Maytag MAT14PRAWW0 Installation Guide

MA AG ®

iNSTALLATiON

COMMERCIAL WASHER

| 20=volt, 60-Hz Models

iNSTRUCTiONS D'INSTALLATION

COMMERCIALE

ModUles 120 V, 60 Hz

DE LA

Write down the model and serial numbers before installing washer.
Both numbers are listed on the model/serial rating plate located

under the lid.
Model #
Serial #

Date of Purchase

Prendre note des numeros de modele et de s@ie avant d'installer
la laveuse.

Les deux num@os sont indiques sur la plaque signaletique sous
le couvercle.

Num@o de modele
Num@o de serie
Date d'achat

W10135294A

www.maytagcommerciallaundry.com

Table of Contents

WASHER SAFETY ........................................................................ 2

iNSTALLATiON REQUIREMENTS .............................................. 3

Tools and Parts ........................................................................... 3

Location Requirements .............................................................. 3

Drain System .............................................................................. 4

Electrical Requirements ............................................................ 5

iNSTALLATiON iNSTRUCTiONS ............................................ 6

Remove Shipping Strap ............................................................ 6

Connect the Hoses .................................................................... 6

Level the Washer ...................................................................... 7

Complete Installation ................................................................ 8

Electromechanical Models ........................................................ 8

Additional Features .................................................................... 9

Table des mati res

SECURIT_: DE LA LAVEUSE ...................................................... 2

EXIGENCES D'INSTALLATION .................................................. 3

Outillage et pi_ces .................................................................... 3

Exigences d'emplacement ........................................................ 3

Systeme de vidange .................................................................. 4

Specifications electriques .......................................................... 5

iNSTRUCTiONS D'INSTALLATION .......................................... 6

Enlever la sangle d'expedition .................................................. 6

Raccordement des tuyaux ........................................................ 6

Reglage de I'aplomb de la laveuse .......................................... 7

Achever I'installation .................................................................. 8

Modeles electromecaniques .................................................... 8

Caracteristiques supplementaires ............................................ 9

WASHERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

, follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

You can be killed or seriously injured if you don't immediately

YoUinstructions.Canbe killed or seriously injured if you don't follow

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer follow basic precautions,
including the following:

[] Read all instructions before using the washer._
[] Do not wash articles that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline,
dry-cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or
explode.

[] Do not add gasoline, dry-cleaning solvents, or other

flammable, or explosive substances to the wash water.

These substances give off vapors that could ignite or
explode.

[] Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been used

for 2 weeks or more. HYDROGEN GAS IS

EXPLOSIVE. If the hot water system has not been
used for such a period, before using the washing

machine, turn on all hot water faucets and let the water

flow from each for several minutes. This will release

any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use an open flame during

this time.

SAVETHESEINSTRUCTIONS

INSTALLATIONREQUIREMENTS

[] Do not allow children to play on or in the washer. Close

supervision of children is necessary when the washer is used
near children.

[] Before the washer is removed from service or discarded,

remove the door or lid.

[] Do not reach into the washer if the drum, tub or agitator is

moving.-

[] Do not install or store the washer where it will be exposed to

the weather.

[] Do not tamper with controls.
[] Do not repair or replace any part of the washer or attempt any

servicing unless specifically recommended in this manual or in
published user-repair instructions that you understand and

have the skills to carry out.

[] See "Electrical Requirements" for grounding instructions.

Gather the required tools and parts before starting installation.

Tools needed

[] Level
[] Utility knife

[] Scissors
[] 8" or 10" adjustable wrench

[] Flat-blade screwdriver
[] Pliers

[] Bucket

Parts supplied
Remove parts bag from washer. Check that all parts were

included.
[] 1 hose clamp

[] 2 inlet hoses
[] 4 flat water hose washers
[] 2 front-leveling legs with nuts

[] 1 drain hose

You will need:
[] A water heater set to deliver 120°F (49°C) water to the washer.

[] A grounded electrical outlet located within 4 ft (1.2 m) of where

the power cord is attached to the back of the washer.
See "Electrical Requirements."

[] Hot and cold water faucets located within 4 ft (1.2 m) of the

back of the washer, and provide water pressure of 10-100 psi
(69-690 kPa). A pressure reduction valve should be used in

the supply line where inlet pressure entering the building
exceeds 100 psi (690 kPa) to prevent damage to the washer

mixing valve.

[] A level floor with a maximum slope of 1" (2.5 cm) under entire

washer.

[] A sturdy floor to support the washer weight (washer, water

and load) of 315 Ibs (143 kgs).

[] A 12" (30 cm) minimum riser to provide an air cushion and

prevent noise and damage to valves for a single washer
installation.

[] A floor drain should be provided under the bulkhead.

Prefabricated bulkheads with electrical outlets, water supply
lines and drain facilities should be used only where local

codes permit.

NOTE: Front access to the pump area is available by removing
2 No. T20 TORX ® security screws and then removing the front
panel.

IMPORTANT : Do not install or store the washer where it will be
exposed to the weather. Do not store or operate the washer in
temperatures at or below 32°F (0°C). Some water can remain in

the washer and can cause damage in low temperatures.
Proper installation is your responsibility.

® Registered trademark of TEXTRON

RecessedAreaand Closet Installation instructions

This washer may be installed in a recessed area or closet.
The installation spacing shown is in inches and is the minimum

allowable. Additional spacing should be considered for ease of
installation, servicing, and compliance with local codes and

ordinances.
If closet door is installed, the minimum unobstructed air openings

in the top and bottom are required. Louvered doors with
equivalent air openings are acceptable.

