Maxi-Cosi Mobi User Manual [nl]

Maxi-Cosi Mobi (XP)

01 02 03

1

2

01 02 03

1

2

01 02 03

04 05 06

1

2

01 02 03

04 05 06

07 08 09

10 11 12

13 14 15

13 14 15

16 17 18

Maxi-Cosi Mobi (XP)

2

EN Instructions for use / Warranty 7 - 18

DE Bedienungsanleitung / Garantie 19 - 30

www.maxi-cosi.com

NL Gebruiksaanwijzing / Garantie 31 - 42

11

1

1

6

2

7

12

3

8

13

4

9

14

5

10

15

NEDERLAND

Dorel Netherlands

P.O. Box 6071

5700 ET Helmond

Nederland

www.maxi-cosi.com

www.maxi-cosi.com

DOREL GERMANY

Augustinusstrase 9 c
D-50226 Frechen-Konigsdorf
DEUTSCHLAND

DRU1217A14

EN Instructions for use/Warranty

IMPORTANT: Keep for future reference

DE Bedienungsanleitung / Garantie
Wichtig! Für zukünftige Zwecke aufbewahren

The safe world of Maxi-Cosi

NL Gebruiksaanwijzing/Garantie

BELANGRIJK: Bewaar de gebruiksaanwijzing als
referentie voor een later gebruik.

Contents

16

2

17

Illustrations

18

19

20

3

13 14 15

16 17 18

19 20 21

2

1

2

1

2

1

2

1

25 26 27

2

1

2

1

2

1

2

1

2

3

1

3

2

1

2

1

25 26 27

28 29 30

31 32 33

2

1

2

1

3

2

1

2

1

2

1

3

2

2

1

2

1

1

2

3

1

3

2

1

2

25 26 27

28 29 30

31 32 33

2

1

2

1

1

2

3

1

3

2

1

2

2

1

1

3

2

1

2

2

1

2

1

2

1

1

2

3

2

1

2

1

37 38 39

1

2

1

2

1

2

1

1

2

1

2

3

2

1

2

1

2

1

37 38 39

40 41 42

1

2

1

2

3

2

1

2

1

2

1

1

2

2

1

1

2

1

2

3

4

1

2

1

2

1

2

3

2

1

2

1

2

1

37 38 39

40 41 42

43 44 45

1

2

1

2

1

2

3

2

1

2

1

1

2

1

2

2

1

49 50 51

1

2

XP1 XP2 XP3

1

2

XP1 XP2 XP3

XP4 XP5 XP6

1

2

1

2

XP1 XP2 XP3

XP4 XP5 XP6

XP7 XP8 XP9

1

2

Mobi XP

Mobi

Mobi XP

Mobi

Mobi XP

Mobi

1

2

1

2

25 26 27

28 29 30

31 32 33

1

2

1

2

25 26 27

28 29 30

31 32 33

34 35 36

1

2

37 38 39

40 41 42

Mobi XP

Mobi

Mobi XP

Mobi

Mobi XP

Mobi

2

1

21

26

31

36

1

3

22

1

2

27

3

2

32

37

1

Illustrations

23

28

1

1

2

33

1

2

38

24

1

2

29

34

39

25

30

35

40

41

46

51

XP4

4

2

42

1

2

3

4

2

1

47

52

1

2

XP5

43

48

XP1

XP6

Illustrations

44

2

1

49

XP2

XP7

45

50

XP3

XP8

2

XP9

1

2

XP14

XP19

XP24

5

XP10

XP15

XP20

XP11

XP16

XP21

XP25

Illustrations

XP12

XP17

XP22

XP13

XP18

XP23

6

www.maxi-cosi.com

Dear parents

Congratulations on your purchase of the Maxi-Cosi Mobi (XP).

Safety, user-friendliness, comfort and design were given top priority during all stages of the development
of the Maxi-Cosi Mobi (XP). This product meets the most stringent safety regulations. The Maxi-Cosi Mobi
(XP) offers maximum safety only when used in accordance with these instructions.

