Mitsubishi Diamante 1997 User Manual

mitsubishi :: Mitsubishi Diamante ES Sedan V6-

3.5L SOHC (1997)

> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Alarm Horn Relay > Component Information > Locations

Alarm Horn Relay: Locations

Theft Alarm System Overall View And Views A - F

RELAY VIEW

Theft-alarm Horn Relay A

> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Alarm Module, (Vehicle Antitheft) > Component Information > Locations

Alarm Module: Locations

Control Unit Location Overall View

Control Unit Location View A - D

Component View

ETACS-ECU B

> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Alarm Module, (Vehicle Antitheft) > Component Information > Locations > Page 10

Alarm Module: Testing and Inspection

> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Alarm Module, (Vehicle Antitheft) > Component Information > Locations > Page 11

Diamante ES Sedan V6-3.5L SOHC (1997)

ETACS-ECU Terminal Check

ETACS-ECU Terminal Check

> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Keyless Entry Module > Component Information > Testing and Inspection

Keyless Entry Module: Testing and Inspection
ETACS-ECU (KEYLESS ENTRY) TERMINAL VOLTAGE CHECK

Connector Terminal No 1 - 53

> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Keyless Entry Module > Component Information > Testing and Inspection > Page 15

Diamante ES Sedan V6-3.5L SOHC (1997)

PART 1 OF 2

Connector Terminal No 55 - 66

PART 2 OF2

For ETACS-ECU code related diagnosis refer to: Computers and Control Systems, Information Bus, Testing and Inspection.NOTE:

> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Keyless Entry Module > Component Information > Testing and Inspection > Page 16

> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Keyless Entry Module > Component Information > Testing and Inspection > Page 17

> Relays and Modules > Relays and Modules - Body and Frame > Door Module > Component Information > Locations

Door Module: Locations

Overall View

View F

> Relays and Modules > Relays and Modules - Body and Frame > Door Module > Component Information > Locations > Page 22

> Relays and Modules > Relays and Modules - Body and Frame > Fuel Door Release Relay > Component Information > Locations

Fuel Door Release Relay: Locations

Overall View

View G

> Relays and Modules > Relays and Modules - Body and Frame > Fuel Door Release Relay > Component Information > Locations > Page 26

Fuel Door Release Relay: Testing and Inspection

Trunk Lid And Fuel Filler Door Opener Relay Continuity Check

Trunk Lid And Fuel Filler Door Opener Relay Continuity Check

> Relays and Modules > Relays and Modules - Body and Frame > Keyless Entry Module > Component Information > Testing and Inspection

Keyless Entry Module: Testing and Inspection
ETACS-ECU (KEYLESS ENTRY) TERMINAL VOLTAGE CHECK

Connector Terminal No 1 - 53

> Relays and Modules > Relays and Modules - Body and Frame > Keyless Entry Module > Component Information > Testing and Inspection > Page 30

Diamante ES Sedan V6-3.5L SOHC (1997)

PART 1 OF 2

Connector Terminal No 55 - 66

PART 2 OF2

For ETACS-ECU code related diagnosis refer to: Computers and Control Systems, Information Bus, Testing and Inspection.NOTE:

> Relays and Modules > Relays and Modules - Body and Frame > Keyless Entry Module > Component Information > Testing and Inspection > Page 31

> Relays and Modules > Relays and Modules - Body and Frame > Keyless Entry Module > Component Information > Testing and Inspection > Page 32

> Relays and Modules > Relays and Modules - Body and Frame > Power Mirror Control Module > Component Information > Description and Operation

Power Mirror Control Module: Description and Operation

-

When the remote-controlled mirror switch is operated while the ignition key is in "ACC" or "ON" position, the front door module (LH) determinesoperator requirements according to switch output signals.The front door module (LH) positions the LH door mirror by driving the mirror motors or sends a signal to the assist-ECU via the SWScommunication line.The assist-ECU drives the RH door mirror motors to position the mirror according to the signal received.

