PPrriioorrii
IInnssttrruuccttiioonn MMaannuuaall
www.maxi-cosi.com
Eng. 4358-4274
Read all instructions BEFORE
USING this child restraint.
KEEP INSTRUCTIONS FOR FUTURE USE.
Para recibir las instrucciones en español, llame
al 1-800-544-1108 o solicitarse por escrito al
dirección por arriba.
IMPOR TANT!
Failure to follow the warnings on the
labels and in the instruction manual
can result in the death or serious injury
of your child.
Weight:
5-40 pounds
(2.3-18 kg)
Height:
19-43 inches
(48-110 cm)
This child
restraint is
designed for use
by children
whose:
Replacement Parts List
NOTE: If requested color is not available, similar
color will be substituted.
P
art Cost Qty Total Cost
Crotch Strap/Buckle $4.99 X ______= $ ______
Harness Strap . . . .$2.00 X______= $ ______
Pad Set . . . . . . . .$42.00 X ______= $ ______
Harness Retainer .$1.50 X ______= $ ______
Locking Clip . . . . .$2.50 X ______= $ ______
Tether Kit . . . . . . . .$9.99 X______= $ ______
Latch Kit . . . . . . .$24.99 X______= $ ______
Instructions . . . . . .$0.00 X ______= $ ______
Merchandise Total
$
______
Shipping and handling:
$
______
SSaalleess TTaaxx
$
______
(Indiana, California, Arkansas, and Massachusetts
residents add applicable sales tax.)
GGrraanndd TToottaall
$
______
No shipping and handling on instructions for quantities
under 6. Add $.50 for each instruction over 6, then add
applicable shipping and handling.
Up to $25.00 . . . . . . . . .$5.95
$25.01 to $50.00 . . . . .$6.95
$50.01 to $75.00 . . . . .$8.95
$75.01 to $100.00 . . . .$9.95
$75.01 to $100.00 . . . .$9.95
$100.01 to $150.00 . . .$10.95
$150.01 to $200.00 . . .$11.95
$2001.01 and up . . . . .$13.95
Outside ContinentalUS . .$10.00
Fill Out For Credit Card
Visa Mastercard
Card Exp. Date: ________________________
Cardholder’s Name: ____________________
Card Number: ________________________
Signature ____________________________
CUT ON DOTTED LINE
50
4358-4274 US Priori 5/25/07 8:33 AM Page 1
Thank you for choosing this car seat, referred
to throughout this manual as a child restraint.
The Maxi-Cosi Brand is part of the Dorel
Juvenile Group (DJG) family that is committed
to creating a child restraint with the most
comfort and convenience available today.
Remember, parents are a child’s first teachers
and examples. If you always buckle your seat
belt, your child will think it is the natural thing
to do. Make it a firm rule that the vehicle does
not go until everyone is buckled up. Make no
exceptions.
No one can predict if use of a child restraint
will prevent injury or death in a particular
crash. However, combined with careful
driving, proper use of a child restraint can
lower a child’s risk of injury or death in most
crashes.
Your child’s safety is worth the time it will take
to read and follow these instructions. After
reading, if you still have questions or have any
problems with this child restraint, please
contact our Consumer Relations Department
at:
Dorel Juvenile Group, Inc.
Website: www.maxi-cosi.com
Fax: 1-800-207-8182
Mailing Address:Dorel Juvenile Group, Inc.
P.O. Box 2609
Columbus, IN 47202-2609
Telephone: 1-800-951-4113
7 A.M. to 6 P.M. EST M-TH
7 A.M. to 4:30 P.M. EST FRI
Before You Begin...
On the recline foot there is an expiration date for
use of this child restraint. Do not use this seat
after the expiration date.
Table of Contents
Table of Contents . . . . . . . . . . . . . . . . .1
General and Warm Weather Use . . . . .2
Registration and Recall . . . . . . . . . . . . .2
Warnings . . . . . . . . . . . . . . . . . . . . . .3-5
Aircraft Installation . . . . . . . . . . . . . . . .5
Understanding Your Vehicle . . . . . . . .6-7
Child Restraint Parts . . . . . . . . . . . . .8-9
Choosing Restraint and Position . . . . .10
Reclining the Child Restraint . . . . . . . .11
Accessories . . . . . . . . . . . . . . . . . . . .11
Preparing Child Restraint to
Fit Your Child . . . . . . . . . . . . . .12-15
Securing Your Child in the
Child Restraint . . . . . . . . . . . . .16-17
Removing Your Child From the
Child Restraint . . . . . . . . . . . . . . .18
Choosing LATCH or Vehicle Belts . . . .19
Knowing Your Vehicle Belts . . . . . .20-21
Locking Clip Rear-Facing Only . . .22-23
Rear-Facing Use . . . . . . . . . . . . . . . . .24
Rear-Facing Installation . . . . . . . . .25-26
with Vehicle Belt . . . . . . . . . . .27-28
with LATCH . . . . . . . . . . . . . . .29-31
Forward-Facing Use . . . . . . . . . . . . . .32
Forward-Facing Installation . . . . . .33-34
with Vehicle Belt . . . . . . . . . . .35-37
with LATCH . . . . . . . . . . . . . . .38-40
Adjusting the Top Anchorage Strap . .41
Removing Seat Pad for Cleaning . .42-44
Trouble Shooting . . . . . . . . . . . . . .45-46
Warranty . . . . . . . . . . . . . . . . . . . .47-48
Replacement Parts Order Form . . .49-50
1
4358-4274 US Priori 5/25/07 8:33 AM Page 3
Child restraints could be recalled for safety
reasons. You must register this restraint to
be reached in a recall. Send your name,
address and the restraint’s model number
and manufacturing date to:
Dorel Juvenile Group, Inc.
