Mercedes-Benz Nokia 3109c, Nokia 3110c Installation Manual
Accessories
Installation Instructions
Mobile telephone cradle
Nokia 3109c and 3110c
© 2009, Daimler AG
01/09
03F094-08
1
M+P-03F-7076
1
Validity
These installation instructions are valid for
vehicles equipped with a
• Mobile phone fitting with interface
(Code 386) or
• Mercedes-Benz mobile phone (code 388)
- Each in combination with Nokia mobile
phone 3109c or 3110c.
Components
• (1) Mobile phone cradle
In the following text, this will be referred to
as "cradle".
Notes
Please contact a qualified specialist workshop if you encounter difficulties when fitting the telephone module. Mercedes-Benz
recommends that you use a Mercedes-Benz
Service Centre for this purpose.
The manufacturer reserves the right to
change technical details from those shown
in the illustrations contained in these instal
-
lation instructions.
These installation instructions also refer to
the COMAND and Audio Operating Instruc
tions, the vehicle Owner's Manual and the
mobile phone operating instructions. Please
keep them handy for reference.
At high outside temperatures, the cradle can
become very hot when in operation, as is the
case with the vehicle interior itself.
Do not open up the cradle and do not make
any modifications on the cradle. Otherwise
the type approval will be rendered invalid.
The installation and operation is described
for the Nokia mobile phone 6300.
Installation and operation of the Nokia
mobile phones 3109c and 3110c are done in
the same manner.
2
Contents
Fitting the holder 컄 4
Inserting the mobile phone 컄 5
Setting up the vehicle profile 컄 6
Pairing the mobile phone with
the cradle
컄 7
Connecting the mobile phone
to the cradle
컄 9
• Connecting the mobile
phone manually
컄 10
• Connecting the mobile
phone automatically
컄 10
Switching to hands-free mode 컄 11
General notes on operation 컄 12
Speed-dial keys 컄 13
Removing the mobile phone 컄 14
Removing the cradle 컄 14
3
GRisk of accident
Please comply with the legal regulations of the country in which you are
driving when you are using the tele
-
phone inside the vehicle.
If it is legally permissible to use the
telephone while driving, only do so
when traffic conditions allow for it.
You may otherwise become distrac
ted from the traffic, which may lead
to an accident in which you or
others may be injured.
For safety reasons, only use the
hands-free system when making
calls while driving.
When you are using the mobile phone via the hands-free system, drive
with extra caution, close all windows
and try to eliminate background
noise.
Please pull over or park the car if
you do not wish to use the handsfree system to make a call. Do not
stop the vehicle or park where it is
prohibited to do so.
Place the telephone module into the
cradle only while the vehicle is at a
standstill.
You could otherwise be
distracted and cause an accident.
4
Fitting the holder
1. Slide the cradle (1) onto the contact
plate
(2) until it audibly engages.
2
1
M+P-03F-5601
5
Inserting the mobile phone
It is only possible to use the hands-free
system and the telephone functions via the
operating system/on-board computer when
the mobile phone is in the cradle and a
Bluetooth® connection is established.
1. Insert the mobile phone (3) into the
cradle
(1) as shown.
1
3
M+P-03F-7077
6
Setting up the vehicle profile
It is recommended to set up your own profile
for the hands-free mode, to which the mobile
phone automatically changes when the pho
ne is inserted in the cradle. (Please refer to
the mobile phone operating instructions.)
The ring tone and ring tone volume can be
adapted to the vehicle in the hands-free
mode profile.
Note
If you do set up a profile for the hands-free
mode and have activated the "Silent" profile,
there will be no audible ring tone even when
the phone is inserted in the cradle.
If you have activated the "Flight" profile, no
connection will be established between the
cradle and the inserted mobile phone.
(Please refer to the mobile phone operating
instructions.)
1. Insert the mobile phone in the cradle.
Note
You can take the mobile phone out of the
cradle to set up the profile for the hands-free
mode.
2. Setting up a profile: On the mobile phone in "Menu" "Settings" "Accessories"
"Handsfree" "Default profile" set,
for example, "My style 1".
3. Setting the ring tone volume: Set the
ring tone volume on the mobile phone in
"Menu" "Settings" "Profile" "My pro
file 1" "Change" "Ring tone volume".