Continuous research by our development team, supported by intensive contact and consultation with test
persons and customers, ensures that we are kept fully up-to-date in the field of child safety. Therefore, if
you have any questions concerning the use of the Maxi-Cosi Mobi (XP), please do not hesitate to contact us.

Dorel

11

10

EN

LEGEND

1. Removable cover

2. Shell

3. Base

4. Belt yoke

5. User manual

6. Tetherset

7. Control button support leg

8. Foot support leg

9. Support leg

10. Belt portion

11. Dashboard supports

12. Harness slots

13. Belt pads

14. Belt buckle

15. Adjustment button

16. Adjuster belt

17. Positioning handle

18. Frame

19. Shoulder belt

20. Belt hook

21. Car kit

22. Metal attachment hooks

English

7

EN

CONTENTS

1. IMPORTANT: READ FIRST! ...............................................8

2. INSTALLING AND REMOVING THE Maxi-Cosi Mobi (XP).........................9

2.1 Installing the Maxi-Cosi Mobi (XP) ..........................................9

2.2 Removing the Maxi-Cosi Mobi (XP) .........................................12

3. PLACING AND SECURING YOUR CHILD .....................................13

3.1 Use of the harness system: closing and tightening the harness ....................13

3.2 Seat positions (adjusting the seat into sitting and reclining positions) ...............13

3.3 Removing your child.....................................................14

3.4 Support Pillow .........................................................14

4. MAINTENANCE AND CLEANING ............................................14

4.1 General ...............................................................14

4.2 Seat cover.............................................................14

4.3 Belt buckle functioning and cleaning.........................................15

5. GENERAL INSTRUCTIONS ................................................15

6. ACCESSORIES .........................................................16

7. WASTE SEPARATION ....................................................16

8. NEXT STAGE CHILD RESTRAINTS (RECOMMENDED) ...........................17

9. CAR FITTING LIST ......................................................17

10. WARRANTY ...........................................................17

11. QUESTIONS ...........................................................18

1. IMPORTANT: READ FIRST!

The Maxi-Cosi Mobi (XP) is for rearward-facing use only. Do not use it forward facing!

Read this user manual carefully and save it for future reference in the space provided at the bottom of the
Maxi-Cosi Mobi (XP). Failure to follow the instructions contained in this manual could result in serious injury
to your child.

Use original accessories and manufacturer-approved parts only. Do not make any changes to this product.
If you have any problems or complaints, contact your retailer or importer.

The Maxi-Cosi Mobi (XP) has been approved according to the latest regulations in the ECE R 44/04, the
European standard for child restraints, and can be used for children aged approximately 9 months to
around 5 years (Group 1+2: 9 to 25 kg). The Maxi-Cosi Mobi (XP) is designated as “semi-universal” and
therefore suitable for installation on the seats of specific types of cars, as included in the Car List (see
Chapter 9: Car List).

Approval according to ECE R 44/04
Group Body Weight Age
Maxi-Cosi Mobi (XP) 1+2 9 – 25 kg 9 months – 5 years

8

2. INSTALLING AND REMOVING THE Maxi-Cosi Mobi (XP)

Mobi XP

Mobi

Mobi XP

Mobi

Mobi

The Maxi-Cosi Mobi (XP) can be installed with an automatic 3-point or 2-point safety belt in combination
with the tethers and support leg. To check whether your car is suitable for installing the Maxi-Cosi Mobi (XP)
with tethers and support leg, see Chapter 9: Car list.

• Installed with 3-point Yes
safety belt

• Installed with static 2-point Yes
safety belt

• On passenger seat Yes

• On left/right side of the back seat Yes

• In the middle position of the back seat Yes

• Rearward-facing Yes

• Forward-facing No

• Belt routing marking Blue

• Frontal airbag No

• Side airbag Yes

Never use the Maxi-Cosi Mobi (XP) on seats equipped with frontal airbags! This does not apply to side
airbags. Frontal airbags must be switched off when the car seat is in the front passenger seat. The
manufacturer advises that frontal airbags will be switched off or disabled by an official car-brand-dealer.

