Miele w 4449 User Manual

Operating instructions
for Washing machine
W 4449 WPS LiquidWash

To avoid the risk of accidents or
damage to the machine it is
essential to read these instructions
before it is installed and used for the
first time.

en-GB

M.-Nr. 07 170 970

Caring for our environment

Disposal of the packing
material

The transport and protective packing
has been selected from materials which
are environmentally friendly for disposal
and can normally be recycled.

Ensure that any plastic wrappings,
bags etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation!

Rather than just throwing these
materials away, please ensure they are
offered for recycling.

Disposal of your old appliance
or machine

Electrical and electronic appliances /
machines often contain materials
which, if handled or disposed of
incorrectly, could be potentially
hazardous to human health and to the
environment. They are, however,
essential for the correct functioning of
your appliance or machine. Please do
not therefore dispose of your old
machine or appliance with your
household waste.

Please dispose of it at your local
community waste collection / recycling
centre or contact your Dealer for
advice. Ensure that it presents no
danger to children while being stored
for disposal.

It should be unplugged or disconnected
from the mains electricity supply by a
competent person.

2

Contents

Caring for our environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Operating the washing machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Control panel .....................................................10

Display ..........................................................11

Before using for the first time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Preparing the washing machine ......................................13

Priming the liquid detergent dispensing system ..........................14

Liquid detergent dispensing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

How automatic liquid detergent dispensing works ........................16

Dosage level .....................................................16

Useful tips .......................................................17

Washing environmentally and economically . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Energy and water consumption ....................................18

Detergent .....................................................18

How to wash correctly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Extra options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Short............................................................25

Water plus .......................................................25

Pre-wash ........................................................25

Further extras.....................................................25

Soak .........................................................25

Rinse hold .....................................................25

Extra rinse .....................................................25

Buzzer ..........................................................25

Spinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Final spin speed ..................................................26

Rinse and interim spin ...........................................26

To omit the final spin (Rinse hold) ..................................26

To omit rinse and interim spin and the final spin (No spin) ...............26

Delay start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Programme chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Programme sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Garment care label symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

3

Contents

Changing the programme sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Cancelling a programme ............................................36

Interrupting a programme ...........................................36

Changing a programme ............................................36

Adding or removing laundry after a programme has started ................37

Safety lock .......................................................37

Detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

The correct detergent ..............................................38

Water softeners.................................................39

Washing with several components ..................................39

Fabric conditioners and liquid starch ................................40

Colour run and dye removers/dyes .................................40

Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

External casing and fascia panel .....................................41

Extra cleaning ..................................................41

Cleaning the detergent dispenser drawer...............................41

Descaling the machine .............................................42

Cleaning the dispensing unit .........................................43

Cleaning the container and lid .....................................43

Cleaning the dispensing tube......................................43

Cleaning the filter in the water inlet ....................................44

Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

The programme does not start .......................................45

Fault messages in the display ........................................46

Problems with the automatic liquid detergent dispensing system ............47

General problems .................................................49

An unsatisfactory wash result ........................................50

The door will not open ..............................................51

Opening the drum door in the event of a blocked drain outlet and/or power failure

................................................................52

Blocked drain outlet .............................................52

After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Future updates (PC) .............................................54

Appliance guarantee ............................................54

Optional accessories ............................................54

4

Contents

Installation and connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Front view........................................................55

Rear view ........................................................56

Installation surface.................................................57

Transporting the machine to its installation site ........................57

Removing the transit fittings .........................................57

Re-fitting the transit bars ............................................59

Levelling the machine ..............................................60

Washer-dryer stack..............................................61

Dispensing unit ...................................................62

The Miele Waterproof system ........................................65

Connection to the water supply .......................................66

Connection to the drainage system....................................68

Electrical connection U.K. ...........................................69

Consumption data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Notes for test institutes: ..........................................70

Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Settings menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

To open the Settings menu........................................73

Language F......................................................73

Time (of day) .....................................................73

Detergent dosage .................................................74

Gentle action .....................................................74

Longer pre-wash ..................................................74

Suds cooling .....................................................74

Lock code .......................................................75

Temperature unit ..................................................76

Buzzer ..........................................................76

Keypad tone .....................................................76

Brightness .......................................................76

Contrast .........................................................76

Standby display ...................................................77

Memory .........................................................77

Anti-crease.......................................................77

Optional accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

CareCollection ....................................................78

5

Warning and Safety instructions

This washing machine is not
This washing machine conforms to
current safety requirements.
Inappropriate use can, however,
lead to personal injury and damage
to property.

To avoid the risk of accidents and
damage to the washing machine,
please read these instructions
carefully before using it for the first
time. They contain important
information on its installation, safety,
use and maintenance.
Keep these instructions in a safe
place and ensure that new users are
familiar with the content. Pass them
on to any future owner.

Correct application

This washing machine is for

~

domestic use only and can only be
used to wash items which are specified
by the manufacturer to be
machine-washable on the wash care
label, and textiles composed of
hand-washable wool or wool blend
fabrics as well as satin, lace, silk and
other hand-washable garments.
Any other applications may be
dangerous. Miele cannot be held liable
for damage resulting from incorrect or
improper use or operation.

~

intended for use by persons (including
children) with reduced physical,
sensory or mental capabilities, or lack
of experience and knowledge, unless
they are supervised whilst using it or
have been shown how to use it by a
person responsible for their safety.

Safety with children

Keep children away from the

~

washing machine at all times. It is not a
toy! To avoid the risk of injury do not
allow children to play on or near it or to
play with its controls. Supervise
children whilst you are using it.

Older children may only use the

~

washing machine if its operation has
been clearly explained to them and
they are able to use it safely,
recognising the dangers of misuse.

For machines with a 'porthole' door,

~

remember that the porthole glass will
be hot when washing at very high
temperatures.
Do not let children touch it.

6

Warning and Safety instructions

Technical safety

Before setting up the washing

~

machine, check it for any externally
visible damage.
Do not install or use a damaged
washing machine.

Before connecting the washing

~

machine, ensure that the connection
data on the data plate (voltage and
connected load) match the mains
electricity supply. If in any doubt,
consult a qualified electrician.

The electrical safety of this washing

~

machine can only be guaranteed when
continuity is complete between it and
an effective earthing system which
complies with current local and national
safety regulations. It is most important
that this basic safety requirement is
present and regularly tested, and
where there is any doubt the household
wiring system should be inspected by a
qualified electrician. The manufacturer
cannot be held liable for the
consequences of an inadequate
earthing system (e.g. electric shock).

Do not connect the washing

~

machine to the mains electricity supply
by an extension lead. Extension leads
do not guarantee the required safety of
the appliance (e.g. danger of
overheating).

Faulty components must only be

~

replaced by genuine Miele original
spare parts. Only when these parts are
fitted can the safety standards of the
machine be guaranteed.

Unauthorised repairs could result in

~

unforeseen dangers for the user, for
which Miele cannot accept liability.
Repairs should only be undertaken by a
Miele approved service technician.
Ensure current is not supplied to the
machine until after maintenance or
repair work has been carried out.

If the connection cable is faulty it

~

must only be replaced by a Miele
approved service technician to protect
the user from danger.

In the event of a fault or for cleaning

~

purposes, the washing machine is only
completely isolated from the electricity
supply when:
– it is switched off at the wall socket

and the plug is withdrawn, or
– it is switched off at the mains, or
– the mains fuse is withdrawn, or the

screw-out fuse is removed (in

countries where this is applicable).

The Miele "Water protection system"

~

protects from water damage provided
the following conditions have been met:
–

the machine is correctly plumbed in

and connected to the electricity

supply.
–

if a fault has been identified, the

machine must be examined by a

competent person before further use,

and repaired if necessary.

In countries where there are areas

~

which may be subject to infestation by
cockroaches or other vermin, pay
particular attention to keeping the
machine and its surroundings in a
clean condition at all times. Any
damage which may be caused by
cockroaches or other vermin will not be
covered by the machine guarantee.

7

Warning and Safety instructions

This washing machine may only be

~

used in mobile installations such as
ships if a risk assessment of the
installation has been carried out by a
suitably qualified engineer.

Do not make any alterations to the

~

washing machine, unless authorised to
do so by Miele.

Correct use

Do not install your washing machine

~

in rooms where temperatures below
freezing may occur. Frozen hoses may
burst or split. The reliability of the
electronic control unit may be impaired
at temperatures below freezing point.

Before using the washing machine

~

for the first time, check that the transit
bars at the rear of the machine have
been removed (see section on
"Installation"). During spinning, a transit
bar which is still in place may result in
damage to both the machine and
adjacent furniture or appliances.

Turn off the stopcock if the machine

~

is to be left for any length of time (e.g.
holiday), especially if there is no floor
drain (gully) in the immediate vicinity.

Flooding danger.

~

If hooking the drain hose into a wash
basin, check that the water can drain
off quickly enough to prevent the sink
from overflowing. Make sure the drain
hose is secure, so that the force of the
water flowing out of the hose does not
dislodge it.

Take care to ensure that foreign

~

objects (e.g. nails, pins, coins, paper
clips) do not find their way into the
machine with the laundry. These may
damage components of the machine
(e.g. suds container, drum), which in
turn can result in damage to the
laundry.

If the correct amount of detergent is

~

dispensed, the machine should not
need to be descaled. If, however, you
do wish to descale the machine only
use proprietary non-corrosive descaling
agents and strictly observe the
instructions on the packaging. A
special descaling agent is available to
order from the Miele Spare Parts
Department or via the internet on
www.miele-shop.com.

8

Warning and Safety instructions

Textiles which have been

~

pre-treated in solvent based cleaning
agents must be thoroughly rinsed in
clean water before being washed in the
machine.

Never use solvent based cleaning

~

agents, e.g. those containing benzene,
in this machine, as this may result in
damage to component parts and create
toxic fumes. Such agents also pose a
fire and explosion hazard.

Never use solvent based cleaning

~

agents, e.g. those containing benzene,
to clean the outside surfaces of this
machine. They can cause damage to
plastic surfaces.

Only use dyes specified by the

~

manufacturer as being suitable for use
in a domestic washing machine. Always
observe the manufacturer's instructions
carefully.

Colour run and dye removers

~

contain sulphur compounds which can
cause damage such as corrosion. Do
not use these products in this machine.

Only remove laundry from the

~

washing machine once the drum has
stopped turning. Reaching into a
moving drum is extremely dangerous
and could result in injury.

Accessories

Accessory parts may only be fitted

~

when expressly approved by Miele. If
other parts are used, guarantee,
performance and product liability
claims will be invalidated.

