Operating instructions
for automatic detergent
dispensing unit
AWD 10
To avoid the risk of accidents
or damage to the appliance,
it is essential to read these
operating instructions before it is installed
and used for the first time.
en - AU, NZ
M.-Nr. 07 917 340
Contents
Caring for the environment..........................................3
Warning and Safety instructions .....................................4
View of appliance..................................................6
Front view.........................................................6
Rear view .........................................................6
Components in the packaging ........................................6
Installation and connection .........................................7
Location possibilities for the detergent dispensing unit .....................7
Fastening bracket ..................................................8
Connecting the hoses ...............................................9
Connection to the washing machine .................................9
Connecting the detergent dispensing unit .............................9
Connecting the plug ...............................................10
Before using for the first time.......................................11
Filling the automatic detergent dispensing unit...........................11
Preparing the appliance for use ......................................11
Cleaning and care ................................................12
Cleaning the liquid detergent container d...............................12
Cleaning the powder detergent container c ............................14
Cleaning the paddle wheel........................................14
Cleaning the container and stirring device............................15
Problem solving guide ............................................17
No detergent or too little detergent was dispensed .......................17
An unsatisfactory wash result ........................................18
General problems .................................................19
2
Caring for the environment
Disposal of the packing
material
The packing material protects the
detergent dispensing unit from
transport damage. The transport and
protective packing has been selected
from materials which are
environmentally friendly for disposal
and can normally be recycled.
Rather than just throwing these
materials away, please ensure they are
offered for recycling. You can return the
packaging to your local Miele
Chartered Agent.
Disposing of your old
appliance
Electrical and electronic appliances
often contain materials which, if
handled or disposed of incorrectly,
could be potentially hazardous to
human health and to the
environment.They are, however,
essential for the correct functioning of
your appliance. Please do not therefore
dispose of it with your household waste.
Please dispose of it at your local
community waste collection / recycling
centre and ensure that it presents no
danger to children while being stored
for disposal.
3
Warning and Safety instructions
This appliance is not intended for
This appliance complies with all
relevant local and national safety
requirements. Improper use of the
appliance can, however, present a
risk of both personal injury and
material damage.
To avoid the risk of accidents and
damage to the appliance, please
read these instructions carefully
before installation and before using
it for the first time. They contain
important information on its safety,
installation, use and maintenance.
Keep these instructions in a safe
place and ensure new users are
familiar with the content. Pass them
on to any future owner.
Correct application
The detergent dispensing unit must
~
only be used in conjunction with a Miele
washing machine. It should be used
exclusively for dispensing domestic
washing detergent and for the washing
of textiles. Any other use may be
dangerous. The manufacturer cannot
be held liable for damage resulting
from incorrect or improper use or
operation.
~
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience or knowledge, unless they
have been given supervision or
instruction concerning its use by a
person responsible for their safety.
Safety with children
This appliance is only intended for
~
use by adults who have read these
instructions. This appliance is not a toy!
To avoid the risk of injury, keep children
well away and do not allow them to play
with it or to use the controls. They will
not understand the potential dangers
posed by it.
Older children may use the
~
detergent dispensing unit only when its
operation has been clearly explained to
them and they are able to use it safely.
They must be aware of the potential
dangers caused by incorrect operation.
Technical safety
Before setting up the detergent
~
dispensing unit, check it for any
externally visible damage.
Do not install or use a damaged
detergent dispensing unit.
Faulty components must only be
~
replaced by genuine Miele original
spare parts. The manufacturer can only
guarantee the safety of the appliance
when Miele replacement parts are
used.
4
Warning and Safety instructions
Unauthorised repairs could result in
~
unforeseen dangers for the user, for
which Miele cannot accept liability.
Repairs should only be undertaken by a
Miele approved service technician,
otherwise the warranty will be
invalidated.
If the connection cable is faulty, it
~
must only be replaced by a Miele
approved service technician to protect
the user from danger.
In the event of a fault or for cleaning
~
purposes, the detergent dispensing
unit is only completely isolated from the
electricity supply when:
– the plug is withdrawn from the rear of
the washing machine.
The Miele water protection system
~
protects from water damage provided
the following conditions have been met:
– The machine is correctly plumbed in
and connected to the electricity
supply.
Do not make any alterations to the
~
detergent dispensing unit, unless
authorised to do so by Miele.
Correct use
Do not install the detergent
~
dispensing unit in a room where there is
a risk of frost occurring. Frozen hoses
may tear or burst.
If detergent comes into contact with
~
eyes, rinse out immediately with
lukewarm water. If swallowed, see a
doctor immediately. Persons with skin
wounds or sensitive skin should avoid
contact with washing detergent.
Accessories
Only use genuine Miele spare parts
~
and accessories with this appliance.
If non-Miele parts are used, warranty,
performance and product liability
claims may be invalidated.
Miele cannot be held liable for
damage caused by non-compliance
with these Warning and Safety
instructions.