The Maxi-Cosi Mobi (XP) is only suitable for use in the listed vehicles fitted with dynamic 3-point or static
2-point safety belts, approved in accordance with ECE Regulation No. 16 or equivalent standard.

The proper threading of the seat belt is essential to your child’s safety. The seat belt must be threaded along
the blue markings on the Maxi-Cosi Mobi (XP). Never thread the belt in any other way!

EN

2.1 Installing the Maxi-Cosi Mobi (XP)

Step 1: Adapting the harnesses to your child

Before installing the Maxi-Cosi Mobi (XP), you will need to determine the proper height of the shoulder
belts for your child. The Maxi-Cosi Mobi (XP) has 3 slots for the shoulder belts. Smaller children should use
the lowest slots, while older children should use the top slots. Use the middle slot for children of medium
height, making sure the slot used is not below the child’s shoulders.

1

• Loosen the shoulder belts by pressing the adjustment button and pulling the shoulder belts towards you (1).

• IMPORTANT! Do not pull on the belt pads.

2 3

• Release the belt buckle by pressing the red button on the buckle (2). Drape the belts over the belt hooks
on the shell and flip away the belt buckle (3).

• Position your child in the Maxi-Cosi Mobi (XP) with his back straight up against the backrest.

4

• Adjust the height of the shoulder belts to a suitable height for your child (4).

• IMPORTANT! The correct height of the shoulder belts is attained when the belt disappears into the shell
slightly above the shoulders of the child.

• Remove your child from the Maxi-Cosi Mobi (XP).

Instructions for use

9

EN

Mobi XP

Mobi

Mobi XP

Mobi

Mobi XP

Mobi

• Place the Maxi-Cosi Mobi (XP) in the sleeping position (see section 3.2: Seat positions)

• IMPORTANT! Make sure the support leg is in the folded-out position to enable you to access the back of

the Maxi-Cosi Mobi (XP) (see Step 5; Positioning the support leg).

5

• Pull the shoulder belts until the belt yoke on the back appears and remove the shoulder belts from the belt
yoke (5).

• IMPORTANT! Make sure the belt buckle is locked in order to prevent the belts from twisting.

6

• Pull the shoulder belts out of the belt pads through the shell and cover. Do this on both sides (6).

7

• TIP! Loosen the top part of the cover to make it easier to remove the belts and belt pads. Remember to
reattach the cover to the shell afterwards (7).

8

• Remove the belt pads (8).

9

• From the front, thread one belt pad through the correct slot in the cover and shell and then rethread this
belt pad through the back through the adjacent slot (9).

• IMPORTANT! Make sure the strap between the belt pads lies tight against the plastic shell and does not
become entangled with the belt portion of the support leg.

• Thread the shoulder belts through the adjusted belt pads, cover and shell (10).

10

• Attach the shoulder belts to the belt yoke and check to make sure the 3 red stitching on the belt ends and

11

the belt yoke are facing the shell (11) (if not, this means the belts are twisted).

• IMPORTANT! Make sure the belts are threaded along the plastic shell, remain behind the rods and do not

12

become entangled with and stay behind the belt portion of the support leg (12).

Adjusting the height of the shoulder belts

XP1

The correct belt height of the shoulder belts is attained when the belt disappears into the shell slightly above
theshoulder of the child. Make sure that the shoulder belts fit properly over the shoulders of the child (XP1).

• Loosen the shoulder belts by pressing the release button and pulling the shoulder belts towards you as far

01

aspossible (01) Important: Do not pull the belt pads when doing so.

XP2

• Lift up the flap on the cover by the shoulder belt slots (XP2).

• To make the adjustment easier, pull the shoulder belts on top of the belt pad forward into a loop, loosening

XP3

them (XP3).

XP4

• Next, push the loop back through the opening (XP4).

XP5

• Slide the shoulder belt and the belt pad strap through the slot together into the next position (XP5). Make

XP6

sure that theshoulder belt is positioned on top of the belt pad strap in the new position (XP6). Always do
this on both sides.

