Mitsubishi MAA121DSL02 Specification
Global LCD Panel Exchange Center
12.1” SVGA
www.panelook.com
TENTATIVE
All information in this technical data sheet is tentative
and subject to change without notice
TECHNICAL SPECIFICATION
MAA121DSL02
Melco Display Technology Inc.
Date: Jan.25,’07
MDTI Confidential (1/22) MAA121DSL02_02_00
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
CONTENTS
No. Item Page
-- COVER 1
-- CONTENTS 2
1 APPLICATION 3
www.panelook.com
2 OVERVIEW 4
3 ABSOLUTE MAXIMUM RATINGS 5
4 ELECTRICAL CHARACTERIST ICS 5, 6, 7
5 INTERFACE PIN CONNECTIO N 8, 9
6 INTERFACE TIMING 10, 11, 12, 13
7 BLOCK DIAGRAM 14
8 MECHANICAL SPECIFICATION 15, 16
9 OPTICAL CHARACT ERISTICS 17, 18
10 RELIABILITY TEST CONDITION 19
11 HANDLING PRECAUTIONS FOR TFT-LCD MODULE 20, 21, 22
MDTI Confidential (2/22) MAA121DSL02_02_00
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
1. APPLICATION
This specification applies to color TFT-LCD module, MAA121DSL02.
These specification papers are the proprietary product of Melco Display Technology Inc. (“MDTI”)
and include materials protected under copyright of MDTI. No part of this document may be
reproduced in any form or by any means without the express written permission of MDTI.
MDTI does not assume any liability for infringement of patents, copyrights or other intellectual
property rights of third parties by or arising from use of a product specified in this document. No
license, express, implied or otherwise, is granted under any patents, copyrights or other
intellectual property rights of MDTI or of others.
MDTI classifies the usage of the TFT-LCD module as follows. Please confirm the usage before using
the product.
(1) Standard Usage
(2) Special Usage
(3) Specific Usage
Computers, office equipment, factory automation equipment, test and measurement
equipment, communications, transportation equipment(automobiles, ships, trains, etc.),
provided, however, that operation is not influenced by TFT-LCD directly.
Medical equipment, safety equipment, transportation equipment, provided, however, that
TFT-LCD is necessary to its operation.
Cockpit Equipment, military systems, aerospace equipment, nuclear reactor control systems,
life support systems and any other equipment. MDTI should make a contract that stipulate
apportionment of responsibilities between MDTI and our customer.
www.panelook.com
The product specified in this document is designed for “Standard Usage” unless otherwise specified
in this document. If customers intend to use the product for applications other than those specified
for “Standard Usage”, they should contact MDTI sales representative in adva nce.
MDTI has been making continuous effort to improve the reliability of its products. Customers
should implement sufficient reliability design of their application equipments such as redundant
system design, fail-safe functions, anti-failure features.
MDTI assumes no responsib ility for any da mage resulting from the use of the product that does not
comply with the instructions and the precautions specified in this document.
MDTI Confidential (3/22) MAA121DSL02_02_00
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
2. OVERVIEW
MAA121DSL02 is 12.1” color TFT-LCD (Thin Film Transistor Liquid Crystal Display) module
composed of LCD panel, driver ICs, control circuit, and backlight unit.
By applying 6 bit digital data, 800 × 600, 262k-col or images are displayed on the 12.1” diagonal
screen. Input power voltage is single 3.3V or 5.0V for LCD driving.
The type of date and control signals are digital and transmitted via CMOS interface per typ.
40MHz clock cycle.
Inverter for backlight is not included in this module. General specifications are summarized in the
following table:
ITEM SPECIFICATION
Display Area (mm)
Number of Dots 800 × 3 (H) × 600 (V)
www.panelook.com
246.0(H) × 184.5(V)
(12.106-inch diagonal)
Pixel Pitch (mm) 0.3075 (H) × 0.3075 (V)
Color Pixel Arrangement RGB vertical stripe
Display Mode Normally white TN
Number of Color 262k
Luminance(cd/m2) 400
Wide Viewing Angle Technology Optical compensation Film
Viewing Angle(CR≥10) -65∼65°(H) -75∼45°(V)
Surface Treatment Anti-reflection and hard-coating 2H
Electrical Interface CMOS
Optimum Viewing Angle(Contrast ratio) 6 o’clock
Module Size (mm) 280.0 (W) × 210.0 (H) × 12.0 (D)
Module Mass (g) 720
Backlight Unit CCFL, 2-tube s, edge-light, replaceab le
Characteristic value without any note is typical value.
