Masterbuilt 20150513 Owner's Manual

Download

Page 1

Masterbuilt Manufacturing, Inc.

1 Masterbuilt Ct.

Columbus, GA 31907

Customer Service 1-800-489-1581

www.masterbuilt.com

ASSEMBLY, CARE & USE MANUAL

WARNING & SAFETY INFORMATION

ELECTRIC PATIO GRILL

MODELS 20150112, 20150213, 20150513, 20150613, 20150713

THIS PRODUCT IS FOR OUTDOOR USE ONLY

Manual Code: 9815110001 052112-02SS

Approximate assembly time : 60 minutes

Tool needed for assembly: Phillips Head Screwdriver

Use only outdoors where it is

well ventilated.

Fuel, such as charcoal briquettes, wood or heat

pellets, are not to be used in the unit.

WARNINGWARNING

This manual contains important

information necessary for the proper

and safe use of this unit.

Read and follow all warnings

and instructions before using

grill and during use.

Keep this manual for future reference.

Failure to follow these warnings and instructions properly could result in personal injury or death.

Page 2

GENERAL WARNINGS AND SAFETY INFORMATION

READ ALL INSTRUCTIONS

When using electrical appliances, basic safety precautions should always be followed including the following:

• Cannot be operated for more than

• Use GFI protected electrical outlet to reduce the risk of electrical shock.

• For outdoor use only. Do not operate in an enclosed area.

• Unit MUST be on the ground. Do not place unit on tables or counters. Do NOT move unit across uneven surfaces.

• Do not plug in electric grill until fully assembled and ready for use.

• Use only approved grounded electrical outlet.

• Do not use during an electrical storm.

• Do not expose electric grill to rain or water at anytime.

• To protect against electrical shock do not immerse cord, plug or control panel in water or other liquid.

• Do not operate any appliance with a damaged cord or plug, or after appliance malfunctions or has

3 hours.

LIMITED WARRANTY

Masterbuilt warrants its products to be free from defects in material and workmanship under proper assembly, normal use and recommended care for 90 days from the date of original retail purchase. Masterbuilt warranty does not cover paint ﬁ nish as it may burn off during normal use. Masterbuilt warranty does not cover rust of the unit. Masterbuilt requires reasonable proof of purchase for warranty claims and suggests that you keep your receipt. Upon the expiration of such warranty, all such liability shall terminate. Within the stated warranty period, Masterbuilt, at its discretion, shall repair or replace defective components free of charge with owner being responsible for shipping. Should Masterbuilt require return of component(s) in question for inspection Masterbuilt will be responsible for shipping charges to return requested item. This warranty excludes property damage sustained due to misuse, abuse, accident, damage arising out of transportation, or damage incurred by commercial use of this product.

This expressed warranty is the sole warranty given by Masterbuilt and is in lieu of all other warranties, expressed or implied including implied warranty, merchantability, or ﬁ tness for a particular purpose. Neither Masterbuilt nor the retail establishment selling this product, has authority to make any warranties or to promise remedies in addition to or inconsistent with those stated above. Masterbuilt’s maximum liability, in any event, shall not exceed the purchase price of the product paid by the original consumer/ purchaser. Some states do not allow the exclusion or limitation of incidental or consequential damages. In such a case, the above limitations or exclusions may not be applicable.

been damaged in any manner. Contact Masterbuilt Customer Service for assistance at 1-800-489-1581.

• Keep a ﬁ re extinguisher accessible at all times while operating electric smoker.

• Do not let cord hang touch hot surfaces.

• Do not place on or near a hot gas or electric burner, or in a heated oven.

• Keep children and pets away from electric smoker at all times. Do not allow children to use electric smoker. Close supervision is necessary should children or pets be in area where electric smoker is being used.

• Fuel, such as charcoal briquettes, wood or heat pellets, are not to be used in electric grill.

• Never use electric grill as a heater (READ CARBON MONOXIDE HAZARD ON FRONT COVER).

• Use electric grill only on a level, stable surface to prevent tipping.

• Electric grill is HOT while in use and will remain HOT for a period of time afterwards. Use caution.

