Miele G 5975 User Manual

Operating Instructions

Dishwasher
G 5970
G 5975

To prevent accidents
and appliance damage
read these instructions

before

installation or use.

en - US, CA

M.-Nr. 07 909 280

Contents

IMPORTANT SAFETY INSTRUCTIONS.................................4

Guide to the dishwasher ............................................8

Control panel ......................................................9

Caring for the environment.........................................10

Before using for the first time.......................................11

To open the door ..................................................11

Display function ...................................................12

Welcome screen ..................................................13

Language setting..................................................13

Clock format......................................................13

Filling the salt container .............................................16

Salt refill message .................................................17

Rinse aid ........................................................18

Adding rinse aid ..................................................18

Rinse aid indicator .................................................19

Loading the dishwasher ...........................................20

Items not recommended for dishwashing ...............................21

Typical load for 10 place settings .....................................22

Typical load for 16 place settings .....................................23

Upper basket .....................................................24

Lower basket .....................................................28

Cutlery ..........................................................31

Optional accessories..............................................33

Use ............................................................34

Adding detergent..................................................35

Turning on .......................................................36

Selecting a program ...............................................36

Selecting options ..................................................39

Starting a program.................................................40

Time display......................................................40

Standby .........................................................41

At the end of a program.............................................41

Preparing your appliance for an extended vacation .......................42

Interrupting a program..............................................42

Changing a program ...............................................43

2

Contents

Additional options ................................................44

Delay start .......................................................44

BrilliantLight ......................................................46

Settings

Water hardness ...................................................49

Drying Plus.......................................................50

Optimize standby..................................................51

Refill display......................................................51

Check filters ......................................................51

Reorganize programs ..............................................52

Save options .....................................................53

Keypad tone .....................................................54

Brightness .......................................................54

Memory .........................................................54

Factory default ....................................................55

RemoteVision ....................................................56

Frequently asked questions ........................................57

Technical faults ...................................................57

Problems water intake/drain .........................................59

General problems with the dishwasher .................................61

Sounds..........................................................63

Poor cleaning results ...............................................64

After sales service ................................................67

Transport .......................................................68

User Maintenance Instructions......................................69

Cleaning and Care ................................................70

Triple filter system .................................................72

Cleaning the drain pump and non-return valve...........................76

Installation instructions ...........................................77

Help to protect the environment.....................................78

Electrical connection..............................................79

Plumbing........................................................81

Connection to the water supply ........................................81

Drainage ........................................................82

! .......................................................47

3

IMPORTANT SAFETY INSTRUCTIONS

WARNING –

When using your dishwasher, follow
basic precautions, including the
following:

Read all instructions before
installation or use of the dishwasher
to prevent injury and machine
damage.

Use the dishwasher only for its
intended purpose. This appliance is
intended for residential use only.

Keep these operating instructions in
a safe place and pass them on to
any future user.

Correct usage

The dishwasher is not designed for

~

commercial use. It is intended for use in
domestic households and in similar
working and residential environments
such as, shops, offices and showrooms
or guest houses.

The dishwasher is not intended for

~

outdoor use.

It must only be used as a domestic

~

appliance as specified in these
operating instructions, for cleaning
domestic crockery and cutlery. Any
other usage is not supported by the
manufacturer and could be dangerous.

Persons who lack physical, sensory

~

or mental abilities, or experience with
the appliance should not use the
dishwasher without supervision or
instruction by a responsible person.

Electrical Safety

Before installation, make sure that

~

the voltage and frequency listed on the
data plate correspond with the
household electrical supply. This data
must correspond to prevent injury and
machine damage. Consult a qualified
electrician if in doubt.

Before installation or service,

~

disconnect the power supply to the
work area by unplugging the unit,
"tripping" the circuit breaker or
removing the fuse.

Do not use an extension cord to

~

connect this appliance to electricity.
Extension cords do not guarantee the
required safety of the appliance (e.g.
danger of overheating).

Be certain your appliance is

~

properly installed and grounded by a
qualified technician. To guarantee the
electrical safety of this appliance
continuity must exist between the
appliance and an effective grounding
system. It is imperative that this basic
safety requirement be met. If there is
any doubt, have the electrical system of
the house checked by a qualified
electrician.

If the supplied power cord is

~

damaged it must only be replaced by a
Miele Service technician with a genuine
Miele power cord.

The outlet must be accessible at all

~

times after installation to disconnect the
dishwasher.

4

IMPORTANT SAFETY INSTRUCTIONS

Installation

The dishwasher must be installed

~

and connected in accordance with the
installation instructions.

Installation and repair work should

~

be performed by a Miele authorized
service technician. Work by unqualified
persons could be dangerous and may
void the warranty.

Do not install or use a damaged

~

dishwasher. A damaged appliance is
dangerous. Unplug the machine and
contact the Miele Technical Service
Department.

Ensure that any plastic wrappings,

~

bags, etc. are disposed of safely and
kept out of the reach of children.
Danger of suffocation!

This appliance must not be used in

~

a non-stationary location (e.g. on a
boat).

, WARNING - Fire hazard!

~

Do not cover or crush the plug of the
appliance. Ensure that the cabinet
opening for the dishwasher provides
ample space for the plug and cord.
Installing the dishwasher in a tight
space may crimp the power cord or put
pressure on the plug which could
cause overheating.

Do not install this dishwasher

~

beneath a cooking surface, oven or any
appliance that radiates heat.
High temperatures from these units
may damage the dishwasher.

A toe-kick must be used with the

~

dishwasher. If the supplied toe-kick is
not used, a cabinet matching toe-kick
must be installed.

Do not install the dishwasher in an

~

area where it will be exposed to
temperatures below freezing.

Do not cut the intake hose or

~

submerge it in liquid. This hose
contains electrical components that
could cause injury or property damage
if cut or submerged.

Only power up the dishwasher

~

when all installation and plumbing work
is complete.

This dishwasher should only be

~

installed under a continuous counter
top secured to adjacent cabinetry.

5

IMPORTANT SAFETY INSTRUCTIONS

Use

To reduce the risk of injury, do not

~

allow children to play in, on or near the
dishwasher. It is possible for small
fingers may be pinched in the door.

Only use the dishwasher if all panels

~

are properly in place.

Do not tamper with the controls.

~

Do not sit or stand on the door or

~

baskets of the dishwasher. Close the
door when not in use.

Under certain conditions, hydrogen

~

gas may be produced in a hot water
system that has not been used for two
weeks or more. HYDROGEN GAS IS
EXPLOSIVE. If the hot water system has
not been used for such a period, turn
on all hot water faucets and let water
flow from each for several minutes
before using the dishwasher. This will
release any accumulated hydrogen
gas. Do not smoke or use an open
flame during this time.

Be sure that all items placed in the

~

dishwasher are "dishwasher safe". For
items not labeled, check the
manufacturer’s recommendations.

When loading tableware, place

~

sharp items away from the door to
prevent damage to the seal. Load
sharp items pointing downwards to
prevent injuries.

Only use detergents and rinse aids

~

recommended for residential
dishwashers. Keep all detergents and
rinse aids out of the reach of children.

Do not inhale or swallow detergents.

~

Dishwasher detergents contain irritant
and corrosive ingredients. They can
cause burning in the mouth and throat if
swallowed, or inhibit breathing. Consult
a doctor immediately if detergent has
been swallowed or inhaled.

Do not drink water from the

~

dishwasher! Harmful residues could be
present.

Do not fill the rinse aid reservoir or

~

salt container with detergent. It will
destroy the rinse aid compartment and
water softener.

If the supplied power cord is

~

damaged it must only be replaced by a
Miele Service technician with a genuine
Miele power cord.
The outlet must be accessible at all
times after installation to disconnect the
dishwasher.

This model offers a Drying Plus

~

feature, i.e. the door will automatically
open, without an audible signal first
being given, at the end of the program
releasing warm air from the dishwasher.
Use caution, the air may be hot!

6

IMPORTANT SAFETY INSTRUCTIONS

This model offers a Drying Plus

~

feature, i.e. the door will automatically
shut once close enough to engage the
catch.

Advise the user of the Drying Plus

~

feature to avoid injuries by walking,
bumping or knocking into the partially
opened door.

Supervise children near the

~

dishwasher to ensure fingers or other
parts of the body are not caught when
the Drying Plus feature is in operation.

Dishes can be very hot at the end of

~

a program. Allow the dishes to cool
until they are cool enough to handle
before unloading them.

The water supply must be turned off

~

when the appliance is not used for a
longer period of time (e.g. during
vacations).

Disposal of an appliance

If the appliance is removed from its

~

installation site and will not be used,
remove the doorlock to the wash
cabinet to prevent children from locking
themselves in the machine.

