MINOURA EBS-3 User Manual

3-tier bicycle storage stand
EBS-3
instructions manual
Read this instructions carefully before assembling to understand how each part should be connected.
1,800mm
1,680mm
(Ver. 1.0 2011/11)
660mm
770mm
520mm
950mm
400mm
400mm
IMPORTANT NOTES
!
270mm
1,030mm
[completed style and dimensions]
• For standard 2-wheel bike including e-Bike. Any other bikes such as recumbent, wheelbase is 920mm or shorter, tire outer diameter is 320mm or smaller, or tire width is wider than 56mm are not permitted to use with this stand.
• The ladder frame is constructed durable enough to be capable with the weight of your body and bike for mounting bike on the stand, but the total weight should be limited up to 100 kgs including bike. And we recommend to step on or close to the side frame.
• To keep the bike on EBS-3 stable, both wheels must sit in the wheel cradles properly and the front tire must be held from upside too. If the bike is equipped with fender or rear rack, the bike must be set rightward.
• Setup EBS-3 on at and level oor. If the oor has been slanted, we don't guarantee the bike stability.
• When need to move EBS-3, you must remove all bikes prior to action.
• Check regularly every bolt and nut is properly tightened. Use correct tools for assembling and maintenance.
Contact
MINOURA JAPAN
1197-1 Godo, Anpachi, Gifu 503-2305 Japan Phone +81-584-27-3131 / Fax +81-584-27-7505 / minoura@minoura.jp
- 1 -
Made in Japan
How To Assemble EBS-3
Required Tools:
1 x 10mm Spanner 1 x M4 Hex Wrench
Assemble Side Frame
1
Assemble Side Frame with M6x10 bolts and M6 spring washers in the Parts-Pack #3.
Both frames are exactly same. There is no fixed direction.
Be sure the longer pillar
!
has xed direction.
There is a hole on the pillar side to be connected with Beam Frame. This side must be on bottom.
2 x 13mm Spanner
(both Right and Left side)
M6 Spring Washer
M6x10 Bolt
Lower Frame
(ring type wrench is recommended) (ring type wrench is recommended)
Upper Frame
Pillar (Long)
Pillar (Short)
Connect Side Frames
2
Connect Side Frames and Beam Frame with M6x40 bolts, M6 spring washers and Collar (short) in the Parts-Pack #4.
!
Side Frames are exactly same, so the larger hole for inserting Collar is always located on the left side.
M6x40 Bolt
M6 Spring Washer
Collar (Short / 26mm)
Beam Frame
- 2 -
Collar works to prevent deforming the tube by being inserted together with bolt. Do not miss it.
Install Tire Holder Frame
3
(3 sets)
Install Tire Holder Frame to Front Frame with 4 sets of M6x30 bolt, M6 Flat and Spring washers and M6 Cap Nut.
Make this 3 sets.
M6 Cap Nut
M6 Flat Washer
M6 Spring Washer
M6x30 Bolt
You should place the
!
round head of M6x30 bolt inward in order to avoid scratching the tire.
Tire Holder Frame
Tire Holder
Front Frame
Assemble Ladder Frame
4
(3 sets)
Assemble Front Frame, Rear Frame and Joint Tubes with 4 sets of M6x30 bolt, M6 Spring and Flat Washers, and M6 Cap Nut in the Parts-Pack #1.
Make this 3 sets.
M6x30 Bolt
M6 Spring Washer
M6 Flat Washer
M6 Cap Nut
Rear Frame
Front Frame
Joint Tube
The rear wheel support is temporally xed in the package with tape.
!
You will need to adjust its position to t the actual bike wheelbase,
so remove the tape when start using EBS-3.
- 3 -
Assemble Ladder Frames onto Side Frames
5
Assemble Ladder Frame to Side Frame with M8x50 Bolt (M8x15 on mid level), M8 Spring and Flat Washers, Collar (Long) and M8 nut in the Parts-Pack #2.
M8x50 Bolt
(top & low level)
M8 Spring Washer
Collar (Long / 31mm)
M8 Flat Washer
M8 Nut
M8x15 Bolt (mid level)
M8 Spring Washer
Be sure you use different
!
size bolt on the mid level.
How To Mount Bike
NOTE : This section describes that the bike is set rightward and the front wheel is held by the tire holder.
At first, place the front wheel in the right side wheel cradle.
1
Slide the rear wheel cradle on the Rear Frame to fit the actual bike's wheelbase, then place the rear wheel
2
in the cradle. It's not necessary to fix the rear cradle position.
While supporting bike with your hand, loosen the backside knob bolt on the Tire Holder then slide it down.
3
When it reaches the tire, tighten the knob to fix the position. Now the bike is securely supported at 3 points.
Finally, shake the bike on EBS-3 slightly
4
to check if it's supported stable. Now you can step away.
- 4 -
Loading...