P.O. Box 2609,
Columbus, IN 47202-2609
Attn: Consumer Relations or visit
www.maxi-cosi.com
or call 1-800-951-4113.
You can now register your child restraint
online at www.maxi-cosi.com. Please do
not send in your registration card if you
registered your child restraint online
For recall information, call the U.S.
Government's Vehicle Safety Hotline at 1888-327-4236 (TTY: 1-800-424-9153), or
go to http://www.NHTSA.gov.
General and Warm Weather
Use
To help protect your vehicle seat’s
upholstery from damage, use a seat
protector or a towel underneath and
behind child restraint.
To avoid your child being seriously burned,
take the following precautions:
1. Park in the shade or where sun does
not directly hit the child restraint.
2. Cover the child restraint with a sheet or
blanket when not in use.
3. Check for hot seat and buckles before
placing child in child restraint.
Registration and Recall
Information
WARNING
!
According to accident statistics,
children are safer when properly
restrained in the rear seating positions
than in the front seating positions.
Never place a child rear-facing
in a seating position with an
active frontal airbag.
This child restraint must always face
the rear of the vehicle and be in the fully
reclined position when the child weighs
between 5-35 lbs. (2.3-16 kg) and is less
than one year old.
Never place a child less than one-year
old forward facing.
Check vehicle instructions for more
information about air bag/child restraint
use.
For vehicles with an air bag,but
without a back seat, refer to your vehicle
owners manual.
Make sure the harness height is
correct for your child’s size.
The harness must be snug.
Do not lubricate buckles and fasteners.
Failure to follow these warnings can
result in the serious injury or death of
your child. To help you recognize those
instructions which are most critical for
your child’s safety,we use this symbol :
23
4358-4274 US Priori 5/25/07 8:33 AM Page 5
WARNING
!
The vehicle or LATCH belt must stay
tight at the belt path.When you switch
from one mode to the next, review the
sections of this instruction manual that
apply to that mode. If you don’t, your child
could be injured or killed.
Never take your child out of the child
restraint or try to tend to your child’s
needs while the vehicle is moving. Never
leave child unattended.
Do not use a child restraint with
damaged or missing parts.
Do not use cut, frayed or damaged
harnesses.
Do not substitute parts or try to modify
the child restraint in any way.
Do not use a child restraint that has
been in a crash. You must get a new child
restraint.
Use the child restraint only on vehicle
seats that face forward.Do not use on
seats that face the sides or rear of the
vehicle.
Check the vehicle or LATCH belt before
each use. Use only if the belt can be
tightened properly and securely.
Secure the top anchorage strap (tether)
provided with this child restraint as
specified in both the vehicle and child
restraint manufacturer's instructions.
Do not use this child restraint without
the seat pad.
WARNING
!
This child restraint should be securely
belted in the vehicle even when not in
use. In a crash or sudden stop, an
unsecured child restraint could injure
other occupants.
Do not use this child restraint if the
midpoint of your child’s head is above the
top of the child restraint.
Dorel Juvenile Group does not
recommend the use of any child restraint
accessories except those provided by DJG.
Never allow any child to play with this
child restraint; it is not a toy.
Do not remove any of the warning
labels or other labels on the child
restraint.
Placing your child in a hot child
restraint may result in burns.
Read instructions for other warnings.
This restraint is certified for aircraft use.
Use on forward-facing aircraft seats only
and in a position where the lap belt can be
tightened securely. This child restraint is
installed in an aircraft seat the same way it
is installed in the vehicle.
Use the child restraint only with F.A.A.
certified equipment. Contact the airline
prior to taking a child restraint on board in
order to comply with their specific
regulations.
Aircraft Installation
45
4358-4274 US Priori 5/25/07 8:33 AM Page 7
Your vehicle’s features may be
considerably different than those pictured
here. Consult your vehicle owner’s manual
to help identify your vehicle’s specific
features.