> Relays and Modules > Relays and Modules - Body and Frame > Power Seat Control Module > Component Information > Locations

Power Seat Control Module: Locations

Control Unit Location Overall View

Control Unit Location E - J

Component View

Memory Power Seat ECU J

> Relays and Modules > Relays and Modules - Body and Frame > Power Seat Control Module > Component Information > Locations > Page 39

Power Seat Control Module: Testing and Inspection

> Relays and Modules > Relays and Modules - Body and Frame > Power Seat Control Module > Component Information > Locations > Page 40

Diamante ES Sedan V6-3.5L SOHC (1997)

Memory Power Seat ECU Terminal Check

Memory Power Seat ECU Terminal Check

> Relays and Modules > Relays and Modules - Body and Frame > Sunroof / Moonroof Module > Component Information > Locations

Sunroof / Moonroof Module: Locations

Overall View

View C

> Relays and Modules > Relays and Modules - Body and Frame > Trunk / Liftgate Relay > Component Information > Locations

Trunk / Liftgate Relay: Locations

Overall View

View G

> Relays and Modules > Relays and Modules - Body and Frame > Trunk / Liftgate Relay > Component Information > Locations > Page 47

Trunk / Liftgate Relay: Testing and Inspection

Trunk Lid And Fuel Filler Door Opener Relay Continuity Check

Trunk Lid And Fuel Filler Door Opener Relay Continuity Check

> Relays and Modules > Relays and Modules - Brakes and Traction Control > ABS Main Relay > Component Information > Locations

ABS Main Relay: Locations

Construction Diagram

> Relays and Modules > Relays and Modules - Brakes and Traction Control > ABS Main Relay > Component Information > Locations > Page 52

Valve Relay Check (Part 1 Of 2)

> Relays and Modules > Relays and Modules - Brakes and Traction Control > ABS Main Relay > Component Information > Locations > Page 53

ABS Main Relay: Testing and Inspection

Motor Relay Check (Part 1 Of 2)

Motor Relay Check (Part 2 Of 2)

MOTOR RELAY CHECK

Valve Relay Check (Part 1 Of 2)

Valve Relay Check (Part 2 Of 2)

VALVE RELAY CHECK

> Relays and Modules > Relays and Modules - Brakes and Traction Control > Electronic Brake Control Module > Component Information > Locations

Electronic Brake Control Module: Locations

Control Unit Location Overall View

Control Unit Location E - J

Component View

ABS-ECU F

> Relays and Modules > Relays and Modules - Brakes and Traction Control > Electronic Brake Control Module > Component Information > Testing and Inspection > Terminal Resistance & Continuity Check

Electronic Brake Control Module: Testing and InspectionTerminal Resistance & Continuity Check

Terminal Resistance And Continuity Checks

1. Turn the ignition switch to "OFF."2. Disconnect the ABS-ECU connector.3. Measure the resistance and check for continuity between the terminals of the ABS-ECU harness-side connector while referring to the check chart.

NOTE:

- When measuring resistance and checking continuity, a harness for checking contact pin pressure should be used instead of inserting a test probe.

- Checks do not have to be carried out in the order given in this chart.

CAUTION:

If resistance or continuity checks are performed on the wrong terminals, damage to the vehicle wiring, sensors, ABS-ECU, and/orohmmeter may occur. Use care to prevent this.

4. If ohmmeter shows any deviation from the normal condition, check the corresponding sensor, actuator and related electrical: wiring, then repair or
replace.

5. After repair or replacement, recheck with the ohmmeter to confirm that the repair or replacement has corrected the problem.

> Relays and Modules > Relays and Modules - Brakes and Traction Control > Electronic Brake Control Module > Component Information > Testing and Inspection > Terminal Resistance & Continuity Check > Page 59

Electronic Brake Control Module: Testing and InspectionTerminal Voltage Check

Terminal Voltage Check Chart

1. Turn the ignition switch to "OFF."2. Disconnect the ABS-ECU connector.3. Measure the voltage at the terminals of the ABS-ECU harness-side connector while referring to the check chart.

NOTE:

- When measuring voltage, a harness for checking contact pin pressure should be used instead of inserting a test probe.

- Checks do not have to be carried out in the order given in this chart.

CAUTION:

Short-circuiting the positive (+) probe between a connector terminal and ground could damage the vehicle wiring, the sensor, ABS-ECU,or all three. Use care to prevent this.

4. If voltmeter shows any deviation from standard value, check the corresponding sensor, actuator and related electrical wiring, then repair or
replace.

5. After repair or replacement, recheck with the voltmeter to confirm that the repair has corrected the problem.

> Relays and Modules > Relays and Modules - Brakes and Traction Control > Electronic Brake Control Module > Component Information > Testing and Inspection > Page 60

Electronic Brake Control Module: Service and Repair

Electronic Control Unit

REMOVAL AND INSTALLATION

- Remove under cover and glove box. Refer to "Instrument Panel, Gauges and Warning Indicators."

Reverse procedure to install.

