MGE UPS Systems 66102, 66103 User Manual

www.mgeops.com

Network Management Card (66102 & 66103)

User manual

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 1/120

Contents

1.1

1.1.1 Connecting the UPS to the Ethernet network 6

1.1.2 Protection of the computers/servers 6

1.1.3 Supervision of the UPSs over the network 7

1.1.4 Connection 7

1.2

1.2.1 Compatibility with UPSs 8

1.2.2 Direct sending of E-mail 9

1.2.3 Sending text messages (SMS) 9

1.2.4 Compatibility with the Network Management Systems (NMS) – Trap sending 9

1.2.5 Environment Sensor (option) 9

1.3

1.3.1 Hardware characteristics 10

1.3.2 EMC Compatibility 10

1.3.3 Configuration 10

1.3.4 Administration 11

1.3.5 Network 11

1.3.6 Environment sensor 11

1.3.7 MIB (Management Information Base) 12

1.3.8 Default parameters 13

MGE OFFICE PROTECTION SYSTEMS NETWORK SOLUTION 5

ENERAL PRESENTATION

RESENTATION OF THE NETWORK MANAGEMENT CARD

ECHNICAL DATA

(NMC) 8

2.1

2.2

2.3

2.4 3

3.1

3.1.1 Your network is equipped with a DHCP server 18

3.1.2 Your network is not equipped with a DHCP server 19

3.2 4

4.1

4.2

4.2.1 UPS properties page 21

4.2.2 On-line help 33

4.2.3 UPS control 34

4.2.4 UPS weekly schedule programming 37

4.2.5 Shutdown parameters 38

4.2.6 Measurements 40

4.2.7 Event log 41

4.2.8 System log 42

4.3

ENERGIZE YOUR ENTERPRISE Network Management Card

INSTALLATION 14

NPACKING AND CHECK ON CONTENTS

NDICATIONS

NSTALLATION IN THE

ENSOR INSTALLATION (OPTION

CONFIGURATION 17

ONFIGURE IP PARAMETERS

EST AFTER CONFIGURATION

SUPERVISION AND ADMINISTRATION BY BROWSER 20

PTIMISING THE PERFORMANCE OF YOUR BROWSER

UPS 21

OTIFICATION

UPS 15

– User Manual 34003991EN/DA Page 2/120

) 16

4.3.1 Email Notification 43

4.3.2 E-mail Message Settings 45

4.4

4.4.1 Network settings 48

4.4.2 System 50

4.4.3 Notified Applications 52

4.4.4 Central shutdown configuration 54

4.4.5 Access control 55

4.4.6 Date and time 57

4.4.7 Firmware upload 59

4.5

4.5.1 Characteristics 60

4.5.2 Environment Status 61

4.5.3 Environment Settings 62

4.5.4 Log 64

ONFIGURATION

NVIRONMENT SENSOR (OPTION

) 60

5.1

5.1.1 Shutdown criteria managed by the Network Management Card 65

5.1.2 Controlled outlets 68

5.1.3 Protection of a server connected to a controlled outlet 68

5.2

5.2.1 Extended power outage, shutdown initiated by the Shutdown Timer (Shutdown after) 69

5.2.2 Extended power outage, shutdown initiated by the "Low battery power" message 69

5.2.3 Case of power restoration before the end of the "shutdown duration" counter 70

5.3

5.3.1 Shutdown Duration 71

5.3.2 Settings 71

6.1

6.2

6.2.1 Choice 1: Read Network settings 73

6.2.2 Choice 2: Modify Network settings 74

6.2.3 Choice 3: Set Ethernet speed 74

6.3

6.4

SERVER PROTECTION 65

SET-

UP OF THE SHUTDOWN PARAMETERS

HE DIFFERENT SERVER AND

HUTDOWN MANAGEMENT WITH 2

CONFIGURATION VIA RS232 72

HOICE 1: RESTART / RESET

HOICE 2: NETWORK CONFIGURATION

HOICE 3: LOST PASSWORD / SET LOGIN PASSWORD TO DEFAULT

HOICE 4: RETURN TO DEFAULT CONFIGURATION

UPS

SHUTDOWN SEQUENCES

NMC

BOARDS

7.1

7.1.1 Overview 77

7.1.2 Functions 77

7.1.3 Technical characteristics 78

7.2

7.2.1 RS232 link configuration and connection 79

7.2.2 RS485 link configuration and connection 80

7.2.3 Configuration of the JBUS/MODBUS communication parameters 86