• Do not touch HOT surfaces.

• Do not allow anyone to conduct activities around electric grill during or following its use until the unit has cooled. Electric grill is HOT during operation and remains HOT for a period of time following use.

• The use of alcohol, prescription or non-prescription drugs may impair the user’s ability to properly assemble or safely operate electric smoker.

• Avoid bumping or impacting electric grill.

California residents only: Not withstanding this limitation of warranty, the following speciﬁ c restrictions

apply; if service, repair, or replacement of the product is not commercially practical, the retailer selling the product or Masterbuilt will refund the purchase price paid for the product, less the amount directly attributable to use by the original buyer prior to the discovery of the nonconformity. Owner may take the product to the retail establishment selling this product in order to obtain performance under warranty. This expressed warranty gives you speciﬁ c legal rights, and you may also have other rights which vary from state to state.

Go Online www.masterbuilt.com

or complete and return to

Attn: Warranty Registration

Masterbuilt Mfg. Inc.

1 Masterbuilt Court - Columbus, GA 31907

Name: __________________________________ Address :___________________________ City:________________

State/Province: ________ Postal Code: ________________Phone Number: (_____) - ____________

E-mail Address:_______________________________________

• Never move electric grill when in use. Allow electric grill to cool completely before moving or storing.

WARNINGS & IMPORTANT SAFEGUARDS CONTINUED ON PAGE 2

*Model Number: ____________________ *Serial Number: ____________________

Purchase Date: _____- ______-_______ Place of Purchase: ____________________________________

*Model Number and Serial Number are located on silver label on back of unit.

Page 3

ASSEMBLY

STEP 22

Slide drip tray (7) into drip tray bracket (8) from the right side.

GENERAL WARNINGS AND SAFETY INFORMATION

• Be careful when removing food from electric grill. All surfaces are HOT and may cause burns. Use protective gloves or long, sturdy cooking tools.

• Drip tray is only for the bottom of electric grill. Do not put drip tray on cooking grate this may

ASSEMBLY IS COMPLETE

SAFE STORAGE AND MAINTENANCE

• Inspect hardware and assembled parts on a regular basis to insure grill is in safe working condition.

• ALWAYS allow grill to cool completely before handling.

• ALWAYS empty drip tray after use only when ashes have completely cooled.

• Clean grill, including special surfaces such as cooking grates with mild cleaning agents. Wipe outside of grill with damp rag. DO NOT use oven cleaner.

• ALWAYS cover and store cold grill in a protected area.

• Indoor storage of grill is permissible only if the grill is completely cold. Remember to clean drip tray before storing.

• Grill is made of steel and may rust over time. If rusting occurs on outside surfaces, clean area with sand paper or steel wool, then cover with heat resistant paint, except for stainless steel parts.

• If rusting occurs on the inside surface of grill, clean area with sandpaper or steel wool, then coat with cooking oil, except for stainless steel parts.

• NEVER USE PAINT ON INSIDE SURFACES OF GRILL.

damage electric grill.

• To disconnect, turn control panel “OFF” then remove plug from outlet.

• Unplug from outlet when not in use and before cleaning. Allow unit to cool completely before adding/removing grate, or drip tray.

• Dispose of cold ashes by placing them in aluminum foil, soaking with water and discarding in a non-combustible container.

• Do not store electric grill with HOT ashes inside unit. Store only when all surfaces are cold.

• Accessory attachments not supplied by Masterbuilt Manufacturing, Inc. are not recommended and may cause injury.

• The use of accessory attachments not recommended by the appliance manufacturer may cause injuries.

• Never use electric grill for anything other than its intended purpose. This unit is not for commercial use.

• Always use electric grill in accordance with all applicable local, state and federal ﬁ re codes.

• Longer detachable power-supply cords or extension cords are available and may be used if care is exercised in their use.

• If a longer detachable power-supply cord or extension cord is used: 1. The marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of the appliance; and 2. The cord should be arranged so that it will not drape over the counter top or tabletop where it can be pulled by children or tripped over intentionally.

