Mazda CX 3 2019 Owner's Manual
A Word to Mazda Owners
Thank you for choosing a Mazda. We at Mazda design and build vehicles with complete
customer satisfaction in mind.
To help ensure enjoyable and trouble-free operation of your Mazda, read this manual
carefully and follow its recommendations.
An Authorized Mazda Dealer knows your vehicle best. So when maintenance or service is
necessary, that's the place to go.
Our nationwide network of Mazda professionals is dedicated to providing you with the best
possible service.
We assure you that all of us at Mazda have an ongoing interest in your motoring pleasure
and in your full satisfaction with your Mazda product.
Mazda Motor Corporation
HIROSHIMA, JAPAN
Important Notes About This Manual
Keep this manual in the glove compartment as a handy reference for the safe and enjoyable use of your Mazda.
Should you resell the vehicle, leave this manual with it for the next owner.
All specifications and descriptions are accurate at the time of printing. Because improvement is a constant goal
at Mazda, we reserve the right to make changes in specifications at any time without notice and without obligation.
Air Conditioner and the Environment
Your Mazda's genuine air conditioner is filled with a refrigerant that has been found not to damage the earth's
ozone layer. If the air conditioner does not operate properly, consult an Authorized Mazda Dealer.
Perchlorate
Certain components of this vehicle such as [air bag modules, seat belt pretensioners, lithium batteries,…] may
contain Perchlorate Material-- Special handling may apply for service or vehicle end of life disposal. See
www.dtsc.ca.gov/hazardouswaste/perchlorate.
Please be aware that this manual applies to all models, equipment and options. As a result, you may find
some explanations for equipment not installed on your vehicle.
©2018 Mazda Motor Corporation
February 2018 (Print1)
How to Use This Manual
We want to help you get the most driving
pleasure from your vehicle. Your owner's
manual, when read from cover to cover,
can do that in many ways.
Illustrations complement the words of the
manual to best explain how to enjoy your
Mazda. By reading your manual, you can
find out about the features, important
safety information, and driving under
various road conditions.
The symbol below in this manual means
“Do not do this” or “Do not let this
happen”.
Index: A good place to start is the Index,
an alphabetical listing of all information in
your manual.
You'll find several WARNINGs,
CAUTIONs, and NOTEs in the manual.
NOTE
A NOTE provides in formation and
sometimes suggests how to make better
use of your vehicle.
The following symbol, located on some
parts of the vehicle, indicates that this
manual contains information related to the
part.
Please refer to the manual for a detailed
explanation.
WARNING
A WARNING indicates a situation in which
serious injury or death could result if the
warning is ignored.
CAUTION
A CAUTION indicates a situation in which
bodily injury or damage to your vehicle, or
both, could result if the caution is ignored.
Table of Contents
Pictorial Index
Interior, exterior views and part identification of your Mazda.
Essential Safety Equipment
Important information about safety equipment, including seats, seat belt
system, child-restraint systems and SRS air bags.
Before Driving
Use of various features, including keys, doors, mirrors and windows.
When Driving
Information concerning safe driving and stopping.
Interior Features
Use of various features for ride comfort, including air-conditioning and
audio system.
Maintenance and Care
How to keep your Mazda in top condition.
If Trouble Arises
Helpful information on what to do if a problem arises with the vehicle.
1
2
3
4
5
6
7
Customer Information and Reporting Safety Defects
Important consumer information including warranties and add-on
equipment.
Specifications
Technical information about your Mazda.
Index
8
9
10
1
Pictorial Index
Interior, exterior views and part identification of your Mazda.
