Mitsubishi DIS900D operation manual

ID PHOTO SYSTEM DIS900D

OPERATION MANUAL

CONTENTS

1 SAFETY PRECAUTIONS ......................................................................................... 3 - 5

2 UNPACKING...................................................................................................................6

3 PRINTER SETUP ..................................................................................................... 7 - 9

4 CONNECTION..............................................................................................................10

5 TAKING A PICTURE ..............................................................................................11 - 13

6 PICTURE QUALITY ADJUSTMENT..................................................................... 14 - 19

7 FEATURES AND FUNCTIONS............................................................................. 20 - 21

8 ADVANCED SETTING.......................................................................................... 22 - 31

9 TROUBLESHOOTING..................................................................................................32

10 SPECIFICATIONS ........................................................................................................33

CONTENTS

This system is composed by the following components.

Options

Printer

(not provided from Mitsubishi)

• AC cable

• Operation manual

• Ink cassette

• Printer driver

• Spacers

• Screws

Page

Tripod

Camera

System

Monitor

• System cable

• Operation manual

Flash

This system complies with the requirements of the EC Directive 89/336/EEC "EMC Directive" as amended by Directive 93/68/EEC. The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on small-scale enterprises, inside as well as outside of the buildings. All places of operation are characterised by their connection to the public low voltage power supply system.

1. SAFETY PRECAUTIONS

In the interest of safety, please observe the following precautions:

POWER REQUIREMENT

This system is designed for operation on 120V AC or 220V-240V, 50/60Hz AC. Never connect to any outlet or power supply having a different voltage or frequency.

WARNING: THIS APPARATUS MUST BE EARTHED. AVERTISSEMENT: CET APPAREIL DOIT ETRE MIS A LA TERRE.

PROTECTIVE MEASURES

IF ABNORMALITIES ARISE, .....

Use of the unit during emission of smoke or abnormal sounds (without adopting countermeasures) is dangerous. In such a case, unplug the power cord from the source outlet immediately, and request maintenance service from the sales dealer.

NEVER INSERT ANY OBJECT INTO THE UNIT

Foreign objects of an kind inserted into this unit constitute a safety hazard and can cause extensive damage.

DO NOT PLACE ANYTHING ON THE DIGITAL COLOR PRINTER

Heavy objects placed on the Digital color printer can cause damage or obstruct proper ventilation.

PROTECT THE POWER CORD

Damage to the power cord may cause fire or shock hazard. When unplugging, hold by the plug only and remove carefully.

DO NOT PLACE WATER CONTAINERS ON THE UNIT

Do not place flower vases, and other water-holding containers on the device. If, for some reason, water seeps to the inside of the unit, unplug the power cord from the source outlet, and contact the sales dealer. If used without corrective measures, the unit may be damaged. "In the interest of safety, avoid handling of liquids near the unit."

DO NOT REMOVE THE CABINET

Touching internal parts is dangerous, and it may lead to malfunction. Contact the sales dealer to carry out internal checks and adjustments. Before opening the cover to remove jammed paper, etc., be sure to disconnect the power cord plug.

UNPLUG THE POWER CORD IF THE UNIT IS NOT IN USE

Turn off the MAIN power switch and unplug the power cord if the unit is not in use for extended periods.

WHEN TRANSPORTING THE UNIT

When transporting the unit, remove the sheet cartridge and paper from the paper cassette.

BE CAREFUL AROUND PRINT PAPER EXIT SLOT

Don't insert your hand or any material into the paper exit slot during printing. Don't touch the cutter blade inside the paper exit slot as this can cause injury.

DO NOT TOUCH THE THERMAL HEAD

Do not touch the thermal head (located inside the unit). The thermal head is heated to high temperature and may cause injury.

BE CAREFUL WITH THE PRINTING UNIT

Don't move the unit while the drawer is open. This may cause injury. Be careful not to catch your finger in the printing unit while the drawer is being closed.

CONNECTION CABLES

Only use the cables provided.

INSTALLATION LOCATIONS

MAINTAIN GOOD VENTILATION

Ventilation slots and holes are provided on the top, sides and bottom of this unit. Place the unit on a hard and level surface and locate at least 10 cm from walls to insure proper ventilation. When putting the unit on the system rack, ensure there is a space between the unit and the back of the rack.