SAVE THESE

INSTRUCTIONS

7

Guide to the dishwasher

a Upper spray arm (not visible)

b Cutlery tray

c Upper basket

d Middle spray arm

e Air inlet for drying

(depending on model)

f Lower spray arm

8

g Triple filter system

h Data plate

i Optical interface

j Rinse aid reservoir

k Dual compartment detergent

dispenser

l Salt container

Control panel

Guide to the dishwasher

a Selection buttons

To select a menu point from this
display, to change the displayed
value (+/-) or to browse between
menus.

b Display

See the following pages for more
information.

c U (Clear) button

To switch back to the previous menu
level or to discard a selected setting.

d d Delay Start button with indicator

e K button (Information)

To display more info about the
displayed menu

f K On/Off button with indicator

To turn the dishwasher on or off.

g Technical Service interface

Allows a service technician to check
and update the machine when
applicable.

h Optical interface

To show the current wash cycle
status when the door is closed

i RemoteVision

Indicator for RemoteVision enabled
appliances.

This operating instruction manual describes several dishwasher models with
different indicated settings.
The different dishwasher models are named :

Standard =32
XXL =33

1

/16" (81.5 cm) high dishwashers

11

/16" (85.5 cm) high dishwashers.

9

Caring for the environment

Energy saving washing

This dishwasher is exceptionally
economical in the use of water and
electricity. For best results follow these
tips:

For lowest energy consumption you

^

may connect the dishwasher to a
cold water source.

For fastest possible wash times, with

^

slightly higher energy consumption,
connect the dishwasher to a hot
water source.

Make full use of the baskets without

^

overloading for the most economical
washing.

^ Use the correct amount of detergent

and rinse aid. Detergent dosage is
dependent upon the amount of
soiling and type of dishware being
washed. See the "Program Guide" for
more information.

^ When using powder or gel detergent,

reduce the amount to
normal amount when washing a small
load.

^

Choose a program that best suits the
degree of soiling and the type of
dishes being washed.

10

2

/3of the

Before using for the first time

To open the door

The door will open automatically at the
end of the program to aid in the drying
process.

This function can be deactivated (see
"Settings - Drying Plus").

^ Pull the handle to open the door.

If the door is opened during operation,
the rinsing function is automatically
canceled.

To close the door

Push the baskets in.

^

Lift the door and push until the catch

^

engages.

The door will then close automatically.

Keep fingers and other body

,

parts away from the door as it is
closing. Danger of injury.

,

Keep the opening area free of

obstructions.

11

Before using for the first time

Display function

The following can be selected in the
display:

the wash program

–

the options

–

the start time

–

the settings menu

–

information

–

!

During a running program the display
shows:

– the program name
– the current time of day
– the program sequence
– the approximate remaining time
– faults and messages

To save energy the dishwasher turns
off after a few minutes if no button is
pressed. To turn the dishwasher
back on press K.

!

A bullet in the display next to the button
shows that this function can be
selected.

n

The arrows in the display indicate that
more selections or text follow and can
be displayed with the respective
control.

-----­A dotted line is shown to indicate the
last selection available.

OK

To confirm these messages or settings
select OK, and the next menu or
another menu level will appear.

(

The currently selected option is marked
with a check.

The "Settings !" menu allows you to
customize the dishwasher settings.
See "Settings" for more information.

12

Welcome screen

Language setting

Before using for the first time

Turn the dishwasher on K.

^

A Welcome screen shows when the washer is turned on for
the first time.

The display changes automatically to the language setting.

Clock format

}#eština
} dansk

Select the desired language and confirm with OK.

^

Sprache F

The selected language is marked with a L check.

The display changes automatically to the clock format.

} 12 h clock
} 24 h clock B

Clock Format

^ Select the desired setting and confirm with OK.

e

OK }

13

Before using for the first time

Time of day

The display changes automatically to the time of day setting.

Water hardness

} +
} -

Set the hours using the +/- controls and confirm with OK.

^

Please set the time of day OK }

12

:00

Set the minutes and press OK.

The display then changes to the water hardness setting.

} 15°d B
} 16°d

Water hardness

e

OK }

To achieve good cleaning results, the dishwasher needs soft
water. Hard water results in calcium deposits on dishware
and in the dishwasher.
If your tap water hardness is above 4 °d (4 gr/gal [US]), the
water should be softened.

– Your local water authority will be able to advise you of the

water hardness level in your area.

–

The dishwasher must be programmed to correspond to the
water hardness in your area.

14

–

In areas where the water hardness fluctuates (e. g.
37 - 50 °d [39 -52 gr/gal]) always program the machine to
the higher value (in this example 50 °d [52 gr/gal]).

If there is a fault, it will help the service technician to know the
hardness of your local water supply.

Please note your water hardness below:

°d (gr/gal)

Before using for the first time

The water hardness was programmed
at 1 °d (1 gr/gal) by factory default.

Select the hardness of your water

^

supply and confirm with the center
button.

See "Settings - Water hardness" for
more information.

Two notes appear in the display.

After confirming these notes,

rinse aid

and/or : Add salt may

: Add

appear in the display.
Confirm these notes with OK. The
display changes to the main menu.

These basic settings are saved after
the first full program cycle is
completed.

15

Before using for the first time

Every dishwasher is tested before
leaving the factory. Any water
remaining in the machine is from the
final factory test and does not
indicate that the machine has been
used.

Remove the lower basket from the

^

wash cabinet and unscrew the salt
container lid.

When opening the salt container,
water will run out. Open the
container only to refill salt.

Filling the salt container

To achieve good cleaning results, the
dishwasher needs soft water (water that
is low in minerals). Hard water results in
calcium deposits on dishware and in
the dishwasher.
Therefore, if your tap water hardness is
above 4 °d (4 gr/gal) the water should
be softened. The built-in water softener
is designed for this purpose. The water
softener is suitable for a water hardness
up to 70 °d (73 gr/gal).

,

Inadvertently filling the salt
container with dishwashing
detergent (including liquid
detergent) will damage the water
softener.

,

Only use water softener salt
specially formulated for
dishwashers. Other salts may
contain insoluble additives which
can impair the water softener.

Important: The salt container must
be filled with 2 quarts (2 l) of water

before adding salt for the first time

so the salt can dissolve
properly. Water does not have to be
added with subsequent refills.

If using "Tab" products which
include salt, still add salt to the
machine to achieve optimal cleaning
results and ensure long-term
functioning of the water softener.

16

Place the provided funnel over the

^

salt container and carefully fill it with
salt. The salt container holds
approx. 4.4 lbs (2 kg) of salt,
depending on the type of salt.

Before using for the first time

Salt refill message

When the display shows Insufficient

^

salt, refill the salt after the program
has finished.

Confirm with OK.

^

The message will clear from the display.

If a sufficiently high concentration of
salt has not yet formed, the Insufficient
salt message may continue to be
displayed after adding the salt. In this
case, confirm again with the center
button.

The Insufficient salt message is turned
off if you have programmed the
dishwasher to a water hardness below
4 °d (4 gr/gal).

^ Clean any excess salt from the

threads of the container opening.
Screw the lid on firmly.

^ Immediately after each refill, run the

"Rinse & Hold" program (without the
Turbo function) without a load. This
will remove any traces of salt from
inside the wash cabinet.

,Immediately after each refill, run

the "Rinse & Hold" program (without
the Turbo function) without a load.
This will remove any traces of salt
from inside the wash cabinet.

If using"Tab" detergent products in
your dishwasher, the messages can
be turned off if desired (see "Settings

- Deactivate indicators").

If you switch to using detergent that
does not contain salt or rinse aid, it
is important to remember to
replenish the salt and rinse aid and
to turn the indicators back on.

17

Before using for the first time

Rinse aid

Rinse aid helps to prevent spotting on
dishes and glassware.
The rinse aid is filled in the reservoir
and the set amount will be
automatically dosed.

Filling the rinse aid reservoir with

,

detergent (liquid or powder) will
damage the reservoir. Only pour
rinse aid formulated for residential
dishwashers into the reservoir.

When using "Tab" detergents rinse
aid is not needed.

Adding rinse aid

Press on the flap until you hear it

^

click shut. Failure to close it all the
way allows water to enter the
reservoir during the wash program.

^ Clean any spilled rinse aid. This

prevents over-foaming occurring
during the next program.

^

Press the button on the rinse aid
reservoir in the direction of the arrow
until the flap springs open.

^

Pour liquid rinse aid into the reservoir
until it is visible on the surface of the
screen.

The rinse aid reservoir holds
approximately 3.7 fl. oz. (110 ml).

18

You can adjust the rinse aid dosage
for best results (see "Settings - Rinse
aid").

Rinse aid indicator

When the ( Refill rinse aid message
appears, the reservoir contains
sufficient rinse aid for2-3programs
only.

Add rinse aid once the program has

^

finished.

Before using for the first time

Confirm with the

^

The "Refill rinse aid" message will go
out.