Interior Overview..............................1-2
Interior Equipment (View A)........1-2
Interior Equipment (View B)........1-3
Interior Equipment (View C)........1-4
Interior Equipment (View D)........1-5
Exterior Overview.............................1-6
1-1
Pictorial Index
Interior Overview
Interior Equipment (View A)
① Door-lock knob..................................................................................................... page 3-18
② Turn and lane-change signal..................................................................................page 4-48
③ Lighting control.....................................................................................................page 4-43
④ Wiper and washer lever.........................................................................................page 4-49
⑤ TCS OFF switch....................................................................................................page 4-69
⑥ Lane Departure Warning System (LDWS) switch................................................page 4-87
⑦ Smart City Brake Support (SCBS) OFF switch......................................page 4-121, 4-126
⑧ Blind Spot Monitoring (BSM) OFF switch.......................................................... page 4-95
⑨ Outside mirror switch............................................................................................page 3-31
⑩ Door-lock switch...................................................................................................page 3-16
⑪ Power window lock switch................................................................................... page 3-34
⑫ Power window switches........................................................................................page 3-34
1-2
The equipment and installation position varies by vehicle
Interior Overview
Interior Equipment (View B)
Pictorial Index
① Audio control switches..........................................................................................page 5-16
② Instrument cluster..................................................................................................page 4-11
③ Dashboard illumination knob................................................................................page 4-17
④ Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function)
switches............................................................................................................... page 4-110
⑤ Cruise control switches...................................................................................... page 4-140
⑥ Seat warmer switches..............................................................................................page 2-6
⑦ Heated steering wheel switch................................................................................page 3-29
⑧ Hazard warning flasher switch..............................................................................page 4-55
⑨ Push button start......................................................................................................page 4-4
⑩ Steering shift switches...........................................................................................page 4-36
⑪ Lock release lever................................................................................................. page 3-29
⑫ Hood release handle.............................................................................................. page 6-19
⑬ Remote fuel-filler lid release.................................................................................page 3-27
The equipment and installation position varies by vehicle
1-3
Pictorial Index
Interior Overview
Interior Equipment (View C)
① SRS air bags.......................................................................................................... page 2-45
② Active driving display........................................................................................... page 4-21
③ Climate control system............................................................................................page 5-4
④ Rear window defogger switch...............................................................................page 4-53
⑤ Audio system............................................................................................... page 5-20, 5-64
⑥ Accessory socket................................................................................................ page 5-128
⑦ External input terminal..........................................................................................page 5-17
⑧ Shift lever/Selector lever............................................................................. page 4-30, 4-32
⑨ Commander switch................................................................................................page 5-64
⑩ Electric parking brake (EPB) switch.....................................................................page 4-57
⑪ AUTOHOLD switch............................................................................................. page 4-63
⑫ Drive selection switch........................................................................................... page 4-73
⑬ Fuse block (Left side)............................................................................................page 6-48
1-4
The equipment and installation position varies by vehicle
Interior Overview
Interior Equipment (View D)
Pictorial Index
① Seat belts............................................................................................................... page 2-15
② SRS air bag............................................................................................................page 2-45
③ Bottle holders......................................................................................................page 5-131
④ Sunvisor.............................................................................................................. page 5-126
⑤ Vanity mirror...................................................................................................... page 5-126
⑥ Overhead lights...................................................................................................page 5-126
⑦ Moonroof switch................................................................................................... page 3-36
⑧ Rearview mirror.................................................................................................... page 3-32
⑨ Glove compartment............................................................................................ page 5-132
⑩ Cup holders.........................................................................................................page 5-129
⑪ Center console.................................................................................................... page 5-132
⑫ Front seat.................................................................................................................page 2-5
⑬ Armrest..................................................................................................................page 2-11
⑭ Rear seat..................................................................................................................page 2-9
The equipment and installation position varies by vehicle
1-5
Pictorial Index
Exterior Overview
① Hood......................................................................................................................page 6-19
② Windshield wiper blades....................................................................................... page 6-29
③ Moonroof...............................................................................................................page 3-36
④ Door and key......................................................................................................... page 3-11
⑤ Fuel-filler lid......................................................................................................... page 3-27
⑥ Wheels and Tires...................................................................................................page 6-36
⑦ Exterior lights........................................................................................................page 6-41
⑧ Rear window wiper blade......................................................................................page 6-30
⑨ Liftgate.................................................................................................................. page 3-21
⑩ Child safety lock................................................................................................... page 3-19
⑪ Outside mirror....................................................................................................... page 3-31
1-6
The equipment and installation position varies by vehicle
2
Essential Safety Equipment
Important information about safety equipment, including seats, seat
belt system, child-restraint systems and SRS air bags.