UNSUITABLE LOCATIONS

Avoid uneven surfaces or hot-springs areas where hydrogen sulfide and acidic ions are likely to be generated.

PLACES WITH HIGH HUMIDITY AND DUST

Do not place the unit in locations with high humidity and dust. They can cause extensive damage. Avoid places where unit is likely to be exposed to oily fumes and vapours.

PLACES LIKELY TO BE EXTREMELY HOT

Places exposed to direct sunlight, or near heating appliances can attain extremely high temperatures, which may deform the cabinet, or cause other damage.

PLACE THE UNIT ON A HORIZONTAL SURFACE

The unit is likely to be affected if it is placed in slanted conditions or in unstable places.

PROTECT AGAINST DEW FORMATION

In extremely cold regions, if the unit is moved quickly from an extremely cold place to warmer one, dew is likely to be formed. If dew is formed, printing is not possible.

OPERATING AMBIENT TEMPERATURE RANGE

The operating ambient temperature range is 5°C- 40°C, and humidity of 20-80%. When using the unit on the system rack, be sure to keep this ambient temperature inside the rack.

FOR LONG OPERATING LIFE

UNSUITABLE MATERIALS FOR THE DIGITAL COLOR PRINTER

Coat flaking and deformation are likely to occur if the unit is wiped with chemical dusters, benzine, thinner or any other solvent, if rubber or PVC items are left in contact with the unit for extended duration, or if the unit is sprayed with insecticide.

CARE OF THE CABINET

Unplug and clean with a soft cloth slightly moistened with a mild soap and water solution. Allow to dry completely before operating. Never use petroleum based solutions or abrasive cleaners.

HEAD ABRASION

The thermal head, like the video head, wears out. When it is abraded, it becomes hard to print out fine details of the picture. In such a case, it is necessary to replace the thermal head. Consult with the sales dealer for replacing the head.

CAUTION ON RELOCATING

When transporting this unit, make sure it is not likely to be subjected to impacts. They can be a prime cause for damage. Also, make sure to disconnect the power cord from the power outlet, and all cables from the devices.

CONNECTING DEVICES

Read thoroughly "Operating Precautions" of the instruction booklets for the devices connected with the Digital color printer. The power cord must be disconnected after printing is over.

OTHER CAUTIONS

Dust or other foreign matter adhering to the print paper or the sheet cartridge, or deformation resulting from exposure to extremely low or high temperatures could cause loss of colour, uneven colour or lines, or wrinkles in the print images.

NOTE: YOUR UNDERSTANDING IS REQUESTED FOR THE LOSS OF IMAGES IN MEMORY DUE TO THE SUDDEN OCCURRENCE OF A MALFUNCTION.

2. UNPACKING

Take the unit out of the box by the following procedures. Make sure to check the contents.

PRINTER

1 Open the top of the box.

2 Remove the accessory box.

3 Remove the cushion above the unit.

4 Take the unit out of the box carefully.

Make sure to keep the unit horizontal. Then, unwrap the packing.

• Accessory box

Power cord

Ink cassette Operation manual

Printer driver

CAMERA, ETC.

1 Open the top of the box.

2 Take out the system cable and

operation manual.

3 Remove the top cushion.

4 Take the camera out of the box

carefully.

3. PRINTER SETUP

Before printing a photo, install print paper and ink cassette.

UNLOCK THE PRINTING UNIT

See CP900DW(ID) operation manual for details.

RELEASING THE PRINTING UNIT LOCK

1 Press down the knob to pull out the tray.

2 Shift the printing unit lock switch to the right (UNLOCK).

INSTALLING PRINT PAPER

Do not remove the seal on the print paper yet.

1 Insert the print paper roller with gear on the left.

Press the folder 1 as shown right, and set the print paper roller.

2 Set the other side of roller without gear.

Gear

Front side

Left side

Seal

Right side

3 Remove the seal, and insert the edge of the print paper

right below the roller cover with arrow marks towards the front panel.

Make sure to insert the paper straight.

4 Feed the print paper through the paper outlet by hand.

5 Pull both sides of the print paper to eliminate slack.

INSTALLATION OF INK SHEET

arrow marks

INSTALLING THE INK SHEET

Load the ink sheet into the cassette before inserting the cassette into the printer.