Miele cannot be held liable for
damage caused by non-compliance
with these Warning and Safety
instructions.

If liquid detergent comes into

~

contact with the eyes, rinse them
thoroughly with lukewarm water imme
diately. If swallowed, seek medical
assistance immediately and retain the
packaging or label for reference. Those
with skin problems or sensitive skin
should avoid their skin coming into
contact with liquid detergent.

-

9

Operating the washing machine

Control panel

a Programme buttons

For selecting a washing programme.

b Display with Menu buttons

See the next pages for more
information.

c PC / Optical interface

This is used by service technicians
to run diagnostic checks on your
machine and can also be used to
update programming data in the
future.

d Extra option buttons

Various extra options can be added
to the washing programmes.

e Delay start button

For delaying the start time of a
programme.

f Start/Stop button

For starting the programme once it is

selected or calling up the Stopped:

menu to cancel a programme.

g Buzzer button

An audible tone sounds at the end of

the programme.

h Automatic dispensing button

Activates the automatic dispensing

of liquid detergent.

i I-On/0-Off button

For switching the machine on or off.

j Door button

Opens the machine door.

10

Operating the washing machine

Display

The display is used for the following:

Selecting and displaying settings

Temperature

–

Spin speed

–

Soak duration

–

Delay start

–

Cancelling a programme

–

Safety lock

–

Estimated programme duration

–

Selecting programmes via the
display

By pressing the Further programmes
button, you can select one of the
following programmes:

Denim

–

Hygiene

–

Dark garments

–

Curtains

–

Pillows

–

Silks /

–

– Sportswear

– Outerwear

– First wash

– Proofing

– Drain / Spin

– Separate rinse

– Starch

Selecting extra options via the
display

By pressing the Further extras button,
you can select (depending on the
programme) the following extra options:

–

Soak

–

Rinse hold

–

Extra rinse

11

Operating the washing machine

Menu buttons

Various settings are made via the Menu
buttons.

They are used to alter or confirm the
value displayed above the vertical line.

To alter a setting:

Cottons

Duration:

60°C

1:49 h

1600 rpm

Pressing the left hand Menu button
under 60°C alters the temperature and
pressing the right hand Menu button
under 1600 rpm alters the spin speed.

To confirm a setting:

Further programmes

Denim

Continue

OK

Pressing the left hand Menu button
under Continue calls up further
programmes, and you can then confirm
your selection of the highlighted
programme by pressing the right hand
Menu button under OK.

12

Before using for the first time

Preparing the washing
machine

Before using the machine for the first
time ensure that it is correctly
installed and connected. See
"Installation and connection". Also
check that the drain filter is securely
tightened to prevent the risk of water
leaks during use.

This washing machine has
undergone a thorough functional test
in the factory and there will be some
residual water in the drum from this
process.

^ Press the I-On/0-Off button in.

If the washing machine is being
switched on for the first time, the
welcome screen will appear.

The welcome screen will appear in the
display every time the machine is
switched on until a programme lasting
longer than 1 hour has been
completed.

The display for setting the language will
then appear.

Setting the language

You will be asked to select the
language you require for the display. It
is possible to change the language at
any time via the Settings menu.

Sprache

deutsch

) OK

If the language shown is not the one

^

you want, select the language you do
want by pressing the left hand Menu

button under ). Confirm your

selection by pressing the right hand

Menu button under OK.

Setting the time of day

The display for setting the time will then
appear.

12:00

Change

OK

^ Select the hours you want by pressing

the left hand Menu button under
Change, and confirm this with the
right hand Menu button under OK.

^ Then set and confirm the minutes.

Reminder to remove transit bars

To avoid the risk of damage, the
transit bars must be removed before
the machine is used for the first time.
See "Installation and connection" for
instructions on how to do this.

^

After removing the transit bars (if this
has not already been done by your
fitter) press the right hand Menu
button under OK.

Reminder to remove the dispensing
unit

^

Open the door and remove the
dispensing unit (liquid detergent
container).

^

Confirm that you have removed the
dispensing unit by pressing the right
hand Menu button under OK.

13

Before using for the first time

For safety reasons, spinning is not
possible until the machine has been
set up for using for the first time. To
activate the spinning function you
must run a wash programme without
laundry.
This will also fill the dispensing
system tube with liquid detergent.

Priming the liquid detergent
dispensing system

See "Installation and connection ­Dispensing unit" for instructions on
how to install and connect the
dispensing unit.

Add liquid detergent up to a

^

maximum of 1 cm below the top rim
(approx. 5 litres).

Close the lid so that the liquid

^

detergent does not dry out and to
prevent any foreign objects getting
into the container.

Place the container back on its base

^

and press it down firmly to open the
valve in the bottom.

Filling the dispensing tube with
detergent

^ Press the Delicates programme

button.

Delicates

,The container is designed for

liquid detergent only. Filling it with
other agents, e.g. bleaching agents
or powder detergent will damage
the washing machine and/or the
laundry.

Adding detergent

^

Lift the container off its base, if
necessary.

The container has a valve in the bottom
which closes automatically when it is
removed from its base.

^

Open the lid of the container.

Duration:

40°C

0:59 h

600 rpm

^ Press the left hand Menu button

under 40°C.

Delicates

Duration:

30°C O O F F F

^

Press the left hand Menu button

0:59 h

600 rpm

repeatedly until 60°C appears.

Delicates

Duration:

60°C

1:19 h

600 rpm

14

Before using for the first time

Press the Automatic dispensing

^

button.

Normal soiling

0 00ml

* OK

Enter a dosage of 100 ml. Enter the

^

first number with the left hand Menu

button under *. Confirm your

selection of this number by pressing
the right hand Menu button under
OK. Now enter the second number.

Repeat this process until all three

^

numbers have been entered.

The display will change to show the
degree of soiling.

Degree of soiling

Normal

Continue

Q Q H HM

OK

^ Use the left hand Menu button under

Continue to select Very heavy and
confirm this with the right hand Menu
button under OK.

At the end of the programme, the

^

washing machine and dispensing
system are ready for use.

There may still be air bubbles in the
dispensing tube. However these will
not affect the functioning of the
system.

Switch off the washing machine.

^

After the washing machine and
liquid detergent dispensing system
have been prepared for use, you will
need to set the dosage level

recommended by the
manufacturer of the detergent you

are using, see the following page.

^

Press the Start/Stop button.

The dosage you have set here only
applies to priming the liquid
detergent dispensing system. You
will need to set the dosage level to
that recommended by the
manufacturer of the detergent you
are using.

15

Liquid detergent dispensing

How automatic liquid
detergent dispensing works

If you start a programme using auto
matic dispensing, the washing machine
will calculate how much detergent to
dispense according to the dosage level
set, the amount of laundry in the drum
and the degree of soiling specified.
This means that the correct amount of
detergent for the load will be dispensed
automatically.

If the Pre-wash extra option has been
selected, the washing machine will
automatically divide the amount of
detergent to be dispensed into the
correct proportions for the pre-wash
and the main wash.
the pre-wash and

1

/3will be used for

2

/3for the main wash.

-

Dosage level

Follow the manufacturer's
recommendation for normally soiled
laundry given on the packaging.

The water hardness level of the local
water supply must also be taken into
account.

Setting the dosage level

^

Close the drum door.

Press both menu buttons at the same

^

time until the following appears in the
display:

Settings

Language !

Continue

OK

You are now in the Settings menu.

Press the left hand Menu button

^

under Continue until the Detergent
dosage setting appears and confirm

your selection of this by pressing the
right hand Menu button under OK.

Normal soiling

1 00ml

* OK

^ Now enter the dosage level required,

e.g. for 90 ml, enter the numbers 090.

^ Enter the first number with the left

hand Menu button under *. Confirm

your selection of this number by
pressing the right hand Menu button
under OK. Now enter the other
numbers.

Your machine has now been set up for
automatic detergent dispensing.

^

Switch on the washing machine.

16

Liquid detergent dispensing

Useful tips

The correct liquid detergent

You can fill the container with any
brand of liquid detergent. However, it is
advisable to fill it with the brand you
tend to use most frequently.

Make a note of the brand name of the
liquid detergent below to remind you of
the name when you need to buy some
more.

Brand name

Refilling

If you want to continue using the same
brand of liquid detergent, you can
simply refill the container, in which case
it is not necessary to clean it out.

Filling the container with a different
brand

Do not mix brands of liquid
detergent. This can give a poor
wash result and cause the detergent
to separate.

Clean the container as described in

^

"Cleaning and care".

Make sure you alter the dosage level

^

if a different dosage to the previous
one set is recommended by the
manufacturer.

Degrees of soiling

Light

:
No visible dirt or stains. Possibly slight
body odour.

Normal:
Visibly dirty and/or just a few slight
stains.

Heavy:
Stains and soiling clearly visible.

Very heavy:
Stains and soiling clearly visible which
have been there for a while and dried
on.

17

Washing environmentally and economically

Energy and water consumption

Water consumption and energy

–

usage are determined by the size of
the load.
To make the most out of your
machine, load the maximum dry load
for the programme you are using.

Use the Automatic and Express

–

programmes for small loads.

When smaller amounts of laundry are

–

washed using the Cottons
programme, the automatic load
recognition system will reduce the
amount of water, time and energy
used. This may mean that the time
left shown in the display is adjusted
during the course of the wash
programme.

– Using the Cottons 60°C programme

instead of the Cottons 95°C
programme will give energy savings
of between 35% and 45%. This is
sufficient for most levels of soiling.
For stubborn or old stains, use the
Soak extra option.

Detergent

Do not exceed the amounts of

–

detergent recommended by the
manufacturer on the packaging.

Adjust the dosage to the degree of

–

soiling of the laundry.

Use Automatic dispensing.

–

Choosing the correct Extra option
(Short, Soak, Pre-wash)

Select:

A wash programme together with the

–

Short extra option for light to normal
soiling where there are no obvious
marks.

– A wash programme without any extra

options for normal to heavy soiling
with visible staining.

– A wash programme together with the

Soak extra option for heavily soiled
laundry.

–

The Pre-wash extra option for laundry
with large amounts of dirt (e.g. dust,
sand).

18

When drying with a tumble dryer

–

Selecting the highest possible spin
speed for the wash programme will
save energy when drying in a tumble
dryer afterwards.

Brief instructions

The headings numbered A, B, C,...
show the operating sequence and can
be used as brief instructions.

A Sort the laundry

^ Empty all pockets.

,

Foreign objects (e.g. nails,
coins, paper clips, etc.) can cause
damage to garments and
components in the machine.

