
Fully Integrated
30” MasterCool II
All Refrigerator:
K 2801 Vi / K 2811 Vi
All Freezer:
F 2801 Vi / F 2811 Vi
Bottom Mount:
KF 2801 Vi / KF 2811 Vi
Shown: F 2471 Vi merged with K 2801 Vi
Please note: This information is subject to change
Specification Sheets TRS 04252019
8miele.ca

Fully Integrated
30” MasterCool II
SPECIFICATIONS
Overall Unit Dimensions 293/4” (756 mm) W x 833/4”- 853/16” (2127 - 2164 mm) H x 24” (610 mm) D [Depth does not include door panel]
Niche
Minimum Cabinet Niche Opening 30” (762 mm) W* x 84” - 853/16” (2134 - 2164 mm) H x 243/4” (629 mm) D
Interior Volume K 28x1 Vi F 28x1 Vi KF 28x1 Vi
Refrigeration Volume ** 0 **
Freezer Volume 0 ** *
Electrical
Electrical Requirements
Power Cord NEMA 5-15 plug, 5 ft (1.52 m)
Plumbing K 28x1 Vi F 28x1 Vi KF 28x1 Vi
Water Supply Requirements -
Water Connection Line
Shipping
Shipping Weight 395 lbs (179 kg) 399 lbs (181 kg) 450 lbs (204 kg)
Shipping Dimensions 335/8” (950 mm) W x 8913/16” (1,294 mm) H x 291/4” (800 mm) D
Support
Call Miele
Miele Website
20/20 Link
Please note the following:
• This specication sheet is for a single built-in unit.
• When combining multiple MasterCool units side-by-side, please refer to the Merging Kit specication sheet.
*If design calls for a partition less than 6 5/16” (160 mm) the left unit’s cutout will require an additional 1/8” (3 mm) to the width to allow installation of
the Heating Mat/Merge Kit.
K 28x1 Vi F 28x1 Vi KF 28x1 Vi
In the case of side-by-side installations, a separate outlet must be used for each appliance.
-
K 28x1 Vi F 28x1 Vi KF 28x1 Vi
110V / 120V, 60Hz, 15 Amps
Connect to a cold water supply only. Do not connect to a low-mineral or
a reverse osmosis system. Must be connected to a shut-off valve. The
water shut-off valve must be accessible after installation. The water pressure must be between 29 psi (2 bar) and 116 psi (8 bar). If the pressure is
higher than 120 psi (8.3 bar), a pressure reducing valve must be installed.
Standard 1/4” O.D flexible water line. The maximum outer diameter of the
water pipe (without fittings): 3/8” (10 mm). Water line is not included.
(800) 565-6435
8www.miele.ca
82020technologies.com
K 2801 Vi (Right Hinged)
K 2811 Vi (Left Hinged)
F 2801 Vi (Right Hinged)
F 2811 Vi (Left Hinged)
KF 2801 Vi (Right Hinged)
KF 2811 Vi (Left Hinged)
Page 2 of 10

CUTOUT DIMENSIONS
• Niche depth assumes a 3/4” (19 mm) panel, please
adjust according to custom panel thickness
Fully Integrated
30” MasterCool II
CUTOUT DETAILS
• The electrical connection must not be positioned higher
than 9” (228.6 mm) above the oor.
• The 1/4” (6.4 mm) plumbed water connection should
not be positioned higher than 2” (50.8 mm) above the
oor.
Notes:
In case of an emergency the electrical outlet must be
easily accessible and must not be concealed behind the
appliance.
Page 3 of 10

Fully Integrated
30” MasterCool II
POWER SUPPLY AND WATER CONNECTION
(Water Connection For F 28x1 Vi & KF 28x1 Vi Only)
Rear View Front View
Electrical - 5 foot (1.52 m) - 120 Volt - 15 Amp
- NEMA 5-15 molded plug
Water line - 1/4” exible water line - not included
Side View
Water connection is located in front of unit.
1/4” compression tting is needed.
Electrical
Connection
Page 4 of 10