5
View of appliance
Front view
a Base
b Indicator lights
Left:
Powder dispensing is activated
Centre:
Right:
c Powder detergent container
d Liquid detergent container
In-operation indicator
Liquid dispensing is activated
Rear view
a Suds drain connection (water soluble
detergent)
b Connection cable with plug
(Connection for the plug is located
on the rear of the washing machine)
c Water inlet connection
Components in the packaging
The following are enclosed in the
packaging:
–
The base of the detergent
dispensing unit
–
One container for powder detergent
–
One container for liquid detergent
–
Two hoses for inlet and drain
–
Fastening bracket
–
A plastic bag with screws (6 screws
for attaching the hose and 2 for
attaching the fastening bracket)
6
Installation and connection
Location possibilities for the
detergent dispensing unit
For safety reasons, the detergent
,
dispensing unit must not be installed
above power sockets, switches,
lamps and other electrical
appliances.
The detergent dispensing unit
should be easily accessible, e.g. for
refilling with detergent.
There are several different location
possibilities.
ON
ON
ON
a On the lid of the washing machine
b Next to the washing machine on a
shelf
c On a wall bracket (optional
accessory)
d In an adjoining furniture cabinet
7
Installation and connection
Fastening bracket
The fastening bracket ensures the
detergent dispensing unit is securely
installed on top of the washing
machine. The fastening bracket
prevents the dispensing unit from
"roaming" during spin cycles.
The fastening bracket must be
,
screwed to the top of the washing
machine if the machine is positioned
on a plinth or flooring subject to
vibrations, e.g. timber flooring.
Attaching the fastening bracket
– adhering the fastening bracket
The rear surface of the fastening
bracket is adhesive.
screwing on fastening bracket
–
After adhering the fastening bracket,
^
screw it to the lid of the washing
machine with the screws supplied.
To attach the fastening bracket
,
to lid of the washing machine, the
screws supplied must be used.
Other screws may damage the
washing machine.
^
Pay attention to the distance
dimensions of the dispensing unit
and the top of the washing machine
to avoid the dispensing unit
protruding over the edge of the lid.
^
Remove the paper from the
underside of the fastening bracket
and adhere the bracket to the lid of
the washing machine.
8
^
Position the base of the dispensing
unit on top of the fastening bracket.
Connecting the hoses
Connection to the washing machine
Installation and connection
Pay attention to the diameter of the
^
ends of the hoses.
^ Take the 6 screws out of their bag.
^
Unscrew the cap on the back of the
washing machine.
^
Keep the two screws for later when
attaching the hoses.
Tip for easier installation
rings of the hoses with water or suds
beforehand.
^ Push the hoses firmly into the
corresponding openings and fasten
them with the enclosed screws.
Connecting the detergent dispensing
unit
^
Pay attention to the diameter of the
ends of the hoses.
: Wet the O-
9
Installation and connection
The hoses can be attached to the
detergent dispensing unit at different
angles, depending on the installation
situation.
Tip for easier installation:
of the hoses with water or suds
beforehand.
Wet the seals
Connecting the plug
The socket for the plug is located on
the rear panel of the washing machine.
^ Loosen the catch and withdraw the
cap from the socket.
^
Push the hoses firmly into the
corresponding openings and fasten
them to the detergent dispensing
unit.
10
^
Insert the plug and fasten it with the
catch.
,
The cap needs to be replaced
and locked into place when moving
the machine.
Filling the automatic detergent
dispensing unit
Take care to put detergents in
,
the appropriate containers.
d = Liquid detergent
Open the container's cover.
^
Remove detergent packaging.
^
Fill until the maximum filling level with
^
liquid detergent.
Tip:
Turn the liquid detergent bottle upside
down over the container to empty it
completely.
Before using for the first time
Place the container onto the bracket.
^
Push down the liquid detergent
container d firmly so that the base
valve opens.
^ Close the cover so that the liquid
detergent doesn't become dry or so
that foreign objects don't get into the
container.
The container has a base valve that
opens automatically when placed onto
the bracket.
c = Powder detergent
^
Open the container's cover.
^
Fill until the maximum filling level with
powder detergent.
Close the cover so that the powder
detergent doesn't clump together or so
that foreign objects don't get into the
container.
Preparing the appliance for
use
See "Automatic detergent dispensing"
in the operating instructions for
information on how to programme the
electronics of the washing machine for
automatic detergent dispensing.
11
Cleaning and care
Do not use solvents, abrasive
,
cleaners, glass cleaners or allpurpose cleaning agents.
These might damage plastic
surfaces and other components
because of the chemicals they
contain.
^ Remove the containers from the
bracket to clean them.
Cleaning the liquid detergent
container d
Clean the liquid detergent container
twice a year or when changing liquid
detergents.
^ Remove both covers.
^ The bracket should only be wiped
with a well-wrung-out damp cloth.
12
^
Unscrew and remove the base valve
in the container.