^

Badly soiled areas, stains etc. should
be cleaned as soon as possible,
preferably whilst still fresh. Spillages
should be carefully dabbed off using
a soft colourfast cloth. Do not rub!

Badly soiled areas can be pre-treated
with liquid detergent, stain removers
etc. first, following the manufacturer's
instructions. With particularly stubborn
stains ask your dry cleaner for advice.

How to wash correctly

If you use a solvent-based clean

,

ing agent (e.g. one containing ben
zene) to pre-treat a stain, make sure
that any plastic parts (e.g. buttons)
are protected, and that the cleaning
agent is rinsed off before washing the
garment in the machine.

Do not use solvent-based

,

cleaning agents in this machine.

Sort the laundry by colour and by

^

care label. Most garments have a
textile care label in the collar or side
seam.

Dark textiles often contain excess dye
and should be washed separately
several times before being included in
a mixed load. Always wash whites and
coloureds separately.

– Curtains: Remove lead weights first

or place in a laundry bag.

–

Underwiring and collar stiffeners:
Any loose wiring in bras, shirt collar
stiffeners, etc. should be removed or
sewn in.

–

Knitted garments, trousers and
jeans, T-shirts and sweat shirts: Turn
inside out, if recommended by the
manufacturer.

–

Close any zips, fasten hooks and
eyes etc before washing.

–

Fasten duvet covers etc. to prevent
small items from being rolled up
inside them.

Do not wash any items in this machine
which are specified by the
manufacturer as not washable on the
care label. (h symbol)

-

-

19

How to wash correctly

B Switch on the washing machine

The interior drum lighting will come on.

C Load the drum

Press the Door button to open the

^

drum door.

Unfold the laundry and load loosely

^

in the drum. Mixing both large and
small items gives better wash results
and also helps distribute the load
evenly during spinning.

The most efficient use of energy and
water is achieved when a full load is
washed. However, do not overload as
this causes creases and reduces
cleaning efficiency.

Make sure that no garments are
caught between the drum door and
seal.

D Select a programme

^ The programmes are selected with

the programme buttons.

The relevant indicator light will come on
to show which programme has been
selected.

The programme selected will also
appear in the display.

Cottons

^

Shut the door with a gentle swing.

20

Duration:

60°C

1:49 h

1600 rpm

You can now set the temperature and
spin speed you want via the Menu
buttons.

Cottons

How to wash correctly

Duration:

60°C

By pressing the left hand Menu

^

1:49 h

1600 rpm

button under 60°C you can alter the
temperature, and by pressing the
right hand Menu button under 1600
rpm you can alter the spin speed.

Pressing the Further programmes
button calls up a list of additional
programmes.

Further programmes

Denim

Continue

OK

^ Pressing the left hand Menu button

under Continue calls up the further
programmes, and you can then
confirm your selection of the
highlighted programme by pressing
the right hand Menu button under
OK.

Denim

Select any extra options by pressing

^

the appropriate button. The relevant
indicator light will come on to show
which extra option has been
selected.

^ Press the Further extras button to

select the following extra options
(depending on the programme
selected): Soak, Rinse hold and Extra
rinse.

Not all the extra options are suitable for
use with every programme.

You can only select extra options
which are compatible with the basic
programme being used.

Duration:

40°C

^

You can then alter the temperature

1:00 h

900 rpm

and spin as described above for this
programme.

21

How to wash correctly

E Add detergent

Too little detergent results in:

Laundry not getting properly clean

–

and with time it may become grey
and hard to the touch.

Greasy particles clinging to the

–

laundry.

Limescale deposits on the heater

–

elements.

Too much detergent results in:

Excessive foam which causes a low

–

level of agitation and poor wash,
rinse and spin results.

– High water consumption (an

additional rinse cycle will
automatically switch in).

– A burden to the environment.

See "Detergent" for further information.

Automatic dispensing of liquid
detergent

^ Press the Automatic dispensing

button.

The degree of soiling will appear in the
display:

Degree of soiling

Normal

Continue

Q Q H HM

OK

22

^

By pressing the left hand Menu
button under Continue you can alter
the degree of soiling and you can
confirm your selection by pressing
the right hand Menu button under
OK.

Amount of liquid detergent will now be
dispensed for the programme.

See "Liquid detergent dispensing" for
more information.

How to wash correctly

Detergent dispensing drawer

If you want to run a programme using
powder detergent or special
application agents, these should be
added to the detergent dispensing
drawer.

Please note:

If using powder detergent or special

–

application agents, do not

press the
Automatic dispensing button, as this
will cause too much detergent to be
dispensed.

Close the detergent drawer.

^

See "Detergent" for further information.

F Select Delay start (if required)

Press the Delay start button to set the

^

time you wish to programme to end
at.

See "Delay start" for more information.

G Start the programme

Press the flashing Start/Stop button.

^

If a delay start time has been set, then
this will count down in the display. At
the end of the delay start time or imme­diately after the programme has started
(if no delay start time has been
selected) the estimated programme
duration will appear in the display.
During the first 8 minutes the machine
measures how much water is being
absorbed by the laundry. The
programme duration may be longer or
shorter depending on this absorbency
rate.

^

Pull out the detergent drawer and
add detergent to the compartments
as follows:

i

Detergent for the pre-wash (divide
the total recommended amount as
follows: add

2

and

/3to compartment j)

1

/3to compartment i

j

Detergent for the main wash,
including Soak if selected

§

Fabric conditioner or liquid starch

The programme sequence is also
shown in the display. The machine lets
you know which section of the
programme has been reached.

The drum lighting switches off once the
programme has started.

23

How to wash correctly

H Remove the laundry when the

programme has finished

In the anti-crease phase after the
programme has finished, the following
will appear alternately in the display:

Cottons

Anti-crease

60°C

1600 rpm

and

Cottons

Finish

60°C

1600 rpm

^ Press the Door button to open the

drum door.

^ Remove the laundry.

Check that all items have been
removed from the drum. Items left in
the drum could discolour other items
in the next wash or become
discoloured themselves.

Check the folds in the door seal for

^

any small articles, e.g. buttons, which
might be lodged there.

^ Switch the machine off with the

I-On/0-Off button.

^ Close the drum door. Otherwise there

is the danger of objects being placed
inadvertently in the drum. If these
remained unnoticed and were
washed in the next load, they could
damage the laundry.

24

Extra options

Short

For light to nomal soiling with no visible
staining.

The duration of the main wash is
reduced.

Water plus

The water level in the main wash and
the rinses will be increased if the Water
plus option is selected.

Pre-wash

For laundry with large amounts of dirt
e.g. dust, sand.

Further extras

Soak

For heavily soiled and stained items
with protein stains (e.g. blood, fats and
oils, cocoa).

A length of time of between 30 minutes
and 6 hours can be chosen, in 30
minute increments, for the "Soak"
process.

–

To select the soak duration

^

Press the Further extras button.

Further extras

8 Soak

You can now use the display to select
the soak time you require.

Soak duration

Duration: 0:30 h

Increase

Each time the left hand Menu button

^

OK

under Increase is pressed, the soak
duration is increased by 30 minutes.
Confirm the duration required by
pressing the right hand Menu button
under OK.

Further extras

9 Soak

Continue

OK

^ Press the left hand Menu button

under Continue until Back appears
in the display and confirm this with
the right hand Menu button under

OK.

– To delete the soak time

^

Press the Further extras button, and
then the right hand Menu button
under OK to switch off Soak.

Rinse hold

See the next page.

Extra rinse

An additional rinse cycle is carried out
to achieve a better rinse result.

Continue

^

Select Soak and press the right hand

OK

Menu button under OK.

Buzzer

An audible tone sounds repeatedly at
the end of a programme and when
Rinse hold is reached. The buzzer will
sound repeatedly until the machine is
switched off. The volume of the buzzer
can be changed; see "Settings menu".

25

Spinning

Final spin speed

Programme rpm

Cottons 1600

Minimum iron 1200

Delicates 600

Woollens 1200

Automatic 1200

Shirts 600

Express 1600

Denim 900

Hygiene 1600

Dark garments 1200

Curtains 600

Pillows 1200

Silks 400

Sportswear 1200

Outerwear 800

First wash 1200

Proofing 1000

Drain / Spin 1600

Separate rinse 1200

Starch 1500

You can reduce the final spin speed.
However, you cannot select a final spin
speed higher than that shown in the
chart above.

Rinse and interim spin

There is a spin after the main wash and
between the rinses. A reduction in the
final spin speed will also reduce the
interim spin speed. If a spin speed of
less than 700 rpm is selected in the
Cottons and Hygiene programmes, an
additional rinse is introduced.

To omit the final spin (Rinse hold)

Press the Further extras button and

^

select the Rinse hold setting. The
laundry will not be spun and will
remain suspended in the final rinse
water. This reduces creasing if the
laundry is not going to be removed
from the drum immediately after the
end of the programme.

To start the final spin

–

:

The washing machine will display the
maximum spin speed possible. You
can select a spin speed lower than
this. Start the final spin by pressing
the Start/Stop button.

– To end the programme

:

Press the Door button. The water will
drain away. Press the Door button
again to open the door.

To omit rinse and interim spin and
the final spin (No spin)

^

Select No spin u from the spin
speed menu. The laundry is not spun
after the final rinse. The water will
drain away and the machine will go
straight into the anti-crease stage.
An additional rinse is introduced if
this setting is selected with the

Cottons, Minimum iron, Automatic,
Express and Hygiene programmes.

26

Delay start

With delay start you can choose when
you want the programme to end. The
start of a programme can be delayed
from 30 minutes up to a maximum of
24 hours, allowing you to make use of
night-time economy electricity rates, for
example.

The current time of day needs to
have been set for delay start to work
correctly.

To select delay start

A After selecting the programme, press

the Delay start button.

The display shows the start time: from
xxx, the time for the programme to end:
to xxx, and the current time.

Delay start 9:05

from 9:05 to 10:49

Change

Back A

The first press on the button will adjust
the programme end time to the next
half or full hour. Each subsequent press
on the button will change the
programme end time by 30 minutes.

Delay start 9:05

from 16:16 to 18:00

Change

OK

C Confirm the time you require by

pressing the right hand Menu button
under OK.

To begin delay start

D Press the Start/Stop button.

Cottons

Start in:

60°C

7:11 h

1600 rpm

The display will show how long until the
programme starts. It will count down
and start automatically when the delay
start time has elapsed.

The estimated programme duration will
then appear in the display.

The actual load size can only be
determined accurately by the
machine once the programme has
started. The programme end time
may, therefore, be a bit later or
earlier than first indicated.

