Page 1
MasterCool Refrigeration
Side-by-Side Merging Combinations
For SF Models
KSK 1003
Specification Sheets TRS07252017
8mieleusa.com
Page 2
Side-by-Side Merging Kit
KSK 1003
SPECIFICATIONS
KSK 1003 — Item 10562720
Electrical
Power Cord Direct connection to left-standing appliance
Support
Call Miele (800) 999-1360
Miele Website
20/20 Link
This merging kit should be used for side-by-side installation of the following
models:
- K 18x1 SF, K 19x1 SF, K 18x3 SF, K 19x3 SF
- F 14x1 SF, F 18x1 SF, F 19x1 SF, F 14x3 SF, F 18x3 SF, F 19x3 SF
- KF 18x1 SF, KF 19x1 SF, KF 18x3 SF, KF 19x3 SF
- KWT 16x1 SF, KWT 16x3 SF
8www.mieleusa.com
82020technologies.com
For side-by-side installation of appliances with a stainless-steal front (SF),
you also need a Top-frame. Please contact Miele to obtain a top-frame in the
required width. The width of the Top-frame corresponds to the totale width of
you side-by-side combination.
Specification Sheets TRS07252017
Page 2 of 11
Page 3
Side-by-Side Merging Kit
...withpartition
The minimumthicknessofthe partition
is
5
/8"(16 mm).
If thereisapartition withathickness
from
5
/8"(16 mm)to65/16" (160 mm)
betweenthe adjacentappliances, then
each appliance should be individually
installed within itsown niche using the
mountingaccessories included.
en
...withpartition
The minimumthicknessofthe partition
is
5
/8"(16 mm).
KSK 1003
Side-by-side
...without partition
If the appliances are installed directly
next to each other (without a partition),
they need to be attached together. A
heating mat must also be installed. This
will help avoid condensation and
prevent damages.
HEATING MAT TRANSFORMER
PLUG DETAILS FOR KSK 1003
...withpartition
If thereisapartition withathickness
5
less than 6 5/16” (160 mm)
from
/8"(16 mm)to65/16" (160 mm)
betweenthe adjacentappliances, then
each appliance should be individually
installed within itsown niche using the
mountingaccessories included.
In this case, you will only need the heating
mat from the “Merging kit” to avoid
condenstaion and prevent damages.
•
KSK 1003- Heating mat connects directly to left-standing appliance
•
Merging kit must be used when combining units
•
All Installations must be done in accordance with local codes
Specification Sheets TRS07252017
Page 3 of 11
Page 4
Product and Cut-out Dimensions
48” Side-by-Side Combination
FOR PROUD INSTALLATION
E- power cord for refrigeration unit- 5 foot- NEMA 5-15
molded plug power cord connects lower left rear of units
•
Merging kit must be used when combining units
•
KFT1048SS top frame piece must be used when combining
units
•
All Installations must be done in accordance with local codes
Sides of adjoining cabinets should be lled (ush to frame) to
•
insure proper t and nish
Specification Sheets TRS07252017
Page 4 of 11
Page 5
Product and Cut-out Dimensions
48” Side-by-Side Combination
FOR PROUD INSTALLATION
E- power cord for refrigeration unit- 5 foot- NEMA 5-15
molded plug power cord connects lower left rear of units
•
Merging kit must be used when combining units
•
KFT1048SS top frame piece must be used when combining
units
•
All Installations must be done in accordance with local codes
Sides of adjoining cabinets should be lled (ush to frame) to
•
insure proper t and nish
Specification Sheets TRS07252017
Page 5 of 11
Page 6
Product and Cut-out Dimensions
54” Side-by-Side Combination
FOR PROUD INSTALLATION
E- power cord for refrigeration unit- 5 foot- NEMA 5-15
molded plug power cord connects lower left rear of units
•
Merging kit must be used when combining units
•
KFT1054SS top frame piece must be used when combining
units
•
All Installations must be done in accordance with local codes
Sides of adjoining cabinets should be lled (ush to frame) to
•
insure proper t and nish
Specification Sheets TRS07252017
Page 6 of 11
Page 7
Product and Cut-out Dimensions
54” Side-by-Side Combination
FOR PROUD INSTALLATION
E- power cord for refrigeration unit- 5 foot- NEMA 5-15
molded plug power cord connects lower left rear of units
•
Merging kit must be used when combining units
•
KFT1054SS top frame piece must be used when combining
units
•
All Installations must be done in accordance with local codes
Sides of adjoining cabinets should be lled (ush to frame) to
•
insure proper t and nish
Specification Sheets TRS07252017
Page 7 of 11
Page 8
Product and Cut-out Dimensions
60” Side-by-Side Combination
FOR PROUD INSTALLATION
E- power cord for refrigeration unit- 5 foot- NEMA 5-15
molded plug power cord connects lower left rear of units
•
Merging kit must be used when combining units
•
KFT1060SS top frame piece must be used when combining
units
•
All Installations must be done in accordance with local codes
Sides of adjoining cabinets should be lled (ush to frame) to
•
insure proper t and nish
Specification Sheets TRS07252017
Page 8 of 11
Page 9
Product and Cut-out Dimensions
60” Side-by-Side Combination
FOR PROUD INSTALLATION
E- power cord for refrigeration unit- 5 foot- NEMA 5-15
molded plug power cord connects lower left rear of units
•
Merging kit must be used when combining units
•
KFT1060SS top frame piece must be used when combining
units
•
All Installations must be done in accordance with local codes
Sides of adjoining cabinets should be lled (ush to frame) to
•
insure proper t and nish
Specification Sheets TRS07252017
Page 9 of 11
Page 10
Product and Cut-out Dimensions
66” Side-by-Side Combination
FOR PROUD INSTALLATION
E- power cord for refrigeration unit- 5 foot- NEMA 5-15
molded plug power cord connects lower left rear of units
•
Merging kit must be used when combining units
•
KFT1066SS top frame piece must be used when combining
units
•
All Installations must be done in accordance with local codes
Sides of adjoining cabinets should be lled (ush to frame) to
•
insure proper t and nish
Specification Sheets TRS07252017
Page 10 of 11
Page 11
Product and Cut-out Dimensions
72” Side-by-Side Combination
FOR PROUD INSTALLATION
E- power cord for refrigeration unit- 5 foot- NEMA 5-15
molded plug power cord connects lower left rear of units
•
Merging kit must be used when combining units
•
KFT1072SS top frame piece must be used when combining
units
•
All Installations must be done in accordance with local codes
Sides of adjoining cabinets should be lled (ush to frame) to
•
insure proper t and nish
Specification Sheets TRS07252017
Page 11 of 11
Loading...