Milton CAT TL642 User Manual

Specifications

®

Cat

TL642

Telehandler

Engine

Model Cat® 3054C DIT
Gross Power (Basic) 74 kW 99 hp
Net Power (Basic) 70.4 kW 94.5 hp

• Net Power shown is the power available at the flywheel
when equipped with fan, air cleaner, muffler and alternator.

Weights

Operating Weight 9180 kg 20,240 lb

Operating Specifications

Rated Load Capacity 2948 kg 6,500 lb
Maximum Lift Height 12.8 m 42 ft
Maximum Forward Reach 9.1 m 30 ft
Frame Leveling 10°
Top Travel Speed 30 kph 20.4 mph
Capacity at Max Height 2948 kg 6,500 lb
Capacity at Max Reach 317 kg 700 lb
Turning Radius over Tires 3.7 m 12 ft

Hydraulic System — Implement

Gear Pump Single-section

• Auxiliary Hydraulic Circuit used for all attachments equipped
with cylinders or other hydraulic components. Consists of valves,
controls and hydraulic lines.

Service Refill Capacities

Fuel Tank 144 L 38 gal
Hydraulic System 151.4 L 40 gal

Tires

Standard 13.00 x 24-12 PR
Optional 13.00 x 24 Foam Filled

13.00 x 24 Rock Lug

13.00 x 24 Solid

Transmission Speeds

Forward 4 speed
Reverse 3 speed

Boom Performance

Boom Up 13 Seconds
Boom Down 10 Seconds
Tele In 13 Seconds
Tele Out 14 Seconds
Drawbar Pull (Loaded) 80.07 kN 18,000 lb

Axles

• Trunnion mounted planetary 55 degree steer axles.

• Integral steer cylinder.

• High bias limited slip differential on front axle.

Brakes

• Service Brakes are inboard wet disc brakes on front and rear axles.

• Parking Brakes are spring-applied hydraulic release on front axle.
Light on dash indicates when brake is on.

Instruments

• Volt meter, hourmeter, engine oil pressure gauge, fuel gauge, water
temperature gauge. All gauges protected by clear acrylic cover.

Work Tools

Hydraulic IT Includes Includes
IT Coupler Auxiliary Electrics Auxiliary Electrics

Pallet Forks (2) 1524 mm, (2) 60 in, 2 in x 6 in
51 mm x 152 mm
(2) 1219 mm, (2) 48 in, 2.36 in x 4 in
60 mm x 102 mm

Cubing Forks (2) 1219 mm, (2) 48 in, 2 in x 2 in
51 mm x 51 mm

Standard Tilt 1270 mm 50 in
Carriage

Wide Tilt 1829 mm 72 in
Carriage

Standard Rotate 1270 mm 50 in
Carriage

Wide Rotate 1829 mm 72 in
Carriage

Swing Carriage 100°, 1829 mm, 4028 kg 100°, 72 in, 9,000 lb
Capacity, 2268 kg Swung Capacity, 5,000 lb Swung

Side Shift 1.22 m 48 in
Carriage

TL642 Telehandler

8.5 m (28 ft)

9.7 m (32 ft)

10.9 m (36 ft)

12.1 m (40 ft)

13.4 m (44 ft)

7.3 m (24 ft)

6.1 m (20 ft)

4.9 m (16 ft)

3.7 m (12 ft)

2.4 m (8 ft)

-2.4 m (-8 ft )

1.2 m (4 ft)

0 m (0 ft)

-1.2 m (-4 ft)

3.7 m

(12 ft)

4.9 m

(16 ft)

6.1 m

(20 ft)

7.3 m

(24 ft)

8.5 m

(28 ft)

9.7 m

(32 ft)

2.4 m
(8 ft)

1.2 m
(4 ft)

0 m

(0 ft)

E

F

0°

10°

20°

30°

40°

50°

60°

70°

-9°

317 kg (700 lb)

907 kg (2,000 lb)

1361 kg (3,000 lb)

1814 kg (4,000 lb)

2722 kg (6,000 lb)

2948 kg (6,500 lb)

Dimensions

All dimensions are approximate.

2.41 m (95.5 in) 3.25 m (128 in)

95.5 in. (2.41 m)

Load Chart and Dimensions

2.38 m (94 in)

94 in. (2.38 m)

16.4 in.

416 mm (16.4 in)

(416 mm)

128 in. (3.25 m)

221.6 in. (6.33 m)

5.63 m (221.6 in)

TL642

13.4 m (44 ft)

12.1 m (40 ft)

10.9 m (36 ft)

9.7 m (32 ft)

8.5 m (28 ft)

7.3 m (24 ft)

6.1 m (20 ft)

4.9 m (16 ft)

3.7 m (12 ft)

2.4 m (8 ft)

1.2 m (4 ft)

0 m (0 ft)

-1.2 m (-4 ft)

-2.4 m (-8 ft )

9.7 m

(32 ft)

10°

0°

30°

20°

317 kg (700 lb)

-9°

8.5 m

(28 ft)

7.3 m

(24 ft)

50°

40°

907 kg (2,000 lb)

4.9 m

6.1 m
(16 ft)

(20 ft)

70°

60°

2722 kg (6,000 lb)

1814 kg (4,000 lb)

1361 kg (3,000 lb)

3.7 m

2.4 m
(8 ft)

1.2 m
(4 ft)

(12 ft)

F

E

D

C

B

A

2948 kg (6,500 lb)

80

70

60

50

40

TL642

30

20

10

-10

0 m

(0 ft)

IMPORTANT

Rated lift capacities shown are with machine
equipped with carriage and pallet forks. The
machine must be level on a firm surface with
undamaged, properly inflated tires. Machine
specifications and stability are based on rated
lift capacities at specific boom angles and
boom lengths. (If specifications are critical, the
proposed application should be discussed with
your dealer.)

DO NOT exceed rated lift capacity loads, as
unstable and dangerous machine conditions

-10

10

20

30

40

60

50

80

70

TL642

will result.

DO NOT tip the machine forward to determine
the allowable load.

Use only JLG approved attachments
with proper material handler model/
attachment load capacity charts displayed
in the operator’s cab. OSHA requires all
rough terrain forklift operators be trained
according to OSHA 29 CFR 1910.178 (1).

Due to continuous product improvements,
machine specifications and/or equipment
changes may be made without prior
notification. This machine meets or exceeds
ANSI/ITSDF B56.6-2005 as originally
manufactured for intended applications.

For more complete information on Cat products, dealer services, and industry solut iions, visit us on the web at
www.cat .com

© 2010 Caterpillar
Printed in U.S.A.
All rights reserved.

CAT, CATERPILL AR, their respective logos, “Caterpillar Yellow” and the POWER EDGE trade dress, as well as
corporate and product identity used herein, are trademarks of C aterpillar and may not be used without permission.

AEHQ583 9-0 4 (03-2010)