B Use the left hand Menu button under

Change to select the time you want
the programme to end at.

27

Delay start

To alter delay start

You can subsequently select a later
programme end time if you wish.

Press the Delay start button.

^

Delay start 9:05

from 16:16 to 18:00

Change

Use the left hand Menu button under

^

OK

Change to alter the time you want the
programme to end at.

Confirm by pressing the right hand

^

Menu button under OK.

To delete delay start

You can delete the delay start time and
start the selected programme straight
away.

^ Press the Delay start button.

Delay start 9:05

To cancel delay start

Press the Start/Stop button.

^

The following will appear in the display:

Stopped:

Cancel delay start

Continue

Confirm by pressing the right hand

^

OK

Menu button under OK.

Now you can select a different

^

programme, or

^ Press the Start/Stop button to start

the programme straight away.

from: 16:16 to: 18:00

Change

^

Press the right hand Menu button

Delete

under Delete.

^

Press the Start/Stop button to start
the programme straight away.

28

Programme chart

Cottons 98E76* 30°C to 95°C Max. load 6.0 kg

Fabric Cottons, linens or cotton mix fabrics, e.g. table linen, towelling,

underwear, T-shirts etc.

Extra options Pre-wash, Soak, Short, Water plus, Rinse hold, Extra rinse

Note for test institutes:

Short programme: 3.0 kg load and Short extra option

Minimum iron
43218E76*

Fabric Synthetics, mixed fibres and easy care cottons. If fabrics have a

high proportion of man-made fibres, it is advisable to programme
the machine for "Gentle action". See "Settings menu".

Note Reduce the spin speed for fabrics which crease easily.

Extra options Pre-wash, Soak, Short, Water plus, Rinse hold, Extra rinse

Delicates 4321ac* cold to 60°C Max. load 2.0 kg

Fabric For delicate garments made of synthetic fibres, mixed fibres,

rayon and easy care cottons.

Extra options Pre-wash, Soak, Short, Rinse hold

Woollens /ac* cold to 40°C Max. load 2.0 kg

Fabric Machine-washable or hand-washable wool or wool blend fabrics.

If the care label does not specify a temperature, wash using the
cold setting.

Extra option Rinse hold

Automatic 7621* cold to 40°C Max. load 3.5 kg

Fabric Mixed loads of garments suitable for the Cottons and Minimum

iron programmes. Sort according to colour.

Note The wash parameters (e.g. water level, wash rhythm and spin

speed) are adjusted automatically in this programme to ensure
the best possible care and wash result for each item.

Extra option Rinse hold

30°C to 60°C Max. load 3.0 kg

29

Programme chart

Shirts cold to 60°C Max. load 2.0 kg

Notes

Extra options Short, Water plus, Rinse hold

Express 76* cold to 40°C Max. load 3.0 kg

Fabric Small loads of items which require freshening up and which can

Extra options Water plus, Rinse hold, Extra rinse

Denim cold to 60°C Max. load 3.0 kg

Notes

Extra options Pre-wash, Soak, Short, Rinse hold

Hygiene 8* 60°C Max. load 6.0 kg

Fabric Fabrics which will be in direct contact with the skin, e.g.

Note There is a longer temperature holding time in the main wash.

Extra options Pre-wash, Soak, Water plus, Rinse hold, Extra rinse

Dark garments cold to 40°C Max. load 3.0 kg

Item Dark garments made from cotton or mixed fibres.

Note Wash inside out.

Extra options Short, Rinse hold

Pre-treat collars and cuffs if necessary.

–

Wash silk garments in the Silks programme.

–

be washed in a Cottons programme.

Wash denim inside out.

–

Denim often contains excess dye and will run during the first

–

few washes. Wash light and dark coloured items separately.

underwear, nappies, towelling, bed linen, pillow and mattress
covers.

30

Programme chart

Curtains cold to 40°C Max. load 2.0 kg

Item Curtains, including net curtains, specified as machine-washable

by the manufacturer. A pre-rinse without detergent is carried out
automatically to remove dust.

Note For curtains which crease easily, reduce the spin speed or

deselect it.

Extra options Water plus, Rinse hold

Pillows 40°C to 60°C 2 pillows (40 x 80 cm) or

1 pillow (80 x 80 cm)

Item Washable pillows with feather, down or synthetic fillings.

Note Please observe the instructions on the wash care label.

Extra options Water plus, Rinse hold

Silks /c* cold to 30°C Max. load 1.0 kg

Fabric Silks and other handwashable fabrics with no wool content, e.g.

satin, lace and silk.

Note Place tights, bras etc. in a washing bag.

Extra options Water plus, Rinse hold, Extra rinse

Sportswear 30°C to 60°C Max. load 2.0 kg

Item Lightly soiled sports garments which require washing or

freshening up.

Extra options Pre-wash, Soak, Short, Water plus, Rinse hold

Outerwear cold to 40°C Max. load 2.0 kg

®

Item Outerwear made from micro-fibres such as Gore-Tex

®

, WINDSTOPPER®etc.

Notes

SYMPATEX

–

Zip up jackets before washing.

–

Do not use fabric conditioner.

Extra options Pre-wash, Soak, Short, Water plus, Rinse hold

,

31

Programme chart

First wash cold to 40°C Max. load 3.0 kg

Fabric New items made of cotton, towelling and polyester fabrics.

Note Use this programme to wash any chemical residues out of new

items.

Extra options Water plus, Rinse hold

Proofing 40°C Max. load 2.0 kg

Item For treating microfibre fabrics, skiwear, fine, closeweave cotton

garments (poplin) or tablecloths to provide a water and dirt
resistant finish.

Notes The items should be freshly laundered and spun or dried before

proofing.
For best results, the items should be heat-treated afterwards,

either in a tumble dryer or by ironing.

Extra option Rinse hold

Drain / Spin Max. load 6.0 kg

Notes Drain only: Select No spin u.

Make sure you select the appropriate spin speed.

Separate rinse Max. load 6.0 kg

Extra option Rinse hold

Starch Max. load 6.0 kg

Note The laundry (table cloths, napkins, overalls) should be washed

but not treated with fabric conditioner.

Extra option Rinse hold

* Please note that the "buckets" represent garment care label symbols. See

"Garment care label symbols".

32

Programme sequence

Main wash Rinses Spinning

Water

level

Cottons d a ( 2-4
Minimum iron ( c e 2-3
Delicates e d e 3 – L
Woollens e e e 2 LL
Automatic ( abc e 2-3
Shirts e c e 2 – L
Express d b d 2-3
Denim ( c e 3 – L
Hygiene d b ( 3-4
Dark garments ( b d 3 LL

Curtains

Pillows

1)

2)

( d d 3 – L
( d e 3 – L

Silks e e e 2 – L
Sportswear d c d 2 LL
Outerwear e d e 3 L
First wash d b ( 2 LL
Proofing ( d –––L
Drain / Spin – – –––L
Separate rinse ––e 2 – L
Starch ( c –––L

Wash

rhythm

Water

level

Rinses Interim

spin

3)4)

5)

5)

5)

4)

LL
LL

LL

LL

LL

6)

Final

spin

L

d = Low water level
( = Medium water level
e = High water level

a= Intensive rhythm
b= Normal rhythm
c= Gentle rhythm
d= Sensitive rhythm
e= Handwash rhythm

See the following page for more information about the programme sequences.

33

Programme sequence

This machine has fully electronic
controls with automatic load
recognition. It takes in the right amount
of water required for the programme
depending on the amount of laundry
and its absorbency rate. This means
that programme cycles and durations
can vary.

The programme sequences outlined in
the chart are based on the basic
programme with a full load. Extra
options which can be selected have not
been taken into account.

The display shows the stage the
programme has reached.

Special features in the programme
sequences:

Anti-crease:

At the end of every programme, with
the exception of the Woollens
programme, the drum continues to turn
at intervals for up to 30 minutes to help
prevent creasing. The door can be
opened and laundry removed at any
time during the anti-crease phase.

1)

Pre-rinse: A pre-rinse without
detergent is carried out automatically
to remove dust.

2)

Run-up to spin: A run-up to spin is
carried out before the wash process
begins to deflate the pillows.
Subsequent water intake for the main
wash is through compartment j.

3)

A second rinse is carried out when a
temperature of 60°C to 95°C has
been selected. A third rinse is
carried out when a temperature
below 60°C is selected.

4)

A third or fourth rinse is carried out if:

34

–

there is too much foam in the drum

–

a spin speed lower than 700 rpm has
been selected

–

No u has been selected

5)

A third rinse is carried out if:

–

No u has been selected

6)

In the Outerwear programme,
laundry is only spun after the main
wash.

Garment care label symbols

Washing

The figure quoted in the bucket is the
maximum temperature the garment
can be washed at. The number of
bars under the symbol indicates the
level of agitation permitted.

9 No bar under the symbol: =

normal agitation

4 One bar under the symbol: =

reduced agitation

c Two bars under the symbol: =

much reduced agitation

/ Hand wash (if no temperature

is specified use the lowest
temperature or cold)

h Do not wash

Drying

The number of dots indicates the
drying temperature

q Normal temperature
r Low temperature
s Do not tumble dry

Ironing

The number of dots indicates the
ironing temperature

I Hot iron (max sole plate temp.

approx. 200°C)

H Medium hot iron (max sole

plate temp. approx. 150°C)

G Cool iron (max sole plate

temp. approx. 110°C). Do not
steam iron garments carrying
this symbol.

J Do not iron

Professional cleaning

f Dry clean only. The letters

indicate the type of cleaning

p

agent required.

w Professional Wet Clean only
D Do not dry clean

Bleaching

x Any oxidising bleaching

agent can be used

{ Only use an oxygen based

bleach or a non-chlorine
bleach

z Do not bleach

35

Changing the programme sequence

Cancelling a programme

You can cancel a programme at any
time after it has started.

Press the Start/Stop button.

^

Stopped:

Cancel programme

Continue

Press the right hand Menu button

^

under OK.

The suds will be pumped away.

If you want to remove the laundry:

^ Press the Door button.

If you want to select a different
programme:

^ Switch the machine off with the

I-On/0-Off button.

^ Switch the washing machine back on

again.

^

Check that there is still detergent in
the detergent drawer. Add detergent,
if necessary.

^

Select and start a new programme.

OK

Interrupting a programme

Switch the machine off with the

^

I-On/0-Off button.

To continue with the same programme:

Switch the machine back on with the

^

I-On/0-Off button.

Changing a programme

After the start of a programme it is no
longer possible to select a different
programme.