• The extension cord must be a grounding -type 3-wire cord.

• Outdoor extension cords must be used with outdoor use products and are marked with sufﬁ x

ALWAYS MAKE SURE UNIT IS UNPLUGGED AND COOL

TO THE TOUCH BEFORE CLEANING AND STORING.

REMINDER: NEVER OPERATE THIS GRILL UNDER ANY OVERHEAD CONSTRUCTION. MAINTAIN A MINIMUM DISTANCE OF 10 FT (3M) FROM OVERHEAD CONSTRUCTION, WALLS OR RAILS. SEE DIAGRAM BELOW.

Overhead

Construction

Rails

Wall

10 ft (3m)

“W” and with the statement “Suitable for Use with Outdoor Appliances.

• CAUTION - To reduce the risk of electric shock, keep extension cord connection dry and off the

ground.

• Do not clean this product with a water sprayer or the like.

• Keep hands, hair and face away from the element. Be careful of loose hair and clothing

during operation, they could catch fire.

• Never use glassware, plastic or ceramic cookware on this grill.

• Preheating grill is not necessary. If preheating is desired, open lid with caution.

• Minimum distance from side and back of appliance to walls or railing is 24 inches.

• Do not use unit near heat sensitive or combustible structures such as vinyl or wood siding.

WARNINGS & IMPORTANT SAFEGUARDS CONTINUED ON PAGE 3

Page 4

GENERAL WARNINGS AND SAFETY INFORMATION

• Fatty foods (hamburgers,etc.) can have excess grease and cause ﬂ are ups. When cooking fatty foods use a low setting with lid open.

• Clean internal base pan before each use. This will cut down on build-up and ﬂ are-ups.

• Do not expose electric grill to rain. Do not use around water or operate on wet surfaces. This

ASSEMBLY

STEP 20

Insert warming rack (21) onto cooking grate (20), with forks of warming rack straddling grate as shown in FIGURE 3.

could cause an electric shock leading to injury and death.

• Be sure drip tray is clean before each use.

SAVE THESE INSTRUCTIONS

WARNING

COMBUSTION BY-PRODUCT PRODUCED WHEN USING THIS PRODUCT CONTAINS CHEMICALS

KNOWN TO THE STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS,

OTHER REPRODUCTIVE HARM, OR CANCER.

THE MATERIALS USED IN THIS PRODUCT MAY CONTAIN LEAD A CHEMICAL KNOWN TO THE

STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS AND OTHER REPRODUCTIVE HARM.

FIGURE 3

STEP 21

Plug controller (10) into side of grill base (5) from below side shelf

(6), coming in at a slight angle, carefully inserting plug while lifting so that top of controller slips into notch in shelf (6).

Page 5

ASSEMBLY

STOP!

STEP 18

DO NOT RETURN TO RETAILER For Assembly Assistance, Missing or Damaged Parts

Call: MASTERBUILT Customer Service at 1-800-489-1581.

Please have Model Number and Serial Number available when calling.

These numbers are located on silver label on back of unit.

Attach heating element (4) to grill base (5) using screws (A) as shown.

PARTS LIST

(A)

Thumb Screw

STEP 19

14f

14b

Position cooking grate (20) on top of grill base (5).

PART NO QTY DESCRIPTION PART NO QTY DESCRIPTION

1 1 Grill Lid 14b 1 Back Panel

Note: The 2 support bars on cooking grate (20) should span left to right, with the grates going front to back. This alignment is essential for the next step.

2g 1 Temperature Gauge 15 2 Hub Cap 2b 1 Temperature Gauge Base 16 2 Wheel

3 1 Right Side Shelf 17 2 Foot 4 1 Heating Element 18* 2 Leg

5 1 Grill Base 19* 2 Wheel Leg

6 1 Left Side Shelf 20 1 Cooking Grate 7 1 Drip Tray 21 1 Warming Rack 8 1 Drip Tray Bracket 22 2 Seat 91Reﬂ ector Plate 23 1 Right Bottom Hinge

10 1 Controller 24 1 Left Bottom Hinge 11a 2 Front right/Back left Support 25 1 Left Lid Hinge 11b 2 Front left/Back right Support 26 1 Right Lid Hinge

12 1 Bottom Shelf 27 1 Handle

13 2 Side Panel 28 1 Logo Base

14f 1 Front Panel

*Legs are marked with stickers (FR-Front Right, FL-Front Left, BR-Back Right, BL-Back Left) to correspond easily with parts 11a and 11b during assembly Steps 3-5.