If using "Tab" detergent products in
your dishwasher, the messages can
be turned off if desired (see
"Settings - Deactivate indicators").

If you switch to using detergent that
does not contain salt or rinse aid, it
is important to remember to
replenish the salt and rinse aid and
to turn the indicators back on.

OK button.

19

Loading the dishwasher

Do not wash items soiled with

,

ash, sand, wax, grease or paint in
the dishwasher.
Ash and sand do not dissolve and
will be distributed throughout the
inside of the dishwasher.
Wax, grease and paint will cause
permanent discoloration and
damage to the dishwasher.

Scrape food from dishes before

^

placing them in the dishwasher,
rinsing is not necessary.

^ Some foods contain natural dyes,

e.g. carrots or tomatoes. Plastic items
may discolor permanently if they
come in contact with food dyes.

^ All items can be placed anywhere in

the baskets.

^ Load dishes so that water can reach

all surfaces. Do not place dishes or
cutlery inside other pieces.

The spray arms must not be blocked

^

by items that are too tall or hang
through the baskets. Check
clearance by manually rotating the
spray arms.

Place very small items in the cutlery

^

tray or basket so they do not fall to
the bottom of the wash cabinet.

Food residue and spilled liquids

^

should be cleaned from the sides of
the dishwasher door. These are
outside of the wash cabinet and are
not cleaned by water from the spray
arms.

^

Make sure that all items are securely
positioned.

^

Hollow items such as cups and
glasses should be placed upside
down in the baskets.

^

To ensure good water coverage, tall,
narrow and hollow items, i.e. vases
or champagne glasses, should be
placed in the center of the basket
rather than in the corners.

^

Concave based items such as mugs
or bowls, should be placed at an
angle so that water does not pool.

20

Loading the dishwasher

Items not recommended for
dishwashing

Cutlery with wooden handles

–

Wooden cutting boards

–

Glued items such as old knives with

–

handles glued together around the
shank of the blade

Handmade craft items, antique,

–

metal trimmed or decorative
glassware

Plastic items that are not heat

–

resistant

– Copper, brass, tin or aluminum

– Dishes with color painted over the

glaze. These dishes may fade over
time

– Fine glassware and crystal items

should only be washed using the
"China & Crystal" program*.
Otherwise clouding or etching may
occur after frequent washing.

–

Cast iron pots and pans

* depending on model

Glassware:

There are no standard guidelines for

–

washing glassware, when in doubt
wash by hand.

When purchasing new dishes,

–

glasses and cutlery, make sure they
are dishwasher safe. Only wash
items marked "dishwasher safe" in
the dishwasher.

If fine glassware is washed in the

–

dishwasher select the "China &
Crystal" program*. This will reduce
the risk of clouding.

Silver and aluminum:

– Silver or aluminum items may tarnish.

– Silverware previously cleaned with a

silver polish may be damp or spotted
at the end of a program where water
has adhered to the polish. This can
be rubbed off with a soft, dry cloth.
Silver that has been cleaned in an
immersion dip is usually dry at the
end of a program, but may tarnish.

–

If left to dry, foods containing sulfur
can discolor silver. These include
egg yolk, onions, mayonnaise,
mustard, fish and marinades.

If unsure whether your china and
crystal are dishwasher safe, please
check with the manufacturer. The
China & Crystal program*, although
extremely gentle and thorough can
cause the china and crystal to "wear"
if they are not dishwasher safe.

–

Silverware may tarnish or pit if
washed next to stainless steel.
Leave space between these metals.

–

Clean aluminum items, e.g. grease
filters, with domestic dishwasher
detergent only.

21

Loading the dishwasher

Typical load for 10 place settings

Upper basket Lower basket

Cutlery tray

22

Loading the dishwasher

Typical load for 16 place settings

Upper basket Lower basket

Cutlery tray

23

Loading the dishwasher

Upper basket

Always use the dishwasher with

,

the upper and lower basket inserted
(except during the
program, if available).

^ Load the upper basket with small,

lightweight, or delicate items such as
cups, saucers, glasses, dessert
bowls, etc.
Shallow pans can also be placed in
the upper basket.

^

Long items such as soup ladles,
mixing spoons and long knives
should be placed lying down across
the front of the upper basket.

Tall items

Foldable spikes

The rows of spikes can be lowered to
make more room for larger items, such
as casserole dishes.

^ Press the yellow lever down a and

fold down the spikes b.

Hinged cup rack

^ To make room for tall items, raise the

rack upwards.

Glasses can be arranged along the cup
rack to give them some support during
the program.

^

Lower the cup rack and lean the
glasses against it.

24

Loading the dishwasher

Jumbo cup rack

(depending on model):

The cup rack can be set at two different
widths so that it can also accommodate
large cups.

^ Pull the cup rack upwards and click it

back into position at the required
width.

Universal support bar

The support bar will hold tall glasses
and stem ware securely.

^ Fold the bar down and lean the

desired glasses against it.

^ If desired, a section of the cutlery tray

can be removed to allow for even
taller glasses.

25

Loading the dishwasher

Adjusting the height:

You can set the support bar at two
different heights.

^ Pull the support bar upwards and

click it back into position at the
required height.

Use the low setting for small glasses
and tumblers.

Use the high setting for tall glasses and
stem ware.

26

Loading the dishwasher

Adjusting the upper basket

In order to gain more space for taller
items the upper basket can be adjusted
on three levels with 2 cm between each
level.

The upper basket can also be set at an
angle with one side high and the other
side low. Make sure, however, that the
basket can slide smoothly in and out of
the cabinet.

Slide out the upper basket.

^

To adjust the upper basket downwards:

Pull up on the levers at the sides of

^

the upper basket.

Adjust the basket to the desired

^

height and then release the levers to
lock the basket in place.

Depending on the setting of the upper
basket, the following plate dimensions
can be accommodated.

Depending on the setting of the upper
basket, a variety of plate dimensions
can be accommodated.

To adjust the upper basket upwards:

^

Lift the basket up until it clicks into
place.

27

Loading the dishwasher

Lower basket

For larger and heavier items such as

^

plates, serving platters, saucepans,
bowls, etc.
Glasses, cups, small plates and
saucers can also be arranged in the
lower basket.

Dishwasher with cutlery tray

Place large platters and dishes in the

^

center of the lower basket.

When tilted, plates up to 13 3/4"
(35 cm) in diameter can be

accommodated.

Heavily soiled items

28

Loading the dishwasher

Removable MultiComfort insert

The rear section of the lower basket is
used for cups, glasses, plates, pots
and pans.

You can remove the MultiComfort insert
to provide more space for larger items
such as pots and pans.

To remove the insert a

^ Press the yellow handle forwards and

remove the insert.

To replace the insert b

Glass rack

The glass rack can be raised to make

^

more room for tall items.

Stem glassware, e. g. wine glasses,

^

champagne flutes or beer glasses,
can be leaned against the glass rack
or suspended from it.

The height of the glass rack is
adjustable.

^ Slide the glass rack to the desired

height until the catches click into
place at the top.

^

Slide the hooks of the insert under
the struts of the lower basket.

^

Push down on the insert to snap it
into position.

29

Loading the dishwasher

Universal support bar

The support bar will hold tall glasses
and stem-ware securely.

^ Fold the bar down and lean the

desired glasses against it.

^ If desired, a section of the cutlery tray

can be removed to allow for even
taller glasses.

Foldable spikes

The rows of spikes can be lowered to
make more room for larger items, such
as casserole dishes.

^ Press the yellow lever down a and

fold down the spikes b.

Vase / Bottle insert

The vase / bottle insert can be used to
rinse narrow items, e.g. vases, baby
bottles, etc.

30

^

Pull the insert up a and bend to the
side b, if not needed.

Cutlery

Split cutlery tray

(depending on model)

^ Arrange the cutlery as shown in the

cutlery tray.

For easier unloading cutlery should be
grouped in zones, one for knives, one
for forks, one for spoons, etc.

Loading the dishwasher

Spoons with thick handles may have to
be placed as knives and forks with their
heads in the holders.

Spoon heads should be placed in
contact with at least one of the serrated
retainers on the base of the cutlery tray
to ensure that water runs off them
freely.

The upper spray arm must not be
blocked by tall cutlery items (e.g.
cake servers).

The side sections of the tray can be
moved into the middle to accommodate
tall dishware items in the upper basket.

^

You can use the yellow slide to adjust
the height of the middle section of the
cutlery tray to make more room for
large items of cutlery.

31

Loading the dishwasher

Cutlery basket

(depending on model)

The cutlery basket can be placed
anywhere on the front rows of spikes in
the lower basket.

^ To avoid risk of injury, knives and

forks should be placed with the
handles upwards in the basket.
However, cutlery placed handle
down in the basket will come out
cleaner and drier.