Understanding Your Vehicle
A
B
C
E
D
A. Anchor Bracket
For Top Anchorage
Strap
(Forward-Facing
Only)
B. LATCH Anchors
(In seat bight)
C. Seat Buckles
D. Air Bag
(Consult your vehicle
owner’s manual for all
air bag locations)
E. Seat Bight
(Where seat cushions
meet)
67
4358-4274 US Priori 5/25/07 8:33 AM Page 9
Child Restraint Parts
A
A. Harness Slots
B. Harness Covers
(on select models)
C. Harness Straps
D. Harness Retainer
E. Harness Strap
Holders
F. Buckle
G. Buckle Cover
(on select models)
H. Harness Release
Lever
I. Harness
Adjustment Strap
J. Cup Holder
(on select models)
K. Instructions
L. Recline Handle
M. Top Anchorage
(Tether) Strap &
Hook
N. Locking Clip
(inside recline foot)
O. Splitter Plate
(between shell and
base, under harness
guard door)
P. Shoulder Belt
Lock-Off
Q. Recline Foot
R. Base
S. Shell
T. LATCH Belt
B
C
D
E
E
F
G
H
I
J
R
K
M
N
O
T
Q
S
P
L
89
4358-4274 US Priori 5/25/07 8:33 AM Page 11
Install Cup Holder
(on select models):
Hook cup holder on
side of shell. Make
certain both top and
bottom of cup holder
snaps into place.
Cup holder can be installed on either side.
This child restraint
has 4 recline
positions: Upright, 2
semi recline
positions, and
reclined.
Squeeze recline
handle to recline.
Rear-Facing - Must be fully reclined.
Forward-Facing - Can use any of the 4
positions.
Harness Covers (on
select models):
Harness covers help
provide comfort to
the neck. For
harness covers to fit
correctly, you may
have to fit the upper
ends of the covers
through the harness
slots. To remove, unthread harness from
harness splitter plate. Slide covers off and
reattach harness.
Choosing Restraint and
Position
Your child’s height, weight and age
determine how your child restraint should
be placed in the vehicle and which
restraint should be used.
5-35 lbs (2.3-16 kg)
19-36 in. (48-91 cm)
Rear-Facing using
5-point harness
Child and child
restraint face the
back of the vehicle
and are placed in
the back seat.
22-40 lbs
(10.1-18 kg)
34-43 in.
(85.1-110 cm)
and Over 1 Year Old
Forward-Facing using
5-point harness
Child and child
restraint face the
front of the vehicle
and are placed in
the back seat.
Reclining the Child
Restraint
2
3
Accessories
(on select models)
10 11
4358-4274 US Priori 5/25/07 8:33 AM Page 13
1.
2.
3.
4.
5
Place the child’s
bottom and back
flat against the child
restraint. This will
increase comfort
and allow the
harness to properly
tighten.
Rear-Facing Position:
Harness slot must
be even with or
just below the
shoulders.
If the bottom
harness slots are
above the child’s shoulders, do not use
this child restraint. Use an infant child
restraint instead.
Forward-Facing Position: Har ness slots
must be even with or just above the
shoulders.
If the top harness slots are below the
child’s shoulders, do not use this child
restraint. Use a belt-positioning booster
instead.
Harness
Slot
6
Check Harness Height
7
Determine which
set of harness slots
works best for your
child. Adjust if
needed.
2
Loosen harness by
pushing down on
the harness release
lever while pulling
out on the harness.
You MUST make these adjustments with your
child before you install the child restraint in
the vehicle.
Make sure LATCH
belt packaging is
pulled free of child
restraint shell.
1
3
Press on harness
retainer release
button and pull
apart.
Press red button
on buckle to
release the buckle
plates. Hook
harnesses on the
harness strap
holders on the
sides of child
restraint.
4
Preparing Child Restraint
to Fit Your Child
continued on next page.
12 13
4358-4274 US Priori 5/25/07 8:33 AM Page 15
Remove harness
from splitter plate.
10
8
To Change Harness
Location:
Place the child
restraint into the
fully reclined
position. Locate
the harness guard
door and open it by
pressing in on the
door’s tab.
9
Pull out the harness
and splitter plate.
Pull harness
through the
harness slots from
the front.
Rethread harness
into new harness
guide location.
Refasten harness
to splitter plate.
Make sure harness is
completely on
splitter plate and it
does not twist.
Close and lock the
harness guard
door.
11
WARNING
!
Failure to reattach the harness
correctly,can result in serious injury or
death.
14 15
4358-4274 US Priori 5/25/07 8:33 AM Page 17
WARNING:
Failure to fasten and tighten the harness
system correctly with each use can
result in serious injury or death.
Position the
harness retainer at
mid-chest (even
with arm pits),
away from the
child’s neck.
5
!
Pull on harness
adjustment strap to
tighten harness
snugly.
