Microsoft E60, E800, TC3100, TC4100, LC2000 User Manual

Microsoft Small Business Server 2000 Installation Guide for HP NetServers E60, E800, LC2000, and HP Server tc3100, and tc4100

NOTICE: The information in this document was last updated for the HP NetServer Navigator CD-ROM version M.04.05. If you don't have the M.04.05 version CD-ROM and you're obtaining this document from the HP web site as a reference to install an operating system, be sure to also check the HP web site for the latest available drivers.

©Copyright Hewlett-Packard Company

January 22, 2002

Introduction

Requirements

Process Flow ( High Level View )

Installation Planning Sheet

Installation Methods

Automatic Installation – Using the HP Navigator CD

Manual Installation

Creating the Drivers Diskettes Selecting the Manual Installation Method

Installing Small Business Server 2000

Hardware Status Check Initialize Hard Drives Configure Server IP Address Attach Clients to Network Domain Controller Setup

Troubleshooting Tips

Tip #1. Upgrading from SBS 4.0 to Small Business Server 2000 Tip #2. Using the Small Business Server 2000 integrated backup utility with the HP NetServer E 60 bundled tape drive

Tip #3. Upgrading Small Business Server 2000 from Uniprocessor HAL to Multiprocessor HAL Tip #4. Small Business Server 2000 Driver Signatures Tip #5. Upgrading D5013B NIC Drivers for Small Business Server 2000 Tip #6. Installation Fails to Boot after First Reboot Tip #7. Small Business Server 2000 Recovery Options Tip #8. Terminal Server Service is only support the NetServer L Series

Frequently Asked Questions

APPENDIX

On-Line Information and Software Sources

Introduction

This document was created by Hewlett-Packard for the purpose of helping you install Microsoft Small Business Server 2000 on your HP NetServer based on procedures tested by HP. The objective of this document is to provide the information needed to achieve the following tasks.

· Install Small Business Server 2000 from Diskette or CD-ROM

· Create boot diskettes from CD-ROM

· Configure system as Domain Controller and DNS Server

· Change IP Address

· Provide installation troubleshooting tips and tricks

Before you start installing or upgrading to Small Business Server 2000 check the following documents and make sure you develop an action plan to complete the installation. Use the following informational resources to help you.

· read1st.txt (Small Business Server 2000 CD-ROM)

· readme.doc (Small Business Server 2000 CD-ROM)

· Troubleshooting Tips and Tricks

at the end of this document.

Requirements

· Microsoft Small Business Server 2000 CD-ROM.

· Target system to be tested with minimum of P166 Processor and 64Meg of RAM (128Meg

Recommended).

· One or more Network Interface Cards (NIC).

· One or more hard drives.

· Latest system BIOS update. (http://www.hp.com)

· Two or more clients for testing purpose. (Optional)

· HP Driver's diskette if installing devices that have no drivers included in the Small Business

Server 2000 CD-ROM. Example: HP NetRAID-4M, HP Fiber Channel adapter (Optional), etc. (This driver's diskette may contain updated Small Business Server 2000 drivers for HP components.)

Process Flow ( High Level View )

1. Locate and install optional components.

2. Install Small Business Server 2000 on NetServer as stand alone system.

3. Hardware status check with "Device Manager" tool.

4. Prepare all logical drives and shared directories.

5. Configure IP address as needed.

6. Attach clients to network.

7. Test network link using the ping utility.

8. Domain controller setup.

9. Create shared directories.

10. Verify that all clients can access the shared directories.

11. Perform a file copy test.

Installation Planning Sheet

Complete the following table before you begin the installation process. You will need this information in order to answer questions that you will be asked during the installation process.

Partition Table: ______________________(List target partitions)

User Name: _________________________

Organization: ________________________

Licensing: ___________________________

Computer Name: ______________________

Admin Password: _____________________

Date Time Zone: ______________________

Workgroup or Domain Name: ______________

Registration Key: ____________________________

Installation Methods

There are several ways of installing Small Business Server 2000. The most popular methods are listed below. Select a method and go to the appropriate section of this guide to begin. Depending upon your system and its configuration, it may also be necessary to create a drivers diskette.

1. Automatic Installation – boot from the HP Navigator CD and run the Configuration/Installation utility. (Supported on all HP NetServer systems.)

2. Manual Installation – do the following:

· Create the HP NetServer Small Business Server 2000 drivers diskettes using the HP NetServer Navigator CD-ROM.

· Select one of the following methods for installation:

- Create Small Business Server 2000 Setup diskettes. Use those diskettes to begin the installation. Insert and use the Small Business Server 2000 CD when prompted.

- Boot directly from the Small Business Server 2000 CD to begin the installation.

Automatic Installation – Using the HP Navigator CD

HP recommends that you follow this method to install Small Business Server 2000. This is the easiest method because it requires less user intervention. Following are the steps to complete the installation of Small Business Server 2000 using the HP Navigator CD.

1. Boot the system from the HP Navigator CD.

2. From the "NetServer Navigator Select a NOS" screen, select the operating system that you will be installing. Then, select "Continue".

3. At the main menu, select "Configure the Server".

4. Then select "Guided Setup" and follow the instructions on the screen.

Manual Installation

Creating the Drivers Diskette

Before you begin, use one of the following two methods that can be used to create the drivers diskette. One method is to create the drivers diskette using a system booted from the Navigator CD. The other method is to create the drivers diskette using a system that is running Windows NT, Small Business Server 2000, or Windows 95/98.