Cutlery insert for the cutlery basket

Use the insert supplied for heavily
soiled items of cutlery.
The insert separates the items so that
they can be reached better by the
spray jets.

^ Fit it onto the cutlery basket if

required.

^

Place small items of cutlery in the
individual slots on three sides of the
cutlery basket.

32

^

Insert cutlery with the handles facing
downwards, and distribute them
evenly along the insert.

Optional accessories

Optional dishwasher accessories are available from your Miele dealer, Miele or
Mieleusa.com (depending on your model some may already be supplied with your
machine as standard).

If you would like to... the following accessory will need

to be ordered...

...wash a Miele Cappuccinatore ... a Cappuccinatore insert for the

upper basket.

...wash additional items of cutlery ... a cutlery basket for the lower

basket.

...wash long-stemmed glassware ... a glassware rack for the lower

basket.

MieleCare Collection

Miele branded cleaning and care products, including dishwasher salt, detergent
and rinse aid, are available to order from your Miele dealer, Miele or the on-line
Miele store www.mieleusa.com

33

Use

Detergent

Dishwasher detergents contain

,

irritant and corrosive ingredients.
Avoid inhaling or swallowing
dishwasher detergent.
Keep children away from detergent.
Keep detergent out of the reach of
children. Keep children away from
the dishwasher when the door is
open. There could still be detergent
residues in the dishwasher. Only
add detergent just before starting
the program and lock the door with
the child safety lock (depending on
model).

Only use detergents formulated

,

for domestic dishwashers.

Use only the recommended amount
of detergent. Continued use of too
much detergent may cause machine
damage.

You can use powder, gel or tab
detergents. Follow the dosage
information on the detergent
packaging.
If using a Tab detergent see "Settings ­Deactivate indicators".

Detergent tabs are not recommended
for use with the program "Express"
(depending on model). The tabs may
not dissolve completely.

Dishwasher cleaning products are
available from MIele.

When using the "China & Crystal"
program (depending on model)
reduce the amount of detergent
used to at least ½ of the normal
dosage. Also make certain your
china and crystal are dishwasher
safe.

34

Adding detergent

^ Press the latch on the detergent

dispenser. The flap will spring open.

The flap is always open at the end of a
program.

Use

Add detergent to the compartments

^

and close the container flap.

^ Use one tab or add powder or gel

detergent to compartment II and
close the flap.

^ If a Pre-rinse is desired, and

available for your chosen program,
add 1 teaspoon (5 ml) of detergent to
compartment I.

Compartment I holds a maximum of 2
teaspoons (10 ml),
compartment II holds a maximum of 3.5
tablespoons (50 ml) of detergent.

The horizontal marks in compartment II
indicate the levels of approximately 1 ¼
and 2 tablespoons (20 and 30 ml)
respectively. The marks indicate the
approximate fill level in ml when the
door is open in a horizontal position.

35

Use

Turning on

Open the water supply, if closed.

^

Open the door.

^

Make sure the spray arms can rotate freely.

^

Turn the dishwasher on K.

^

The main menu shows in the display.
If the memory function is selected, the last selected program
is displayed. See "Settings J - Memory".

} Sensor Wash

Selecting a program

Choose your program according to the type of load and
soiling.

The "Program guide" describes the programs and
application.

^ Select the desired program.

The display changes to the program menu.

Sensor Wash 1:32 h
} Options

Information about the selected program can be displayed
by pressing the K button.

To choose another program use the U (Clear) button to
return to the main menu.

Main menu

r} Express

12:00

Start }

36

Program guide When to use Program sequence

Pre-rinse Main

wash

12 1 2

Interim

rinse

Final
rinse

Use

Drying

Pots & Pans For normally soiled pots &

pans with dried on food, and
heavily soiled dishware, use
120% detergent
recommended.

Normal Program for completely

washing a full load of
normally soiled dishware with
the ability to adjust energy and
water consumption based on
the soil load of the dishware.

China & Crystal For temperature sensitive

glassware and lightly soiled
dishware, use 50% detergent
recommended.

SaniWash To sanitize dishware, e.g.

baby bottles, cutting boards
and preparation dishware.

Extra Quiet Very quiet program for

normally soiled dishware

with dried on food.

Rinse & Hold To rinse dishes when a

complete program is not
needed.

Express "Quick program" for lightly

soiled dishware, e.g. party
dishware or to remove salt
traces from the wash cabinet
after refilling salt; not suitable
for detergent tabs

Heavy Soil For heavily soiled dishware

with dried starchy food

Light For lightly soiled dishware,

e.g. party dishware

XX X X X

as

required

as

requ

ired

X

XXX XX

XX XX

X as required X X

XXXX

XX XX

XX XX

XX XX

37

Use

Program guide When to use Program sequence

Pre-rinse Main

wash

12 1 2

Interim

rinse

Final
rinse

Drying

Energy Saver The water intake temperature

Sensor Wash Sensor controlled program for

Starch/Cheese For dishware with dried on

Plastics To gently clean dishwasher

Tall Items For extra large, heat resistant

Glass no rinse aid
cold

Glass no rinse aid
warm

must be 115°F (45°C) for light

to normally soiled dishware

normally soiled dishware

starchy or cheesy food; 120%
detergent recommended

safe plastics and plastic toys

items, e.g. large vases.
Remove upper basket

For a quick cleaning of
glassware for direct reuse; use
without detergent and rinse
aid

To wash glassware without
detergent and rinse aid; rinse
cycle with warm water

Usage:

Electric: 0.01 - 1.3 kWh
Water: 1.1-5gal(4-19l)

XX XX

as

requ

ired

XXX XX

XXX XX

XXX XX

X as required X X

XX X

XX X

38

Use

Selecting options

Options can be added to the selected
program.

Select the Options menu.

^

The display shows the available options
for the selected program.

Available options:

Turbo:

For shortening the program duration.

–

To achieve optimum results, energy
consumption rates will increase.
When the "Turbo" function is used in
correlation with a program a quick
rinse is completed without heating.
Use when a complete program is not
needed.

Pre-rinse:

– For easily removable soiling

Soak:

– To soak stubborn soiling.

When using powder detergent, fill
approx. 1 teaspoon (5 g) of
detergent in detergent
compartment I.

Intensive lower basket:

For washing heavily soiled dishes in

–

the lower basket at the same time as
delicate items in the upper basket.
This function will increase the
cleaning power in the lower basket in
programs which it is selected.
Depending on the program, the run
time may be extended slightly.
Once this function is set for a
program it will remain active for that
program until the setting is changed.

Select the desired options.

^

The selected options are marked with a

L check.

^ To de-select an option press the

respective control again.

^ Confirm the selected options with

OK.

The display changes back to the
program menu. The message Options
selected will appear in this display.

Extended drying:

–

To enhance drying of odd shaped
dishware and plastic items.

39

Use

Starting a program

Select Start.

^

The display shows Close the door.
To select another program or to add
options, select Back and cancel the
program with Cancel.

Start the program by closing the

^

door.

The optical interface lights to indicate
that a program is running.

The program starts and "Items can be
added" appears in the display.
As long as this reference is shown,
tableware can be added to the
machine without impairing the cleaning
result.

,The water in the dishwasher is

hot, risk of burns by splashing water.

Cancel a program only in the first
few minutes. Otherwise important
program steps (e.g. the water
softening) could be interrupted.

Time display

Before the program starts, the time
display shows the running time of the
selected program in hours and minutes.
During the running program the
remaining time is shown in the time
display.

The running time for the same program
may vary depending on the intake
water temperature, load size and
soiling.

When a program is selected for the first
time, a time is shown which equals an
average program running time with
cold water.

Each time a program is run, the
electronic adjusts the program running
time according to the intake water
temperature and the load size.

40

Use

Standby

A few minutes after the last key is
pressed or at the end of the program
the dishwasher switch into Standby
mode to save energy.

To turn the dishwasher back on press

^

K.

This feature can also be turned off (see
"Settings - Optimize standby"). The
dishwasher will then turn off after
6 hours.

If refill salt and/or rinse aid or a fault
are present in the display, the
dishwasher will not turn off.

The refill messages can be turned
off when you use a tab detergent
(see "Settings-Refill display").
Fault messages cannot be turned
off.

At the end of a program

At the end of a program the optical
control light flashes slowly with the door
closed.

The optical function light goes out one
hour after the end of a program.

At the end of a program the display
shows Program finished or Drying plus
with the door slightly open (if activated).

In the "Express" program, the drying
fan will run for a few minutes after
the program is completed.

Dishes tend to chip if removed

,

still hot from the dishwasher. If the
automatic door opening setting is
deactivated (see "Settings - Drying
plus") it is recommended to open the
door manually to allow tableware to
cool much faster.

^ The dishes can now be removed.

Unloading the lower basket first will
prevent water drops from the upper
basket and cutlery tray (depending on
model) from dropping onto dishes in
the lower basket.