NOTE: A snug strap
should not allow
any slack. It lies in
a relatively straight
line without
sagging. It does
not press on the
child’s flesh or push
the child’s body
into an unnatural
position.
4
1
Position harness
straps over the
child’s shoulders.
Securing Your Child in the
Child Restraint
Push each buckle
plate into buckle
until you hear a
“click”. Remember
to always pull up
on harness straps
to make sure
buckle is locked
tightly.
2
3
Snap the harness
retainer together.
16 17
4358-4274 US Priori 5/25/07 8:33 AM Page 19
LATCH means
Lower Anchors and
Tethers for CHildren.
Not all vehicles
manufactured
before September
2002 were
equipped with
LA TCH.
The LATCH system
allows a child restraint to be secured in the
vehicle without using the vehicle belt
system and can ONLY be used in vehicles
that have the anchor bars installed.
Check your vehicle owners manual to see
which seating positions may be equipped
with the LATCH system.
Press on harness
retainer release
button and pull
apart.
2
1
Loosen harness by
pushing down on
the harness release
lever while pulling
out on the harness.
Press red button
on buckle to
release the buckle
plates. Place
harness over sides
of child restraint.
Remove child.
3
Removing Your Child From
the Child Restraint
Choosing LATCH or Vehicle
Belts
The LATCHSystem
Anchor bars
Vehicle Belts
If LATCH is not an
option, you will use
your vehicle’s belts.
In most cases you
will use the
lap/shoulder belt
combination.
There are some
vehicle belts that
will not work with a
child restraint or
will require special
attention. See next
page for specific
instructions.
18 19
4358-4274 US Priori 5/25/07 8:33 AM Page 21
Manual Belts
Manual lap belts
are common in the
center rear seat
and can allow the
child restraint to
loosen when it is
tilted or jarred.
After tightening the
lap belt securely, tilt
and push the child
restraint forward and to both sides. If no
loosening occurs, your child restraint
should be secure.
If loosening does occur, try the following: If
the buckle plate slides on the belt, turn
the buckle plate
over. If the buckle
slides, turn the
buckle. Refasten
the vehicle lap belt.
The release button
should face out
after twisting so
that it is easy to
reach in an
emergency.
If the lap belt
continues to
loosen, the child restraint must be moved
to another location in the vehicle. A
locking clip will not correct this problem;
see your vehicle owner’s manual.
Not all vehicle belts will work with this child
restraint. You must determine if your
vehicles belts are compatible with this child
restraint. If you will use the LATCH system,
refer to the LATCH section.
ELR - Emergency Locking Retractor Belts
Definition: These belts only lock in a sudden
stop or crash. To see if you have this type of
belt, pull on the lap belt, let it return part way,
then pull on it again. If it moves freely, it is an
ELR belt and the child restraint could work
loose during normal driving. Refer to your
vehicle owner’s manual. Some ELR belts will
convert to Automatic Locking Retractor
(ALR) belts if you pull the belt all the way out.
Refer to your vehicle owner’s manual.
ELR shoulder belts either require a locking
clip or cannot be used with any child
restraint.
ELR lap-only belts must be replaced with a
manual belt; contact your vehicle dealer. A
locking clip will not correct this problem.
Automatic/Passive vehicle seat belts
Automatic (passive) 2-point belt has no lap
belt. You must install a lap belt to secure a
child restraint. You may also need to install
an extra lap belt for an automatic 3-point
belt. Refer to the vehicles owner’s manual. A
locking clip will not correct this problem.
Vehicle belt too short
Contact your vehicle dealer for a seat belt
extender.
Belts in center of the door or side panel (A) or
middle of the vehicle seat cushion (B).
You must move
the child restraint
to another
seating location.
A locking clip will
not fix this
problem.
See “Locking Clip” section.
Knowing Your Vehicle Belts
A
B
Buckle
Twist vehicle seat
belt and latch plate
(or buckle)
Latch plate
WARNING
!
Failure to check and adjust the manual
belt as described above can result in
serious injury or death.
1
2
20 21
4358-4274 US Priori 5/25/07 8:33 AM Page 23
Locking Clip:
Rear-Facing Only
NOTE: Remove the locking clip when the
seat belt is not being used with a child
restraint. The locking clip is located on the
recline foot. A locking clip will not fix all types
of seat belt problems. The locking clip is
not used in the forward-facing mode of use
because this child restraint uses shoulder
belt lock-offs.
Before you put your child restraint in the
vehicle in the rear-facing mode of use, buckle
the lap/shoulder belt. Pull on the lap belt
portion. If it loosens or slips, you must either
use a locking clip to hold the seat belt tight
or move the child restraint to another seating
location.
1
2
Thread both vehicle
lap and shoulder
belts through the
slot (as shown) and
out other side.