Rinse the base valve under warm
^
running water.
^ Wash out any detergent residue from
the container with warm water.
^ Clean the container and covers with
a mild non-abrasive cleaning agent
or soap and water. Wipe dry with a
soft cloth.
Cleaning and care
^ Replace and tighten the base valve.
13
Cleaning and care
Cleaning the powder detergent
container c
Cleaning the paddle wheel
Due to longer periods of non-use,
powder detergent may clump
together in the paddle wheel.
Check the paddle wheel regularly for
clogging and clean it on average
every three months.
Remove the cover.
^
Unscrew both screws from the
^
dispenser compartment cover and
remove it.
^
Pour any powder detergent present
into another container for storage.
^
Turn the container upside down.
14
^
Take out the paddle wheel and clean
it with warm water.
^
Dry the paddle wheel with a soft
cloth.
The paddle wheel must be dry to
avoid the powder detergent
clumping together.
^
Put the paddle wheel and cover back
in the reverse order.
^
Then tighten the screws.
Cleaning and care
Cleaning the container and stirring
device
Clean the container and stirring
device twice a year.
Remove the cover.
^
Pour any powder detergent present
^
into another container for storage.
Remove the paddle wheel as
^
described on the previous page.
Turn the stirring device a little further
^
with the help of the coupling.
^ Loosen the screw on the coupling
and remove the coupling from the
stirring device.
^ Turn the container upside down.
^
Before loosening the coupling,
ensure that the stirring device in the
dispenser compartment is visible.
Otherwise the stirring device will not
be able to be removed later.
^
Remove the stirring device.
15
Cleaning and care
Wash out any detergent residue from
^
the container with warm water.
Danger of injury! Do not remove
,
any incrustation on the stirring
device with force or with a sharp
object.
Soak the stirring device in warm
^
water instead.
Clean the paddle wheel and cover
^
with warm water.
Dry the container, stirring device,
^
paddle wheel and cover with a soft
cloth.
To avoid powder detergent
clumping together, the container,
stirring device, paddle wheel and
cover need to be completely dry.
^ Put the container back together in the
reverse order.
^ Then tighten the screws.
16
Problem solving guide
No detergent or too little detergent was dispensed
Problem Possible cause Remedy
The in-operation
indicator light doesn't
light up after
switching on the
washing machine.
No detergent was
dispensed.
No powder detergent
was dispensed.
No liquid detergent
was dispensed.
The detergent
dispensing unit is not
connected to the
washing machine.
The container selected
is empty.
Automatic detergent
dispensing has not
been activated.
The detergent has
become clogged in the
paddle wheel.
The container is
blocked or the paddle
wheel has not been
fitted.
The container has been
overfilled.
Check whether the
venting in the container
cover is blocked.
Check the plug connection on
the back of the washing
machine.
Add detergent.
Select the automatic
detergent dispensing function
for the next wash programme.
Clean the container as
described in "Cleaning and
care".
Make sure you do not exceed
the maximum filling level
marked on the container.
Clean the container as
described in "Cleaning and
care".
The liquid detergent
has dried.
Clean the container, add new
liquid detergent and seal the
container with the cover.
17
Problem solving guide
The amount of
detergent dispensed
is too small.
If the fault may be caused by something else, call Miele.
The basic dosage
quantity is not
sufficient.
Increase the dosage
–
quantity and, if necessary,
select a higher degree of
soiling.
How to set the dosage
–
quantity is described in
"Automatic detergent
dispensing" in the washing
machine's operating
instructions.
An unsatisfactory wash result
Problem Possible cause Remedy
Liquid detergent does
not give the required
result.
Grey, greasy particles
cling to washed
laundry.
Liquid detergents do
not contain bleaching
agents. They do not
always remove fruit,
coffee and tea stains.
Insufficient amounts of
detergent were used.
The laundry was heavily
soiled with grease.
– Use the powder detergent
container instead of the
liquid detergent container
or
– add a little stain remover to
the laundry in the drum.
– Select the highest degree
of soiling and use liquid
detergent.
–
Before washing the next
load, run a Cottons 60°C
programme with liquid
detergent but without a
load.
18
Problem solving guide
White residues which
look like powder
detergent are seen on
dark textiles after
washing.
General problems
Dark spots are visible
in the liquid detergent.
The detergent
contained compounds
(zeolites) to aid water
softening which are not
soluble in water. These
have stuck to fabrics.
Mould has formed in
the liquid detergent.
Try and brush off the
–
residues with a soft brush
once the laundry is dry.
Wash dark textiles using a
–
detergent which contains
no zeolites. Liquid
detergents usually contain
no zeolites.
Use the Dark garments
–
programme.
Remove the liquid
–
detergent from the
container and clean it
thoroughly.
– Seal the liquid detergent
container with the cover to
prevent mould forming
again.
19
Alteration rights reserved/2211
M.-Nr. 07 917 340 / 00
Loading...