1 Put the ink sheet rollers with flat tops into the holes of ink

cassette.

Put the white roller (rolled with ink sheet) to the ink cassette first.

Then, put the colored roller (without ink sheet) to the ink

cassette.

2 Position the other sides of rollers. Set IC at this time.

IC chip with the IC holder is attached to the ink sheet. Set the IC holder to the ink cassette as shown right.

NOTE

• Do not remove the IC chip or IC holder from the ink sheet. Removal of the IC will stop the printer from functioning correctly.

• Set the projected part of the IC holder to the correct position as shown below.

Projected part

colored roller

white roller

IC holder

INSTALLING THE INK CASSETTE

1 Eliminate any slack of the ink sheet.

Hold the colored roller and turn the white roller.

2 Insert the ink cassette with the ink sheet into its

compartment.

Put the ink cassette with flat top side to each 1. Then, set the other side (with handle) as shown right. When exchanging the ink sheet, remove the cassette by holding the handle.

INSERT THE PRINTING UNIT

1 Push the printing unit until it is locked into place.

2 After plugging the power cord, press POWER button on the

front panel.

3 Press FEED&CUT button.

The print paper is automatically cut after feeding about 10 cm (4 inches).

4 Repeat the above step 3 once or twice.

Feeding the print paper will eliminate fingerprints and dust during handling. The printing unit is initialized.

NOTE

An IC is built in the ink sheet. This is the IC chip, not a battery. This IC is safe to be thrown away with normal waste.

4. CONNECTION CABLE CONNECTION

Connect the components as follows.(example) Make sure to turn off each device when connecting. After connecting the cables, make sure to set the cover over the terminals on the camera. (See page 21 for removing and setting the cover.)

Flash (option)

External flash (option)

Monitor (option)

To OPTION I/F

System cable

To AC LINE

AC power cord (supplied with the printer)

To USB

DPS system

5. TAKING A PICTURE

You can take up to four pictures (without Compact FlashTM), and choose the best one.

1 Connect the camera and the printer.

2 Turn on the printer.

The camera is also turned on.

3 Switch the camera to CAMERA mode.

• When the camera is turned on, it is set to CAMERA mode.

• If PLAY mode is selected, press CAMERA/PLAY button.

• The printing area, face guide, multi format setting, color setting and memory position are displayed.

4 Select the type of multiple picture (1, 2, 4, 4D, 6, 16 or 1L) by

MULTI button.

Each time the button is pressed, the format changes. 1 1-image (75x100mm) 2 2-image (50.8x74mm) 4,4D 4-image (36.5x48mm) 6 6-image (30x35mm) 16 16-image (19x25mm)

CAMERA mode

Printing area

F a c e guide

Memory position

Color setting

Multi format setting

1 2 4

4D 6 16

5 Press T (+) or W (-) button to adjust the size to fit the face in

the face guide.

Adjust the position where:

• The face is positioned just within the upper and lower horizonetal lines on the LCD.

• The nose is aligned with the vertical line at the center of the LCD.

6 Press EV button to adjust brightness when taking picture.

EXP. is displayed.

NOTE

• If FLASH : OFF is selected on CAPTURE menu, EV is displayed.

7 Press T (+) or W (-) button to adjust the brightness.

To make an image brighter, increase the value. To make an image darker decrease the value.

8 Press SET button.

9 Press SHOT button halfway to adjust focus.

During focus adjusting, the focus mark ( ) is blinking. When focus is adjusted, the focus mark stops blinking.

Focus mark

A Press SHOT button down completely to take a picture.

The image is memorized in the camera. When an image is memorized, II mark will appear. The camera is switched to PLAY mode. A mark will be displayed.

Shows memorization completed.

PLAY mode mark

Position the image memorized (when using Compact Flash)

NOTE

• Four images can be memorized in the camera.

• When a Compact Flash is inserted, the images are memorized in the Compact Flash first.

B When taking more pictures, press CAMERA/PLAY button.

Switch the camera to CAMERA mode. Then, repeat the above steps 9 to 10.

• If brightness of the image is not adjusted correctly, repeat the above steps 6 to 10.

Position the image memorized (when not using Compact Flash)

+ 25 hidden pages