1. Remove ABS-ECU bracket.2. Remove ABS-ECU.-

> Relays and Modules > Relays and Modules - Cooling System > Radiator Cooling Fan Motor Relay > Component Information > Locations

Radiator Cooling Fan Motor Relay: Locations

Relay Location Overall View

> Relays and Modules > Relays and Modules - Cooling System > Radiator Cooling Fan Motor Relay > Component Information > Locations > Page 65

Diamante ES Sedan V6-3.5L SOHC (1997)

Relay Location View A - J

RELAY VIEW

Radiator Fan Relay (MI,HI,LO) C

> Relays and Modules > Relays and Modules - Cooling System > Radiator Cooling Fan Motor Relay > Component Information > Locations > Page 66

Radiator Cooling Fan Motor Relay: Testing and Inspection

RELAY CONTINUITY CHECK

Refer to illustration for testing procedure.

> Relays and Modules > Relays and Modules - Cruise Control > Cruise Control Module > Component Information > Locations

Cruise Control Module: Locations

Control Unit Location Overall View

Control Unit Location View A - D

Component View

Auto Cruise ECU D

> Relays and Modules > Relays and Modules - HVAC > Blower Motor Relay > Component Information > Locations

Blower Motor Relay: Locations

Relay Location Overall View

> Relays and Modules > Relays and Modules - HVAC > Blower Motor Relay > Component Information > Locations > Page 75

Diamante ES Sedan V6-3.5L SOHC (1997)

Relay Location View A - J

RELAY VIEW

Blower Motor Relay D
Blower Motor Relay (high) H

> Relays and Modules > Relays and Modules - HVAC > Blower Motor Relay > Component Information > Locations > Page 76

Blower Motor Relay: Testing and Inspection

BLOWER RELAY CONTINUITY CHECK

> Relays and Modules > Relays and Modules - HVAC > Compressor Clutch Relay > Component Information > Locations

Compressor Clutch Relay: Locations

Relay Location Overall View

> Relays and Modules > Relays and Modules - HVAC > Compressor Clutch Relay > Component Information > Locations > Page 80

Diamante ES Sedan V6-3.5L SOHC (1997)

Relay Location View A - J

RELAY VIEW

Air Conditioning Compressor C
Clutch Relay

> Relays and Modules > Relays and Modules - HVAC > Compressor Clutch Relay > Component Information > Locations > Page 81

Compressor Clutch Relay: Testing and Inspection

A/C COMPRESSOR CLUTCH RELAY, CONDENSER FAN RELAY (LO) AND (HI) CONTINUITY CHECK

> Relays and Modules > Relays and Modules - HVAC > Condenser Fan Motor Relay, HVAC > Component Information > Locations

Condenser Fan Motor Relay: Locations

Relay Location Overall View

> Relays and Modules > Relays and Modules - HVAC > Condenser Fan Motor Relay, HVAC > Component Information > Locations > Page 85

Diamante ES Sedan V6-3.5L SOHC (1997)

Relay Location View A - J

RELAY VIEW

Condenser Fan Relay(HI),(LO) C

> Relays and Modules > Relays and Modules - HVAC > Control Module HVAC > Component Information > Locations

Control Module HVAC: Locations

A/C Control Unit

AC Control Unit

Belt Lock Controller

Belt Lock Controller

> Relays and Modules > Relays and Modules - Instrument Panel > Panel Illumination Control Module > Component Information > Locations

Panel Illumination Control Module: Locations

Control Unit Location Overall View

Control Unit Location View A - D

Component View

Instrument Panel ECU C

> Relays and Modules > Relays and Modules - Instrument Panel > Panel Illumination Control Module > Component Information > Locations > Page 93

Panel Illumination Control Module: Testing and Inspection

Instrument Panel ECU Terminal Check

> Relays and Modules > Relays and Modules - Instrument Panel > Panel Illumination Control Module > Component Information > Locations > Page 94

Diamante ES Sedan V6-3.5L SOHC (1997)

Instrument Panel ECU Terminal Check

> Relays and Modules > Relays and Modules - Lighting and Horns > Fog/Driving Lamp Relay > Component Information > Locations

Fog/Driving Lamp Relay: Locations

Relay Location Overall View

> Relays and Modules > Relays and Modules - Lighting and Horns > Fog/Driving Lamp Relay > Component Information > Locations > Page 99

Diamante ES Sedan V6-3.5L SOHC (1997)

Relay Location View A - J

RELAY VIEW

Fog Light Relay C

> Relays and Modules > Relays and Modules - Lighting and Horns > Fog/Driving Lamp Relay > Component Information > Locations > Page 100

Fog/Driving Lamp Relay: Testing and Inspection

Fog Light Relay Continuity Check

Fog Light Relay Continuity Check - Chart

> Relays and Modules > Relays and Modules - Lighting and Horns > Headlamp Relay > Component Information > Locations

Headlamp Relay: Locations

Relay Location Overall View