Temperature

It is possible to select a different
temperature up to 5 minutes after the
programme has started.

Spin speed

It is possible to change the spin speed
up until the final spin begins.

Extra options

It is possible to select or deselect the
Short and Water plus extra options up
to 5 minutes after the programme has
started.

36

It is not possible to make any
changes if the safety lock has been
activated.

Changing the programme sequence

Adding or removing laundry
after a programme has started

Press the Door button to open the

^

drum door.

Add or remove items.

^

Close the drum door.

^

The programme will continue
automatically.

Please note:

Once a programme has started the
machine cannot recognise any
adjustment to the load.

For this reason, if laundry is added or
removed after the start of a programme,
the machine will always complete the
programme cycle assuming a full load
which can lead to an increase in the
programme duration shown in the
display.

The door cannot be opened, if:

–

the suds temperature is above 55°C.

–

the water is above a certain level.

–

the programme has reached the
Final spin stage.

If you press the Door button when the
above conditions are present, the
following will appear in the display:

/ Door locked

Safety lock

The safety lock prevents the machine
from being opened or the
programme cancelled during a wash
programme.

To activate the safety lock

Press and hold in the Start/Stop

^

button after the programme has
started.

Stopped:

Cancel programme

Continue

By pressing the left hand Menu button
under Continue, the following will
appear in the display:

Activate safety lock

^ Confirm by pressing the right hand

Menu button under OK.

The following will appear in the display:

0 Locked

The safety lock is now activated. It is
deactivated automatically at the end of
the programme.

To deactivate the safety lock

^

Press the Start/Stop button.

The following will appear in the display:

Deactivate safety lock

^

Press the right hand Menu button
under OK, and then the following will
come up in the display:

1 Unlocked

OK

37

Detergent

The correct detergent

All modern detergents produced for automatic washing machines are suitable. Use dispensing aids,

e.g. balls, if these are supplied with the detergent. Tablets are suitable for full loads, but note that it

may be impractical to reduce tablets for smaller loads. Some tablets do not dissolve as rapidly as

others, and may not be suitable for programmes with short durations.

Do not use biological detergents on silk as the enzymes may damage the silk!

Instructions for use and recommended dosage amounts are given on the detergent packaging.

Liquid detergent should be dispensed using a ball provided by the manufacturer for programmes

without a pre-wash.

For programmes with a pre-wash you will need to purchase a special container from the Miele Spare
Parts department which sits in the main wash compartment j of the detergent dispenser drawer. Add
liquid detergent to this container for the main wash and to compartment i for the pre-wash.

All purpose detergent

for whites*

Cottons X X

Minimum iron X X

Delicates X

Woollens Liquid detergent for machine-washable woollens

Automatic X X

Shirts X X

Express X X

Denim X

Hygiene X

Dark garments X

Curtains X

Pillows X

Silks Liquid detergent for machine-washable silk and woollens

Sportswear X X

Outerwear X

First wash X X

Proofing Only use proofing agents which are stated by the manufacturer as being

Starch Liquid starch, starch formulations, viscous liquid starch, starch

1)

Only use liquid detergent

2)

Only use powder detergent or detergent specifically designed for washing curtains

* Powder detergent, tablet detergent, liquid detergent and liquid tab detergent.

"suitable for use on membrane textiles" as these consist of fluorochemical
compounds. Do not use proofing agents which contain paraffin. Add
proofing agents to compartment §.

2)

1)

Detergent for coloured

fabrics*

1)

1)

2)

X

1)

X

Detergent for delicates

38

Detergent

The right amount to dispense will
depend on the following:

The soiling level of the laundry

–

Lightly soiled
No visible dirt or stains. Possibly
slight body odour.

Normally soiled
Visibly dirty and/or just a few slight
stains.

Heavily soiled
Visible dirt and stains and/or dried on
soiling.

– The quantity of the laundry (use

Automatic dispensing).

– The water hardness level.

Check with your local water supplier
if you do not know the hardness level
in your area.

Water softeners

A water softener can be used to cut
down on the use of detergents in hard
water areas. Dispense according to the
amount specified on the packaging.
First add detergent and then the water
softener.

Use a quantity of detergent as for soft
water.
Miele do not recommend connecting
the machine to a household water
softener.

Washing with several components

If you wash using several components
(e.g. special application detergents),
we recommend always dispensing the
agents into compartment j in the
following order:

1. Detergent

2. Water softeners

3. Stain remover

This way the agents are distributed
more evenly.

39

Detergent

Fabric conditioners and liquid starch

Fabric conditioners make garments soft
to handle and help prevent static cling
when tumble drying.

Starch stiffens and gives body to items
of laundry, e.g. shirts, tablecloths and
bed linen.

Automatic dispensing of fabric
conditioner or liquid starch to
laundry at the end of a programme

If starching frequently, thoroughly
clean the dispenser compartment,
especially the siphon tube and
fabric conditioner channel, regularly.
See "Cleaning the detergent
dispenser drawer". Do not use
powder starch formulations or
viscous liquid starch in the §
compartment as it will clog up. See
below.

Adding fabric conditioner or starch
separately

^ Dispense in accordance with

manufacturer's instructions on the
packaging.

^ Add powder or viscous starch to

compartment i.

^ Add fabric conditioner or liquid

starch to compartment §.

^

Add the fabric conditioner or liquid
starch to compartment §. Do not

exceed the maximum level mark.

It will be automatically dispensed in the
last rinse. At the end of the programme
a small amount of water remains in the
fabric conditioner compartment §.

40

^ Press the Further programmes

button, and select the Starch
programme.

^

Select a spin speed or the Rinse hold
extra option.

^

Press the Start/Stop button.

Colour run and dye removers/dyes

^

Do not use
removers in this machine.

^

Dyes suitable for use in domestic
washing machines can be used.
However, please note that the salt
used in the dyeing process can
cause corrosion to stainless steel
components in the machine if you
dye frequently. Follow the
manufacturer's instructions carefully.

colour run or dye

Disconnect the machine from the

,

mains electricity supply and
withdraw the plug from the socket
before cleaning the machine.

The washing machine must not

,

be hosed down.

A range of Miele branded cleaning and
conditioning products are available to
order from your Dealer, the Miele Spare
Parts Department or via the internet on
www.miele-shop.com.

External casing and fascia
panel

^ Clean the casing with a mild

non-abrasive cleaning agent or soap
and water using a well wrung-out
cloth. Wipe dry with a soft cloth.

Cleaning and care

Extra cleaning

Carry out a hot wash (70°C or above)
with powder detergent approx. every 6
weeks to help prevent deposits building
up in the machine. These can occur
when washing is mainly done at low
temperatures, and also lead to
unpleasant smells. If you have no
reason to wash occasionally at this high
temperature, then run a Cottons 95°C
programme with detergent but no
laundry at regular intervals.

Cleaning the detergent
dispenser drawer

Remove detergent residues regularly.

^ The drum can be cleaned using a

suitable proprietary stainless-steel
cleaning agent following the
manufacturer's instructions on the
packaging.

,

Do not use solvents, abrasive
cleaners, glass cleaners or
all-purpose cleaning agents.
These might damage plastic
surfaces and other components
because of the chemicals they
contain.

^

Pull out the detergent dispenser
drawer until a resistance is felt. Press
down the release catch and at the
same time pull the drawer right out of
the machine.

^

Clean the detergent drawer with
warm water.

41

Cleaning and care

Cleaning the siphon and conditioner
channel

1. Remove the siphon from

compartment § and rinse under
warm running water. Clean the
siphon tube in the same way.

2. Replace the siphon.

Cleaning the detergent dispenser
drawer housing

^ Use a bottle brush to remove

detergent residues and limescale
from the jets inside the detergent
dispenser drawer housing.

Descaling the machine

If the correct amount of detergent is
dispensed, the machine should not
need to be descaled. If, however, you
do wish to descale the machine only
use proprietary non-corrosive descaling
agents and strictly observe the
instructions on the packaging.

^

Clean the fabric conditioner channel
using a brush and warm water.

If starching frequently, thoroughly
clean the siphon, the siphon tube
and the fabric conditioner channel
regularly. A build-up of starch will
cause them to get clogged.

42

Cleaning and care

Cleaning the dispensing unit

The container should be cleaned each
time you change brand of liquid
detergent.

Cleaning the container and lid

Do not use solvents, abrasive

,

cleaners, glass cleaners or
all-purpose cleaning agents.
These might damage plastic
surfaces and other components
because of the chemicals they
contain.

^ Remove the container from its base.

^ Remove the lid.

^ Rinse the container with hot water to

remove any detergent residues.

^ Clean the container and lid with a

mild non-abrasive cleaning agent or
soap and water. Wipe dry with a soft
cloth.

Cleaning the dispensing tube

It is not normally necessary to clean the
dispensing tube.

After refitting the container, sufficient
detergent for 2-3 washes will still be in
the system. After that the new detergent
will be used.

However if you have had any problems
with the old detergent (e.g. you have
had to change brand because of an
allergic reaction), you will have to
dismantle the dispensing tube and
rinse it out thoroughly.

After cleaning, the dispensing tube
must be primed with detergent again
and the dosage level must be set. See
"Before using for the first time

- Priming the liquid detergent
dispensing system" and "Liquid
detergent dispensing - Dosage level".

^

Clean the valve in the bottom of the
container.

Remember to reset the detergent
dosage level if you change brand of
liquid detergent.

43

Cleaning and care

Cleaning the filter in the water
inlet

The washing machine has a filter to
protect the water inlet valve.

The accessible filter in the union in the
open end of the inlet hose should be
checked every six months, or more
often if there are frequent interruptions
to the external water supply.

First turn off the stopcock.

^

Unscrew the threaded union

^

connecting the free end of the inlet
hose to the stopcock.

^ Remove the rubber seal 1 from the

recess.

^ Using pointed pliers, take hold of the

plastic filter bar 2 and remove.

^ Clean the plastic filter.

^ Put the filter and seal back in the

reverse order and reconnect the
hose.

44

Turn on the stopcock and check the
connection is watertight. If water drips
out, tighten the connection.

Never forget to put the filter back in
place after cleaning.

Problem solving guide

With the help of the following notes, minor faults in the performance of the
machine, some of which may result from incorrect operation, can be put right
without contacting the Service Department.

Repair work to electrical appliances should only be carried out by a

,

suitably qualified person in strict accordance with current local and national
safety regulations. Repairs and other work by unqualified persons could be
dangerous. The manufacturer cannot be held liable for unauthorised work.

