in this technical data sheet is tentative
and subject to change without notice.
15.0”XGA
TECHNICAL SPECIFICATION
MAA150DXN07
Melco Display Technology Inc.
Date: Jun.29, ’07
MDTI Confidential (1/23) MAA150DXN07_02_00
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
CONTENTS
No. Item Page
-- COVER 1
www.panelook.com
-- CONTENTS 2
1 APPLICATION 3
2 OVERVIEW 4
3 ABSOLUTE MAXIMUM RATINGS 5
4 ELECTRICAL CHARACTERIST ICS 5, 6, 7
5 INTERFACE PIN CONNECTIO N 8, 9
6 INTERFACE TIMING 10, 11, 12, 13, 14
7 BLOCK DIAGRAM 15
8 MECHANICAL SPECIFICATION 16, 17
9 OPTICAL CHARACT ERISTICS 18, 19
10 RELIABILITY TEST CONDITION 20
11 HANDLING PRECAUTIONS FOR TFT-LCD MODULE 21, 22, 23
MDTI Confidential (2/23) MAA150DXN07_02_00
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
1. APPLICATION
This specification applies to color TFT-LCD module, MAA150DXN07.
These specification papers are the proprietary product of Melco Display Technology Inc. (“MDTI”)
and include materials protected under copyright of MDTI. No part of this document may be
reproduced in any form or by any means without the express written permission of MDTI.
MDTI does not assume any liability for infringement of patents, copyrights or other intellectual
property rights of third parties by or arising from use of a product specified in this doc ument. No
license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual
property rights of MDTI or of others.
MDTI classifi es the usage of th e TFT- LC D modu le as f o ll ows. Pl ease c o nf i r m the u sag e be fo r e u sin g
the product.
(1) Standard Usage
(2) Special Usage
(3) Specific Usage
Computers, office equipment, factory automation equipment, test and measurement
equipment, communications, transportation equipment(automobiles, ships, trains, etc.),
provided, however, that operation is not influenced by TFT-LCD directly.
Medical equipment, safety equipment, transportation equipment, provided, however, that
TFT-LCD is necessary to its operation.
Cockpit Equipment, military systems, aerospace equipment, nuclear reactor control systems,
life support systems and any other equipment. MDTI should make a contract that stipulate
apportionment of responsibilities between MDTI and our customer.
www.panelook.com
The product specified in this document is designed for “Standard Usage” unless otherwise specified
in this document. If customers intend to use the product for applications other than those specified
for “Standard Usage”, they should contact MDTI sales representative in adva nce.
MDTI has been making continuous effort to improve the reliability of its products. Customers
should implement sufficient reliability design of their application equipments such as redundant
system design, fail-safe functions, anti-failure features.
MDTI assumes no responsibility for any damage resulting from the use of the product that does not
comply with the instructions and the precautions specified in this document.
MDTI Confidential (3/23) MAA150DXN07_02_00
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
2. OVERVIEW
MAA150DXN07 is 15.0” color TFT-LCD (Thin Film Transistor Liquid Crystal Display) modules
composed of LCD panel, driver ICs, control circuit, and backlight unit.
By applying 6 bit or 8 bit digital data, 1024 × 768, 262K-col or or 16.7M-c olor im ages are di splayed
on the 15.0” diagonal screen. Input power voltage is 3.3 V for LCD driving.
The type of data and control sig nals are digital and transmitted vi a LVDS inte rface per Typ. 65
MHz clock cycle.
Inverter for backlight is not included in this module. General specifications are summarized in the
following table:
ITEM SPECIFICATION
www.panelook.com
Display Area (mm)
Number of Dots 1024 × 3 (H) × 768 (V)
Pixel Pitch (mm) 0.297 (H) × 0.297 (V)
Color Pixel Arrange ment RGB vertical s tripe
Display Mode Normally white TN
Number of Color 262K(6 bit/color)16.7M(8 bit/color)
Luminance (cd/m2) 450
Wide Viewing Angle Technology Optical Compensation F ilm
Viewing Angle (CR ≥ 10) -75~75° (H) -60~50° (V)
Surface Treatment Anti-glare and hard-coating 3H
Electrical Interface LVDS(6 bit/8 bit)
Optimum Viewing Angle (Contrast ratio) 6 o’clock
Module Size (mm) 326.0 (W) × 255.0 (H) × 16.6 (D)
Module Mass (g) 1380
304.1 (H) × 228.1 (V)
(15.0-inch diagonal)
Backlight Unit CCFL, 4-tube s, edge-light, replaceab le
Characteristic value without any note is typical value.