MDTI Confidential (4/22) MAA121DSL02_02_00
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
3. ABSOLUTE MAXIMUM RATINGS
ITEM SYMBOL MIN. MAX UNIT
Power Supply Voltage for LCD VCC 0 6.0 V
Logic Input Voltage VI -0.3 6.5 V
Lamp Voltage VL 0 2000 Vrms
Lamp Current IL 0 18 mArms
Lamp Frequency FL -- 80 kHz
Operation Temperature(Panel)
Operation Temperature(Ambient)
Storage Temperature
[Note]
1) Measured at the center of active area and at the center of panel back surface
2) Top,Tstg ≤ 40°C : 90%RH max. without condensation
Top,Tstg > 40°C : Absolute humidity shall be less than t he value of 90%RH at 40 °C without
condensation.
www.panelook.com
Note 1,2)
Note 2)
Note 2)
T
op(Panel)
T
op(Ambient)
T
stg
-20 70 °C
-20 70 °C
-20 80 °C
4. ELECTRICAL CHARACTERISTICS
(1) TFT-LCD Ambient temperature: Ta = 25℃
ITEM SYMBOL MIN. TYP. MAX. UNIT Remarks
Power Supply
Voltage for LCD
Power Supply
Current for LCD
3.3V pow e red VCC 3.0 3.3 3 .6 V
5.0V pow e red VCC 4.75 5.0 5.25 V
3.3V powered ICC -- 340 500 mA
5.0V powered ICC -- 220 340 mA
Permissive Input Ripple Voltage VRP -- -- 100 mVp-p VCC = +3.3V/5.0V
Logic Input
Voltage
High VIH 2.0 -- 5.25 V
Low VIL 0 -- 0.8 V
*1) Power and signals sequence:
t1 ≤ 10 ms 400 ms ≤ t4
0 < t2 ≤ 50 ms 200 ms ≤ t5
0 < t3 ≤ 50 ms 0 ≤ t6
VCC
LCD Power Supply
Logic Signal
㩷
0.1VCC
0.9VCC
data
0.9VCC
0.1VCC
0.1VCC
*1)
*1)
*2)
*2)
t2
t1
Backlight
Backlight Power Supply
t5 t6
data: RGB DATA, DCLK, HD, VD, DENA
t3
t4
MDTI Confidential (5/22) MAA121DSL02_02_00
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
VCC-dip conditions:
(a) 3.3 V powered
1) When 2.7 V
2) When VCC < 2. 7 V
VCC-dip conditions should also follow the power and signals sequence.
(b) 5.0V powered
1) When 4.2 V
2) When VCC < 4. 2 V
VCC-dip conditions should also follow the power and signals sequence.
www.panelook.com
≤ VCC < 3.0 V, t d ≤ 10 ms
VCC
3.0V
2.7V
td
≤ VCC < 4.5 V, t d ≤ 10 ms
VCC
4.5V
4.2V
td
*2) Typical current condition:
64-gray-bar pattern
600 line mode
VCC = +3.3 V / 5.0 V, f
=37.9kHz, fV=60.3Hz, f
H
= 40MHz
CLK
(2) Backlight Ta = 25℃
ITEM
SYMBOL
MIN. TYP. MAX. UNIT Remarks
Lamp Voltage VL -- 540 -- Vrms IL = 12.0 mArms
Lamp Current IL 6.0 12.0 14.0 mArms *2),*6)
Lamp Frequency FL 30 -- 60 kHz *3)
1000 -- -- Ta = 25°C
Starting Lamp Voltage VS
1200 -- -- Ta = 0°C
1290 -- --
Lamp Life Time LT 50,000 -- -- h
Vrms
Ta = -20°C
*4),*5)IL = 12.0 mArms,
Continuous operation
*1) Please use synchronous inverter.
*2) Lamp Current measurement method (The current meter is inserted in low voltage line.)
A
Inverter
Power
Supply
LCD
Module
CTL
CTH
CTH
MDTI Confidential (6/22) MAA121DSL02_02_00
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
*3) Lamp frequency of inverter may produce interferenc e with horizontal synchronous frequency,
and this may cause horizontal beat on the display. Therefore, please adjust lamp frequency, and
keep inverter as far from module as possible or use electronic shielding between inverter and
module to avoid the interference.
*4) Lamp life time is defined as the time either when the brightness becomes 50% of the initial
value, or when the starting lamp voltage does not meet the value specified in this ta ble.
*5) The life time of the backlight depends on the ambient temperature. The life time will decrease
under low/high temperature.
*6) Please use the inverter which has symmetrical current wave form as follows,
The degree of unbalance: less than 10%
www.panelook.com
The ratio of wave height: less than
I
PH
I
PL
CURRENT WAVE FORM
±10%
2
IPH: High side peak
I
: Low side peak
PL
The degree of unbalance = |IPH - IPL| / Irms
The ratio of wave height = I
(or IPL) / Irms
PH
100(%)
×
MDTI Confidential (7/22) MAA121DSL02_02_00
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Loading...