Seats....................................................2-2
Seat Precautions............................2-2
Front Seat......................................2-5
Rear Seat.......................................2-9
Head Restraints...........................2-12
Seat Belt Systems.............................2-15
Seat Belt Precautions..................2-15
Seat Belt......................................2-18
Seat Belt Warning Systems.........2-19
Front Seat Belt Pretensioner and
Load Limiting Systems...............2-19
Seat Belt Extender......................2-21
Child Restraint................................ 2-23
Child-Restraint Precautions........2-23
Child-Restraint System
Installation..................................2-28
Child-Restraint System Suitability
for Various Seat Positions
Table........................................... 2-30
Installing Child-Restraint
Systems.......................................2-33
SRS Air Bags....................................2-45
Supplemental Restraint System
(SRS) Precautions.......................2-45
Supplemental Restraint System
Components................................2-52
How the SRS Air Bags Work..... 2-54
SRS Air Bag Deployment
Criteria........................................2-58
Limitations to SRS Air Bag........2-59
Front Passenger Occupant
Classification System
Constant Monitoring...................2-65
*
................2-61
*Some models.
2-1
Essential Safety Equipment
Seats
Seat Precautions
WARNING
Make sure the adjustable components of a seat are locked in place:
Adjustable seats and seatbacks that are not securely locked are dangerous. In a sudden stop
or collision, the seat or seatback could move, causing injury. Make sure the adjustable
components of the seat are locked in place by attempting to slide the seat forward and
backward and rocking the seatback.
Never allow children to adjust a seat:
Allowing children to adjust a seat is dangerous as it could result in serious injury if a child's
hands or feet become caught in the seat.
Do not drive with the seatback unlocked:
All of the seatbacks play an important role in your protection in a vehicle. Leaving the
seatback unlocked is dangerous as it can allow passengers to be ejected or thrown around
and baggage to strike occupants in a sudden stop or collision, resulting in severe injury. After
adjusting the seatback at any time, even when there are no other passengers, rock the
seatback to make sure it is locked in place.
Adjust a seat only when the vehicle is stopped:
If the seat is adjusted while the vehicle is being driven, the seating posture may become
unstable and the seat could move unexpectedly resulting in injury.
Do not modify or replace the front seats:
Modifying or replacing the front seats such as replacing the upholstery or loosening any bolts
is dangerous. The front seats contain air bag components essential to the supplemental
restraint system. Such modications could damage the supplemental restraint system and
result in serious injury. Consult an Authorized Mazda Dealer if there is any need to remove or
reinstall the front seats.
Do not drive with damaged front seats:
Driving with damaged front seats, such as seat cushions torn or damaged down to the
urethane, is dangerous. A collision, even one not strong enough to
damage the front seats which contain essential air bag components. If there was a
subsequent collision, an air bag may not deploy which could lead to injuries. Always have an
Authorized Mazda Dealer inspect the front seats, front seat belt pretensioners and air bags
after a collision.
the air bags, could
inate
2-2
Essential Safety Equipment
Seats
Do not drive with either front seats reclined:
Sitting in a reclined position while the vehicle is moving is dangerous because you do not get
the full protection from seat belts. During sudden braking or a collision, you can slide under
the lap belt and suer serious internal injuries. For maximum protection, sit well back and
upright.
Do not place an object such as a cushion between the seatback and your back:
Putting an object such as a cushion between the seatback and your back is dangerous
because you will be unable to maintain a safe driving posture and the seat belt cannot
function at its full capacity in a collision, which could result in a serious accident, injury or
death.
Do not place objects under the seat:
The object could get stuck and cause the seat to not be xed securely, and result in an
accident.
Do not stack cargo higher than the seatbacks:
Stacking luggage or other cargo higher than the seatbacks is dangerous. During sudden
braking or a collision, objects can y around and become projectiles that may hit and injure
passengers.