7.3

ENERGIZE YOUR ENTERPRISE Network Management Card

INDUSTRIAL NETWORK MANAGEMENT CARD (INMC OPTION) 77

RESENTATION

NSTALLATION

DDITIONAL WEB PAGES

– User Manual 34003991EN/DA Page 3/120

7.4

7.4.1 Data for Pulsar 700 / 1000 / 1500 91

7.4.2 Data for Pulsar M 2200 / 3000 93

7.4.3 Data for Pulsar MX 4000 / 5000 / 10000 95

7.4.4 Data for Pulsar MX frame 15 / 20 97

7.4.5 Sensor data 102

7.4.6 Other data 105

8.1

8.1.1 Table of alarms 106

8.1.2 Table of UPS events 109

8.1.3 Table of system alarms 111

8.2

8.2.1 MGE MIB 112

8.2.2 Table des TRAPS : (1.3.6.1.4.1.705.1.11) 115

JBUS

TABLE

APPENDICES 106

ABLES OF ALARMS AND EVENTS

SNMP

OBJECTS

112

106

GLOSSARY 117

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 4/120

1 MGE Office Protection Systems Network Solution

1.1 General Presentation

MGE Office Protection Systems Network Solution: provides information on events concerning the supply of power to the computers connected to your computer

network, carries out automatic shutdown of computer systems, monitors and controls all the UPSs connected to the network.

As illustrated in the picture below, MGE Office Protection Systems Network Solution provides these 3 main functions: supervision of the UPSs over the Network, protection of the computers, connexion of the UPS to the Network.

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 5/120

1.1.1 Connecting the UPS to the Ethernet network

This function can be performed either through network Cards inserted in the UPS (Network Management Card) or through a software "agent" running on a nearby PC that is called the Network Management Proxy.

The Network Management Card or Proxy:

- manages communication with the UPS (as well as local protection of the machine on which Proxy is installed)

- periodically accesses the information concerning the UPS

- makes this information available to the connected applications (Network Shutdown Modules, Web Browser, Network Management Systems, Enterprise Power Manager)

- sends notifications on certain events.

Operation may be in standard secure mode (the default mode) or in SSL secure mode (Secure Socket Layer SSL).

1.1.2 Protection of the computers/servers

This function is performed by the Network Shutdown Module installed on each of the servers to be protected. Note that the Shutdown Module is available on several Operating Systems.

The Network Shutdown Module:

Continuously waits for information from the Network Management Card/Proxy connected to the MGE Office Protection Systems. Warns administrators and users if AC power fails and proceeds with graceful system shutdown before the end of battery backup power is reached.

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 6/120

1.1.3 Supervision of the UPSs over the network

Depending on your needs, you can either use:

Your Internet browser to monitor each UPS, as Management Proxy and Management Card includes a Web server Your company’s standard Network Management System (HP-Openview, CA Unicenter, HP Insight Manager, IBM Tivoli Netview) To simplify integration of MGE Office Protection Systems UPSs, you can use one of the Network Management System Kits for MGE devices. These kits are available on the Management Pac 2 CD-ROM. (ref 66923) The MGE supervisor "Enterprise Power Manager".

