Fully Integrated
24” MasterCool
II
K 2601 Vi / K 2611 Vi
F 2601 Vi* / F 2611 Vi*
KWT 2601 Vi / KWT 2611 Vi
KWT 2661 ViS / KWT 2671 ViS
Shown: KWT 2611 Vi
Please note: This information is subject to
*The following models are not available in Canada : F 2601 Vi & F 2611 Vi
change
Specification Sheets TRS 04252019
8miele.ca
Fully Integrated
24” MasterCool II
SPECIFICATIONS
Overall Unit Dimensions 233/4” (604 mm) W x 833/4”- 853/16” (2127 - 2164 mm) H x 24” (610 mm) D [Depth does not include door panel]
Niche
Minimum Cabinet Niche Opening 24” (610 mm) W* x 84” - 853/16” (2134 - 2164 mm) H x 243/4” (629 mm) D
Interior Volume K 26x1 Vi KWT 26x1 Vi F 26x1 Vi
Refrigeration Volume ** ** 0
Freezer Volume 0 0 **
Chiller Volume 0 ** 0
Electrical
Electrical Requirements
Power Cord NEMA 5-15 plug, 5 ft (1.52 m)
Plumbing K 26x1 Vi KWT 26x1 Vi F 26x1 Vi
Water Supply Requirements -
Water Connection Line
Shipping
Shipping Weight 346 lbs (157 kg) 357 lbs (162 kg) 375 lbs (170 kg)
Shipping Dimensions 267/8” (682 mm) W x 841/4” (1,240 mm) H x 297/8” (759 mm) D
Support
Call Miele
Miele Website
20/20 Link
Please note the following:
• This specication sheet is for a single built-in unit.
• When combining multiple MasterCool units side-by-side, please refer to the Merging Kit specication sheet.
*If design calls for a partition less than 6 5/16” (160 mm) the left unit’s cutout will require an additional 1/8” (3 mm) to the width to allow installation of
the Heating Mat/Merge Kit.
K 26x1 Vi KWT 26x1 Vi F 26x1 Vi
In the case of side-by-side installations, a separate outlet must be used for each appliance.
-
K 26x1 Vi KWT 26x1 Vi F 26x1 Vi
110V / 120V, 60Hz, 15 Amps
Connect to a cold water supply only. Do not connect to a
low-mineral or a reverse osmosis system. Must be connected
to a shut-off valve. The water shut-off valve must be accessible
after installation. The water pressure must be between 29 psi
(2 bar) and 116 psi (8 bar). If the pressure is higher than 120 psi
(8.3 bar), a pressure reducing valve must be installed.
Standard 1/4” O.D flexible water line. The maximum outer
diameter of the water pipe (without fittings): 3/8” (10 mm).
Water line is not included.
(800) 565-6435
8www.miele.ca
82020technologies.com
K 2601 Vi (Right Hinged)
K 2611 Vi (Left Hinged)
F 2661 Vi (Right Hinged)
F 2671 Vi (Left Hinged)
KWT 2601 Vi (Right Hinged)
KWT 2611 Vi (Left Hinged)
KWT 2661 ViS (Right Hinged)
KWT 2671 ViS (Left Hinged)
Page 2 of 12
CUTOUT DIMENSIONS
• Niche depth assumes a 3/4” (19 mm) panel, please
adjust according to custom panel thickness
Fully Integrated
24” MasterCool II
CUTOUT DETAILS
• The electrical connection must not be positioned higher
than 9” (228.6 mm) above the oor.
• The 1/4” (6.4 mm) plumbed water connection should
not be positioned higher than 2” (50.8 mm) above the
oor.
Notes:
In case of an emergency the electrical outlet must be
easily accessible and must not be concealed behind the
appliance.
Page 3 of 12
Fully Integrated
24” MasterCool II
POWER SUPPLY AND WATER CONNECTION
(Water Connection For F 26x1 Vi Only)
Rear View Front View
Electrical - 5 foot (1.52 m) - 120 Volt - 15 Amp
- NEMA 5-15 molded plug
Water line - 1/4” exible water line - not included
Side View
Water connection is located in front of unit.
1/4” compression tting is needed.