Buckle. Pull up on
shoulder belt until
all slack is out and
lap belt is tight.
Grasp both vehicle
belts together just
behind the buckle
plate and unbuckle.
NOTE: If the buckle
plate ends up
behind the child
restraint, grasp the
belts to the outside
of the child
restraint, as close to
the buckle plate as
possible.
3
5
Rebuckle belt. Lap
belt portion should
now be tight. If
not, remove
locking clip and
repeat all steps.
Thread both
portions of the
vehicle belt onto
the locking clip.
Position locking
clip about 1 in. (2.5
cm) from vehicle
belt’s buckle plate.
4
22 23
4358-4274 US Priori 5/25/07 8:33 AM Page 25
Rear-Facing Use
Lap/Shoulder Belt
LATCH Belt
WARNING:
!
Refer to the
“Choosing
Restraint and
Position” section to
determine if your
child should be in
the rear-facing
position.
This child restraint must always face
the rear of the vehicle and be in the
fully reclined position when the child
weighs between 5-35 lbs. (2.3-16 kg)
and is less than one year old.
Never place a child rear-facing
in a seating position with an
active frontal airbag.
Rear Facing Use: 5-35 lbs. (2.3-16 kg), 19-36” (48-91 cm)
Lap Belt
Rear Facing Use: 5-35 lbs. (2.3-16 kg), 19-36” (48-91 cm)
To move the
recline foot to the
rear-facing
position, lay
restraint on it’s
side.
After deciding whether to use your
Vehicle Belts or LATCH, be sure to read
the warnings below as they pertain to
both systems.
The recline foot MUST be in the rearfacing position.
Rear-Facing Installation
continued on next page.
Unlock the recline
foot by turning
the knob 1/4
turn.
Rotate the recline
foot to the front
of the restraint
and lock into
place.
4
2
3
1
Correct position
of the recline foot
is shown.
24 25
4358-4274 US Priori 5/25/07 8:33 AM Page 27
Place child
restraint rear-
facing in the back
seat. With child
restraint in the fully
reclined position,
make sure level
line on side of
shell is level with
ground. Adjust child restraint if needed.
NOTE: Hook top anchorage strap to recline
foot (see “Adjusting the Top Anchorage
Strap” section).
A loose top anchorage (tether) strap can
result in serious injury or death.
Loose LATCH hooks can result in serious
injury or death.
When LATCH is
not being used,
fasten LATCH
hooks on side of
child restraint as
shown.
Do Not Use the top
anchorage strap in
the rear-facing
position.
Hook top
anchorage strap to
recline foot (see
“Adjusting the Top
Anchorage Strap”
section).
WARNING:
!
5
3
Rear-Facing Installation
with Vehicle Belt:
Thread the
vehicle lap or
lap/shoulder belt
combination
through the rearfacing belt slot.
Thread UNDER
seat pad behind
the crotch strap,
between crotch
strap and rear
harness slot, and
out opposite side.
Buckle vehicle
belt.
Do not place
vehicle belt over
child’s legs.
1
2
Rear Facing Use: 5-35 lbs. (2.3-16 kg), 19-36” (48-91 cm)
continued on next page.
26 27
4358-4274 US Priori 5/25/07 8:33 AM Page 29
With weakest hand
at belt path, tilt and
push the child
restraint forward
and back, and from
side to side. If the
seat belts do not
loosen, your child
restraint should be
secure.
NOTE: Some “play”
from front to back
or about an inch
from side to side is
acceptable. If it moves more, review
“Knowing your Vehicle Belts” and “The
Locking Clip” sections.
After checking for
hot seat and
buckles, secure
child as described
in “Securing Your
Child in the Child
Restraint” section.
5
WARNING
!
Using this child restraint in any vehicle
seat where the lap belt cannot be
tightened securely and properly or
where it can be loosened by pulling on
it can result in serious injury or death.
4
Push down firmly
on the child restraint
and pull up on belt
to tighten. For a
manual belt, refer to
“Knowing your
Vehicle Belt”
section. Pull up on
shoulder strap to
remove any slack.
NOTE: Locking clip
is shown installed.
6
1
Rear-Facing Installation
with LATCH
To thread the
LATCH belt, put
belt end with
connector and
adjuster through
the rear-facing
belt path slot.
NOTE: Do not use the LATCH system
along with the adult lap or lap/shoulder
belt.
Rear Facing Use: 5-35 lbs. (2.3-16 kg), 19-36” (48-91 cm)
2
Thread UNDER
seat pad behind
the crotch strap
and out opposite
side.
Do not place
vehicle belt over
child’s legs.
3
Adjuster MUST be
on the left side of
child restraint as
shown. DO NOT
twist belt.
continued on next page.
28 29
4358-4274 US Priori 5/25/07 8:33 AM Page 31
Place child restraint
rear-facing in the
back seat. With
child restraint in the
fully reclined
position, make sure
level line on side of
shell is level with
ground. Adjust
child restraint if needed.