1.1.4 Connection

Before installing the MGE Office Protection Systems Network Solution, the UPS must be set up as indicated in the steps below. Shut down the computers to be protected by the UPS. Connect the UPS to a wall outlet. (For UPSs above 3kVA, please refer to the UPS installation manual). Connect the power cord of each computer to an outlet on the UPS. (For UPSs above 3kVA, please refer to the UPS installation manual)

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 7/120

1.1.4.1 How to connect UPS / agent / network:

Insert the optional card in the UPS and connect the UPS to the computer network. Start the MGE Office Protection Systems UPS, then the computers.

1.1.4.2 Setting up the protection:

Set up the Network Management Card (see user manual). Install and configure the Network Shutdown Module on all machines that are to be protected by the UPS.

The software components for each platform and the user manuals are on the Solution-Pac-2 CD or are available for download on the www.mgeops.com Web site, in the “Downloads” section.

1.2 Presentation of the Network Management Card (NMC)

1.2.1 Compatibility with UPSs

The Minislot Network Management Card is compatible with the following UPSs: Pulsar Evolution 500/800/1100 From technical level 06 Pulsar Evolution 2200/3000 From technical level 05 Pulsar Evolution 1500 From technical level 05 EXtreme C 700/1000/1500 From technical level B2 EXtreme C 2200 - 3200 From technical level 02 Pulsar EX 700/1000/1500 RT (US°) From technical level 03 Pulsar EX 2200/3200 (US°) From technical level 09 Pulsar M 2200/3000 All models Pulsar 700/1000/1500 All models Evolution 650/850/1150/1550/2000 All models Evolution S 1250/1750/2500/3000 All models Pulsar MX 4/5/10 All models Pulsar MX 15/20 All models EX 5 / 7 / 11 RT Equipped with a card minislot (Q2 08) EX 5 / 7 / 11 RT 3 : 1 Equipped with a card minislot (Q2 08)

Note: If the UPS's NT is below that indicated in the table above, contact MGE's Office Protection Systems technical support. The Network Management Card (66102) is not compatible with Pulsar EX 7/10, Pulsar EX 15/20/30, Pulsar ESV+, 8/11/14/22 ranges.

Network Management Cards acquire information on the operation status of the UPS systems and provide remote control of these systems by means of an ETHERNET network from any SNMP administration station or Web browser. They also supply alarms to the Network Shutdown Modules to trigger shutdown or other automatic actions for protected servers.

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 8/120

Network Management Cards are compatible with the "Enterprise Power Management" supervision system and with the MGE Office Protection Systems network protection system.

Network Shutdown Module

Entreprise Power Manager

Management-Pac 2

1.2.2 Direct sending of E-mail

When a UPS event occurs, the Network Management Card can directly notify up to 4 intranet or extranet addresses

by e-mail. (see E-mail Notification and E-mail message settings)

1.2.3 Sending text messages (SMS)

The card offers the possibility of redirecting UPS alarms to an e-mail server. The format of these e-mails is compatible with mobile telephone e-mail/SMS transfer systems proposed by ISPs. The format to be used depends on the service provider. For example, sms.0660256585@votre-login.activmail.net (text messages).

1.2.4 Compatibility with the Network Management Systems (NMS) – Trap

sending

The Network Management Cards are compatible with the major Network Management Systems (IBM Tivoli, CA

Unicenter, HP Insight Manager). The Management-Pac 2 offering includes the necessary SNMP plug-ins to allow an

easy integration in the NMS. Events are notified by SNMP trap.

NMS can subscribe on page “Notified Applications”

The trap list is given in the appendix.

1.2.5 Environment Sensor (option)

The Environment Sensor (66846) solution comprises a box to be connected to the Card Settings port of the

Network Management Cards.