^

Push the baskets in.

^

Turn the dishwasher off K.

The dishwasher continues to use
electricity until turned off with the K
button. After a few minutes the
dishwasher will turn off
automatically.

41

Use

Preparing your appliance for
an extended vacation

If you elect to turn off the water to your
home for an extended period of time,
please note that this may not be
enough to reduce the risk of a leak.

To be completely safe, you must
turn off the water supply to each
individual appliance. This means
under the sink for a dishwasher, at
the laundry bib for your washer, etc.

Interrupting a program

A program is interrupted as soon as the
door is opened. If the door is closed,
the program will continue from where it
was interrupted.

Open the door with care. The

,

water in the dishwasher is hot.
Danger of scalding. Before closing
the door again, leave it ajar for
approx. 20 secs. This will enable the
temperature in the wash cabinet to
settle. Close the door firmly until it
clicks into place.

42

Changing a program

If the detergent flap is already open, do not change the
program.

If a program has already started and you wish to change it:

Open the door.

^

Use

Sensor Wash 1:32Std
Main wash

Select Cancel and confirm with OK.

^

The program is canceled.

Sensor Wash
Program finished

Main menu }

^ Select Main menu.

The display changes to the main menu.

^ Select the desired program.

^

Select Start.

^

Start the program by closing the door.

The optical interface lights. The program starts.

12:00

Cancel }

12:00

43

Additional options

Delay start

The starting time of a program can be delayed between 15
minutes and 24 hours. The start can be delayed in
15-minute-increments.

When using the "Delay Start" function make sure that the
detergent compartment is dry before adding detergent,
use a cloth if necessary. The detergent might stick
together and not get completely rinsed out.
Do not use liquid detergent when selecting "Delay Start",
the detergent could leak out of the compartment.

,

dishwasher door to prevent children from coming in
contact with the detergent.

^ Open the door.

^ Turn the dishwasher on K.

The K indicator lights.

It is recommended to add the detergent and lock the

44

^ Select the desired program.

^ Select "Delay start,".

The display shows the current time of day and the last
selected Start time, The program end time is also shown.
The indicator , lights.

} +
} -

^

Select the desired Start time with the +/- buttons. Holding

Start time

End at

12:00

13:32

12:00

OK }

the button will automatically increase or decrease the time.
The end time will be automatically adjusted.

^

Confirm with

OK.

Additional options

The display changes to the program menu.

Select Start.

^

Close the door.

^

The program starts automatically at the selected time.
The indicator , goes out.

A few minutes after the last key press, the dishwasher will
switch into standby mode to save energy. The display and
the indicators will turn off.

Starting a program before the delay start has elapsed:

A program can be started before the delay start time has
elapsed.

^ Open the door.

^ Select Cancel and confirm with OK.

The d indicator lights.

Sensor Wash
Program finished

Main menu }

12:00

^ Select Main menu.

^

Select the desired program.

^

Select Start.

^

To start the program, close the door.

The optical interface lights to indicate that a program is
running.

45

Additional options

BrilliantLight

The dishwasher is equipped with an
interior light. With the door open the
light turns off automatically after
15 minutes

The light can also be turned off.

Open and close the door quickly 3

^

times. The door must be opened
enough so that the interior lighting
turns on then off.

From now on the interior lighting is
turned off.

^ To turn the light on again, repeat the

above process.

46

Settings !

The "Settings J" menu allows you to adjust standard settings

Opening the Settings J menu

Turn the dishwasher on K.

^

The main menu shows in the display.
If the memory function is selected, the last selected program
is displayed. See "Settings J - Memory". Switch to the main
menu by pressing "Clear" U.

} Settings F

Select "Settings J".

^

Main menu

The display changes into the menu "Settings J".

} Language F

Language

^ Select the menu option you would like to change.

Press the : button to see more information about the
option currently selected.

The selected options in the submenus are marked with a
check L.

r} Sensor Wash

r} Time of day

47

Settings !

Language J

The display contents can be shown in
different languages.

The displayed language can be
changed by the submenu
"Language J".

Select the desired language and

^

confirm with OK.

The flag behind the word
Language J serves as a guide when
an unfamiliar language is selected.
Select the respective menu with a
flag until the submenu Language J
appears.

Time of day

This selection allows the clock to be
shown as 24 or 12 hours. The clock can
also be set from here.

Setting the clock format

Select "Format".

^

Select the desired clock format and

^

confirm with OK.

Set the time of day

Select "Set manually".

^

^ Set the hour with +/- and confirm with

OK. Set the minutes and confirm.

After confirming the minutes with OK,
the display will revert to the previous
menu.

^ Touch "Clear" to get back into the

Settings J menu.

48

Water hardness

Your dishwasher is fitted with a water
softener which you need to program to
the water hardness level in your area,
see "Before the first use".

Turn the dishwasher on K.

^

If the memory function is on, the
program menu instead of the last
selected program will be displayed
(see "Settings - Memory"). If this is the
case use the U button in the main
menu.

Select

^

"Settings

The set water hardness is marked
with a check

^ Select the water hardness of your

local water supply, confirm with

Water hardness from the

!" menu.

(.

OK.

Settings !

°d gr/gal Setting in display

1

2
3
4
5
6
7
8

9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36

37-45
46-60
61-70

1

2
3
4
5
6
7
8

9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
25
26
27
28
29
30
31
32
33
34
35
36
37

38-46
47-62
63-73

1

2
3
4
5
6
7
8

9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
45
60
70

49

Settings !

Rinse aid

For best results the rinse aid dosage
can be adjusted.
The dosage can be set between 0 and
6 ml.

The dosage set by default to 3 ml of
rinse aid per program.

Use a higher setting if spots appear

–

on dry glassware.

Use a lower setting if streaking

–

appears on dishes or glasses.

Selected the desired rinse aid

^

amount and confirm with OK.

Adjust Sensor Wash

The "Sensor Wash" program can be
adjusted to clean stubborn but normal
soiling.

Select Yes and confirm with OK.

^

Drying Plus

To improve the drying process the door
will open (except during the "Extra
Quiet" program) at the end of the
program during the drying phase.

This feature can be turned off.

^ Select the desired setting and

confirm with

If you turn the Drying Plus

,

function off and still want to open the
door at the end of a program, then
open the door completely.
Otherwise steam can damage the
countertop edges, because the fan
will continue to run.

OK.

50

Settings !

Optimize standby

A few minutes after the last key is
pressed or at the end of the program
the dishwasher will switch into Standby
mode to save energy.

This function can also be turned off.
The dishwasher will then turn off
completely after 6 hours.

Select the desired setting and

^

confirm with

If refill salt and/or rinse aid or an fault
are present in the display, the
dishwasher will not turn off.

The refill messages can be turned
off when you use a tab detergent
(see "Settings-Refill display").
Fault messages cannot be turned
off.

OK.

Refill display

When consistently using multi-function
Tab detergents, you can turn off the
refill displays.

Select the desired setting and

^

confirm with

Be sure to turn this setting back on if
you stop using multi-function tab
detergents.

OK.

Check filters

This selection allows you to set the
number of programs run before the
filter check message shows.
You can select between 30 and 60
programs.

The filter check message is set by
default to 50 programs.

^ Select the desired number of

programs and confirm with

OK.

51

Settings !

Reorganize programs

The order of the programs in the program list can be
reorganized. The two most frequently used programs can be
saved to the first two positions.

} Sensor Wash B
} Cancel

Select with e the program which you would like to save to

^

Select program for position Continue }

e

the first position of the main menu. Confirm the selection
with the button next to the program.

Confirm with Continue.

^

^ Repeat with the second program.

The selected programs are displayed as programmed.
To change a program position, select Back until you reach
the respective program position.

^ When you are done reorganizing the program list, confirm

with

Finished.

52

Settings !

Save options

Additional options can be selected for
some programs, e.g. extended drying.
See "Use - Selecting options".

Save options allows you to save the
selected options for future use of the
program.

This function is turned off by default.

Select the desired setting and

^

confirm with OK.

Temperature

The temperature can be displayed in
"°C/Celsius" or "°F/Fahrenheit".

The temperatures are shown in
°C/Celsius by default.

^ Select the desired temperature unit

and confirm with OK.

Buzzer

When the buzzer is activated, a tone
sounds at the end of a program and if a
fault occurs.

The buzzer at the end of a program is
turned on by default.

Buzzer at the end of a program

The buzzer at the end of a program
sounds five times in intervals with a
brief break in between. The buzzer
sounds up to one hour if the
dishwasher in not turned off.

Buzzer in case of a fault

The buzzer for a fault sounds
continuously. The buzzer sounds up to
two minutes if the dishwasher is not
turned off or the fault is fixed.

The buzzer for a fault cannot be set
to off.

Buzzer tone

The buzzer volume can be set to 17
different levels.