7
Pairing the mobile phone with the cradle
For pairing, the mobile phone must not be in
the cradle, but it must be in the vehicle.
1. Turn the ignition key to position 1, 2 or 3.
(Please refer to the vehicle Owner's Manual.)
2. Select "Menu" "Settings" "Con-
nections" "Bluetooth" "ON" on the
mobile phone. (Please refer to the mobile
phone operating instructions.)
3. Press the Bluetooth® button (6) for approximately 2 seconds. The LED (7) flashes
rapidly. The cradle is visible to searching
devices for approx. 2 minutes and can be
detected by the mobile phone.
4. Select "Menu" "Settings" "Con-
nections" "Bluetooth" "Search for audio
devices" on the mobile phone. (Please refer
to the mobile phone operating instructions.)
The mobile phone begins searching for the
cradle. When the mobile phone finds the
cradle, "MB N3110Cradle" appears in the
mobile phone display.
6
7
M+P-03F-7079
8
Note
When you receive the request: "Make phone
visible to all devices?" it is recommended to
reject the request with "No". (Please refer to
the mobile phone operating instructions.)
5. Select "MB N3110Cradle" on the mobile
phone and confirm with "Yes". After confir
mation, a passkey request appears on the
display.
6. Enter passkey 62872 on the mobile
phone.
7. Confirm the request "Allow automatic
establishing of a connection via the device?"
with "Yes" in order to make an automatic
connection between the mobile phone and
the cradle possible.
Note
If the selected device name already exists in
the mobile phone memory, then it is neces
sary to rename the cradle in order to save
the cradle in the mobile phone memory.
(Please refer to the mobile phone operating
instructions.)
As soon as the passkey is entered and
accepted, the mobile phone shows the message "Paired with MB N3110Cradle". The
connection between the mobile phone and
the cradle is automatically interrupted if the
mobile phone was not inserted in the cradle
during pairing.
8. The mobile phone is now ready to be
used with the hands-free system.
Note
A maximum of 4 mobile phones may be
paired with the cradle. If a fifth mobile phone
is paired with the mobile phone cradle, the
mobile phone that was paired first is dele
-
ted.
9
Connecting the mobile phone to the cradle
After the pairing, the connection between
the mobile phone and the cradle is establis
hed automatically as soon as the mobile
phone is inserted in the cradle. The LED on
the cradle lights up continuously.
In order for the hands-free system to function properly, the phone which is in the
cradle may not be connected with the Bluetooth® interface of COMAND or the Audio
System. Please refer to the separate Opera
ting Instructions of COMAND or the Audio
System.
Insert the mobile phone in the cradle and
turn the ignition key to position 1, 2 or 3.
(Please refer to the vehicle Owner's Manual.)
Notes
Only the mobile phone which is inserted in
the cradle is connected to the cradle.
In order to use the hands-free system, the
mobile phone must be inserted in the cradle.
If the mobile phone cradle and the mobile
phone are not connected automatically, the
connection can be established manually
(
컄 10).
The mobile phone battery is charged when
the ignition key is in position 1, 2 or 3.
Not every ring tone can be issued by
COMAND or the vehicle's operating system/
on-board computer.
While there is a connection between the
mobile phone and the cradle, the name of
the mobile service provider is displayed in
the operating system/on-board computer,
as long as there is sufficient reception.
10
Manually connecting the mobile phone
with the cradle
1. Insert the mobile phone in the cradle.
2. Push the Bluetooth® button on the cradle.
Or:
For S-Class vehicles, W/V 221, and CL-Class
vehicles, C 216:
• Select "Tel" "Tel" Telephone"
using the COMAND controller. (Please
refer to the vehicle Owner's Manual.)
On some model series
•Press the button. (Refer to the
COMAND or Audio Operating Instructions.)
Note
Before being manually connected, the mobile
phone must be paired with the cradle (
컄 7).
Automatically connecting the mobile
phone with the cradle
1. Select "Menu" "Settings" "Con-
nections" "Bluetooth" "Paired devices"
on the mobile phone. (Please refer to the
mobile phone operating instructions.)
2. Select "MB N3110Cradle" on the mobile
phone.
3. Select "Options" "Auth. Conn. w/o
Conf." on the mobile phone and confirm with
"Yes". (Please refer to the mobile phone ope
-
rating instructions.)
Loading...