• Pull the shoulder belts tight by pulling on the belts under the belt pads (XP6).

XP6
XP7

• Place the flap back in position and thread the belt pads through the correct slots in the flap and secure

them with theVelcro (XP7).

• Check whether you are able to use the belts and ensure they are not twisted.

10

Step 2: Checking for anchor points or installing the car kit

Remove the elastic band from around the tethers and let the tethers drop to the floor. There are three ways to
hook the tethers onto the anchor points in the car. Specific anchor points may already be present in the car that
can be used. If not, the car kit components or metal attachment hooks provided can serve as anchor points.
Whenever possible, use the most forward positioned anchor points to attach the tethers.

Anchor points already present in the car

• Check the passenger seat rails for anchor points.

1413

In some cars, the child seat anchor points are part of the rail itself (13). In others, there are metal child
seat anchor loops bolted to the rail, often painted blue (14).

• Check whether the hooks of the tether can be easily connected to and disconnected from the present

15

anchor points (15). If so, use these points to anchor the Maxi-Cosi Mobi (XP).

• IMPORTANT! Make sure the straps of the tethers are not twisted.

• Wait with tightening the tethers until after Step 4; Positioning the support leg.

• Wherever possible, use the most forwarded positioned attachment points for the tethers.

Extra anchor points provided with the Maxi-Cosi Mobi (XP)

The Maxi-Cosi Mobi (XP) has extra anchor points that you can use to tether the Maxi-Cosi Mobi (XP) if no
anchor points are available in your car. There are several options for doing this.
Study the bottom of the car seat and the seat rails and choose the right configuration for installation; car kit or
metal attachment hooks (both included).

a) Car kit

The (below) chart shows all possible configurations for installing the car kit components.

16

To obtain the right length, a suitable opening in the tether must be chosen (16).

• IMPORTANT! Determine the length based on the position of the Maxi-Cosi Mobi (XP) in the car (rear, middle

or front seat).

17

• Simply hook the tether hook onto the anchor point (17).

• IMPORTANT! Make sure the tether straps and car kit components are not twisted.

• Wait with tightening the tethers until after Step 4; Positioning the support leg.

b) Metal attachment hooks

Maxi-Cosi Mobi

FRONT SEAT

on

Maxi-Cosi Mobi

MIDDLE SEAT

on

Maxi-Cosi Mobi

REAR LEFT/

on

RIGHT SEAT

Car kit components
braided together as

1

single component

2

3

EN

Car kit components
attached separately

2x

1

2

3

If you can see a bolt holding down the seat rail you can use the metal attachment hooks as separate anchor loops.

• Ask your car dealer to connect the metal attachment hooks to the bolt (18).

18

• IMPORTANT! Ask your certified car dealer to connect the metal attachment hooks. Changes to the car done

by yourself can affect the warranty conditions of your car.

• Simply hook the tether hook onto the metal attachment hooks (19).

19

• IMPORTANT! Make sure the tether straps are not twisted.

• Wait with tightening the tethers until after Step 4; Positioning the support leg.

Instructions for use

11

EN

Step 3: Installation of the Maxi-Cosi Mobi (XP)

• IMPORTANT! On some seats, the belts are fitted so far forward that proper installation is not possible. If

this is the case, try another seat.

• IMPORTANT! In some cases, the buckle of the car belt may be too long and therefore sit too high against

the base of the Maxi-Cosi Mobi (XP). If this is the case, the Maxi-Cosi Mobi (XP) cannot be installed
securely and
you’ll have to choose another position in the car. If you have any questions, please contact the manufacturer.

• Place the Maxi-Cosi Mobi (XP) on the seat and, using the dashboard supports, lean it against the:

20

a) Dashboard, if installed on the front seat (20).

222421

b) Front seat(s) if installed on the left/right (21) and middle (22) of the back seat.

23

• IMPORTANT! Place the Maxi-Cosi Mobi (XP) as far as possible with the front to the back of the seat (23) and

25

make sure the marking on the plastic base is aligned with the end of the seat of the car (24). If necessary,
slide the passenger seat forward or backward until the marking is aligned with the end of the seat (25).

• Place the Maxi-Cosi Mobi (XP) in the sitting position (see section 4.2: Seat positions).

17

19

• Attach the tethers; Do not tighten until after Step 4; Positioning the support leg (17/19).

Step 4: Positioning the support leg

• IMPORTANT! When installing on the back seat, always use the support leg to ensure the safe use of the

Maxi-Cosi Mobi (XP). The support leg does not need to be used when installing on the passenger seat
(leaning against the dashboard).

26

• IMPORTANT! If the Maxi-Cosi Mobi (XP) is installed on the back seat, slide the passenger seat forward in

order to create enough space for the support leg of the Maxi-Cosi Mobi (XP) (26).

27

• Fold out the support leg by opening the Velcro strips (27).

• IMPORTANT! Make sure the support leg is folded out as far as possible. The belt portion of the support leg

28

should now be tight (28).

• Hold onto the support leg under the control button and press the control button with your thumb (29).

29

• Keep the button pressed and move the support leg downwards until it reaches the floor of the car.

• Release the control button and “click” the support leg into the locked position (30).

30

• Check to make sure the support leg is securely locked and stays in position by trying to move it up or down
without pressing the control button.

• Slide the passenger seat backwards again to create enough room for the legs of the passenger on the front

31

seat (31).

Step 5: Tightening the tethers

• IMPORTANT! Slide the passenger seat to the front to make it possible to tighten the tethers (26).

26

• Pull the tethers as tightly as possible first on the side most far from the door by pulling the tether with the

32

loop downwards as hard as you can (32). Then tighten the other s ide (32,2) and give extra tightness by
strapping it down with your foot (32,3).

• Check to make sure the Maxi-Cosi Mobi (XP) is securely and firmly installed in the car by pulling on the seat.

Step 6: Safety belt installation

• The Maxi-Cosi Mobi (XP) can be installed with a dynamic 3-point or a static 2-point safety belt:

343533

a) If you’re installing the Maxi-Cosi Mobi (XP) with a dynamic 3-point safety belt, hold the lap and shoulder

belt (33), thread them between the steel frame and the plastic base (34) and click the seat belt into the car
seat buckle (35). Also see the blue markings for proper belt routing.

b) If you’re installing the Maxi-Cosi Mobi (XP) with a static 2-point safety belt, hold the lap belt (33), thread it

343633

between the steel frame and the plastic base (34) and click the seat belt into the car seat buckle (36). Also
see the blue markings for proper belt routing.

• IMPORTANT! Make sure the seat belts are not twisted.

37

• Using the shoulder belt, pull everything to the front of the Maxi-Cosi Mobi (XP) as tightly as possible (37).
Make sure the arrow continues to be aligned with the end of the car seat.

12

Checklist …

To ensure the optimum safety of your child, check after installation to make sure that…

• The seat belts are as tight as possible and not twisted.

• If the car kit is used, it is attached properly and not twisted.

• The tethers are not twisted, are properly secured, and as tight as possible.

• If the Maxi-Cosi Mobi (XP) is installed on the back seat, the support leg is folded out as far as possible,
locked and supported against the floor of the car.

• The entire Maxi-Cosi Mobi (XP) is installed securely and firmly in the car (check by pulling on the seat).

2.2 Removing the Maxi-Cosi Mobi (XP)

• Restore the support leg to its start position by pressing the control button and moving the support leg

38

upwards (38).

• Push the support leg into its folded-up position against the plastic base (39).

39

• Secure the support leg by closing the Velcro strips (40).

40

• Loosen the tethers by pushing the silver button (41,1), pushing the part with the silver button upward

41

(41,2) and pulling on the belt with the hook attached (41,3) (keep silver button pushed in).
TIP: First push the car seat down to lighten the tension of the tethers.

• Release the tether-hooks from the anchor points. (Possibly roll them up and bind them together with an
elastic band.)

42

• Loosen the car seat belt and remove it from between the plastic base and steel frame (42).

• IMPORTANT! If the Maxi-Cosi Mobi (XP) is installed on the back seat, hold onto it while uninstalling to make
sure it does not tip over.

• Remove the Maxi-Cosi Mobi (XP) from the car.

3. PLACING AND SECURING YOUR CHILD

3.1 Use of the harness system: closing and tightening the harness

Once the shoulder belts are adjusted to the proper height as described in section 2.1, Step 1 and your child
has been placed in the seat, you can now secure your child in the seat.

• Slide the buckle sections together and “click” them into the belt buckle (43).

43

• IMPORTANT! Position the lap belt part of the harness system as low as possible in order to safely support

44

your child’s hips (44).

45

• Pull the shoulder belts tight (45,1) and remove any remaining slack from the harness system by pulling the
belts tightly using the adjuster belt (45,2).

46

• IMPORTANT! Make sure you can fit only one finger between the harnesses and your child (46). The tighter
the belts are around your child, the better the protection.

• IMPORTANT! Make sure the belt pads are positioned properly against your child’s shoulders.

• IMPORTANT! Make sure the belts are not twisted.

• If you are unable to click the buckle sections into the buckle, release the buckle by pressing the red button
and try again.

EN

If you are unable to fasten the harness belts properly or pull them tight, contact your supplier immediately
and do not use the Maxi-Cosi Mobi (XP) under any circumstances.

Always use the belt pads, as they are essential to your child’s safety.

Instruct your child to never play with the belt buckle.

3.2 Seat positions (adjusting the seat into sitting and reclining positions)

47

The Maxi-Cosi Mobi (XP) can be adjusted to 4 different positions (47).

48

• Pull the positioning handle under the front of the seat upwards, and then pull or push the seat forwards or
backwards (48).

• Release the positioning handle in the desired position and push until you hear a “click”.

Instructions for use

13

EN

Mobi XP

Mobi

Mobi XP

Mobi

Mobi XP

Mobi

Mobi XP

Mobi

Mobi XP

Mobi

Mobi

• IMPORTANT! Check to make sure the Maxi-Cosi Mobi (XP) is securely locked in the desired position by pulling

on it.

Checklist…

To ensure the optimal safety of your child, check before every trip to make sure that…

• The entire Maxi-Cosi Mobi (XP) is installed securely and firmly in the car using the belts, tether set and car kit
(if used).

• If installed on the front seat, that the Maxi-Cosi Mobi (XP) is leaning properly against the dashboard.

• If installed on the back seat, that the Maxi-Cosi Mobi (XP) is leaning properly on the folded-out support leg.

• The height of the shoulder belts is suitable for your child.

• The belts are not twisted.

• The belt pads are positioned properly against your child’s shoulders.

• Your child is securely fastened with the harnesses, and the belt buckle is locked properly.

• The belts of the Maxi-Cosi Mobi (XP) are not damaged. If so, do not use the Maxi-Cosi Mobi (XP) under
any circumstances and contact your retailer or importer immediately.

3.3 Removing your child

• Place the Maxi-Cosi Mobi (XP) in the sitting position (also see section 3.2: Seat positions).

32

• Release the belt buckle by pressing the red button on the buckle (2). Drape the belts over the belt hooks
on the shell and flip away the belt buckle (3).

• Remove your child from the Maxi-Cosi Mobi (XP).

3.4 Support Pillow (Mobi XP)

Note: Only usable with the harness belt in the lowest position.

XP8

• Pull aside the bottom two flaps above the shoulder belts on one side of the cover (XP8).

XP9

• Slide one of the plastic guides on the headrest behind the top slot in the cover (XP9)

and fasten it with the round Velcro piece.

XP10

• Close the two flaps again and secure them with the Velcro strips (XP10).

XP11

• Repeat this on the other side (XP11).

4. MAINTENANCE AND CLEANING

4.1 General

• IMPORTANT! Remove the Maxi-Cosi Mobi (XP) from the car before cleaning.

• Use lukewarm water, soap and a rag to clean the plastic parts of the seat. Do not use abrasive cleaners.

• Clean the steel parts using a damp cloth.

• IMPORTANT! Never use lubricants, not even for the moving parts on the Maxi-Cosi Mobi (XP).

14

4.2 Seat cover

A. Removing the seat cover

• IMPORTANT! Make sure the belt buckle is locked in order to prevent the belts from twisting.

• Place the Maxi-Cosi Mobi in the sleeping position (see section 3.2: Seat positions).

5

• Pull the shoulder belts until the belt yoke on the back appears and remove the shoulder belts
from the belt yoke (5).

6

• Pull the shoulder belts out of the belt pads through the shell and cover. Do this on both sides (6).

• TIP! Loosen the top part of the cover to make it easier to remove the belts and belt pads.

8

• Remove the belt pads (8).

49

• Loosen the cover (49).

• Pull the belts, belt pads, buckle sections and belt buckle through the openings in the cover (50).

50

• Remove the cover.

B. Cleaning the seat cover

• The cover and belt pads should be washed by hand (maximum of 30˚C).
Do not place them in the dryer. Also see the care instructions on the cover itself.

Tip: It is advisable to buy an extra cover when purchasing the Maxi-Cosi Mobi (XP) so that you can continue
to use the Maxi-Cosi Mobi (XP) at all times, even when washing or drying the cover.

English

Mobi XP

Mobi

Mobi XP

Mobi

Mobi

Mobi XP

Mobi

Mobi XP

Mobi

Mobi XP

Mobi

Mobi XP

Mobi

Mobi XP

Mobi

Mobi XP

Mobi

XP22

C. Reattaching the seat cover

• Place the cover back on the Maxi-Cosi Mobi.

51

• Thread the belt buckle and shoulder belts through the cover (51).

52

• Reattach the cover all around by fastening it to the hooks (52).

9

• Reattach the belt pads (9).

• IMPORTANT! Make sure the strap between the belt pads lies tight against the plastic shell and does not

become entangled with the belt portion of the support leg.

• Thread the shoulder belts through the belt pads, cover and shell (10).

10

• Attach the shoulder belts to the belt yoke and check to make sure the 3 red stitching on the belt ends and

11

the belt yoke are facing the shell (11) (if not, this means the belts are twisted).

• IMPORTANT! Make sure the belts are threaded along the plastic shell, remain behind the rods and do not

12

become entangled with and stay behind the belt portion of the support leg (12).

• Check the functioning of the harness system.

Removing the cover and belt pads

• Make sure that the seat buckle is locked in order to prevent the belts from twisting.

• The belt clamping handle must be locked, i.e. positioned against the base.

• Loosen the shoulder belts.

• Place the Maxi-Cosi Mobi XP in the sleeping position.

• Remove the shoulder belts from the belt yoke (XP12).

XP12

• Tilt the clasp on the belt pad and pull it together with the shoulder belt through the belt slots.

XP13

This is easiest to do in the uppermost vertical section (XP13).

• Remove both belt hooks by pushing the tab on the back of the seat downwards (XP14).

XP14

• Loosen the cover on all sides (XP15). Open the belt buckle.

XP15

• Pull the belts, belt pads, buckle sections and seat buckle through the openings in the cover.

• Now remove the cover. Important: Be careful when removing the cover around the edge of the

XP16

release button (XP16).

• Slide the belt pads off the belts (XP17).

XP17

Replacing the cover and belt pads

• First slide both buckle sections together and lock into the belt buckle.

• Slide the shoulder belts through the clean belt pads ensuring that the textured side of the belt pad is facing

XP18

downwards. Push the shoulder belts through the large opening of the clasp. Important: Make sure the
shoulder belts are on top of the belt pad strap (XP18).

XP19

• Open the buckle and feed the buckle, shoulder belts and buckle parts through the openings in the cover (XP19).

XP20

• Place the cover over the edges of the release button and around the adjusting handle and secure it onto the
cover pins (XP20).

XP21

• “Click” both belt hooks into position (XP21) and check to make sure they are securely fastened.

XP23

• Secure the shoulder belt clasps in the belt slots at the desired height (XP22/XP23).

• Attach the shoulder belts to the belt yoke. Important: The red stitching on the shoulder belts and belt yoke

XP24

must be facing the shell (XP24). If not, this means the belts are twisted.

• Fasten the belt buckle and close the flap on the cover (XP25) and check the functioning of the adjustment

XP25

system.

• IMPORTANT! Make sure the belts are threaded along the plastic shell, remain behind the rods and do not

12

become entangled with and stay behind the belt portion of the support leg (12).

EN

4.3 Belt buckle and belt adjustment system functioning and cleaning

The proper functioning of the belt buckle and belt adjustment system is very important for the safety of the child.
The most common reason that the buckle and/or belt adjustment system does not function properly is because
it is dirty (from dust, grime, food particles, etc.). Make sure that the belt buckle stays clean by vacuuming out all
dirt. If the belt adjustment system is not functioning properly, contact your supplier or importer immediately (see
back of instruction manual for contact details). Do not use the Maxi-Cosi Mobi (XP) under any circumstances!

The following is a list of possible causes of function failure and possible solutions.

Instructions for use

15

A. Malfunction to the belt buckle

• When opening the belt buckle, the buckle sections are released slowly.

• The belt buckle can only be opened with considerable force.

• It is difficult to click the buckle sections into the buckle (too much resistance).

• The buckle will no longer close, the buckle sections will not go together.

• There is no “click” sound when closing the buckle.

EN

B. Solving any problems

• Check the buckle for any dirt and if necessary clean by knocking the dirt out, rinsing, blowing clean

or vacuuming with a vacuum cleaner, for example.

• NOTE! Never use lubricants!

If you are unable to close the belt buckle or if you are unsure whether you have solved the problem
correctly,contact your retailer or importer immediately (see back of instruction manual). Under no
circumstancesshould the Maxi-Cosi Mobi (XP) be used.

5. GENERAL INSTRUCTIONS

Always pay close attention to the following…

• Prior to purchase, check to make sure the seat fits properly in your car.

• Always use the seat, even on short trips, as this is when most accidents occur.

• Only use the Maxi-Cosi Mobi (XP) in a car and not at home, in an airplane, boat or other recreational
vehicle. The child restraint is approved for car travel only.

• The seat must always be secured with the seat belt, tethers and, if installed on the back seat, with the
support leg, even when not in use. A loose seat could injure other passengers in a sudden stop or crash.

• Never use the Maxi-Cosi Mobi (XP) without its cover. Do not replace the cover with a cover other than the
one supplied by the manufacturer, as the cover contributes to the safety of the seat.

• Always cover up the Maxi-Cosi Mobi (XP) when the car is parked in the sun, as plastic and metal parts may
become extremely hot and discolour the fabric.

• To avoid damage to the fabric, do not remove the logos on the cover.

• Make sure that the Maxi-Cosi Mobi (XP) does not become wedged by or overloaded with heavy luggage,
adjustable seats or slamming the car door.

• Make sure that all luggage and objects likely to cause injury in the event of an accident (on the rear
window shelf for instance) are secured properly.

• If the back seat of the vehicle can be folded forward, make sure the seat back locks are fully locked before
placing a child in the Maxi-Cosi Mobi (XP) on the back seat of the vehicle.

• Take short breaks on longer trips to give your child some freedom of movement.

• Never leave your child unattended in the car.

• Save the instruction manual for future reference in the space provided under the Maxi-Cosi Mobi (XP).

• Never use a second-hand product, as you can never be certain what has happened to it.
The safety of the car seat can only be guaranteed by the manufacturer when used by the original owner.

• Replace the Maxi-Cosi Mobi (XP) after an accident, as the seat may become unsafe due to damage that is
not readily apparent.

• The manufacturer has taken into consideration the fact that car seats may cause indentations in car
upholstery. This is unavoidable, however, due to the prescribed safety standards, and because the car seat
must be installed tightly in order to protect your child. Dorel is not liable for any damage that may occur
to the car upholstery as a result of this.

16

And it goes without saying…

• Set a good example and always wear your seat belt!