Environment Sensor enables measurement of temperature and humidity around the UPS, consideration of external

alarms via 2 dry contacts and notification of alarms according to pre-programmed thresholds. (see Environmen

Status and Environment Configuration)

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 9/120

1.3 Technical data

1.3.1 Hardware characteristics

Dimensions

Dimensions (L x l x H) 132 x 66 x 42 mm

Weight (gr) 70 g Storage

Storage temperature -10 °C to 70 °C Ambient conditions

Operating temperature 0 °C to 40 °C

Ambient humidity 90 % RH max without condensation

ROHS 100 % compatible

1.3.2 EMC Compatibility

When correctly installed and used in accordance with the manufacturer's instructions, the Network Management Card

complies with the following standards: Safety for ATI: IEC/EN 60950-1 2002 EMC: EN 61000-6-2 (2002), EN 61000-6-3 (2002). IEC/EN 62040-2 (2002).

As per European directives:

Low voltage: 73/23/EEC and 93/68/EEC EMC: 89/336/EEC and 93/68/EEC.

1.3.3 Configuration

The user can configure the card with one of the following means: Web browser Local serial link (network parameters) BOOTP/DHCP (network parameters).

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 10/120

1.3.4 Administration

Up to 50 workstations protected by Network Shutdown Modules - Central or local configuration. Up to 5 browsers connected at the same time (3 in SSL).

◗ Minimum recommended browser versions: Internet Explorer 6.x / 7.0, Mozilla Firefox 1.5 / 2.0

E-mail sending configurable according to UPS alarms and transmission of a periodical report. Control of UPS on/off switching via the HTML interface. Adjustment and control of PowerShare outlets via the HTML interface, sequential starting of the installation and optimisation of backup time by shutting down non-priority systems. Automatic data and time adjustment via NTP server. Protection by encrypted password. Protection by secure SSL connection. Saving of logs in the non-volatile memory. Languages available: English/French/Spanish/German/Italian. On-line help in English available for each page. Card firmware updated via the network.

1.3.5 Network

◗ Fast ETHERNET 10/100 Mbits compatibility with auto-negotiation on the RJ45 outlet.

1.3.5.1 List of ports used

◗ BootP, DHCP UDP 68, 67 ◗ HTML TCP 80 ◗ SSL TCP 443 ◗ NSM in connected mode TCP 5000 ◗ SMTP 25 ◗ NTP 123 ◗ SNMP V1 161 ◗ TRAP SNMP 162

1.3.6 Environment sensor

◗ Temperature measurement from 0 to 70 °C with +/- 1 °C accuracy. ◗ Measurement of humidity from 0 to 100 % with +/- 6 % accuracy. ◗ Min / max time-stamped function for temperature and humidity. ◗ Choice of temperature readings in Celsius or Fahrenheit. ◗ High and low thresholds, hysteresis and offset adjustable via Web interface. ◗ Possibility of notification of status changes by e-mail, SMS or SNMP trap. ◗ Position detection of 2 dry contacts (maximum sensor/contact distance: 20 m). ◗ Name and status of each configurable contact.

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 11/120

◗ Recording of events and measurements in the card log ◗ Possibility of shutting down the installation in the event of a threshold being exceeded or on opening / closure of a

dry contact

◗ Connection to the card with straight CAT5 RJ45 network cables (maximum card/sensor distance: 20 m) ◗ Hot installation

1.3.7 MIB (Management Information Base)

◗ Compatible with MIB MGE Office Protection Systems V1.7

The list of objects managed can be found in the appendix

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 12/120

1.3.8 Default parameters

Function Parameter Default value Possible value

Network IP address 172.17.16.16 Network IP address

Subnet mask 255.255.0.0 Network IP address Gateway Address 0.0.0.0 Network IP address BOOTP/DHCP Enabled Active / Deactivated Firmware Upload Enabled Active / Deactivated SMTP server smtpserver 49 characters maximum

System UPS Contact Computer Room Manager 49 characters maximum

UPS Location Computer Room 31 characters maximum History log interval (sec.) 60 10 to 99999 sec. Environment log interval (sec.) 300 10 to 99999 sec. Default Language English English / French / Spanish /

German / Italian

Manager table empty 50 maximum Access control User name MGEUPS 10 characters maximum

Password MGEUPS 10 characters maximum Community name read public 49 characters maximum Trap port 161 Non configurable

Date and time Date and time adjustment Accept automatic update from

NSM or EPM

NTP server ntpserver 49 characters maximum Serial link Speed 9600 baud Non configurable Data bits 8 Non configurable Stop bits 1 Non configurable Parity without Non configurable Flow control without Non configurable

Synchronise with an NTP

server

Accept automatic update from

NSM or EPM

Synchronise manually

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 13/120

MAC addre

2 Installation

2.1 Unpacking and check on contents

The installation kit contents:

◗ A Network Management Card (66102) ◗ A serial communication cable for configuration (34003918) ◗ Installation manual (34003905)

2.2 Indications

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 14/120

Ethernet port

LED Colour Activity Description

ACT Green

100M Orange

Service port

◗ Off ◗ Card not connected to the network.

◗ On

◗ Flashing

◗ Off ◗ Port operating at 10Mbits/s. ◗ On ◗ Port operating at 100Mbits/s.

◗ Card connected to the network but

without activity

◗ Port is active in receiving /

transmission

LED Colour Activity Description

UPS Green

Data

RS232 Orange

◗ Off ◗ Card startup in progress.

◗ On

◗ Flashing

◗ Off ◗ Configuration menu is active ◗ On ◗ Normal operation. Configuration

◗ Flashing ◗ Communication with the

◗ Communication with UPS in

progress

◗ Normal operation.

Communication with the UPS is operational

menu is deactived

Environment Sensor (option).

2.3 Installation in the UPS

The Network Management Card (66102) can be "hot" installed in all UPSs of the MGE Office Protection Systems range equipped with a Minislot without having to shut it down.

◗ Remove the protective plastic cover from the Minislot ◗ Note the card's MAC address prior to insertion ◗ Insert and tighten the card's retaining screws ◗ Connect the ETHERNET cable ◗ Wait 2 min. the card is completely operational when the green UPS Data LED flashes continuously

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 15/120

2.4 Sensor installation (option)

The Environment sensor is available as an option on the Network Management Card and is available from MGE Office Protection Systems (reference 66846). The sensor allows remote monitoring of the UPS's environment through regular measurements: temperature, humidity, status of two external contacts. It also enables notification of alarms (e-mail, trap SNMP) according to pre-programmed thresholds. It is connected to the Service port (Settings/Sensor) directly on the Network Management Card with a standard Ethernet cable (20 meters maximum). Recognition is automatic. Supervision and configuration are performed via a menu that can be accessed directly from the home page.

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 16/120

3 Configuration

3.1 Configure IP parameters

Once the card has started: Connect one end of the cable (34003918) to the Service port. If the environment sensor was previously connected, the card must be restarted in order to access the configuration menu. Connect the other end of the cable to the COM port (IOIOI) of a PC. Launch a HyperTerminal™ type emulator with the following configuration: Speed: 9600 Data bits: 8 Parity: none Stop bits: 1 Flow control: none "Locally reproduce the characters entered" option: deactivated.

Enter MGEUPS or mgeups. The main menu is displayed:

----------------------------------------------------------------------------MGE UPS SYSTEMS NETWORK MANAGEMENT CARD

---------------------------------------------------------------------------- 1 : Reset 2 : Network configuration 3 : Set Login Password to Default 4 : Return to Default Configuration 0 : Exit

-----------------------------------------------------------------------------

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 17/120

3.1.1 Your network is equipped with a DHCP server

The card is configured by default with this service activated. The card automatically collects IP parameters. To know the IP parameters, type 2, the next menu is displayed:

----------------------------------------------------------------------------Network settings

---------------------------------------------------------------------------- 1 : Read Network settings 2 : Modify Network settings 3 : Set Ethernet speed 0 : Exit

-----------------------------------------------------------------------------

Then type 1. The menu is displayed:

Network configuration : MAC address : 00:06:23:00:1F:8F Mode : Static IP IP address : 172.17.21.94 Subnet mask : 255.255.248.0 Gateway : 172.17.17.1

Note the IP address. To exit, enter 0 then 0. The card is operational. Note: As long as the card is not connected to the network, it continuously attempts to make connection. Once the connection has been established, the operational mode presented in the table above becomes effective.

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 18/120

3.1.2 Your network is not equipped with a DHCP server

In the main menu enter 2, then 2 again. The menu is displayed: Follow the instructions and enter the static IP parameters. At the end of the menu, wait for the "Done" message to be displayed indicating that the IP parameters have been saved.

----------------------------------------------------------------------------Network settings

---------------------------------------------------------------------------- 1 : Read Network settings 2 : Modify Network settings 3 : Set Ethernet speed 0 : Exit

----------------------------------------------------------------------------For each of the following questions, you can press <Return> to select the value shown in braces, or you can enter a new value. Should this target obtain IP settings from the network?[N] N Static IP address [172.17.21.94]? 172.17.21.21 Static IP address is 172.17.21.21 Subnet Mask IP address [255.255.248.0]? 255.255.255.0 Subnet Mask IP address is 255.255.255.0 Gateway address IP address [172.17.17.1]? 172.17.17.1 Gateway address IP address is 172.17.17.1 Wait during your new configuration is saved ... Reset the card to take into account the new configuration.

Return to the main menu and enter 1 then 2. The card restarts with the new IP parameters.

3.2 Test after configuration

To check that the Network Management Card is operational after installation and configuration. From a station connected to the same subnet as the card, open a web browser and enter the IP address of the card in the address field Check the display of the home page.

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 19/120

4 Supervision and administration by browser

◗ On a computer equipped with a Web browser (Internet Explorer, FireFox or Netscape recommended), enter the

address initialised previously in the Installation chapter (e.g. http://172.17.16.16.) The "UPS properties" home page is displayed.

4.1 Optimising the performance of your browser

◗ To view status changes on the UPS in real time, the browser must be configured so that it automatically refreshes

all the objects on the current page. Example on IE 6: Tools / Internet Options / General / Parameters menu, tick Every time this page is visited and validate.

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 20/120

4.2 UPS

4.2.1 UPS properties page

This page is automatically refreshed every 10 seconds.

From this page, access to the main UPS information is available thanks to the combo box (see screen copy below). The different choices are the following ones: “UPS Status”: (chosen by default) this page gives instant access to the essential information about your UPS. “UPS Alarms”: to view the list of current alarms. “UPS Modules”: (available on modular UPS) to view general information on each modules. “About your UPS”: provides information on the UPS and the card, in particular, the model range and software version.

These different pages are detailed in the following chapters.

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 21/120

4.2.1.1 "UPS" zone: general information on the UPS.

Indication of the picture and generic name of the UPS range Computer room: Customised name of your system. You can change this name on the "System" page.

UPS status icon : The various icons showing the status of the UPS are:

Normal operation

Alarm present. This icon links directly to the

Animated synoptic: An animated synoptic gives a global overview of the UPS current operating mode. This synoptic is available on On-Line and Line-interactive UPS. The synoptic drawing depends on the UPS topology. The different drawings are described in the table below.

alarm page. Loss of communication with the UPS

UPS with automatic bypass

UPS with automatic and manual bypass

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 22/120

UPS without automatic bypass

Note: In case of loss of communication with the UPS, all the elements of the synoptic are grey.

The various elements of the synoptic are the following ones:

◗ AC Normal Input :

◗ AC Normal Flow :

◗ AC to DC Converter:

In tolerances

Out of tolerances

AC to DC converter powered by AC Normal AC to DC converter not powered by AC Normal

Powered

Not powered

Internal failure

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 23/120

◗ Battery :

◗ Battery Output Flow :

◗ DC to AC Converter Input flow :

◗ DC to AC Converter :

Remaining capacity > 50%

Remaining capacity < 50%

Battery to be checked (battery test result)

DC to AC converter powered by battery DC to AC converter not powered by battery

Energy flow present No energy flow

Powered

◗ DC to AC Converter Output :

◗ AC Bypass Input :

Not powered

Internal failure

Energy flow present No energy flow

In tolerances

Out of tolerances

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 24/120

◗ AC Automatic Bypass Flow :

◗ AC Automatic Bypass Status :

Energy flow present No energy flow

Powered

Not powered

Internal failure

◗ AC Manual Bypass Flow :

◗ AC Manual Bypass Status :

◗ AC Output Flow :

◗ AC Output :

Energy flow present No energy flow

Open

Closed

Energy flow present No energy flow

Load protected

Load not protected

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 25/120

◗ UPS measurements : ◗ Boxes showing measurements appear when synoptic elements are hovered by the pointer. See example below.

These measurements are available for AC to DC converter, Battery, DC to AC converter and automatic bypass. The measurements available in these boxes depend on the UPS range.

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 26/120

4.2.1.2 "UPS status" zone: Essential information

◗ "Active sources": (available on parallel or modular UPS)

x UPS + y UPS redundant : x indicates the minimal number of UPS necessary to power the load, y indicates the number of UPS in redundancy. An alarm can be generated if the number of UPS in redundancy is less than a configurable threshold. See UPS modules section.

◗ "Power source": indicates whether the power comes from the utility or from the UPS battery ◗ "Output load level": indicates the power percentage used at UPS output ◗ "Output": indicates if the different UPS outputs are protected. ◗ "Master": indicates if the UPS main output is protected ◗ "Group1 and Group2": indicates if the controlled outlets (if available) are powered.

The various icons showing the status of the UPS outputs are:

(green outlet) (red outlet)

Battery Information :

◗ "Battery load level": remaining battery charge (in percent).

The information is completed with the two following labels:

◗ “Charging” : if the utility power is present and the battery charge is in progress ◗ “Discharging”: if the UPS operates on battery. ◗ “Fault”: if the battery is faulty. ◗ "Remaining backup time": Estimation of the battery's maximum backup time remaining before UPS shutdown ◗ "Battery status": Result of the last automatic battery test carried out by the UPS

Possible values are: – OK: the test was completed correctly – NOK: the battery needs to be checked – Deactivated: the automatic battery test is not validated on the UPS

Outlet powered Outlet not powered or not

protected

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 27/120

4.2.1.3 Viewing the modules

◗ Click on "UPS Modules" scroll list to view the information about the UPS modules.

◗ Active sources:

x UPS + y UPS redundant : x indicates the minimal number of UPS necessary to power the load, y indicates the number of UPS in redundancy. The addition of these 2 values is the total number of available UPS.

◗ The "Minimum redundant UPS modules to trigger alarm can be configured from this page. The button Save makes

the card setting the parameter into the UPS. A warning message informs the user about the consequences of this parameters modification. The redundancy lost can generate Email notification (if set in the email notification page) and SNMP trap. It can also be used by NSM for server protection criteria.

◗ The Module Nr gives the location of the module in the UPS.

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 28/120

◗ The Status can take the next forms:

or when the module is working properly with no alarm.

when the module has at least one alarm (level Warning) active.

when the module has at least one alarm (level Critical) active.

when the module has a communication fault.

When the module is working properly with no alarms, the icon is not reactive, otherwise it is reactive and clicking on it makes the page Alarm Table appear.

◗ "Output load level": Value of the percentage of load at module output

◗ "Battery load level": Percentage of charge available in the battery module

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 29/120

4.2.1.4 Viewing the alarms

Click on "Alarm Table" scroll list to view the list of current alarms. The table of managed alarms is included in the

appendix.

The level of the alarms appears like below:

Critical Warning Unknown

◗ Alarm table for standard UPS

ENERGIZE YOUR ENTERPRISE Network Management Card

– User Manual 34003991EN/DA Page 30/120

+ 90 hidden pages

MGE UPS Systems 66102, 66103 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual