MINOURA P-500AL-2 Instruction Manual

P-500AL-2 "Pair Stand"

instructions manual

MINOURA North America MINOURA Japan Headquarters

(for U.S. residents only) (for ALL worldwide customers)

1996 East Avenue, Hayward, CA 94541 U.S.A. 1197-1 Godo, Anpachi, Gifu 503-2305 Japan

Phone [phone] Fax [phone]

Fax [phone] Mail [e-mail]

Mail [e-mail] Web www.minoura.jp

MADE IN JAPAN

Contact

If you have any questions or need help, you should contact the dealer where you purchased or the Minoura
distributor in your country rst. The distributor can be found on our web site.

Only when you cannot get enough service, you can contact us.

!

Minoura strongly recommends placing the
P-500AL-2 next to a wall for safety to prevent
from falling backward accident.

- 1 -

Cradle Hook is padded with soft foamed PVC coating
to prevent scratch problem to your bike frame

The upper cradle height is adjustable in two positions

The main pillar is made of single light alloy tubing
for lightweight and great stiffness

Bike Cradle is angle adjustable to t your bike frame's top-tube angle.
Also each Cradle Hook is position & angle adjustable for perfect t

The lower Bike Cradle position is fully adjustable with

Minoura's original stainless band clip II

Unique K-shaped leg design is stable and allows to set
P-500AL-2 next to the wall for minimizing space

(ver.2.1 2009/07)

The stainless band clip has been modied to be easier

assembling type. P-500AL-2 adopts 45mm type band

How To Setup Your P-500AL-2

Top Frame

Main Pillar

Cradle Hook

Support Bar

Rear LegFront Leg (L)

Base Plate

Front Leg (R)

Foot Adjuster

Cradle Bar

Required Tools: 1 x 5mm Hex Wrench (included)
1 x 10mm Spanner
1 x 13mm Spanner

A) Cradle Support

B) Angle Adjust Plate

(projection is foreside)

C) Alloy Bar & Cradle Hook

Completed Bike Cradle

(order is C, B and A from foreside)

Bolt Variation

Type-A

(plain type)

Type-B

(w/ spring washer)

Type-C

(w/ at & spring

washers)

1

Base Plate

Collar

Flat
Washer

M6x35 Bolt (A)

Front Leg

(R)

Connect both Front Legs to the Base Plate using the Collar, Flat Washer,

M6x35 Bolt (type-A) and Nylon Nut. (see Fig. B)

Nylon Nut

2

Place the Rear Leg on the assembled Base Plate and place the Pillar

Base on top of the legs .

Insert the M6x45 Bolt (type-A) with a at washer into the foreside

hole on the Pillar Base, then tighten to the Base Plate. (see Fig. C)

In order to make the next step easier, do not fully tighten the bolt yet.

Pillar Base

M6x45 Bolt (A)

3

Insert another M6x45 Bolt (type-A) using a at washer into the hole on

the backside. Make sure the bolt goes through the center hole of the

Rear Leg, then tighten it rmly. (see Fig. D)

Now tighten the rst M6x45 Bolt (type-A) down rmly.

M6x45 Bolt (A)

Nylon Nut

Nylon Nut

<Fig. A>

<Fig. B>

<Fig. C>

<Fig. D>

Front Leg (L)

- 2 -

Flat Washer

Flat Washer

!

Be sure the Collar insertion direction is different
on right and left side leg. Refer the Fig. B closely
when assembling.

!

Choose the Front Legs as the Support Bar locates
INSIDE of each leg. If the bar is located outside,
you won't be able to assemble the bars correctly.