Minimum Installation Clearances

closet door

Product Dimensions

48,2 ................

(35.6 cm)

17"

o1_

(310 cm2)*

(43.2cm)

4 _

(10.2 cm)

rain.

1"./2.5cm/

(ocm) (ocm)

Recessed front view

Front view

24,2 t

(155 cm2)*

*Opening is the minimum for a closet door.

Louvered doors with equivalent air openings are acceptable.

O closet

Closet side view

door

mln.

3" (7.6 cm)

3" (7.6 cm)

[] Additional spacing should be considered for the ease of

installation and servicing.

[] Additional clearances may be required for wall, door and floor

moldings.

[] Additional spacing of 1" (2.5 cm) on all sides of the washer is

recommended to reduce noise transfer.

[] Companion spacing should also be considered.

0

H

A. 43" (109cm)

B. 38 _" (97 cm)

C. 35" (89 cm)
D. 1_"(3.8cm)

E.27¾" (70.5cm)
F:25_ " (65 cm)

G. Water inlets
H. 7" (18cm)

I. Power supply cord
,1 Water level switch & shaft

K. Label
L. 27" (68.5 cm)

M. 5 _" (13.3 cm)
N. 1" (2.5cm)

O. Drain hose
tq 5" (12.7 cm)

Standpipe Drain System

The standpipe drain requires a minimum diameter standpipe of
2" (5 cm). The minimum carry-away capacity can be no less than

17 gal. (64 L) per minute.
The top of the standpipe must be at least 39" (99 cm) high and

no higher than 72" (183 cm) from the bottom of the washer.

ElectricalShock Hazard

Plug into a grounded 3 prong outlet.
Do not remove ground prong.

Do not use an adapter.
Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

IMPORTANT : The washer must be electrically grounded in
accordance with local codes and ordinances or, in the absence of

local codes, with the National Electrical Code, ANSI/NFPA 70,
latest edition.

[] If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine

that the ground path is adequate.

[] Do not ground to a gas pipe.
[] Do not have a fuse in the neutral or ground circuit.
A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

[] A 120 volt, 60 Hz, AC only, 15- or 20-amp, fused electrical

circuit is required. A time-delay fuse or circuit breaker is

recommended. It is recommended that a separate circuit

serving only this washer be provided.

[] The washer is equipped with a power supply cord having a

3 prong grounding plug.

[] To minimize possible shock hazard, the cord must be plugged

into a mating, 3 prong, grounded-type outlet, grounded in

accordance with local codes and ordinances. If a mating
outlet is not available, it is the personal responsibility and

obligation of the customer to have the properly grounded
outlet installed by a qualified electrician.

Recommended Ground Method

The washer, when installed, must be electrically grounded in
accordance with local codes, or in the absence of local codes,

with the National Electrical Code, ANSI/NFPA 70, latest edition,
and all local codes and ordinances.

GROUNDING INSTRUCTIONS

For a grounded, cord=c_nnected washer:-

This washer must be grounded. In the event of a malfunction

or breakdown, grounding will reduce the risk of electrical

shock by providing a path of least resistance for electric

current. This washer is equipped with a cord having an

equipment-grounding conductor and a grounding plug. The

plug must be plugged into an appropriate outlet that is

properly installed and grounded in accordance with all local

codes and ordinances. _

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or serviceman if you are in

doubt as to whether the appliance is properly grounded.

Do not modify the plug provided with the appliance - if it will

not fit the outlet, have a proper outlet installed by a qualified

electrician.

For a permanently connected washer: _

This washer must be connected to a grounded metal,

permanent wiring system, or an equipment grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on

the appliance. _

INSTALLATIONINSTRUCTIONS

ii!_:_i!_x_:_i__:?',i?¸_i!!__!!illii_ii:i_iiii_:iii_:i__ iiii__:_iii:_

Remove tape that covers shipping strap. Pull to completely
remove the shipping strap with 2 cotter pins from the inside of
the washer.

Proper connection of the drain hose protects your floors from
damage due to water leakage. Read and follow these

instructions.

Connect the inlet hoses to the washer

t. The washer must be connected to the water faucets using

the new inlet hoses. Do not use old hoses. Insert new flat
washers (supplied) into each end of the inlet hoses. Firmly
seat the washers in the couplings.

A B

A. Coupling

B. Washer

2. Attach hose to bottom inlet valve opening first.

A. Shipping tape

B. Shipping strap

2_

Pull firmly to remove the end of shipping strap from the back
of the washer. The shipping strap plug must be completely

removed from the washer for the self-leveling legs to be
released.

Save the shipping strap for later use.

A

B

A. Cold water inlet valve

B. Hot water inlet valve

3. Attach second hose to top inlet. Tighten couplings by hand;
then use pliers to make an additional two-thirds turn.

NOTE: Inlet valve threads are plastic. Do not strip or cross-
thread.

Connect the drain hose

NOTE: Slide washer onto cardboard or hardboard before
moving across floor.

t. Move washer close to final position.

2. Put "hook" end of drain hose into laundry tub or standpipe.

3. Estimate the length of drain hose needed when washer is in
final position. Hose must be cut exactly to length so "hook"

end is held tightly over edge of standpipe.