MDTI Confidential (4/23) MAA150DXN07_02_00
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
g
g
y
www.panelook.com
3. ABSOLUTE MAXIMUM RATINGS
ITEM SYMBOL MIN. MAX. UNIT
Power Supp l y Vo ltage for LCD VCC 0 4.0 V
Logic Input Voltage VI −0.3 VCC+0.3 V
Lamp Voltage VL 0 2500 Vrms
Lamp Current IL 0 10.0 mArms
Lamp Frequency FL -- 100 kHz
Operation Temperature (Panel)
Operation Temperature (Ambient)
Storage Temperature
[Note]
1) Measured at the center of active area and at the center of panel back surface
2) Top,Tstg ≤ 40°C : 90%RH max. without condensation
Top,Tstg > 40°C : Absolute humidity shall be less than t he value of 90%RH at 40 °C without
condensation.
Note 1,2)
T
Note 2)
T
Note 2)
T
op(Panel)
op(Ambient)
stg
−20 70 °C
−20 70 °C
−20 80 °C
4. ELECTRICAL CHARACTERISTICS
(1) TFT- LCD Ambient Temperature : Ta = 25°C
ITEM SYMBOL MIN. TYP. MAX. UNIT Remarks
Power Supp l y Vo ltage for LCD VCC 3. 0 3.3 3.6 V *1)
Power Supply Current for LCD ICC -- 410 700 mA *2)
Permissive Input Ripple Voltage VRP -- -- 100 mVp-p VCC = +3 .3 V
Logic Input Voltage
*1) Power and signals sequence:
LCD Power Supply
Lo
ic Signal
High VIH 2.0 -- VCC+0.3 V MODE, SC
Low VIL 0 -- 0.8 V MODE, SC
t1
≤ 10 ms 200 ms ≤ t4
0 < t2
≤ 50 ms 200 ms ≤ t5
0 < t3
≤ 50 ms 0 ≤ t6
VCC
㩷
0.9VCC
data
0.1VCC
0.9VCC
0.1VCC
0.1VCC
t2
Backli
t1
VL
ht Power Suppl
t5 t6
data: RGB DATA, DCLK, DENA, MODE, SC
t3
t4
MDTI Confidential (5/23) MAA150DXN07_02_00
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
VCC-dip conditions:
1) When 2.6 V
≤ VCC < 3.0 V, t d ≤ 10 ms
2) When VCC < 2. 6 V
VCC-dip conditions should also follow the power and signals sequence.
*2) Typical current condition:
64-gray-bar-pat tern(6 bit )
256-gray-bar-pattern(8 bit)
768 line mode
VCC = +3.3 V, f
www.panelook.com
2.6 V
td
= 48.4 kHz, fV= 60 Hz, f
H
3.0 V
= 65 MHz
CLK
VCC
(2) Backlight Ta = 25°C
ITEM SYMBOL MIN. TYP. MAX. UNIT Remarks
Lamp Voltage VL -- 620 -- Vrms IL = 6.5 mArms
Lamp Current IL 3.5 6.5 8.0 mArms *2),*6)
Lamp Frequency FL 40 -- 70 kHz *3)
1300 -- -- Vrms Ta = 25°C
Starting Lamp Voltage VS
1500 -- -- Vrms Ta = 0°C
1650 -- -- Vrms Ta = −20°C
Lamp Life Time LT 50000 -- -- h
*4),*5) IL = 6.5 mArms,
Continuous Operation
*1) Please use synchronous inverter.
*2) Lamp Current measurement method (The current meter is inserted in low voltage line.)
A
A
Power
A
A
Inverter
Supply
LCD
Module
CTL
CTL
CTH
CTH
CTL
CTL
CTH
CTH
*3) Lamp frequency of inverter may produce interferenc e with horizontal synchr onous frequency,
and this may cause horizontal beat on the d is play. Therefore, please adjust lamp frequency, and
keep inverter as far from module as possible or use electronic shielding between inverter and
module to avoid the interference.
MDTI Confidential (6/23) MAA150DXN07_02_00
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
*4) Lamp life time is defined as the time either when the brightness becomes 50% of the initial
value, or when the starting lamp voltage does not meet the value specified in this ta ble.
*5) The life time of the backlight depends on the ambient temperature. The life time will decrease
under low/high temperature.
*6) Please use the inverter which has symmetrical current wave form as follows,
The degree of unbalance: less than 10%
www.panelook.com
The ratio of wave height: less than
CURRENT WAVE FORM
±10%
2
I
PH
I
PL
IPH: High side peak
I
: Low side peak
PL
The degree of unbalance = |IPH - IPL| / Irms
The ratio of wave height = I
(or IPL) / Irms
PH
100(%)
×
MDTI Confidential (7/23) MAA150DXN07_02_00
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Loading...