Midea
Cooker Hood
Instructions
MODEL: MHS60S
60cm Slideout Rangehood
Service Call: 1800 886 010
Read these instructions carefully before using your cooker hood,and keep it
carefully. If you follow the instructions, your cooker hood will provide you with many
SAVE THESE INSTRUCTIONS CAREFULLY
years of good service.
RECOMMENDATIONS AND SUGGESTIONS
The instructions apply to several versions of this appliance. Accordingly, you may nd descriptions of individual
features that do not apply to your appliance.
INSTALLATION
● The manufacturer will not be held liable for any damages resulting from incorrect or
improper installation.
● The minimum safety distance between the cooker top and the extractor hood is 650
mm (some models can be installed at a lower height, please refer to the paragraphs on
working dimensions and installation).
● Check that the mains voltage corresponds to that indicated on the rating plate xed to
the inside of the hood.
● For Class I appliances, check that the domestic power supply guarantees adequate
earthing.
● Connect the extractor to the exhaust ue through a pipe of minimum diameter 120mm.
The route of the ue must be as short as possible.
● Do not connect the extractor hood to exhaust ducts carrying combustion umes (boilers, replaces, etc.).
● If the extractor is used in conjunction with non-electrical appliances (e.g. gas burning appliances),a sufcient
degree of aeration must be guaranteed in the room in order to prevent the backow of exhaust gas. The kitchen
must have an opening communicating directly with the open air in order to guarantee the entry of clean air.
When the cooker hood is used in conjunction with appliances supplied with energy other than electric, the
negative pressure in the room must not exceed 0,04 mbar to prevent fumes being drawn back into the room by
the cooker hood.
● In the event of damage to the power cable, it must be replaced by the manufacturer or by the technical service
department, in order to prevent any risks.
● If the installation instructions for the gas hob specify a greater distance than that specied above, it has to be
taken into account. Regulations concerning the discharge of air have to be fullled.
USE
● The extractor hood has been designed exclusively for domestic use to eliminate
kitchen smells.
● Never use the hood for purposes other than those intended.
● Never leave high naked ames under the hood when it is in operation.
● Adjust the ame intensity to direct the the ame upto the bottom of a pan only,
making sure that it does not engulf the sides.
● Deep fat fryers must be continuously monitored during use: overheated oil can
burst into ames.
● Do not ame under the cooker hood, with a risk of re.
● This appliance can be used by children aged 8 and above and persons with
reduced physical, sensory or mental capabilities or lacking experience and
knowledge if they have been given supervision or instruction concerning use of
the appliance in a safe way and understood the hazards involved.
● Children should be supervised to ensure that they do not play with the appliance.
● Cleaning and maintenance shall not be made by children without supervision.
● “CAUTION: Accessible parts may become hot when used with cooking
appliances”.
MAINTENANCE
● Switch off or unplug the appliance from the mains supply before carrying out
any maintenance work.
● Clean and/or replace the lters after the specied period (re hazard).
● Clean the hood using a damp cloth and a neutral liquid detergent.
● The appliance uses 4 hob elements at most.
The symbol
be handed over to the applicable collection point for recycling of electrical and electronic equipment. By ensuring
this product is disposed of correctly, you will help prevent potential negative consequences for the environment and
human health, which could otherwise be caused by inappropriate waste disposing of this product. For more detailed
information about recycling of this product, please contact your local city ofce, your household waste disposal
service or the shop where you purchased your product.
is a packaging indication that this product may not be treated as household waste. Instead it shall
2
COMPONENTS
Ref. Qty. Product Components
1 1
2 1 Check Valve
3 1 Activated Charcoal Filter
4 1 Screws 5x50
5 1 Wall Plug
Hood Body, complete with Controls, Light,
Blower, Filter.
3
DIMENSION
4
INSTALLATION
METHOD 1
● Refer to the drawings (Method 1)
● Position the hood into the cabinet location and line of the 4 round key holes on top Cooker
Hood. In the cabinet identify the relative position of 4 round key holes.
● Take cane to consider the overall dimensions of the hood including fascia panel using 4 ×screws
supplied install hood securely to cabinet.
Information
When cutting or drilling into wall or ceiling, you should not damage electrical wiring or other
hidden utilities.
METHOD 2
5
METHOD 2
● If the installation surface of the cabinet is not suitable for installing the cooker hood, then as per
gures, x the cooker hood on the correct position of the wall.
● On the wall, install 2 screws (supplied) according to the relative position of 2 key holes at the back
of hood.
● Also install screws in the security holes to provide a safer use in case the hood moves back and
forth.
Information
Congratulations on your purchasing our cooker hood. Before installing and/or using the
cooker hood, carefully read all the instructions.
CONNECTIONS
DUCTED VERSION AIR EXHAUST SYSTEM
When installing the ducted version, connect the hood to the chimney
using either a exible or a rigid pipe of ɸ 150 or ɸ 120 mm, the choice
of which is left to the installer.
● To install a ɸ 120 mm air exhaust connection, insert the reducer
ange 3 on the hood body outlet.
● Fix the pipe 4 in position using sufcient pipe clamps (not supplied).
● Remove possible charcoal lters.
CHECK VALVE INSTALLATION
Hold check valve (black) in your hands and align with the cut out on the top of the Rangehood. Turn
slightly to position check valve in to cut .out.
6
USE
Operation
Check before using
Check the safe condition of the appliance:
● Check whether there are visible defects.
● Check that all parts of the appliance have been securely tted.
Switching on/off
● Control on the right side of cooker hood are the control switches.
● There are 2 speed switches of the motor and on/off switch of the light.
● Locker switch for operation.
Motor Operation
● [ ] = Off
● [ ] = Low Power Setting
● [ ] = High Power Setting
Motor Operation
● [ ] = Off
● [ ] = On
GREASE FILTER
METAL SELF-SUPPORTING GREASE FILTER CLEANING
● The lters must be cleaned every 2 months of operation or more
frequently for particularly heavy usage, and can be washed in a
dishwasher.
● Slide the panel clip to release the aluminum lter.
● Remove the lters one by one by pushing them towards the back
side of the hood unit and simultaneously pulling downwards.
● Any kind of bending of the lters has to be avoided when washing
them. Before tting them again into the hood, make sure that they
are completely dry. (The color of the lter surface may change over
time, but this has no inuence to the lter efciency).
● When tting the lters into the hood, pay attention that they should be mounted in correct
position with the handle facing outwards.
● Close the clip panel.
ACTIVATED CHARCOAL FILTER (RECIRCULATION VERSION)
ACTIVATED CHARCOAL FILTER REPLACEMENT
These lters are not washable and cannot be regenerated, and must be replaced approximately
every 4 months of operation or more frequently for heavy usage.
● Remove the metal grease lters
● Remove the saturated activated charcoal lter.
● Fit the new lters.
● Replace the metal grease lters.
7
Information
When activated charcoal lter is attached, the suction power will be lowered.
Venting knob position
Extraction-air mode: Turning
the venting knob here means
venting outside.
Circulating-air mode: Turning
the venting knob here means
recirculation.
LIGHT
LIGHT REPLACEMENT
● When changing the light bulb, the contacts are live.
● Before changing the light bulb, unplug the appliance from the mains or switch off the circuit
breaker in the fuse box.
1. Remove the grease lter.
2. You can remove the light by rotating it. For the specications of light replacement, refer to the
table below.
Max Power Voltage Picture Light Cap ILCOS D Code
LED Module 3W 220-240V
E14 DBL-3-H-E14-35
8
OLD ELECTRICAL APPLIANCE DISPOSAL
The European Directive 2012/19/EU on Waste Electrical and Electronic Equipment
(WEEE), requires that old household electrical appliances must not be disposed of
in the normal unsorted municipal waste stream. Old appliances must be collected
separately in order to optimize the recovery and recycling of the materials they
contain and reduce the impact on human health and the environment.
The crossed out “Wheeled Bin” symbol on the product reminds you of your
obligation, that when disposing the appliance, you need separately collect them.
Consumers should contact their local authority or retailer for information concerning
the correct disposal of their old appliance.
TROUBLE SHOOTING
Fault Cause Solution
The blade is blocked.
Light is on, but
motor does not
work
Both light and
motor do not work
Oil leakage
Vibration
Insufcient suction
Machine incline
The capacitor is damaged. Replace the capacitor.
The motor is damaged. Replace the motor.
The internal wiring of motor is cut off/
disconnected. An unpleasant smell may
be produced.
Apart from the above mentioned, check the following:
Light is damaged. Replace the light.
Power cord is loose.
Outlet and the air ventilation entrance
are not tightly sealed.
Leakage from the connection of
U-shaped section and cover.
The blade, if damaged, can cause
vibration.
The motor is not tightly fastened. Fasten the motor tightly.
The cooker hood is not tightly xed. Fix the cooker hood tightly.
The distance between the cooker hood
and the cooker top is too large.
Too much ventilation from open doors
or windows.
The xing screw is not tight enough.
The hanging screw is not tight enough
Replace the motor.
Connect the cord as per the electric diagram.
Take down the outlet and seal with
glue.
Take down U-shaped section and
seal with soap or paint.
Replace the blade.
Readjust the distance.
Choose a new place to install the
appliance or close some doors /
windows.
Tighten the xing screw and make
it horizontal.
Tighten the hanging screw and
make it horizontal.
9
To ensure the appliance continues to operate at peak performance, we recommend a routine
service call every 3 years for the life of the appliance.
Maintenance schedule:
FOR SPARE PARTS OR TO FIND THE ADDRESS OF
YOUR NEAREST STATE SPARE PARTS CENTRE IN AUSTRALIA
MIDEA HOME APPLIANCES AUSTRALIA PTY LTD
11/75 Lorimer Street, Docklands, Melbourne, 3008
After-sales service No.: 1800 88 60 10
Loading...