NOTE: Hook top anchorage strap to recline
foot (see “Adjusting the Top Anchorage
Strap” section).
5
Fasten one LATCH
belt connector to
the anchor in the
vehicle seat located
in the vehicle seat
bight. Repeat for
other side of child
restraint. See your
vehicle owner’s
manual for more
information.
4
7
Push down firmly
on the child
restraint and pull
up on the loop to
tighten belt.
With weakest
hand at belt path,
tilt and push the
child restraint
forward and
back, and from
side to side. If the
LATCH belts do
not loosen, your
child restraint
should be secure.
NOTE: Some “play” from front to back or
about an inch from side to side is
acceptable.
If the child restraint does not remain tight,
do not use the child restraint in this
seating location with this LATCH system.
After checking for
hot seat and
buckles, place
child in child
restraint. See
“Securing Your
Child in the Child
Restraint” section.
8
9
WARNING
!
LATCH hooks MUST be securely
fastened. Failure to do this can result
in serious injury or death.
10
To Release LATCH:
Remove LATCH
from vehicle
anchors by
pressing the red
release button on
each connector.
Rear Facing Use: 5-35 lbs. (2.3-16 kg), 19-36” (48-91 cm)
30 31
6
NOTE: Make sure
arrows on
connectors are
facing up.
4358-4274 US Priori 5/25/07 8:33 AM Page 33
Forward-Facing Use
Lap/Shoulder Belt
LATCH Belt
Lap Belt
WARNING:
!
Using this child restraint in any vehicle
seat where the lap or LATCH belts
cannot be tightened securely and
properly or where it can be loosened
by pulling on it can result in serious
injury or death.
Check vehicle owner’s manual for
more information about airbag/child
restraint use.
Refer to the
“Choosing Restraint
and Position”
section to make
sure your child is at
the proper weight
and height to face
forward.
Forward-Facing Use: 22-40 lbs. (10.1-18 kg), 34-43” (85.1-110 cm), Over 1 year of age.
Forward-Facing Installation
To move the
recline foot to the
forward-facing
position, lay
restraint on it’s
side.
After deciding whether to use your
Vehicle Belts or LATCH, be sure to read
the warnings below as they pertain to
both systems.
The recline foot MUST be in the forwardfacing position.
Unlock the recline
foot by turning
the knob 1/4
turn.
Rotate the recline
foot to the back
of the restraint
and lock into
place.
4
2
3
1
Correct position
of the recline foot
is shown.
continued on next page.
Forward-Facing Use: 22-40 lbs. (10.1-18 kg), 34-43” (85.1-110 cm), Over 1 year of age.
32 33
4358-4274 US Priori 5/25/07 8:33 AM Page 35
A loose top anchorage (tether) strap can
result in serious injury or death.
Loose LATCH hooks can result in serious
injury or death.
When LATCH is
not being used,
fasten LATCH
hooks on side of
child restraint as
shown.
Hook top
anchorage strap to
recline foot (see
“Adjusting the Top
Anchorage Strap”
section).
WARNING:
!
5
Forward-Facing Use: 22-40 lbs. (10.1-18 kg), 34-43” (85.1-110 cm), Over 1 year of age.
Place child
restraint flush
against the back
of the vehicle seat
forward-facing in
the back seat.
Forward-Facing
Installation with Vehicle
Belts
1
Thread the
vehicle lap belt or
lap/shoulder belt
combination
through the belt
path and out
other side.
Buckle.
2
Reline the child
restraint to open
the belt bath
area.
4
Open the lock-off
opposite of the
vehicle buckle by
press down on
the lock-off’s tab.
3
continued on next page.
34 35
4358-4274 US Priori 5/25/07 8:33 AM Page 37
Thread the
shoulder belt
through the lock-off
on the opposite side
of the vehicle buckle.
Close the lock-off.
Lock by lifting up
the tab to the
locked position.
5
6
Place one knee in
the child restraint
and push down
firmly while pulling
up on shoulder belt
to tighten. For a
manual belt, refer
to “Knowing your
Vehicle Belt”
section.
With knee still in
child restraint,
attach hook to
anchor in vehicle.
Push down firmly
and tighten top
anchorage strap.
To adjust top anchorage strap: See
“Adjusting Top Anchorage Strap” section.
NOTE:
If your vehicle does not have an
anchor bracket, hook the top anchorage
strap’s hook to recline foot
(see
“Adjusting the Top Anchorage Strap”
section)
.
7
With weakest
hand at belt path,
tilt and push the
child restraint
forward and
back, and from
side to side. If
the seat belts do
not loosen, your
child restraint
should be
secure.
NOTE: Some
“play” from front to back or about an
inch from side to side is acceptable. If it
moves more, review “Knowing Your
Vehicle Belts”.
8
WARNING
!
Using this child restraint in any vehicle
seat where the lap belt cannot be
tightened securely and properly or
where it can be loosened by pulling on
it can result in serious injury or death.
After checking for
hot seat and
buckles, place
child in child
restraint. See
“Securing Your
Child in the Child
Restraint” section.
9
Recline the child
restraint to any of
the 4 positions.
10
Forward-Facing Use: 22-40 lbs. (10.1-18 kg), 34-43” (85.1-110 cm), Over 1 year of age.
36 37
4358-4274 US Priori 5/25/07 8:33 AM Page 39
1.
2.
3.
4.
Forward-Facing Use: 22-40 lbs. (10.1-18 kg), 34-43” (85.1-110 cm), Over 1 year of age.
Forward-Facing Installation
with LATCH Belt
1
2
Recline child
restraint. To thread
the LATCH belt,
put belt end with
connector and
adjuster through
the forward -facing
belt path slot.
NOTE: Do not use the LATCH system
along with the adult lap or lap/shoulder
belt.
Adjuster MUST be
on the left side of
child restraint as
shown. DO NOT
twist belt.
3
Place child restraint
flush against the
back of the vehicle
seat forward-facing
in the back seat.
4
Fasten one
LATCH belt
connector to the
anchor in the
vehicle seat
located in the
vehicle seat bight.
Repeat for other
side of child
restraint. See
your vehicle
owner’s manual
for more
information.
6
Place one knee
in the child
restraint and
push down firmly
while pulling up
on loop end of
the LATCH belt
to tighten.
With knee still in
child restraint,
attach hook to
anchor in vehicle.
Push down firmly
and tighten top
anchorage strap.
To adjust top
anchorage strap:
See “Adjusting
Top Anchorage
Strap” section.
7
continued on next page.
38 39
5
NOTE: Make sure
arrows on
connectors are
facing up.
4358-4274 US Priori 5/25/07 8:33 AM Page 41
With weakest hand
at belt path, tilt and
push the child
restraint forward and
back, and from side
to side. If the
LATCH belts do not
loosen, your child
restraint should be
secure.
NOTE: Some “play” from front to back or
about an inch from side to side is
acceptable.
If the child restraint does not remain tight,
do not use the child restraint in this seating
location with this LATCH system.
8
WARNING
!
LATCH hooks MUST be securely
fastened. Failure to do this can result in
serious injury or death.
After checking for
hot seat and
buckles, place
child in child
restraint. See
“Securing Your
Child in the Child
Restraint” section.
9
6
To Release LATCH:
Remove LATCH
from vehicle
anchors by
pressing the red
release button on
each connector.
The top anchorage strap is used for the
forward-facing position only.
Most vehicles made after 9/1/99 already
have the anchor hardware for a top
anchorage strap. Refer to your owner’s
manual or call your dealer.
Storage of Top
Anchorage Strap:
Hook the top
anchorage strap
hook to the
recline foot in
either forward-
facing or rear-facing mode of use.
Adjusting the Top
Anchorage Strap
Pull loose
end to
tighten
Lift up to
loosen
To Attach Top
Anchorage Strap:
Put knee in child
restraint and
push down;
attach hook to
anchor in vehicle.
To Adjust Top
Anchorage Strap:
To tighten; pull on
free end of top
anchorage strap.
To loosen; lift up
on top
anchorage lock
and push lock
toward top
anchorage hook.
Forward-Facing Use: 22-40 lbs. (10.1-18 kg), 34-43” (85.1-110 cm), Over 1 year of age.
40 41
4358-4274 US Priori 5/25/07 8:33 AM Page 43
Removing Seat Pad for
Cleaning
WARNING
!
Do not use this child restraint without
the seat pad. Failure to do this can
result in serious injury.
Remove harness
from splitter plate.
2
Place the child
restraint into the
reclined position.
Locate the harness
guard door and
open it by pressing
in on the door’s
tab.
3
Pull out the harness
and splitter plate.
From the front, pull
harness out of shell
and pad.
4
1
Loosen harness by
pushing down on
the harness release
lever while pulling
out on the harness.
Undo harness
retainer and
unbuckle the
buckle.
From the back of
the restraint, pull
pad out from the
tabs (shown in red).
5
6
continued on next page.
42 43
4358-4274 US Priori 5/25/07 8:33 AM Page 45
From the front, pull
pad off the shell,
starting at the top.
Lift pad over the
harness strap
holders and work
the pad around the
harness adjustment
cover.
Hand wash with
warm sudsy water,
rinse clean and air
dry. Do not use
bleach or other
harsh cleaners. Do
not dry clean.
Spot clean harness
straps. Do not
machine wash.
Replace pad by
reversing order.
Reinstall harness
(see “Preparing
Child Restraint to
Fit Your Child”
section).
7
1. If your child restraint is not held securely
by the belt:
Press down firmly on the child restraint
and remove all the slack in the belt. Make
sure the belt buckle is not up against the
child restraint where the belt cannot be
tightened. Review “Locking Clip” and
“Adjusting the Top Anchorage Strap”
sections. If you cannot secure the child
restraint tightly, move it to another seating
location.
2. If the child restraint buckle or harness
adjustment lever sticks or you cannot get the
straps tight enough around child:
DO NOT LUBRICATE. Check around
buckle and harness release lever for
dropped food, sticky spilled drinks, dirt,
leaves, etc.
Clean with warm water and/or
remove object with tweezers.
If you cannot
get the harness to adjust and remain tight
with the buckle securely locked, do not
use the child restraint.
3. If your harness twists or ropes:
Straighten the harness each time you put
your child in the seat to help prevent
twisting. Lock the buckle and tighten
harness and it will be ready for next use.
Troubleshooting
continued on next page.
44 45
4358-4274 US Priori 5/25/07 8:33 AM Page 47
Warr anty
Dorel Juvenile Group, Inc. (DJG) warrants this
product to the original retail purchaser as
follows:
This product is warranted against defective
materials or workmanship for one year from
the date of original purchase. An original
receipt is required to validate your warranty. DJG
will, at its option, provide replacement parts or
replace this product. DJG reserves the right to
substitute if the part or model has been
discontinued.
To make a claim under this warranty you may
contact us at www.maxi-cosi.com, fax us at 1800-207-8182 24 hours a day, write to DJG,
Consumer Relations Department, P. O. Box
2609, Columbus, IN 47202-2609, or call 1800-
951-4113
from 7:00 a.m. to 6:00 p.m.
EST Monday through Thursday and from 7:00
a.m. to 4:30 p.m. on Friday. Proof of purchase
is required and shipping charges are the
responsibility of the consumer.
Warranty Limitations:
This warranty does not include damages which
arise from misuse or abuse of this product.
Limitation of Damages:
The warranty and remedies as set forth are
exclusive and in lieu of all others, oral or
written, expressed or implied. In no event will
DJG or the dealer selling this product be liable
to you for any damages, including incidental or
consequential damages, arising out of the use
or inability to use this product.
Limitation of warranties and other warranty terms
and state law rights:
Any implied warranties, including implied
warranties of the merchantability and fitness for
a particular purpose, shall be limited to the
duration and terms of the express written
WARNING
Using padding that tilts the base of the
child restraint farther back than the
level-to-ground line can result in serious
injury or death.
!
4.If your infant sits
too upright in the rearfacing position: If
your vehicle seat
slopes so much that
your infant is sitting
upright, you may
place a rolled towel
under the front of the
child restraint so that the level line on the
shell’s side is level (horizontal). Check often to
be sure padding is still in place and the vehicle
belt is tight.
continued on next page.
46 47
4358-4274 US Priori 5/25/07 8:33 AM Page 49
warranty. Some states do not allow limitations
as to how long an implied warranty lasts or the
exclusion or limitation of incidental or
consequential damages, so the above
limitations may not apply to you. This warranty
gives you specific legal rights, and you may
have other rights, which vary from state to
state. Neither DJG nor the dealer selling this
product authorized any person to create for it
any other warranty, obligation, or liability in
connection with this product.
PLEASE COMPLETE AND MAIL THE PREADDRESSED OWNER REGISTRATION CARD
WITHIN (30) DAYS OF PURCHASE TO
EXPEDITE
WARRANTY CLAIMS AND TO
VERIFY THE ORIGINAL DATE OF
PURCHASE.
Replacement Parts Order Form
Complete the form below. Your model
number with color code and manufacturer
date code MUST be included on the form to
ensure proper replacement parts. Your model
number with color code and the date code
can be found on a sticker on the bottom of
the child restraint. Payment in U.S. dollars
must accompany your order. Choose parts
needed from the list on the next page.
Return the form with payment to:
Dorel Juvenile Group, Inc.
Consumer Relations Department
P.O. Box 2609
Columbus, IN 47202-2609
Fax orders to: 1-800-207-8182
Please make money orders payable to Dorel
Juvenile Group, Inc. Fill in the area below to
charge to Visa or Mastercard. We do not
accept personal checks or Discover Card. All
outside of U.S. and Canada MUST use credit
card.
We MUST have this information to
process your order:
Model Number
(5 digits & 3 letters): __________________
Manufacture Date (mm/dd/yyyy):
______________________________________
Ship To (Please Print): ___________________
Name: _________________________________
Address: _______________________________
City: ___________________________________
State/Province:_________________Zip:______
Telephone: _____________________________
Email Address: _________________________
48 49
4358-4274 US Priori 5/25/07 8:33 AM Page 51
Loading...