Page 1
Fully Integrated
30” Freezer
F 1813 Vi / F 1803 Vi
8mieleusa.com
Page 2
Fully Integrated 30” Freezer
F 1813 Vi / F 1803 Vi
FOR FLUSH INSTALLATION
25" min.*
O
30"
W
84"
24 5/8"
E
10 1/4
83 1/2" - 85 3/8"
29 3/4"
UNIT ACCEPTS
A CUSTOM
FRONT PANEL
Location Codes
5 foot - 120 Volt - 15 Amp 3-wire molded plug power
E -
supply connects lower left rear
Standard NEMA 5-15 Duplex Outlet - locate less than
O -
9" above finished floor
1/4" flexible water line - tape to floor
W -
Notes
• All Installations must be done in accordance with local codes
• Sides of adjoining cabinets should be filled (flush to frame) to
insure proper fit and finish
• For Proud Installation - please adjust accordingly
* Depth assumes a 3/4” panel, please adjust according to
custom panel thickness
1 1/8"
4 1/8"
"8/3 8 - "2
"2/1 8 - "8/5 6
F 1813 Vi / F 1803 Vi
Page 2 of 6
Page 3
Fully Integrated 30” Freezer
appearance
These units do not come equipped with a front panel. They are designed to accept a custom door panel supplied by
the
cabinets
Panel
Panel Notes
If
Simply
F 1813 Vi / F 1803 Vi
CUSTOM PANEL INSTALLATIONS
cabinet maker. Miele has a unique panel integration system which allows the panels to align with the surrounding
.
size is determined in the following manner:
Width: 29 3/4" in all cases
Miele
Fully Integrated
Freezer
Panel Height
Thickness: Minimum 3/4" outside frame
Height: Determined using the following calculation:
Panel Height = HOC - TKH
HOC = Total height of cabinet or side panel
TKH = Toe-kick height
HOC
Note: Finish back side of panels to insure
Panel may extend above unit. This is not
considered in height calculation
Maximum panel weight: 105.8 Pounds
the adjoining cabinets are taller than the height of machine (HOM) - the front panel may be extended accordingly.
maintain the toekick height and extend the panel the needed distance.
Adjoining cabinet
TKH
Extended Panel
Machine
F 1813 Vi / F 1803 Vi
Page 3 of 6
Page 4
Fully Integrated 30” Freezer
rooD °511rooD °09
T
Door
NOTE
s
F 1813 Vi / F 1803 Vi
HINGING DETAILS
Swing
Cabinet Front
1"
1-1/4"
0-1/8"
0-3/4"
F
ro
nt
Pa
n
el
snoitpo ssenkcihTsnoitpo ssenkcih
0-1/8"
0-3/4"
1-1/4"
1-3/4"
1-1/4"
1-1/2"
0-3/4"
1-3/4"
1"
2"
Cabinet Front
0-3/4"
Front Panel
1"
1-1/4"
1-1/2"
1-1/2"
1"
1-1/2"
Door Swing
7/16"
14 3/8"
MAX
32 11/16"
: Additional space needed depending on the thickness
of front panels and handle used.
Freezer units cannot be stop pinned at 90°
NOTE: Additional space needed depending on the thicknes
of front panels and handle used.
Freezer units cannot be stop pinned at 90°
F 1813 Vi / F 1803 Vi
Page 4 of 6
Page 5
Fully Integrated 30” Freezer
0-3/4"
1"
1-1/4"
1-1/2"
0-1/8"
F
ro
nt
Pa
n
el
0-3/4"
1-1/4"
1-1/2"
1-3/4"
1"
Cabinet Front
rooD °511rooD °09
snoitpo ssenkcihTsnoitpo ssenkcihT
Door Swing
16 7/8"
MAX
F 1813 Vi / F 1803 Vi
HINGING DETAILS
3/8”
1
1/6”
1
17/24” (18mm)
1/4”(6.4mm)
5/8”
(67mm)
2
1/3”
2
(59mm)
1/24”
2
(52mm)
(29.6mm)
3/4”
1
(35mm)
3”(76.2mm)
(44.5mm)
F 1813 Vi / F 1803 Vi
Page 5 of 6
Page 6
Fully Integrated 30” Freezer
0-1/8"
Front Panel
1"
1-1/4"
1-1/2"
0-3/4"
0-3/4"
1-1/4"
1-1/2"
1-3/4"
2"
1"
Cabinet Front
0-3/4"
1"
1-1/4"
1-1/2"
F
ro
nt
Pa
n
el
0-3/4"
1-1/4"
1-1/2"
1-3/4"
1"
Cabinet Front
snoitpo ssenkcihTsnoitpo ssenkcihT
F 1813 Vi / F 1803 Vi
HINGING DETAILS FOR INSTALLATION
WITH APPLIANCE/OBJECT ON HINGE
SIDE
7/16”
1
(36.5mm)
11/16”
1
(43mm)
15/16”
1
(49.2mm)
3/16”
1
(30mm)
7/16”
(11 mm)
Handle or object that is
NOT flush with Cabinet
Front.
**When installing hing side next to an appliance or object that is within range of the door panel, limit the
door opening angle to 90O. This is done by installing the banking pin as illustrated. Insert the banking
pin through the holes and drive in with a hammer.
F 1813 Vi / F 1803 Vi
Page 6 of 6
Loading...