Make sure luggage and cargo is secured before driving:
Not securing cargo while driving is dangerous as it could move or be crushed during sudden
braking or a collision and cause injury.
Never allow a passenger to sit or stand on the folded seatback while the vehicle is moving:
Driving with a passenger on the folded seatback is dangerous. Allowing a child to sit up on
the folded seatback while the vehicle is moving is particularly dangerous. In a sudden stop or
even a minor collision, a child not in a proper seat or child-restraint system and seat belt could
be thrown forward, back or even out of the vehicle resulting in serious injuries or death. The
child in the baggage area could be thrown into other occupants and cause serious injury.
CAUTION
When operating a seat, be careful not to put your hands or ngers near the moving parts of
the seat or on the side trim to prevent injury.
When moving the seats, make sure there is no cargo in the surrounding area. If the cargo
gets caught it could damage the cargo.
2-3
Essential Safety Equipment
Seats
(Manual Seat)
When moving the seats forward and rearward or returning a rear-reclined seatback to its
upright position, make sure you hold onto the seatback with your hand while operating. If
the seatback is not held, the seat will move suddenly and could cause injury.
NOTE
•
When returning a rear seat to its original position, place the seat belt in its normal
position. Verify that the seat belt pulls out and re tr ac ts.
•
(Power Seat)
The seat-bottom power adjustment is operated by moto rs . Avoid extended operation
because excessive use can damage the motors.
•
To prevent the battery from runnin g do wn, avoid using the power adjustment when the
engine is stopped. The adjuster uses a large amount of electrical power.
•
Do not use the switch to make more than one adjustment at a time.
•
When getting in and out of the vehicle, your foot could accidentally co nta ct the se at height
adjustment lever and cause the seat to lower.
Adjust the seat to obtain the correct driving position.
2-4
Seat Operation
▼
Power operation
Essential Safety Equipment
Seats
Front Seat
Seat Slide
(Manual Seat)
To move a seat forward or backward, raise the lever and slide the seat to the desired position
and release the lever.
Make sure the lever returns to its original position and the seat is locked in place by
attempting to push it forward and backward.
(Power Seat)
To slide the seat, move the slide lifter switch on the outside of the seat to the front or back
and hold it. Release the switch at the desired position.
Height Adjustment
(Manual Seat)
To adjust the seat height, move the lever up or down.
(Power Seat)
To adjust the seat height, move the switch up or down.
Height Adjustment for Front Edge of Seat Bottom (Driver's Power Seat)
To adjust the front height of the seat bottom, raise or lower the front of the slide lifter
switch.
*
*Some models.
2-5
Essential Safety Equipment
Seats
Seat Recline
(Manual Seat)
To change the seatback angle, lean forward slightly while raising the lever. Then lean back
to the desired position and release the lever.
Make sure the lever returns to its original position and the seatback is locked in place by
attempting to push it forward and backward.
(Power Seat)
To change the seatback angle, press the front or rear side of the reclining switch. Release the
switch at the desired position.
Lumbar Support Adjustment (Driver's Power Seat)
To increase the seat firmness, press and hold the front part of the switch to the desired
position, then release it.
Press the rear part of the switch to decrease firmness.
Seat Warmer
▼
*
The front seats are electrically heated. The
ignition must be switched ON.
Press the seat warmer switch while the
ignition is switched ON to operate the seat
warmer. The indicator lights turn on to
indicate that the seat warmer is operating.
The mode changes as follows each time
the seat warmer switch is pressed.
OFF
High
Mid
Low
WARNING
Be careful when using the seat warmer:
The heat from the seat warmer may be too
hot for some people, as indicated as
follows, and could cause a
low-temperature burn.
Infants, small children, elderly people,
and physically challenged people
People with delicate skin
People who are excessively fatigued
People who are intoxicated
People who have taken sleep-inducing
medicine such as sleeping pills or cold
medicine
Do not use the seat warmer with anything
having high moisture-retention ability such
as a blanket or cushion on the seat:
The seat may be heated excessively and
cause a low-temperature burn.
2-6
*Some models.