The buzzer cannot be turned off in
case of a fault.

^

Select the desired volume.

^

Confirm with

OK.

53

Settings !

Keypad tone

A tone will sound when a button is
pressed.

The volume can be set to 17 different
levels.

Select the desired setting and

^

confirm with OK.

Brightness

The display brightness can be adjusted
in 17 levels.

Select the desired brightness and

^

confirm with OK.

Memory

The memory function allows you to save
the last selected program.

When turning the dishwasher off and on
again after a program has finished or
opening and closing the door, the last
selected program is displayed instead
of the main menu.

RemoteVision

(Optional accessory.
To learn more about RemoteVision
visit www.miele.com.)

Select e to show module state.

^

If "K module connected and ready" is
displayed, no further action is required.

Via the "Options" menu you can:

Reboot the module

–

Reset the factory default settings

–

Enter Ad-Hoc mode

–

Refer to the "RemoteVision" section
of this manual or the RemoteVision
Installation manual for further
instructions.

The function is turned on by default.

^

Select the desired option and confirm
with OK.

54

Settings !

Showroom program

Demo modes are only for
showrooms.

The dishwasher has various demo
programs for showrooms.

The programs "Demo mode" and
"Endless demo mode" show the use
and function range of the dishwasher.

Demo mode:

–

The program is started by pressing
any button. It runs once and must be
started again.

– Endless demo mode:

The program starts as soon as it is
activated and runs in a loop until it is
turned off.

– Demo wash sound:

The program activates the pumps to
demonstrate the wash sound.

– Trade show mode:

Once the machine is used for the
first time this option is disabled in the
display.

–

Drying Plus Demo:
The door opens automatically.

Turning the Showroom program on

Select the desired option, confirm

^

with OK.

Confirm the following messages with

^

OK.

Press any button to start the selected

^

demo mode.

To cancel the demo mode press any

^

button again and confirm with OK.

Turning the Showroom program off

Select Off to deactivate the

^

Showroom program and confirm with
OK.

^ Confirm the message Deactivate

demo mode? with OK.

Factory default

All settings can be reset to factory
default.

^ Confirm the message Reset to factory

default? with OK.

^

Confirm the information All settings
are reset to factory default with OK.

Leaving the "Settings J menu"

^

To leave the "Settings J" touch the
"Clear" U control. The main menu
appears.

55

RemoteVision

Miele's RemoteVision Wi-Fi technology
creates a 'virtual link' between your
appliance and our monitoring center. If
a fault occurs, Miele's client service
center will be notified and contact you,
or another trusted individual identified
on your call roster, in order to gain
access to your appliance to fix the
problem.

For information on set-up and
installation of the RemoteVision module,
see the separate RemoteVision
installation manual.

Be sure your wireless system meets the
following requirements

A wireless router that supports an

–

IEEE 802.11b protocol

Windows XP

–

system, Mac

Cable or DSL modem

–

Microsoft

–

®

or newer operating

®

OS X 10.3 or higher

®

Internet Explorer 6 or

higher, Safari 2.0 or higher, Firefox

1.5 or higher

* Please note that each wireless router

manufacturer supplies their own
device drivers and setup programs.
Due to the differences in
manufacturers, exact router setup
instructions are not included in this
manual. Wording and instructions
may vary.

56

Frequently asked questions

With the aid of the following guide, minor problems can be fixed without a service call.

Repairs should only be carried out by a qualified and trained person in

,

accordance with local and national safety regulations. Unauthorized repairs
could cause personal injury or machine damage.

Technical faults

Problem Possible fault Solution

The program does not
start.

The dishwasher stops
during a program.

The optic indicator is
not visible when a
program has started.

The door is not properly
closed.

The machine is not
plugged in.

The fuse has tripped. Reset the circuit breaker.

The dishwasher is not
turned on.

No program is selected. Select the desired

The fuse has tripped. Reset the circuit breaker.

The reflector was not
properly installed.

Close the door firmly.

Insert the plug.

See data plate for
minimum amperage.

Press g and select a
program.

program.

See data plate for
minimum amperage.

Install the reflector
properly, see the
Installation diagram.

57

Frequently asked questions

Problem Possible fault Solution

The optical interface
flashes fast, the buzzer
sounds or the display
shows the fault:

; Technical fault FXX

Waterproof fault F70

Automatic door closing
fault F32

Automatic door opening
fault F33

There may be a
technical fault.

The waterproof system
has activated.

The door may be
blocked.

Possible technical fault. – Open the door by hand

Before trying to remedy the
fault:

Turn the dishwasher off

–

with the K button.

After a few seconds:

Turn the dishwasher on.

–

Select the desired

–

program.
Close the door.

–
If the problem persists,

contact Technical Service.

Turn off the water supply.

–
Contact Miele Technical

Service.

– Remove the item, if

necessary restart the
program.

If the message shows again
contact Miele Technical
Service.

and restart the program.

If the message shows again
contact Miele Technical
Service.

58

Frequently asked questions

Problems water intake/drain

Problem Possible fault Solution

The optical interface
flashes fast, the buzzer
sounds and the display
shows the fault:

Water intake fault

Fault water intake F12/F13

The water supply is
closed.

Open the water supply all
the way.

Before fixing the fault:

Turn the dishwasher off

–

K.

Fault in the water intake.–Open the water supply all

the way.

– Check and clean the

water intake filter, see
"User Maintenance
Instructions".

– The water pressure at the

water connection is lower
than 4.35 psi. Consult a
plumber.

59

Frequently asked questions

Problem Possible fault Solution

The optical interface
flashes fast.
The program "Energy
Saver" displays the
fault:

Water intake temp. too
low

The optical interface
flashes fast, the
buzzer sounds and the
display shows the
fault:

Drain fault F11

The intake water does
not have a minimum
temperature of 115°F
(45°C). See "Plumbing".

Fault F11:
Fault in the water drain.
There might be water in
the wash cabinet.

Restart the program.

–

If the fault is displayed

–

again, use a different
program.

Before fixing the fault:

Turn the dishwasher off

–

with the K button.

Clean the triple filter.

–

Clean the drain pump and

–

the non-return valve.

See "User Maintenance
Instructions" for more
information on the above.

– Remove any kinks in the

drain hose.

60

Frequently asked questions

General problems with the dishwasher

Problem Possible fault Solution

The display is dark. The dishwasher has

gone into "Standby"
mode to save energy.

The interior lighting is
not turned on when

The interior light was
turned off.

the door is opened.

The optical function
flashes rapidly.
The buzzer sounds.
The display shows the
following fault
message:

Middle spray arm
blocked

The middle or lower
spray arm is blocked by
dishware.

The spray arm jets of
the middle or lower
spray arm are clogged.

or

Lower spray arm blocked

Turn the dishwasher off

–

using the K button.

Turn the interior light on

–

(see "Additional options­BrilliantLight").

Open the dishwasher door

–

and rearrange items
blocking the spray arms.

Turn the dishwasher off K.

–
Then:
– Clean the spray arms. See

"User Maintenance
Instructions".

61

Frequently asked questions

Problem Possible fault Solution

Detergent is left in the
dispenser at the end
of a program.

The detergent lid
cannot be closed
properly.

The door and the
interior walls are still
wet after a program
has finished.

Water remains in the
wash cabinet at the
end of a program.

The dispenser was damp
when detergent was
added.

Detergent residue is
blocking the catch.

This is not a fault! It is the
normal operating mode of
the drying system.

The triple filter in the wash
cabinet is clogged.

The drain pump or the
non-return valve may be
blocked.

The drain hose is kinked. Remove any kinks from the

Dry the dispenser before
adding detergent.

Remove the residue.

The moisture will evaporate
after a short time.

Before fixing the fault:

Turn the dishwasher off

–

K.

Clean the triple filter. See
"User Maintenance
Instructions".

Clean the drain pump and
the non-return valve, see
the "User Maintenance
Instructions".

drain hose.

62

Frequently asked questions

Sounds

Problem Possible fault Solution

There is a knocking
noise in the wash
cabinet

There is a rattling
noise in the wash
cabinet

There is a knocking
noise in the water line

The spray arm is hitting an
item in the basket.

Items are not secure in the
wash cabinet.

A foreign object has
become lodged in the
drain pump.

This may be caused by
the installation or the
diameter of the pipe.

Interrupt the program,
rearrange items blocking
the spray arms.

Interrupt the program, and
rearrange loose pieces.

Remove the foreign object
from the drain pump (see
"Cleaning the drain pump
and non-return valve")

This has no effect on the
dishwasher. If in doubt,
contact a plumber.

63

Frequently asked questions

Poor cleaning results

Problem Possible fault Solution

The dishes are not
clean.

Glasses and cutlery
show streaks. The
glasses take on a
bluish shimmer; the
deposits can be
wiped off.

The dishes were not
loaded correctly.