Electrical
Connection
Page 4 of 12
CUSTOM PANEL INSTALLATIONS
Fully Integrated
24” MasterCool II | K 26x1 Vi
Minimum 23 3/4” (604 mm)
Minimum 3/4” (19 mm) outside frame
106 Pounds
Page 5 of 12
DOOR PANEL DIMENSIONS
KFP 2404 - Door Panel
Available as an accessory
for the following models:
• K 26x1 Vi
Fully Integrated
24” MasterCool II | K 26x1 Vi
Page 6 of 12
CUSTOM PANEL INSTALLATIONS
CUSTOM PANEL INSTALLATIONS
Fully Integrated
24” MasterCool II | F 26x1 Vi
23 3/4” (604 mm) in all cases
Minimum 3/4” (19 mm) outside frame
143 Pounds
Page 7 of 12
DOOR PANEL DIMENSIONS &
DISPENSER CUTOUT
KFP 2444 - Door Panel
Available as an accessory
for the following models:
• F 26x1 Vi
Fully Integrated
24” MasterCool II | F 26x1 Vi
Page 8 of 12
CUSTOM PANEL INSTALLATIONSCUSTOM PANEL INSTALLATIONS
5 7/8” (140 mm) min.
17 1/4” - 18 5/8”
(439 - 473 mm)
Fully Integrated
24” MasterCool II | KWT 26x1 Vi(S)
23 3/4” (604 mm)in all cases
Minimum 3/4” (19 mm) outside frame
63 7/8” (1623 mm) max.
137 Pounds
2 1/2” - 3 1/4”
(63.5 - 82.5 mm)
Both Sides
10 1/8” (257 mm) min.
Page 9 of 12
DOOR PANEL DIMENSIONS
KFP 2454 -Door Panel
Available as an accessory
for the following models:
• KWT 26x1 Vi(S)
Fully Integrated
24” MasterCool II | KWT 26x1 Vi(S)
Page 10 of 12
HINGING DETAILS 115° OPENING
Available for the following models:
• K 26x1 Vi
• F 26x1 Vi
• KWT 26x1 Vi(S)
1-1/4” (32 mm)
1-1/2” (38 mm)
1-3/4” (44 mm)
0-3/4” (19 mm)
1” (25 mm)
Fully Integrated
24” MasterCool II
0-3/4” (19 mm)
2-5/8”
(67mm)
2-5/8”
(67mm)
2-1/3” (59mm)
2-1/3” (59mm)
2-1/24”(52mm)
2-1/24”(52mm)
1-3/8”(35mm)
1-3/8”(35mm)
1-1/6”
1-1/6”
17/24” (18mm)
17/24” (18mm)
(29.6mm)
(29.6mm)
1/4”(6.4mm)
1/4”(6.4mm)
1-3/4”(44.5mm)
1-3/4”(44.5mm)
3”(76.2mm)
3”(76.2mm)
0-1/8” (3 mm)
DOOR SWING AT 115° OPENING
1-1/4” (32 mm)
1-1/2” (38 mm)
11 3/4”
(298 mm)
Max
1” (25 mm)
Page 11 of 12
HINGING DETAILS 90° OPENING
Available for the following models:
• K 26x1 Vi
• KWT 26x1 Vi(Si
1-1/4” (32 mm)
1-3/4” (44 mm)
1-1/2” (38 mm)
2” (51 mm)
0-3/4” (19 mm)
1” (25 mm)
Fully Integrated
24” MasterCool II
7/16”
(11 mm)
1-3/16”
(30mm)
1-7/16”
(36.5mm)
1-11/16”
(43mm)
1-15/16”
(49.2mm)
0-1/8” (3 mm)
Handle or object that is
NOT ush with Cabinet
Front.
DOOR SWING AT 90° OPENING
0-3/4” (19 mm)
1” (25 mm)
1-1/4” (32 mm)
1-1/2” (38 mm)
7/16” (11 mm)
/16” (676 mm)
11
26
When installing hinge side next to an appliance or object that is within range of the door panel, limit the door
opening angle to 90°. This is done by installing the banking pin as illustrated.
Insert the banking pin through the holes and drive in with a hammer.
Page 12 of 12
Loading...