Essential Safety Equipment
Seats
Do not use the seat warmer even when
taking a short nap in the vehicle:
The seat may be heated excessively and
cause a low-temperature burn.
Do not place heavy objects with sharp
projections on the seat, or insert needles or
pins into it:
This could cause the seat to become
excessively heated and result in injury from
a minor burn.
CAUTION
Do not use organic solvents to clean the
seat. It may damage the seat surface and
the heater.
NOTE
•
If the ignition is switched off while the
seat warmer is operating (High, Mid or
Low) and then switched ON again, the
seat warmer will automatically operate
at the temperature set before switching
off the ignition.
•
Use the seat warmer when the engine is
running. Leaving the seat warmer on for
long periods with the engine not running
could cause the battery power to be
depleted.
•
The temperature of the seat warmer
cannot be adjusted beyond High, Mid
and Low because the seat warmer is
controlled by a thermostat.
Driving Position Memory
▼
*
The desired driving position can be called
up after programming the position.
The following driving positions can be
programmed.
•
Driver’s seat position (seat slide, height
adjustment, front edge of seat bottom,
seat recline)
Refer to Seat Operation on page 2-5.
•
Active driving display (display position,
brightness level, display information)
Refer to Active Driving Display on page
4-21.
CAUTION
Do not place ngers or hands around the
bottom of the seat while the seat memory
function is operating. The seat moves
automatically while the seat memory
function is operating and ngers or hands
could get pinched and injured.
SET button
1
2
A driving position can be programmed or
operated using the buttons on the side of
the seat or the key.
*Some models.
2-7
Essential Safety Equipment
Seats
NOTE
•
Lumbar support adjustment cannot be
programmed.
•
A driving position can be progr ammed
to the buttons on the side of the seat and
the key in use for driving the vehicle.
•
If the vehicle has been serviced and the
battery cables disconnected, the
programmed seat positions will have
been erased. Re-program the seat
positions.
Programming
1. Make sure the parking brake is on.
2. Make sure the selector lever is in the P
position.
3. Start the engine.
4. Adjust the seat and the active driving
display to the desired driving position.
5. Press the SET button on the seat until a
beep sound is heard 1 time.
6. Perform 1 of the following settings
within 5 seconds of completing step 5
above:
•
Programming using a button on
the side of the seat
Press the button you want to
program, either button 1 or 2, until a
beep sound is heard 1 time.
•
Programming using the key
Press the key
button until a beep
sound is heard 1 time.
NOTE
If a beep sound is heard 3 time s, the
operation is canceled.
To move the driving position to a
programmed position
(Using a button on the side of the seat)
1. Make sure the parking brake is on.
2. Make sure the selector lever is in the P
position.
3. Start the engine.
4. Press the programming button for the
driving position you want to call up
(button 1 or 2).
5. A beep sound is heard when the
driving position adjustment is
completed.
NOTE
•
If the driving position movement is not
changed, only the beep sounds.
•
A seat position can be called up even
with the engine not running.
•
The driving position adjustment is
canceled in the following cases:
•
Any of the seat adjustment switches is
operated.
•
The SET button is pressed.
•
Programming button 1 or 2 is pressed.
•
The key button or button is
operated.
•
The vehicle starts moving.
•
The active driving display is adjusted.
(Using a programmed key)
1. Unlock the doors by pressing a request
switch or the key
button.
2. After unlocking the doors, the seat
position adjustment begins within 40
seconds of opening the driver's door,
and a beep sounds when the operation
is finished.
3. Make sure the parking brake is on.
2-8
Essential Safety Equipment
Seats
4. Make sure the selector lever is in the P
position.
5. Start the engine.
6. The active driving display adjustment
begins.
NOTE
•
If there is no driving position movement,
a beep is not heard.
•
The driving position adjustment is
canceled in the following cases:
•
Any of the seat adjustment switches is
operated.
•
The SET button is pressed.
•
Programming button 1 or 2 is pressed.
•
The key button or button is
operated.
•
The vehicle starts moving.
•
The active driving display is adjusted.
Erasing programmed driving positions
(Erasing the driving positions
programmed to the key)
1. Switch the ignition OFF.
2. Press the SET button on the side of the
seat until a beep sound is heard 1 time.
3. After the beep sounds, press the key
button within 5 seconds until a beep
sound is heard 1 time.
NOTE
If a beep sound is heard 3 times, the
operation is canceled.
Rear Seat
Split Folding the Seatbacks
▼
By lowering the rear seatbacks the luggage
compartment space can be expanded.
WARNING
Do not drive the vehicle with occupants on
folded down seatbacks or in the luggage
compartment.
Putting occupants in the luggage
compartment is dangerous because seat
belts cannot be fastened which could lead
to serious injury or death during sudden
braking or a collision.
Do not allow children to play inside the
vehicle with the seatbacks lowered.
Allowing children to play in the vehicle
with the seatbacks folded down is
dangerous. If a child enters the luggage
compartment and the seatbacks were
raised back up, the child may become
trapped in the luggage compartment
which could lead to an accident.
Tightly secure cargo in the luggage
compartment when it is transported with
the seatbacks folded down.
Driving without tightly securing cargo and
luggage is dangerous as it could move and
become an obstruction to driving during
emergency braking or a collision resulting
in an unexpected accident.
2-9
Essential Safety Equipment
Seats
When transporting cargo, do not allow the
cargo to exceed the height of the
seatbacks.
Transporting cargo stacked higher than
the seatbacks is dangerous as visibility to
the rear and sides of the vehicle is reduced
which could interfere with driving
operations and lead to an accident.
Lowering the seatbacks
CAUTION
When folding the seatback forward,
always support the seatback with your
hand. If it is not supported by a hand,
ngers or the hand pressing the push
knob could be injured.
Check the position of a front seat before
folding a rear seatback.
Depending on the position of a front
seat, it may not be possible to fold a rear
seatback all the way down because it
may hit the seatback of the front seat
which could scratch or damage the front
seat or its pocket. Remove the head
restraint on the rear outboard seat if
necessary.
Before folding a rear seatback, make sure
that the armrest is stored. If a seatback is
lowered without storing the armrest, it
could deform, damage, or scratch the
armrest.
2. Press the push knob to fold down the
seatback.
Push knob
To return the seatback to its upright
position:
WARNING
When returning a seatback to its upright
position, make sure the 3-point seat belt is
not caught in the seatback and the 3-point
seat belt is not twisted.
If the seat belt is used while it is twisted and
caught in the seatback, the seat belt
cannot function at its full capacity, which
could cause serious injury or death.
1. Lower the head restraint all the way
down.
Refer to Head Restraints on page 2-
12.
2-10
Essential Safety Equipment
Seats
When returning a seatback to its upright
position, make sure that it is rmly locked
and the red indication is not visible.
If the red indication is visible behind the
push knob, it means the seatback is not
locked. If the vehicle is driven without the
seatback locked, it could fold down
suddenly and cause an accident.
Locked position
Unlocked position
Red indication
1. Make sure that the seat belt passes
through the seat belt guide correctly
and it is not twisted, then raise the
seatback while preventing the seat belt
from being caught in the seatback.
Red indication
Seat belt guide
Armrest
▼
The rear armrest in the center of the rear
seatback can be used (no occupant in the
center seat) or placed upright.
*
WARNING
Never position the shoulder portion of a
seat belt over the armrest:
Positioning the shoulder portion of a rear
seat belt over the armrest is dangerous as it
cannot provide adequate protection in a
collision and could result in serious injuries.
Never put your hands and ngers around
the moving parts of the seat and armrest:
Putting your hands and ngers around the
moving parts of the seat and armrest is
dangerous as they could get injured.
2. Press the seatback rearward and lock it
in place. After returning the seatback
to its upright position, make sure it is
securely locked.
CAUTION
Be careful not to apply excessive force to
the armrest such as by sitting on it.
Otherwise, it could be deformed or
damaged.
*Some models.
2-11
Essential Safety Equipment
Seats
When storing the armrest, return the cup
holder to its original position. If the
armrest is stored without returning the
cup holder to its original position, the
cup holder could be deformed or
damaged.
Head Restraints
Your vehicle is equipped with head
restraints on all outboard seats and the rear
center seat. The head restraints are
intended to help protect you and the
passengers from neck injury.
WARNING
Always drive with the head restraints
installed when seats are being used and
make sure they are properly adjusted. In
addition, always raise the head restraints
on all rear seats when they are being used:
Driving with the head restraints adjusted
too low or removed is dangerous. With no
support behind your head, your neck could
be seriously injured in a collision.
Height Adjustment
▼
Adjust the head restraint so that the center
is even with the top of the passenger's
ears.
2-12
To raise a head restraint, pull it up to the
desired position.
To lower the head restraint, press the
stop-catch release, then push the head
restraint down.
Essential Safety Equipment
Seats
Front outboard seat
Rear outboard seat
Except Mexico
Mexico
Rear center seat
Removal/Installation
▼
To remove the head restraint, pull it up
while pressing the stop-catch.
To install the head restraint, insert the legs
into the holes while pressing the
stop-catch.
WARNING
Always drive with the head restraints
installed when seats are being used and
make sure they are properly installed:
Driving with the head restraints not
installed is dangerous. With no support
behind your head, your neck could be
seriously injured in a collision.
After installing a head restraint, try lifting it
to make sure that it does not pull out:
Driving with an unsecured head restraint is
dangerous as the eectiveness of the head
restraint will be compromised which could
cause it to unexpectedly detach from the
seat.
2-13
Essential Safety Equipment
Seats
CAUTION
When installing a head restraint, make
sure that it is installed correctly with the
front of the head restraint facing
forward. If the head restraint is installed
incorrectly, it could detach from the seat
during a collision and result in injury.
The head restraints on each of the front
and rear seats are specialized to each
seat. Do not switch around the head
restraint positions. If a head restraint is
not installed to its correct seat position,
the eectiveness of the head restraint
during a collision will be compromised
which could cause injury.
2-14
Essential Safety Equipment
Seat Belt Systems
Seat Belt Precautions
Seat belts help to decrease the possibility of severe injury during accidents and sudden
stops. Mazda recommends that the driver and all passengers always wear seat belts.
(Except Mexico)
All of the seat belt retractors are designed to keep the lap/shoulder belts out of the way when
not in use.
The driver's seat belt has no provisions for child-restraint systems and has only an
emergency locking mode. The driver may wear it comfortably, and it will lock during a
collision.
However, the front passenger's seat and all rear lap/shoulder belt retractors operate in two
modes: emergency locking mode, and for child-restraint systems, automatic locking mode.
While we recommend you put all children in the rear seats, if you must use the front
passenger seat for a child, slide the front passenger seat as far back as possible and make
sure any child-restraint system is secured properly.
(Mexico)
All the seats have lap/shoulder belts. These belts have retractors with inertia locks that keep
them out of the way when not in use. The locks allow the belts to remain comfortable on
users, but they will lock in position during a collision.
WARNING
Always wear your seat belt and make sure all occupants are properly restrained:
Not wearing a seat belt is extremely dangerous. During a collision, occupants not wearing
seat belts could hit someone or things inside the vehicle or even be thrown out of the vehicle.
They could be seriously injured or even killed. In the same collision, occupants wearing seat
belts would be much safer.
Do not wear twisted seat belts:
Twisted seat belts are dangerous. In a collision, the full width of the belt is not available to
absorb the impact. This puts more force on the bones beneath the belt, which could cause
serious injury or death. So, if your seat belt is twisted, you must straighten the seat belt to
remove any twists and to allow the full width of the belt to be used.
Never use one seat belt on more than one person at a time:
Using one seat belt for more than one person at a time is dangerous. A seat belt used in this
way cannot spread the impact forces properly and the two passengers could be crushed
together and seriously injured or even killed. Never use one belt for more than one person at a
time and always operate the vehicle with each occupant properly restrained.
2-15
Essential Safety Equipment
Seat Belt Systems
Do not operate a vehicle with a damaged seat belt:
Using a damaged seat belt is dangerous. An accident could damage the belt webbing of the
seat belt in use. A damaged seat belt cannot provide adequate protection in a collision. Have
an Authorized Mazda Dealer inspect all seat belt systems in use during an accident before
they are used again.
Have your seat belts changed immediately if the pretensioner or load limiter has been
expended:
Always have an Authorized Mazda Dealer immediately inspect the seat belt pretensioners
and air bags after any collision. Like the air bags, the seat belt pretensioners and load limiters
will only function once and must be replaced after any collision that caused them to deploy. A
seat belt with an expended pretensioner or load limiter is still better than wearing no seat belt
at all; however, if the seat belt pretensioners and load limiters are not replaced, the risk of
injury in a collision will increase.
Positioning the Shoulder Portion of the Seat Belt:
Improper positioning of the shoulder portion of the seat belt is dangerous. Always make sure
the shoulder portion of the seat belt is positioned across your shoulder and near your neck,
but never under your arm, on your neck, or on your upper arm.
Positioning the Lap Portion of the Seat Belt:
The lap portion of the seat belt worn too high is dangerous. In a collision, this would
concentrate the impact force directly on the abdominal area, causing serious injury. Wear the
lap portion of the belt snugly and as low as possible.
CAUTION
Belt retraction may become
For more details about cleaning the seat belts, refer to "Seat Belt Maintenance" (page 6-60).
2-16
if the belts and rings are soiled, so try to keep them clean.
dicult
Ring
Essential Safety Equipment
Seat Belt Systems
Pregnant Women and Persons with Serious Medical Conditions
▼
Pregnant women should always wear seat belts. Ask your doctor for specific
recommendations.
The lap belt should be worn SNUGLY AND AS LOW AS POSSIBLE OVER THE HIPS.
The shoulder belt should be worn across your shoulder properly, but never across the
stomach area.
Persons with serious medical conditions also should wear seat belts. Check with your doctor
for any special instructions regarding specific medical conditions.
Emergency Locking Mode
▼
When the seat belt is fastened, it will always be in the emergency locking mode.
In the emergency locking mode, the belt remains comfortable on the occupant and the
retractor will lock in position during a collision.
If the belt is locked and cannot be pulled out, retract the belt once, and then try pulling it out
slowly. If this fails, pull the belt strongly 1 time and loosen, then pull it out again slowly.
(Seat Belt with Automatic Locking Mode)
When the seat belt is fastened, it will always be in the emergency locking mode until it is
switched to automatic locking mode by pulling it all the way out to its full length. If the belt
feels tight and hinders comfortable movement while the vehicle is stopped or in motion, it
may be in the automatic locking mode because the belt has been pulled too far out. To return
the belt to the more comfortable emergency locking mode, wait until the vehicle has stopped
in a safe, level area, retract the belt fully to convert it back to emergency locking mode and
then extend it around you again.
Automatic Locking Mode
▼
*
Always use the automatic locking mode to keep the child-restraint system from shifting to
an unsafe position in the event of an accident. To enable seat belt automatic locking mode,
pull it all the way out and connect it as instructed on the child-restraint system. It will retract
down to the child-restraint system and stay locked on it. See the section on child restraint
(page 2-23).
*Some models.
2-17
Essential Safety Equipment
Seat Belt Systems
Seat Belt
Fastening the Seat Belt
▼
Seat belt tongue
Seat belt
buckle
Position the lap belt as low as possible, not
on the abdominal area, then adjust the
shoulder belt so that it fits snugly against
your body.
Keep low on
hip bone
Take up slack
Unfastening the Seat Belt
▼
Depress the button on the seat belt buckle.
If the belt does not fully retract, pull it out
and check for kinks or twists. Then make
sure it remains untwisted as it retracts.
Button
NOTE
If a belt does not fully retract, inspect it
for kinks and twists. If it is still not
retracting properly, have it inspected at an
Authorized Mazda Dealer.
Front Shoulder Belt Adjuster
▼
To raise To lower
2-18
Too high
Make sure the adjuster is locked.
Loading...