The program was not
powerful enough.

Stubborn but normal
soiling (e.g. coffee, tea).

Not enough detergent was
dispensed.

The spray arms are
blocked.

The triple filter in the wash
cabinet is clogged or not
correctly inserted.
The spray arm jets might
be clogged as a result.

The non-return valve is
stuck open and blocked.
Wash water will run back
into the wash cabinet.

The rinse aid dosage is
set too high.

See "Loading the
dishwasher".

Select a more intensive
program (see "Program
Guide").

Use the function "Adjust
Sensor Wash" (depending on
model, see "Settings").

Use more detergent, or
change the detergent.

Turn the spray arms and
rearrange the dishes if
necessary.

Clean the filter and insert it
correctly. Clean the spray
arm jets, if required (see
"Cleaning and care").

Clean the drain pump and the
non-return valve (see
"Cleaning and care").

Reduce the dosage (see
"Settings - Rinse aid").

64

Frequently asked questions

Problem Possible fault Solution

Dishes are not dry,
glasses and
cutlery are
spotted.

White residue is
visible on cutlery
and dishes.
Clouding occurs
on glassware and
cutlery; film can be
wiped off.

The rinse aid setting may be
too low, or the rinse aid
reservoir is empty.

Dishes were taken out too
soon.

A "Tab" product was used.
These products have a low
drying effect.

Not enough rinse aid was
used.

The salt container is empty. Refill the salt container (see

The salt container lid was not
screwed on properly.

Unsuitable "Tab" products
were used.

The water softener is
programmed on too low a
setting.

Increase the dosage, refill
the reservoir or switch the
rinse aid product when
refilling (see "Rinse aid").

Leave dishes in longer (see
"Use").

Change the detergent, or
refill the rinse aid (see "Rinse
aid").

Increase the dosage (see
"Setting the rinse aid
dosage").

"Filling the salt container").

Reseat it making sure it
screws back on correctly.

Use a different detergent.
Use normal (powder or gel)
detergent.

Program a higher water
softener setting (see "Water
softener").

65

Frequently asked questions

Problem Possible fault Solution

Glasses have a
brown or blue
discoloration; film
cannot be wiped off.

Glasses are dull and
discolored; film
cannot be wiped off.

Tea or lipstick stains
have not been
completely removed.

Plastics are
discolored.

There are rust stains
on cutlery.

Detergent deposits. Change detergent right

away.

Glasses are not dishwasher
safe. The surface is
affected.

The wash temperature of
the selected program was
too low.

The detergent has a low
bleaching effect.

Natural dyes e.g. from
carrots, tomatoes or
ketchup may be the cause.
Not enough detergent was
used to break down natural
dyes.

The affected items are not
corrosion resistant.

No program was run after
refilling salt. Salt residuals
got in the wash cycle.

The salt container lid was
not screwed on properly.

There is no remedy.
Only use dishwasher safe
glasses.

Select a program with a
higher wash temperature.

Use a different detergent.

Use more detergent (see
"Detergent").
Discoloration is permanent.

There is no remedy.
Use only dishwasher safe
cutlery.

Start the "Express" program
without a load after refilling
salt (without the "Turbo"
option).

Reseat it making sure it
screws back on correctly.

66

After sales service

Repairs

In the event of a fault which you cannot
correct yourself please contact the
Miele Service Department at the phone
number on the back of this booklet.

Please quote the model type and

^

number of your appliance.

These can be found on the data plate
along the right edge of the door.

PC Update

The Program Correction (PC) allows a
technician to update the dishwasher to
make use of new technology.

When, for example, technological
developments offer advanced
modifications to your existing program
cycles a service technician will be able
to input these into your machine
controls via the indicator light marked
PC. Miele will provide information when
such possibilities become available.

MieleCare

(USA only)

MieleCare, our Extended Service
Contract program, gives you the
assurance of knowing that your
appliance investment is covered by
5 years of worry free ownership.
MieleCare is the only Extended Service
Contract in the industry that guarantees
repairs by a Miele Authorized Service
Provider using genuine Miele parts.
Only genuine Miele parts installed by
factory trained professionals can
guarantee the safety, reliability, and
longevity of your Miele appliance.

Please note that unless expressly
approved in writing by Miele’s Service
department, Extended Service
Contracts offered by other providers for
Miele products will not be recognized
by Miele. Our goal is to prevent
unauthorized (and untrained) service
personnel from working on your Miele
products, possibly doing further
damage to them, you and/or your
home.

To learn more about MieleCare
Extended Service Contracts, please
contact your appliance dealer or visit
us online at:

http://mieleusa.com/mielecare

67

68

User Maintenance Instructions

To prevent accidents
and appliance damage,
read these instructions

before

installation or use.

Cleaning and Care

Check and clean your dishwasher
regularly. This will help avoid faults
and problems.

Abrasive cleaning agents,

,

all-purpose cleaners, thinner or
ammonium cleaners should not be
used on the dishwasher.
They will damage the surface.

Exterior

Use a conditioner suitable for your

^

kitchen cabinetry.

Clean wood with a damp cloth and

^

wipe dry.

Clean the exterior with a solution of
warm water and liquid soap applied
with a soft sponge. Dry with a soft
cloth.

Wash cabinet

Generally, the wash cabinet is self
cleaning if the correct amount of
detergent is used.

The wash cabinet can be cleaned with
a dishwasher cleaner such as "Dis
Cleaner" available from your Miele
dealer or online at www.mieleusa.com.

Door and the door seal

^ Wipe the door seals regularly with a

damp cloth to remove food deposits.

^

Food residue and spilled liquids
should be wiped from the sides of the
dishwasher door. These are outside
of the wash cabinet and are not
cleaned by water from the spray
arms.

Glass cleaners may be used to
clean the exterior. However do not
allow them to sit or "puddle", this can
cause damage to the surface.

Remove the cleaner promptly.

To better maintain your appliance
avoid the following:

– cleaners containing soda, ammonia,

thinners, or chlorides

– cleaners containing descaling

agents or lime removers,

–

abrasive cleaners,

–

stainless steel cleaners,

–

dishwasher soap (powder),

–

caustic (oven) cleaners,

–

scouring pads, steel wool, hard
brushes,

–

metal scrapers,

–

steam cleaning products.

70

Indicator reflector

The reflector of the optical interface is
located in the steam deflector beneath
the counter top.

Clean as necessary with a damp

^

cloth.

Control panel

Clean the control panel as necessary

^

with a damp cloth.

The appliance front and controls

,

are not scratch proof.
Remove spills immediately.

Cleaning and Care

71

Cleaning and Care

Triple filter system

The triple filter system in the base of the
wash cabinet prevents food from being
redeposited on dishes. It also protects
the circulation pump from damage
caused by foreign objects (e.g. broken
glass, bones, etc.). During normal use,
the filter system is self-cleaning.

The machine must not be used

,

without all the filters in place!

Check and clean the filter system

^

periodically for any trapped or
foreign objects.

The level of soiling and time it takes
before the filters need cleaning will vary
depending on household.

The display shows Filter check after
50 wash cycles (default setting).

The filter check frequency can be
set from 30 to 60 cycles. See
"Settings J - Filter check".

^

Check and clean the triple filter.

^

Confirm with OK.

Cleaning the triple filter

^ Turn off the dishwasher before

cleaning.

^ Turn the handle counterclockwise to

release the triple filter system, a.

^ Remove the triple filter from the

machine. Clean any solid particles
and rinse under running water. Scrub
with a nylon brush if necessary.

,

Be sure that debris does not get
into the circulation pump causing it
to clog.

The display changes to the program
menu.

72

Cleaning and Care

To clean the underside of the filter the
flap must be opened.

^ Push the clips together a and open

the flap b.

^ Rinse under running water.

^ Close the flap so that the clip

engages.

Return the filter so it lies flat in the

^

base of the wash cabinet.

^ Lock the filter by turning the handle

clockwise.

,The triple filter system must be

inserted and locked. Large particles
could get in the circulation system
and cause blockage.

73

Cleaning and Care

Cleaning the spray arms

Sometimes particles of food get stuck
in the spray arm jets. The spray arms
should be inspected and cleaned every
4 - 6 months.

Turn off the dishwasher before

^

cleaning.

Removing the spray arms

Remove the cutlery tray (if present).

^

Push the upper spray arm up to

^

engage the inner ratchet and
unscrew the spray arm.

Pull the lower spray arm firmly

^

upwards to remove.

^

Lift up the middle spray arm, a,to
engage the ratchet and unscrew the
spray arm, b.

^

Remove the lower basket.

74

^

Use a pointed object such as a
toothpick to push food particles into
the spray arm jets.

^

Rinse thoroughly under running
water.

^

Return the spray arms and check that
they rotate freely.

Cleaning the water inlet filter

A filter is incorporated into the intake
hose attached to the dishwasher’s shut
off valve. If your water is hard or the
pipes contain sediment, this filter may
clog and prevent enough water from
entering the wash cabinet.

The plastic housing of the water

,

connection contains electrical
wiring.
Do not cut the intake hose or
submerge it in liquid.

Installing an in-line water filter

If your water contains a large number of
insoluble substances, a filter between
the water valve and the intake hose
connection is recommended. These
filters can be purchased from Miele.

Cleaning and Care

Carefully remove the rubber seal.

^

^ Remove the filter using needle nose

pliers and rinse it under running
water.

^ Reinsert the filter and seal. Make sure

they are seated correctly.

Cleaning the filter

^ Turn off the dishwasher and pull the

plug.

^

Turn off the water supply.

^

Unscrew the intake hose.

^ Screw the intake hose back on the

water valve, checking that it is not
cross-threaded.

^

Slowly turn on the water supply and
test for leaks.

75

Cleaning and Care

Cleaning the drain pump and
non-return valve

If the dishwasher is not completely
drained at the end of a program, the
drain pump or non-return valve may be
blocked.

Turn off the dishwasher and pull the

^

plug.

Remove the triple filter (see "Triple

^

filter system").

Use a cup or bowl to scoop water out

^

of the wash cabinet.

The drain pump is beneath the
non-return valve (see arrow).

^ Remove all foreign objects from the

drain pump (glass or bone splinters).

^ Before returning the non-return valve,

check that the drain pump is not
blocked. Spin the propeller several
times in both directions to check for
obstructions.

^

Tilt the locking clamp to the side a.

^

Pull out the non-return valve b and
rinse it under running water.

^

Remove all foreign objects from the
non-return valve.

76

^ Carefully reinsert the non-return valve

and secure it with the locking clamp.

,

Make sure the locking clamp
clicks into place!

Installation Instructions

Please refer to the Installation Diagram supplied with these instructions.

To comply with IEC sound testing protocols, please contact Miele for additional
instructions.

Information is subject to change. Please refer to our website to obtain the most
current product specification, technical & warranty information.

Help to protect the environment

Disposal of the packing
material

The cardboard box and packaging
protect the appliance during shipping.
These materials are biodegradable and
recyclable. Please recycle.

Ensure that any plastic wrappings,
bags etc. are disposed of safely and
kept out of the reach of children.
Danger of suffocation!

Disposal of an old machine

Old appliances may contain materials
that can be recycled. Please contact
your local recycling authority about the
possibility of recycling these materials.

Ensure that the appliance presents no
danger to children while being stored
for disposal. Before discarding an old
appliance, unplug it from the outlet, cut
off its power cord and remove any
doors to prevent hazards.

78

Electrical connection

Installation, repairs and other

,

work by unqualified persons could
be dangerous.

Check that the voltage, frequency
and fuse rating shown on the data
plate match the household mains
supply.

The power outlet must be accessible
after installation. Do not use an
extension cord to connect the
dishwasher to the mains. Danger of
overheating! See data plate on the
right side of the door.

A damaged power cord must only
be replaced with a genuine Miele
cord by a Miele service technician.

GROUNDING INSTRUCTIONS

THIS APPLIANCE MUST BE
GROUNDED.

Improper connection of the

,

equipment grounding conductor
can result in electric shock. Do
not modify the plug provided with
the appliance; if it will not fit the
outlet, have a proper outlet
installed by a qualified electrician.
If there is any question
concerning the proper electrical
connection or grounding of this
appliance to the power supply,
please consult a licensed
electrician or call Miele’s
Technical Service Department:

U 1-800-999-1360
V 1-800-565-6435

Specifications

The dishwasher comes equipped with a
4 ft (1.2 m) power cord with a molded
plug for connection to 120 V, 60 Hz,
15 A grounded receptacle.

In the event of a malfunction or
breakdown, grounding will reduce the
risk of electric shock by providing a
path of least resistance for the electrical
current. This appliance is equipped
with a cord having an equipment
grounding conductor and a grounding
plug. The plug must be plugged into an
appropriate outlet that is installed and
grounded in accordance with all local
codes and ordinances.

79

Electrical connection

Hardwired electrical connection

It is possible to hardwire this appliance
to an existing power cable.

CAUTION: Before servicing,

,

disconnect the power supply by
either removing the fuse, shutting off
the power main or manually
"tripping" the circuit breaker.

Prior to making a hardwire

,

connection to the terminal, remove
the power cord. Otherwise there will
be a risk of electric shock from the
attached plug.

An existing flexible supply cord or
cable shall have a minimum thickness
of AWG 14.

Installation work and repairs should
only be performed by a qualified
technician in accordance with all
applicable codes and standards.
Repairs and service by unqualified
persons could be dangerous and
the manufacturer cannot be held
responsible.

Before connecting the appliance to
the power supply, make sure that
the voltage and frequency listed on
the data plate correspond with the
household electrical supply. This
data must correspond to prevent
machine damage. Consult an
electrician if in doubt.

GROUNDING INSTRUCTIONS

THIS APPLIANCE MUST BE
GROUNDED.

This appliance must be connected to a
grounded metal, permanent wiring
system, or an equipment-grounding
conductor must be run with the circuit
conductors and connected to the
equipment-grounding terminal or lead
on the appliance.

120 V, 60 Hz, 15 A fuse rating

Black wire (live): connect to L

White wire (neutral): connect to N
Green wire (ground): connect to -

After attaching the permanent

,

power supply cord, check that all
screws on the terminal block and the
strain relief are tightened.

80

Connection to the water supply

Installation, repairs and other work

,

by unqualified persons could be
dangerous.

Do not drink water from the

,

dishwasher!

The dishwasher can heat its own water

–

to the temperature required by the
wash program. This allows for
connection of the machine to either a
hot (max. 140°F / 60°C) or cold water
source.
For lowest energy consumption and for
fastest possible wash times connect
the dishwasher to a hot water source.
All programs use hot water in the rinse
cycles.

– To use the "Energy Saver" program, a

hot water connection of minimum
115°F / 45°C and maximum 140°F /
60°C (water intake temperature) is
necessary.
The higher the water intake
temperature, the better the cleaning
and drying results.

–

The inlet hose is approximately 5 ft.
(1.5 m) long.

Plumbing

If not connected directly to a water
supply valve, an appropriate
adapter (not included) is required.

Water pressure: Must be between

–

4.5 - 145 psi (0.3 - 10 bar).

If the water pressure if lower, a

–

"Water Intake" notification will be
shown. See "Frequently Asked
Questions" for more information.

If the water pressure is higher than

–

shown, a pressure reducing valve
must be used.

Ensure that the water connection is
secure after the first use.

,

To prevent damage to the
dishwasher, it must only be
connected to a fully vented drainage
system.

,

Do not cut the intake hose. If the
hose is cut, the dishwasher will not
work. There will be a water leak. If
the hose is too long, coil it neatly
and place it behind or under the
machine.

–

The water inlet hose comes
equipped with an inlet hose ending
with a 3/8" female compression
fitting. This can be directly
connected to a water supply valve or
to an appropriate coupling.

81

Plumbing

Drainage

The machine comes equipped with a

–

built-in non-return valve on the
discharge side to prevent waste
water from flowing back into the
dishwasher.

The dishwasher is equipped with a

–

5 ft (1.5 m) flexible drain hose with an
internal diameter of 7/8" (22 mm).

Drain hose extensions and adapters

–

can be ordered from Miele.
The maximum drain hose length is
13 ft. (4 m), max. drain height: 39"
(1 m).

– Use the clamp provided to attach the

hose to the dishwashers P trap or
disposal connection (see the
"Installation Diagram").

The hose must always be attached
on the sink side of the P trap.

The drain hose must not be

–

shortened.

Make sure the hose is not kinked

,

or cut when pushing the machine
under the countertop.

Venting the drainage system

If the dishwasher drain hose is
connected to a floor drain or to a drain
pipe that is less than 8" (20 cm) above
the floor, the drain must be vented.
Otherwise the water inside the
dishwasher may siphon out during the
wash program.

^ Open the dishwasher door and

remove the lower basket.

When attaching the hose to a
garbage disposal fitting, make sure
the plug which is normally blocking
the fitting is knocked out or
removed.

–

The hose can be angled to the left or
right side at the rear of the machine.

–

The existing nipple that the drain
hose is connected to may be
designed for various hose diameters.
If the nipple diameter is to large or to
small it should be replaced or an
adapter may be used. If the nipple
extends more than 2" (50 mm) into
the drain hose it should be
shortened, or the hose could clog.

82

^

Pull the lower spray arm firmly
upwards to remove.

^

Cut off the vent cap located at the
right rear of the triple filter system, as
illustrated.

83

Alteration rights reserved / 1211
G5970/G5975 /

INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST
CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.

M.-Nr. 07 909 280 / 03