CUSTOM PANEL INSTALLATIONS
Fully Integrated
30” MasterCool II | K 28x1 Vi & F 28x1 Vi
Minimum 29 3/4” (756 mm)
Minimum 3/4” (19 mm) outside frame
106 Pounds
Page 5 of 10

DOOR PANEL DIMENSIONS
KFP 3004 - Door Panel
Available as an accessory
for the following models:
• K 28x1 Vi
• F 28x1 Vi
Fully Integrated
30” MasterCool II | K 28x1 Vi & F 28x1 Vi
Page 6 of 10

CUSTOM PANEL INSTALLATIONS
Fully Integrated
30” MasterCool II | KF 28x1 Vi
Minimum 29 3/4” (756 mm)
Minimum 3/4” (19 mm) outside frame
51 3/8” (1304 mm)
104 lbs
HOM - 51 1/2” (1307 mm) - TKH
Total height of machine. Can be adjusted
to match adjoining cabinets - typically 84”
(2133 mm).
HOM is adjustable between 84” -85 3/16”
(2134 mm - 2164 mm)
TKH =
Toe-kick height 2” - 8 3/8” (51 - 212 mm)
Lower Maximum panel weight: 22 lbs
87” (2210 mm)
84” (2134 mm)
3” (76 mm)
54 1/2” (1379 mm)
Page 7 of 10

DOOR PANEL DIMENSIONS
KFP 3014 - Top Panel
KFP 3024 - Bottom Panel
Available as an accessory
for the following model:
• KF 28x1 Vi
Fully Integrated
30” MasterCool II | KF 28x1 Vi
Page 8 of 10

HINGING DETAILS 115° OPENING
Available for the following models:
• K 28x1 Vi
• F 28x1 Vi
• KF 28x1 Vi
1-1/4” (32 mm)
1-1/2” (38 mm)
1-3/4” (44 mm)
0-3/4” (19 mm)
1” (25 mm)
Fully Integrated
30” MasterCool II
0-3/4” (19 mm)
2-5/8”
(67mm)
2-5/8”
(67mm)
2-1/3” (59mm)
2-1/3” (59mm)
2-1/24”(52mm)
2-1/24”(52mm)
1-3/8”(35mm)
1-3/8”(35mm)
1-1/6”
1-1/6”
17/24” (18mm)
17/24” (18mm)
(29.6mm)
(29.6mm)
1/4”(6.4mm)
1/4”(6.4mm)
1-3/4”(44.5mm)
1-3/4”(44.5mm)
3”(76.2mm)
3”(76.2mm)
0-1/8” (3 mm)
DOOR SWING AT 115° OPENING
1-1/4” (32 mm)
1-1/2” (38 mm)
11 3/4”
(298 mm)
Max
1” (25 mm)
Page 9 of 10

HINGING DETAILS 90° OPENING
Available for the following models:
• K 28x1 Vi
• KF 28x1 Vi
1-1/4” (32 mm)
1-3/4” (44 mm)
1-1/2” (38 mm)
2” (51 mm)
0-3/4” (19 mm)
1” (25 mm)
Fully Integrated
30” MasterCool II
7/16”
(11 mm)
1-3/16”
(30mm)
1-7/16”
(36.5mm)
1-11/16”
(43mm)
1-15/16”
(49.2mm)
0-1/8” (3 mm)
Handle or object that is
NOT ush with Cabinet
Front.
DOOR SWING AT 90° OPENING
0-3/4” (19 mm)
1” (25 mm)
1-1/4” (32 mm)
1-1/2” (38 mm)
7/16” (11 mm)
/16” (830 mm)
11
32
When installing hinge side next to an appliance or object that is within range of the door panel,
limit the door opening angle to 90°. This is done by installing the banking pin as illustrated.
Insert the banking pin through the holes and drive in with a hammer.
Specification Sheets TRS 04252019
Page 10 of 10