Page 6

HARDWARE LIST

ASSEMBLY

STEP 16

Attach left side shelf (6) to both supports (11) using screws (G).

(A)

Thumb Screw

Qty: 2

(E)

M8x55

Phillips Head Screw

Qty:2

(I)

Flat Washer

Qty: 8

(B)

M6x35

Phillips Head Screw

Qty: 2

(F)

Bakelite Spacer

Qty: 2

(J)

Flat Washer

Qty: 5

PARTS LIST

(C)

34x25

Flat Washer

Qty: 4

(G)

M6x13

Phillips Head Screw

Qty: 40

(K)

Flat Washer

Qty: 2

(D)

M4x40

Phillips Head Screw

Qty: 2

(H)

M4x12

Phillips Head Screw

Qty: 3

(L)

M6x8

Phillips Head Screw

Qty: 4

Repeat step on opposite side with right side shelf (3).

GO BACK AND TIGHTEN ALL SCREWS AT THIS TIME.

Note: The left side shelf is the shelf with a square notch in it as seen in FIGURE 1.

NOTCH

FIGURE 1

PART NO REPLACEMENT PART PART NO REPLACEMENT PART

9915110002 Lid Kit - Blue 9915110016 Rear Left Leg Kit

9915110003 Base Kit - Blue 9915110017 Rear Right Leg Kit

9915110004 Lid Handle Kit 9915110018 Front Panel Kit

9915110005 Hinge Kit 9915110019 Back Panel Kit

9915110006 Right Side Shelf Kit 9915110020 Side Panel Kit

9915110007 Left Side Shelf Kit 9915110021 Bottom Shelf Kit

9915110008 Logo Plate Kit 9915110022 Wheel Kit

9915110009 Temperature Gauge Kit 9910090010 Element Kit

9915110010 Drip Tray Kit 9015110002 Foot

9915110011 Grill Seat Kit 9015110003 Warming Rack

9915110012 Front Left/Back Right Leg Kit 9015110004 Cooking Grate

9915110013 Front Right/Back Left Leg Kit 9015110005 Reﬂ ector Plate

9915110014 Front Left Leg Kit 9015110001 Grill Cover

9915110015 Front Right Leg Kit 9007090063 Analog Control w/ Power Cord

9015110006 Hub Cap 9915110023 Lid Kit - Red

9915110024 Lid Kit - Black 9915110025 Base Kit - Red

9915110026 Base Kit - Black 9915110001 Hardware Kit

9815110001 Instruction Manual

STEP 17

Place reﬂ ector plate (9) into bottom of grill base (5).

STOP!

DO NOT RETURN TO RETAILER For Assembly Assistance, Missing or Damaged Parts

Call: MASTERBUILT Customer Service at 1-800-489-1581.

Please have Model Number and Serial Number available when calling.

These numbers are located on silver label on back of unit.

Page 7

ASSEMBLY

STEP 14

*Note: Wing nut is packaged with temperature gauge.

ASSEMBLY

• BEFORE ASSEMBLY READ ALL INSTRUCTIONS CAREFULLY.

• ASSEMBLE UNIT ON A CLEAN, FLAT SURFACE.

• TOOL NEEDED: PHILLIPS HEAD SCREWDRIVER

• UNPACK ALL PARTS AND LAY OUT IN FRONT OF YOU. CHECK TO MAKE SURE ALL PARTS ARE IDENTIFIED AND ACCOUNTED FOR.

FIGURE 2

Attach temperature gauge (2g)

*Note that the front of the grill is actually the shortest width of the bottom storage shelf (12).

and temperature gauge base (2b)

WING NUT

to grill lid (1) using wing nut.

LABELS

FR – Front Right, FL – Front Left,

Tip:

Make sure the temperature

BR – Back Right, BL – Back Left

readings and Masterbuilt logo in the gauge are aligned correctly before tightening down the wing nut.

STEP 15

Place bakelite spacer (F) on grill

lid (1). Attach handle (27) using washers (J) and screws (D) as shown.

FRONT

SHORT SIDE

Make sure lid handle (27) is sloping downward as shown in

FIGURE 2.

ALIGN NOTCH

STEP 1

The bakelite spacers (F) should be angled down and slightly outward with the larger side of

the spacers going to grill lid and the smaller side attached to the handle.

Begin assembly by positioning bottom shelf (12) with the short side of shelf facing you.

This will actually be the front of the grill, making the long sides of shelf the left and right sides.

NOTE: DO NOT FULLY

TIGHTEN ANY SCREWS

UNTIL ALL SCREWS ARE IN

PLACE AND THE GRILL IS

FULLY ASSEMBLED.

STEP 2

Attach wheel (16) to leg (19, “FL”) using washer (K) and screw (E) as shown.

Snap hubcap (15) onto wheel. Repeat step for remaining wheel and wheel leg (19 “BL”).

STEP 3

Align notch on back of foot (17) with the slot in leg (18,”FR”) and insert into leg.

Repeat for remaining leg (18, “BR”) and foot (17).

Page 8

ASSEMBLY

FRONT

SHORT SIDE

STEP 4

Attach bottom shelf (12) to legs (18) using screws (G) with the feet facing away from right side of the shelf as shown.

Repeat for wheel legs (19) on left side using screws (G).

REMEMBER!

The short side of bottom shelf (12) is the front of grill.

STEP 12

Note: Hinge for grill lid is smaller

than hinge for grill base.

From inside grill lid, align holes of left lid hinge (25) to grill lid (1) holes. Secure with screws (G) and ﬂ at washer (C).

Repeat step on other side with right lid hinge (26), washer (C) and screw (G).

14f

STEP 5a

Locate front panel (14f) [This is the short panel without the serial plate] and one side panel (13) [This is one of the longer panels].

Place panel (14f) over (13) while aligning screw holes. Insert screw (G) through both panels, securing panels to front right leg (18, “FR”).

STEP 13

Position grill lid (1) on top of grill base (5), inserting lid hinges (26)

(25) inside bottom hinges (23) (24).

Align holes and secure hinges using screw (B).

Page 9

ASSEMBLY

STEP 10

Place logo base (28) onto grill

base (5). Secure using washers

STEP 5b

Repeat step 5a for leg (19, “FL”).

(J) and screws (H).

14f

STEP 11

STEP 5c

Note: Hinge for grill base is larger than hinge for grill lid.

Attach left bottom hinge (24) to grill base (5) using washers (C)

BL BR

Place panel (14b) [the panel with the serial plate] over panels (13) and insert screw (G); into bottom holes.

14b

and screws (G). [Welded nut on left bottom hinge (24) should be

facing right when secured.]

Repeat step on other side with

right bottom hinge (23), washers

Page 10

ASSEMBLY

STEP 6

Insert support (11b) into front leg (18, “FR”) with holes facing inward. Insert other (11a) into back leg (18, “BR”) with holes facing inward.

Repeat steps for left side.

When all supports are in place screw holes should be facing each other as shown in image.

STEP 8

Attach drip tray bracket (8) to grill base (5) using washers (I) and screws (L).

Note: Make sure to use screw

(L) from the blister pack, and not screw (G) as screw (L) is

shorter than (G).

(L)

M6x8

Phillips Head

Screw

(G)

M6x13

Phillips Head

Screw

STEP 7

Attach seat (22) to supports using screws (G)

Repeat step for remaining seat on opposite side.

STEP 9

Position grill base (5) onto seat

(22) as shown. Secure using washers (I) and screws (G).

View of grill base (5) positioned on seats (22) from below.

Masterbuilt 20150513 Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual