V oltage on any Pin Relativ e to VSSVCC-0.5V to 7.0V
Ambient Operating TemperatureT opr0°C to 70°C
Storage T emperatureTstg-65°C to 125°C
Note: minimum DC v oltage on input or I/O pins is -0.5V. During voltage transitions, inputs may undershoot VSS to -2.0V
for periods of up to 20ns. Maximum DC voltage on input or I/
O pins is VCC+0.5V. During voltage transitions, input may
overshoot VCC to VCC+2.0V for periods of up to 20ns.
Output
Buffer
D0
D15/(D7)
P/N:PM0138
REV. 4.5, JUL. 16, 2001
2
MX23C8100
DC CHARACTERISTICS (Ta = 0°C ~ 70°C, VCC = 5V±10%)
ItemSymbolMIN.MAX.Conditions
Output High VoltageVOH2.4V-IOH = -1.0mA
Output Low VoltageVOL-0.4VIOL = 2.1mA
Input High VoltageVIH2.2VVCC+0.3V
Input Low VoltageVIL-0.3V0.8V
Input Leakage CurrentILI-10uA0V, VCC
Output Leakage CurrentILO-10uA0V , VCC
Operating CurrentICC1-60mAtRC=100ns, all output open
Standby Current (TTL)ISTB1-1mACE=VIH
Standby Current (CMOS)ISTB2-50uACE> VCC - 0.2V
Input CapacitanceCIN-10pFTa = 25°C, f = 1MHZ
Output CapacitanceCOUT-10pFTa = 25°C, f = 1MHZ
AC CHARACTERISTICS (Ta = 0°C ~ 70°C, VCC = 5V±10%)
ItemSymbol 23C8100-10 23C8100-12 23C8100-15
MIN.MAX.MIN.MAX.MIN.MAX.
Read Cycle TimetR C100ns-120ns-150nsAddress Access TimetAA-100ns-120ns-150ns
Chip Enable Access TimetACE-100ns-120ns-150ns
Output Enable TimetOE-50ns-60ns-70ns
Output Hold After AddresstOH0ns-0ns-0nsOutput High Z DelaytHZ-20ns-20ns-20ns
Note:Output high-impedance delay (tHZ) is measured from
OE or CE going high, and this parameter guaranteed by design over the full voltage and temperature operating range not tested.
P/N:PM0138
REV. 4.5, JUL. 16, 2001
3
AC T est Conditions
Input Pulse Levels0.4V~2.4V
Input Rise and Fall Times10ns
Input Timing Level1.5V
Output Timing Le v el0.8V and 2.0V
Output LoadSee Figure
TIMING DIAGRAM
RANDOM READ
MX23C8100
IOH (load)=-1mA
DOUT
IOL (load)=2.1mA
Note:
No output loading is present in tester load board.
Active loading is used and under software programming control.
Output loading capacitance includes load board's and all stray capacitance.
C<100pF
ADD
CE
OE
DATA
ADDADDADD
tAA
tRC
tOH
tACE
tOE
VALIDVALIDVALID
tHZ
P/N:PM0138
REV. 4.5, JUL. 16, 2001
4
PACKAGE INFORMATION
42-PIN PLASTIC DIP(600 mil)
MX23C8100
P/N:PM0138
REV. 4.5, JUL. 16, 2001
5
44-PIN PLASTIC SOP
MX23C8100
P/N:PM0138
REV. 4.5, JUL. 16, 2001
6
48-PIN PLASTIC TSOP
MX23C8100
P/N:PM0138
REV. 4.5, JUL. 16, 2001
7
MX23C8100
REVISION HISTORY
RevisionDescriptionPag eDate
4.2DC Characteristics: The standby current (CMOS) ISTB2 isSEP/01/1997
changed as 50us instead of 100uA.
AC Characteristics: Deleted 200ns gr ade item.
The output enable time (tOE) is changed as 60ns instead of 70ns
in 120ns grade item, and 70ns instead of 80ns in 150ns grade item.
The output high Z delay is changed as 20ns instead of 70ns.