Creating the Drivers Diskette at the server after booting from the Navigator CD

1. Boot the system from the Navigator CD.

2. From the "NetServer Navigator Select a NOS" screen, select the operating system that you will be installing. Then, select "Continue".

3. From the "Diskette Title" window, select the diskette that you want to create and then select "Create Diskette(s)". Follow the on-screen instructions to create the desired diskette(s).

Create the Drivers Diskette using a system running Windows NT, Small Business Server 2000, or Windows 95/98

1. Insert the Navigator CD in the CD-ROM drive on the Windows-based system.

NOTE: The system's monitor must be set for at least 800 x 600 resolution.

2. Your system should auto-detect the presence of the CD and start the Navigator process. If your system does not auto-start the Navigator process, start it by executing LAUNCH32.EXE which can be found at the root level of the Navigator CD.

3. Once the Navigator process has started, select the target HP NetServer system from the dropdown menu and select "Continue".

4. From the "NetServer Navigator Select a NOS" screen, select the operating system that you will be installing. Then, select "Continue".

5. At the "NetServer Navigator Main Menu" screen, select "Diskette Library".

6. From the "Diskette Title" window, select the diskette that you want to create and then select "Create Diskette(s)". Follow the on-screen instructions to create the desired diskette(s).

Selecting the Manual Installation Method

Before using this method of installation, decide whether you want to install Small Business Server 2000 using Setup Diskettes, or by booting directly from the Small Business Server 2000 CD.

· If you wish to create Setup Diskettes (perhaps because you have other systems that do not support booting from CD), proceed to the following section "Creating Setup Diskettes."

· If you want to start the setup by booting directly off the Small Business Server 2000 CD (supported for all NetServers), proceed to the following section "Installing Small Business Server 2000."

Creating Setup Diskettes

If you opt for starting the Small Business Server 2000 installation from Setup Diskettes, do the following:

1. You need four blank, formatted diskettes. Label them as listed below:

Small Business Server 2000 Setup Boot. Small Business Server 2000 Setup Disk #2. Small Business Server 2000 Setup Disk #3. Small Business Server 2000 Setup Disk#4

2. Place the Small Business Server 2000 CD on a system running Windows NT or Windows 95 or 98.

3. Open a command prompt and change to the d:\bootdisk directory (assuming that D: is your CD-ROM drive).

4. At the command prompt type:

makebt a: (If using a DOS or a Windows 95 or 98 system) makebt32 a: (If using an NT system)

5. Follow the on-screen instructions provided by the utility.

Starting the Installation Small Business Server 2000 Using Setup Diskettes

1. Boot from the "Small Business Server 2000 Setup Boot" diskette. Follow instructions displayed, replacing diskettes as necessary.

2. When prompted for the Small Business Server 2000 CD-ROM, place the CD in the drive and then proceed to Step 2 in the next section "Installing Small Business Server 2000" to continue the installation.

Installing Small Business Server 2000

1. If you have opted not to use Setup Diskettes, place the Small Business Server 2000 CD in the CD-ROM drive. Power off and on to reboot the system. You will see a message that reads "Setup is inspecting your hardware configuration.". Then the setup screen will be displayed.

NOTE: If you experience any hang or issue during this time, consult the Tips/Tricks section of this document for help.

2. If you have new drivers to add then press F6 to add OEM SCSI, DAC. Read the message that shows at the bottom of the display indicating when to press F6.

NOTE: If the boot device driver is not included on the Small Business Server 2000 CDROM, for example the "HP NetRAID-4M", then do the following steps after pressing F6

a) Press S to select additional hardware. b) Select Other and press Enter. c) When prompted to insert driver diskette, please insert the target adapter driver's diskette created with the HP Navigator CD-ROM. Press Enter to continue. d) Select the target device driver from the list provided on the display. For example, if you have the "HP NetRAID-4M", select "Hewlett Packard NetRAID-4M RAID CONTROLLER". e) If you have no other drivers that you need to install, press Enter to continue with the installation.

3. Press Enter to continue at the "Small Business Server 2000 Server Setup. Setup Notification…" screen.

4. Press Enter to continue at the "Small Business Server 2000 Server Setup. Welcome to Setup…" screen.

5. Press C to continue Setup at the "Setup has determined that your computer's startup hard disk is new…" prompt.

6. Press F8 to accept the licensing agreement.

7. At the drives partitioning screen, select the target drive. If you want to use the entire drive to install Small Business Server 2000 then press Enter. Otherwise, press C to create a drive a partition. (In this example we will create a 2GB partition. Please note that Small Business Server 2000 does not have the 2GB partition size limitation present on NT 4.0.)

8. Type 2048 and press Enter at the Create partition size prompt.

9. HP recommends that you create all the partitions needed for each hard drive present on your system at this time.

10. Select the target drive to be used to install Small Business Server 2000. Press Enter.

11. Select Format the partition using the NTFS file system and press Enter.

12. The installer will format and copy files to the hard drive. The system will then reboot.

13. Click Next to continue at the Setup Wizard first dialog box.

14. The Installing Devices screen will be shown with a progress bar on the display. This may take 10 to 15 minutes.

+ 15 hidden pages

Microsoft E60, E800, TC3100, TC4100, LC2000 User Manual

Table of Contents

Introduction

Requirements

Process Flow ( High Level View )

Installation Planning Sheet

Installation Methods

Manual Installation

Creating the Drivers Diskette

Selecting the Manual Installation Method

Installing Small Business Server 2000