The programme does not start

Problem Possible cause Remedy

The display remains
dark and the indicator
lights for the
programme buttons
are not lit up.

You are asked to enter
a code.

The display is dark. The display has

There is no power to
the machine.

Access via a code has
been activated.

switched off
automatically to save
energy (Standby
mode).

Check whether
– the mains plug is plugged

in and switched on.

– the fuse or circuit breaker

has tripped.

Enter the code and confirm
the entry. Deactivate the
code if you do not wish this
message to appear in the
display the next time the
machine is switched on.

Press a button. Standby
comes to an end.

45

Problem solving guide

Fault messages in the display

Problem Possible cause Remedy A

Fault

2

Check drainage
system

Fault

2

Water intake
Open stopcock

Waterproof system

L

activated
Close the stopcock

Technical fault.

;

Call the Service
Department

The following flashes in
the display:

Anti-crease

alternately with

Check detergent

The water outlet is

–

blocked or
restricted.

The drain hose has

–

Clean the drain filter and

–

the drain pump.
The maximum delivery

–

head is 1 m.

been fixed too high.

The water inlet is
blocked or restricted.

Check whether

the stopcock is opened

–

properly.
the inlet hose is kinked.

–

The water protection
system has reacted.

Call the Service
Department.

There is a fault. Start the programme again.

If the fault message
appears again, contact the
Service Department.

Excessive foam has
built up during
washing.

Check:
–

the amount of detergent
used.

–

the dosage level, if using
Automatic dispensing.

Follow the instructions on
the manufacturer's
packaging and also take
the degree of soiling of the
laundry into account.

A To switch off the fault message: Switch the machine off with the I-On/0-Off

button.

46

Problem solving guide

Problems with the automatic liquid detergent dispensing
system

Problem Possible cause Remedy

No liquid detergent
has been dispensed.

Using automatic liquid
detergent dispensing
does not give the
required result.

The liquid detergent
container and tube are
empty.

The tube is kinked or
squashed.

The Automatic
dispensing button has
not been activated.

If none of the above is the case, call the Service
Department.

Not enough liquid
detergent was
dispensed.

The dosage level has
been set too low.

Add liquid detergent to the
container and fill the tube with
liquid detergent as described
in "Before using for the first
time - Priming the liquid
detergent dispensing system".

Make sure you remember to
refill the liquid detergent
container in good time.

Position the tube so that it is
free of kinks.

The indicator light for the
Automatic dispensing button
will come on when the button
is pressed.

Check whether the opening in
the lid of the container has
become clogged.

Increase the dosage level and
select a higher degree of
soiling setting, if necessary.

47

Problem solving guide

Problem Possible cause Remedy

The laundry is not
clean even though the
dosage level is set
correctly.

The liquid detergent
has dried out.

The wrong cleaning
agent e.g. powder
detergent, bleaching
agent or fabric
conditioner, was
added to the liquid
detergent container by
mistake.

There are dark specks
in the liquid detergent.

Liquid detergents
usually contain no
bleaching agents.
They do not remove
fruit, coffee and tea
stains.

The container has not
been closed properly.

Empty out the agent and clean the container and the
valve in the bottom of the container thoroughly.

Check whether any of the wrong cleaning agent has
made its way into the dispensing tube. If it has, the
tube must be dismantled and cleaned thoroughly.

Mould has developed
in the detergent.

Instead of liquid detergent,

–

use a general purpose
powder detergent
containing a bleaching
agent.

or

Add stain removers into

–

compartment j of the
detergent dispenser
drawer.

Clean the container, refill it
with liquid detergent and
close the lid securely.

Pour the liquid detergent out
of the container and then
clean the container
thoroughly.

48

General problems

Problem Possible cause Remedy

The machine shakes
during the spin cycle.

The laundry has not
been spun properly and
is still wet.

The laundry has not
been spun satisfactorily.

The pump makes
strange noises.

There is a lot of
detergent residue in the
detergent drawer.

Fabric conditioner is not
completely dispensed or
too much water remains
in the § compartment.

The display is in a
different language.

When laundry is dry it
feels hard to the touch.

Problem solving guide

The machine feet are not
level.

The machine detected an
imbalance during the final
spin and reduced the
spin speed automatically.

The spin speed selected
was too low.

This is not a fault! These noises occur at the end of
a pump sequence as a normal part of the operation.

The water pressure is too
low.

Powder detergent used
with water softeners can
be sticky.

The siphon tube is not
correctly positioned, or is
clogged up.

A different language has
been selected in Settings
Language J.

Too vigorous wash
action.

Not enough detergent
used.

No fabric conditioner
used.

Level the machine (see
"Installation).

Include both large and
small items in the load as
this will give better
distribution.

Select a higher spin
speed next time.

– Clean the water inlet

filter.

– Select Water plus.

Add washing powder
and then add the water
softener.

Clean the siphon, (see
“Cleaning and care" ­"Cleaning the detergent
dispenser drawer”).

Set the language you
want. The flag symbol
will guide you.

Programme in gentle
action and more water.

Increase detergent dose
to prevent limescale
build up in laundry.

Use fabric conditioner in
last rinse.

49

Problem solving guide

An unsatisfactory wash result

Problem Possible cause Remedy

Grey, greasy
particles cling to
washed laundry.

White residues
which look like
powder detergent
are seen on dark
textiles after
washing.

A stale smell is in
the drum and on
the laundry.

Clothes are coming
out creased.

Insufficient amounts of
detergent were used to
break down the particles
of grease in heavily
soiled laundry.

The detergent contained
compounds (zeolites) to
aid water softening
which are not soluble in
water. They have ended
up on the laundry.

Low temperature
washing.

Programme was
overloaded.

The wrong programme
was used.

Use more detergent.

–

Before washing the next load

–

run a Cottons 95°C
programme with powder
detergent but without a load.

Try and brush off the

–

residues with a soft brush
once the laundry is dry.

Wash dark textiles using a

–

detergent which contains no
zeolites. Liquid detergents
usually contain no zeolites.

– Use the Dark laundry

programme for dark coloured
laundry.

Before washing the next load
run a Cottons 95°C programme
with powder detergent but
without a load.

Reduce the quantity of clothes
in the drum.

–

Check care labels and the
programme chart.

–

Use easy iron conditioners.

50

Problem solving guide

The door will not open

Possible cause Remedy

The machine is not
connected to the
electricity supply and/or is
not switched on.

The safety lock has been
activated.

Access via a code has
been activated.

Power cut. Open the drum door as described in the next

The door was not correctly
engaged.

There is still water in the
drum and the machine is
unable to drain.

For safety reasons the drum door cannot be opened if the suds temperature is
higher than 55°C.

Insert the plug in the socket and switch on and/or
switch the machine on with the I-On/0-Off button.

Deactivate the safety lock as described in
"Changing the programme sequence - Safety
lock".

Deactivate the code as described in "Settings
menu".

section.

Press hard against the lock side of the drum door
and then press the Door button.

Clean the drain filter and drain pump as described
in the next section.

51

Problem solving guide

Opening the drum door in the
event of a blocked drain outlet
and/or power failure

Switch the washing machine off.

^

There is a lever behind the detergent
drawer fascia panel.

^ Remove the lever.

Blocked drain outlet

If the drain outlet is blocked, up to
25 litres of water will be retained in the
machine.

Caution: if laundry has been

,

washed at a high temperature, water
draining out of the machine will still
be hot. Danger of scalding!

Procedure for draining the machine

Place a suitable container under the

^

access flap.

When draining water from the
machine, do not unscrew the drain
filter completely or take it right out.

^

Use it to open the access flap.

52

^

Unscrew the drain filter lid until water
runs out.

To interrupt the flow of water:

^

Tighten the drain filter back up again.

Once the flow of water ceases:

Remove the drain filter completely.

^

^ Clean it thoroughly.

Problem solving guide

Make sure the drain filter is

,

securely tightened. Otherwise there
is a risk of water leakage during use.

Opening the drum door

Always make sure that the drum

,

is stationary before reaching into the
machine to remove laundry.
Reaching into a moving drum is
extremely dangerous.

^

Remove any foreign objects (e.g.
buttons, coins, etc.) and fluff from the
filter housing. Turn the impeller by
hand to check that it rotates freely.
Any foreign object causing an
obstruction should be removed.

^

Put the drain filter back in place and
secure.

^

Pull the emergency release
downwards (see illustration). The
drum door will open.

53

After sales service

In the event of any faults which you
cannot remedy yourself, please
contact:

your Miele Dealer or

–

the Miele Customer Contact Centre

–

(see back cover for contact details).

When contacting your Dealer or Miele,
please quote the model and serial
number of your machine, both of which
are shown on the data plate visible
above the porthole glass when the door
is open.

Future updates (PC)

The indicator light marked PC is the
interface used by Miele service
technicians during servicing work for
testing purposes and for updating the
machine's programme data.

Appliance guarantee

Please see the guarantee card
supplied with your machine.

Optional accessories

Optional accessories for this washing
machine are available from your Miele
Dealer, the Miele Spare Parts
Department or via the internet at
www.miele-shop.com.

Please note that telephone calls may
be monitored and recorded for
training purposes.

54

Front view

Installation and connection

a Inlet hose with "Waterproof" system

b Electricity supply cable

c - f Flexible drain hose (with

detachable swivel elbow)

g Control panel

h Detergent dispenser drawer

i Drum door

j Access to drain filter, drain pump

and emergency release

k Four height adjustable feet

55

Installation and connection

Rear view

a Protruding lid for holding when

moving the machine

b Electricity supply cable

c Inlet hose with "Waterproof" system

d Drain hose

56

e Transit bar covers

f Restraining clip for inlet hose and

drain hose

g Restraining clips for transit bars

when removed

h Dispensing tube for automatic liquid

detergent dispensing system

Installation and connection

Installation surface

A concrete floor is the most suitable
installation surface for a washing
machine, being far less prone to
vibration during the spin cycle than
wooden floorboards or a carpeted
surface.

Please note the following points:

The machine must be level and

^

securely positioned.

To avoid vibrations during spinning,

^

the machine should not be installed
on soft floor coverings.

If installing on a wooden joist floor:

^ We recommend a plywood base (at

least 59x52x3 cm). The base should
span several joists and be bolted to
the joists and not only to the
floorboards. Check for the presence
of pipes and cables first.

If possible, install the machine in a
corner, as this is usually the most stable
part of the floor.

Transporting the machine to its
installation site

To manoeuvre the machine out of its
packing case to its installation site, hold
it by the front feet as well as by the
edge of the lid where it protrudes to the
rear of the washing machine.

Ensure that the machine feet and

,

the floor are dry to prevent the
machine from slipping during the
spin cycle.

Removing the transit fittings

,

If the machine is installed on a
raised plinth, it has to be secured
against slippage during spinning
using retaining clips (available from
the Miele Spare Parts Dept).

^

To remove the left and right covers

1. Use a screwdriver to prise out the

cover as illustrated.

2. Pull the cover forwards to remove.

57

Installation and connection

Using the spanner supplied, turn the

^

left-hand transit bar 90°, then

^

withdraw the transit bar.

Turn the right-hand transit bar 90°,

^

then

^

withdraw the transit bar.

58

To avoid the risk of injury the

,

holes for the transit bars must be
covered after the transit bars have
been removed.

^ Fit the covers onto the two holes.

Then plug the holes as shown with
the caps.

Installation and connection

Secure the transit bars to the back of

^

the washing machine. Make sure that
holes b are fitted over retainers a.

The machine must not be moved

,

without the transit bars in place.
Store them as shown or keep them
in a safe place for future use. They
must be re-fitted if the machine is to
be moved again (e.g. when moving
house).

Re-fitting the transit bars

Re-fitting is carried out by reversing the
procedure.

59

Installation and connection

Levelling the machine

The machine must stand perfectly level
on all four feet to ensure safe and
proper operation.

Incorrect installation may increase
electricity and water consumption and
may cause the machine to move about.

Screwing out and adjusting the feet

The four adjustable screw feet are used
to level the machine. All four feet are
screwed in when the machine is
delivered.

Use a spirit level to check the

^

machine is standing level.

^ Hold foot 1 securely with a pipe

wrench. Turn counter nut 2 again
using the spanner supplied until it
sits firmly up against the housing.

,

All four counter nuts must sit
firmly up against the housing. Please
also check this for the feet which did
not need adjustment. Otherwise
there is the danger of the machine
moving about.

^

Using the spanner supplied, turn
counter nut 2 in a clockwise
direction. Then turn counter nut 2
together with foot 1 to unscrew.

60

This washing machine is not suitable
for building under a worktop.

Installation and connection

Washer-dryer stack

A T 200, T 4000, T 7000 or T 8000 Miele
tumble dryer can be stacked on this
machine using a WTV stacking kit
which can be purchased from your
Dealer or the Miele Spare Parts
Department.

Washer-dryer stack using a T 7000
series dryer and WTV 417 stacking
kit

Washer-dryer stack using a T 200,
T 4000 or T 8000 series dryer and
WTV 412 stacking kit

a Safety distance to wall:

at least 2 cm

b Height:

approx. 170 cm

a Safety distance to wall:

at least 2 cm

b Height:

approx. 179 cm

c Depth of the washer-dryer stack:

approx. 67.5 cm

c Depth of the washer-dryer stack:

approx. 69.5 cm

61

Installation and connection

Dispensing unit

The dispensing unit (liquid detergent
container, lid and base) are stored
in the drum when the washing
machine is delivered.

Open the door (the washing machine

^

must be connected to the electricity
supply).

Remove the dispensing unit.

^

Positioning the container

For safety reasons the

,

dispensing unit must not be
positioned above sockets, switches,
lights etc and must be at a distance
of at least 60 cm

It must be easily accessible for
refilling.

The unit can be located in a variety of
positions.

away from them.

a Container (capacity: 5 litres)

b Lid

c Dispensing tube (length: 2 metres).

This is located at the back of the
washing machine.

d Base

Fixings supplied:

–

Hose clip
outlet underneath the container.

–

2 screws
position.

62

for securing the tube to the

for securing the base in

a On the lid of the washing machine

b Beside the washing machine, e.g. on

a shelf

c In a unit next to the washing machine

d Fixed to the wall.

Fitting the tube

The tube must not be kinked,

,

squashed or damaged in any way.
Do not remove the stopper at the
end of the tube until after it has been
fitted. If dirt were to get into the tube,
it could damage the pump.

Place the dispensing unit in the

^

position you have chosen for it.

Take the end of the tube from the

^

back of the washing machine and
position it so that it reaches the base
of the dispensing unit.

^ Take the container off its base and

unscrew the base.

^ Remove the stopper from the end of

the tube.

Installation and connection

Attach the tube to the outlet

^

underneath the base using the hose
clip supplied.

If the tube is too long, it can be
looped behind the washing machine.

Extension tube

A 5 metre long extension tube is
available from your Miele dealer or the
Miele Spare Parts Department as an
optional extra.

If the 5 metre tube is used, an
increased dosage level of 215 ml
needs to be set when the liquid
detergent dispensing system is primed

- see "Before using for the first time".

63

Installation and connection

Fitting the base

Only use the screws supplied

,

to secure the dispensing unit to the
lid of the washing machine.
Using different screws could
damage the washing machine.

The tube must be attached to the
outlet underneath the base before the
base is screwed into position.

Secure the base to the lid of the

^

washing machine by hand, using the
screws supplied.

^ Place the rubber stoppers in the

holes (this time from above).

^ Now place the container onto the

base and push it down firmly.

^

Use a thin screwdriver to remove the
two rubber stoppers.

64

Installation and connection

The Miele Waterproof system

The Miele Waterproof system protects
the washing machine from water
damage.

The system consists of three main
components:

1) the inlet hose

2) the electronic unit and the washing
machine housing

3) the drain hose

1) Inlet hose

– The inlet hose is fitted with an

additional electrical safety valve
which works like an automatic
stopcock and is housed in the inlet
hose connection box.

– It is pressure tested to between

7,000 and 10,000 kPa.

– The inlet hose has a protective

sleeve.

2) Electronic unit and washing
machine housing

Sump

–

Any leaking water is collected in a
sump in the base of the machine. A
float switches off the safety valves,
preventing any more water from
flowing into the machine and water in
the suds container is pumped away.

Overflow protection

–

This prevents the washing machine
taking in too much water. If the water
level exceeds a certain level, the
drain pump switches in and pumps
the excess water away.

3) Drain hose

The drain hose is protected by a
ventilation system which prevents the
washing machine from being
emptied completely.

Any leaking water from the inlet hose
is fed into the sump through this
protective sleeve. A float switches off
the safety valve, preventing any
more water from flowing into the
machine and water in the suds
container is pumped away.

65

Installation and connection

Connection to the water supply

The plastic casing of the safety

,

valve contains electrical
components. The Waterproof system
must only be connected to its own
stopcock. It must not be connected
to mixer taps or similar and must not
be fitted in areas where there is the
risk of water or other liquids
reaching it.

Do not get wet.

The machine should be connected to
the mains water supply in accordance
with local and national safety
regulations. The German authorities do
not require it to have a non-return valve
as the washing machine has been
designed to comply with DIN
regulations.

The machine is designed to operate
with a flow pressure of between 100
and 1,000 kPa (1-10 bar). If it is higher
than 1,000 kPa it is essential to fit a
pressure reducing valve.

Connection to the mains water supply
should incorporate a mains stopcock

3

with

/4" thread. The stopcock should

be fitted by a qualified plumber.

,The connection point is subject

to mains water pressure. Turn on the
stopcock slowly and check for leaks.
Correct the position of the washer
and union if appropriate.

The protective sleeve of the hose
must not be damaged or kinked.

66

The washing machine is not suitable
for connection to a hot water supply
and connection to a household
water softener is not recommended.

Maintenance and care

If you intend to unscrew the Miele
Waterproof system hose from the
stopcock it is essential to disconnect
the machine from the electricity supply
first.

Only use a Miele Waterproof system
hose should you need a replacement.

In order to protect the water inlet
valve, the dirt filter in the water inlet
valve connection must not be
removed.

Extension hose

A 1.5 metre long (metal) extension hose
is available from your Miele dealer or
the Miele Spare Parts Department as an
optional extra.

This hose is tested to withstand
pressures of up to 14,000 kPa and can
be used as a flexible extension to the
water supply.

Installation and connection

N.B. Using this hose renders the
Waterproof system safety valve on the
inlet hose ineffective.

67

Installation and connection

Connection to the drainage
system

The machine drains via a drain pump
with a delivery head of 1 metre*. The
drain hose must not be kinked as this
restricts drainage. The swivel elbow at
the end of the hose can be turned in
either direction, or can be detached if
required, with a sharp twist and pull.

If required, the drain hose can be
extended to a length of 5 m. The
necessary parts can purchased from
the Miele Spare Parts Department or
your Miele dealer.

* For a delivery head of more than 1 m
(up to a max. of 1.8 m) a replacement
drain pump will need to be fitted.
Please contact the Miele Spare Parts
Department or your Miele Dealer.

Drain hose connection:

1. Direct into a sink or basin:

Please note the following:

–

Hook the hose over the edge and
secure.

Please note:

a Adapter

b Nut

c Hose clip

d End of the hose

^ Fit adapter a to the sink drain outlet

using nut b.

^ Attach the end of the hose d to

adapter a.

^

Use a screwdriver to tighten hose
clip c up close to the nut.

–

Make sure that the water can drain
away freely without hindrance.
Otherwise there is a risk of water
overflowing or of some of the drained
water being sucked back into the
machine.

2. Connected securely to a plastic

drain pipe with a rubber nipple.
There is no need to use a non-return
valve.

3. Connected securely to a standpipe.

4. Connected securely to a floor gully.

68

Installation and connection

Electrical connection U.K.

All electrical work should be carried out
by a suitably qualified and competent
person, in strict accordance with
current national and local safety
regulations (BS 7671 in the UK).

Ensure power is not supplied to the
appliance until after installation work
has been carried out.

The appliance is supplied with a mains
cable with moulded plug ready for
connection to a 230-240V mains
supply.

Please ensure the connection data
quoted on the data plate match the
household mains supply.

Connection should be made via a
suitable switched socket which is easily
accessible after installation.

For extra safety it is advisable to install
a suitable residual current device
(RCD). Contact a qualified electrician
for advice.

Non-rewireable plugs BS 1363

The fuse cover must be refitted when
changing the fuse, and if the fuse cover
is lost, the plug must not be used until a
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
embossed in words on the base of the
plug (as applicable to the design of
plug fitted).

Replacement fuses should be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
your local electrical supplier.

WARNING: THIS APPLIANCE
MUST BE EARTHED

Do not connect via an extension lead.
Extension leads do not guarantee the
required safety of the appliance (e.g.
danger of overheating).

69

Consumption data

Load Consumption data

Energy Water Duration

in kWh in litres Short Normal

Cottons 95°C 6.0 kg 1.99 47 2 h 09 min

Minimum iron 40°C

Delicates 30°C 2.0 kg 0.35 69 49 min 59 min
Woollens / 30°C 2.0 kg 0.23 39 – 39 min

Automatic 40°C 3.5 kg 0.35 – 0.50 40-55 – 1 h 18 min

Shirts 60°C 2.0 kg 1.00 59 1 h 02 min 1 h 12 min

Express 40°C 3.0 kg 0.30 34 – 30 min

Denim 40°C 3.0 kg 0.50 52 50 min 1 h 00 min

Hygiene 60°C 6.0 kg 1.40 55 – 2 h 20 min

Dark garments 40°C 3.0 kg 0.60 60 1 h 02 min 1 h 15 min

Curtains 40°C 2.0 kg 0.45 38 – 55 min

Pillows 60°C 1 pillow 0.80 44 – 1 h 20 min
Silks / 30°C 1.0 kg 0.25 39 – 36 min

Sportswear 40°C 2.0 kg 0.35 35 47 min 1 h 07min

Outerwear 40°C 2.0 kg 0.45 59 53 min 1 h 03 min

First wash 40°C 3.0 kg 0.37 35 – 51 min

Proofing 40°C 2.0 kg 0.30 12 – 29 min

1)

60°C

60°C 3.0 kg 0.73 39 1 h 03 min

40°C

40°C

6.0 kg 1.02 47 1 h 49 min

1)

6.0 kg 0.65 59 2 h 04 min

2)

3.0 kg 0.36 39 59 min

1)

3.0 kg 0.50 55 59 min 1 h 19 min

Notes for test institutes:

1)

EN 60456 test programme

2)

Short programme for test institutes; the Short extra option must be selected.

Consumption data can vary from the nominal values given depending on water
pressure, water hardness, water inlet temperature, room temperature, type and
volume of load, fluctuations in the electricity supply and any extra options
selected.

70

Technical data

Height 850 mm

Width 595 mm

Depth 634 mm

Depth with door open 1074 mm

Weight 99 kg

Maximum floor load 1,600 Newton (approx. 160 kg)

Capacity 6 kg dry laundry

Voltage see data plate

Connected load see data plate

Fuse rating see data plate / plug

Consumption data see "Consumption data"

Water flow pressure minimum 100 kPa (1 bar)

Water flow pressure maximum 1,000 kPa (10 bar)

Inlet hose length 1.60 m

Drain hose length 1.50 m

Mains connection cable length 1.60 m

Delivery head max. 1.00 m

Maximum drainage length 5.00 m

LEDs Class 1

Test certificates awarded see data plate

71

Settings menu
for changing default settings

The Settings menu can be used to alter the machine's electronics to suit
changing requirements.
Settings can be altered at any time.

Settings menu

To open the Settings menu

Connect the machine to the

^

electricity supply.

Switch on the washing machine.

^

Press both menu buttons at the same

^

time until the following appears in the
display:

Settings

Language !

Continue

OK

You are now in the Settings menu.

^ Select the setting you want with the

left hand Menu button under
Continue, and confirm your selection
with the right hand Menu button
under OK.

Language F

The display can be set to appear in
one of several different languages.

Time (of day)

First select either a 24 hour or 12 hour
clock. You can then set the current time
of day.

Clock format

Select the clock format you want with

^

the left hand Menu button under
Continue, and confirm your selection
with the right hand Menu button
under OK.

Set the time of day

^ Select the Set the time of day

sub-menu and use the Menu buttons
to set the time.

You can select the language you want
via the Language sub-menu.

The flag after the word Language acts
as a guide to prevent a language which
will not be understood from being set.

A tick L will appear beside the
language to show that it has been set.

73

Settings menu

Detergent dosage

If you change the brand of liquid
detergent for the automatic dispensing
system you will also need to alter the
dosage level set for it.

See "Liquid detergent dispensing ­Dosage level" for more information.

Gentle action

Activating gentle action reduces the
drum action and is suitable for
washing slightly soiled items more
gently. It should be activated for
garments with a single bar under the
care label and for articles which feel
too hard after they have been dried.

Gentle action can be activated for the
Cottons and the Minimum iron
programmes.

The machine is delivered with the
Gentle action setting deactivated.

A tick L will appear beside the option
to show that it has been set.

Longer pre-wash

The pre-wash for the Cottons
programme can be extended by 6, 9
or 12 minutes.

The default setting for the pre-wash is
25 minutes.

If you require a longer pre-wash, this
can be extended.

A tick L will appear beside the option
to show that it has been set.

Suds cooling

When this is activated, additional
water flows into the drum at the end
of the main wash to cool the suds
down. Hot suds can damage plastic
drainage pipes.

Suds cooling takes place when
temperatures of 95°C and 75°C are
selected.

Suds cooling should be activated:

–

to prevent the danger of scalding if
the drain hose is hooked over the
edge of a sink or basin.

74

–

where the drainage pipes do not
comply with DIN 1986.

The machine is delivered with Suds
cooling deactivated.

A tick L will appear beside the option
to show that it has been set.

Lock code

The code prevents your machine
being used without your knowledge.

Settings menu

Lock code

125

When the code has been activated, you
have to enter a code after switching the
washing machine on. Otherwise the
washing machine cannot be operated.

To activate the Lock code

Lock code

Activate

Continue

OK

^ Press the right hand Menu button

under OK.

^ The display will now request that a

code is entered. The code is 125 and
cannot be altered.

To enter the Lock code

Lock code

0 00

*

^

Enter the first number with the left

OK

hand Menu button under *. Confirm

your selection of this number by
pressing the right hand Menu button
under OK. Now enter the second
number.

Back A OK

Confirm the code by pressing the

^

right hand Menu button under OK or,
if you have made a mistake, press
the left hand Menu button under

Back

A.

The following will appear in the display:

X Lock code activated.

Entry OK

Once the machine is switched off, it
can only be used again if the code is
entered.

To use the washing machine when
the code is activated

When the machine is switched on
again, the display will request the code.

^

Enter code 125 as described above
and confirm the entry.

The washing machine is now unlocked
and ready for use.

To deactivate the Lock code

Proceed as for activating the code.

^

Repeat the process until all three
numbers have been entered.

75

Settings menu

Temperature unit

You can chose for the temperature to
be displayed in °C/Celsius or
°F/Fahrenheit.

A tick L will appear beside the option
to show that it has been set.

Buzzer

When the buzzer function has been
activated, an audible tone sounds at
the end of a programme or when
Rinse hold is reached.

There are two volumes:

Normal

(the machine is delivered with this
option as the default setting)

The buzzer sounds at the end of a
programme or when Rinse hold is
reached.

Loud

The buzzer sounds at maximum volume
Loud at the end of a programme or
when Rinse hold is reached.

A tick L will appear beside the option
to show that it has been set.

Keypad tone

An audible tone sounds each time a
button is pressed.

The machine is delivered with the
keypad tone switched off.

A tick L will appear beside the option
to show that it has been set.

Brightness

There are ten different display
brightness settings.

The machine is delivered with the
display brightness on setting 5.

This will change as soon as a different
setting is chosen.

Contrast

There are ten different display
contrast settings.

The machine is delivered with the
display contrast on setting 5.

This will change as soon as a different
setting is chosen.

76

Settings menu

Standby display

To save energy, the display goes out
and the indicator light for the
Start/Stop button will start flashing
slowly.

The display will always go out,

if a programme is not selected within

–

10 minutes of the machine being
switched on.
10 minutes after the end of a

–

programme.

Pressing one of the buttons switches
the display back on again.

You can also choose whether you want
the display to go out 10 minutes after a
programme has started or to remain
visible throughout the programme.

On

The standby function is switched on.
When this option is selected, the
display will go out 10 minutes after a
programme has started.

Not in current programme

(the machine is delivered with this
option selected)

The standby function is switched off.
The display will remain visible during a
programme.

will store the changes in memory at
the start of a programme.

When this programme is chosen again
these settings will appear in the
display.

The machine is delivered with the
memory function deactivated.

Anti-crease

Anti-crease helps prevent creasing if
laundry is not normally removed im
mediately after the end of a
programme.

The drum will turn at intervals for up to
30 minutes after the programme has
finished. The door can be opened and
laundry removed at any time during the
anti-crease phase.

On

(the machine is delivered with this
option selected)

Anti-crease is activated.

Off

Anti-crease is deactivated.

To close the Settings menu

Settings

-

Memory

If an extra option has been selected
for a programme, or the
recommended temperature or spin
speed has been altered, the machine

Back A

Continue

^

Press the right hand Menu button

OK

under OK.

77

Optional accessories

Miele washing machines offer perfect
care for your laundry and feature a
wide range of special programmes
designed to suit the fabric being
washed. And now Miele have
developed a range of specialist
CareCollection detergents and
conditioning products to offer you a
complete package for cleaning and
caring for your laundry.

The Miele CareCollection detergents
and conditioning products are listed
below. You can order these and many
other useful products via the internet at:

All the products can also be ordered
via the Miele Customer Contact Centre
(see back cover for contact details).

CareCollection

Miele specialist detergents

"Outdoor wear"

This specialist detergent will clean your
water-repellent outerwear with care.

"Sportswear"

The Miele Sportswear detergent is
designed to clean sportswear whilst
taking care of the special microfibres
used in these garments. It will help to
neutralise and remove odours whilst
protecting the colour of the fabric and
preventing static build-up.

"Down Items"

This special-purpose detergent
contains a mild tenside and has been
specially formulated to keep down-filled
items supple and to give them bounce.

78

Miele proofing agent

This special finishing agent reproofs
garments against wind and water and
provides a dirt-repellent finish whilst
retaining elasticity and breathability.

Optional accessories

"UltraWhite" detergent

This multi-purpose powder detergent
has excellent stain removal properties
and is suitable for white and light
coloured laundry as well as heavily
soiled coloured items.

"UltraColor" detergent for coloured
garments

This liquid detergent is particularly
suitable for cleaning coloured and dark
garments. The special formulation
offers effective stain removal, even at
low temperatures, while helping to
prevent colours fading.

Liquid detergent "For Delicates"

This liquid detergent is ideal for the
gentle treatment of delicate fabrics,
such as wool and silk. Its special
formulation cleans effectively at
temperatures as low as 20°C, while
protecting the colour of your delicate
garments.

Fabric conditioner

The Miele fabric conditioner will give
your laundry a fresh, natural fragrance.
It makes garments soft to handle and
prevents static build-up during tumble
drying.

79

Alteration rights reserved/0309/W 4449 WPS LiquidWash

M.-Nr. 07 170 970 / 02