Marmitek MultiMedia Remote Owner's Manual
20021/260203 COPYRIGHT MARMITEK 2003
OWNER’S MANUAL 3
MODE D’EMPLOI 29
GEBRUIKSAANWIJZING 20
BETRIEBSANLEITUNG 11
MultiMedia
Remote
INTRODUCTION
The Marmitek MultiMedia Remote will control most video and audio
equipment. It replaces up to six existing remotes so you just need one
remote to control all of your equipment. On top of that this remote can
also control lights and appliances anywhere in your home when used
with Marmitek X-10 Home Automation Modules. When using the
(optional) Marmitek Powermid receiver, you now can control your
Audio and Video equipment from any room in your house. When
using the (optional) Mouse Remote Receiver, you can even control
your PC. In addition to all these unique features, it is an easy to use
universal remote. It is pre-programmed in the factory for most brands
and models of equipment. Simply enter the code for your equipment
and your remote is ready to use. If you want to add more commands,
the remote is capable of learning the IR commands of almost any
infrared remote control.
HOW TO INSTALL THE BATTERIES
1. Push the tab of the battery compartment on the reverse side of
your remote, and lift the cover.
2. Install four fresh AAA batteries, taking care to match the + and marks in the battery compar tment.
SETTING UP YOUR MARMITEK MULTIMEDIA REMOTE
Button Descriptions:
[1] Indicator light (LED):
The indicator light flashes when the remote is operating.
[2] Power:
Works in the same way as your original remote. Also used to switch
all Marmitek X-10 Lamp Modules on.
[3] Set-up:
Used for entering code numbers matching your TV, VCR or other
equipment.
[4] Learn:
Lets you learn IR commands from an existing remote that might not
be in the Marmitek 8in1 library.
[5] VCR, TV, SAT, DVD, CBL, CD
Used to select the device to control. CBL = Decoder, VCR = Video
[6] PC
In combination with the (optional) Mouse Remote Receiver, pressing
this key allows you to control MP3, DVD and CD functions on your
PC. Ask your dealer for more information or go to www.marmitek.com.
[7] SHIFT
Secondary functions for pre-programmed codes. You may have some
functions on your original Remote, which do not appear on the keypad
of the Marmitek MultiMedia Remote. This does not mean that they are
not available. You may access them via the SHIFT key. If you miss a
function, press the shift button once, and find the function you need
by pressing the buttons. In the Shift mode, the LED is on continuously.
To end the Shift mode press the SHIFT key once more. The SHIFT
key can also be used to learn another function under the same key.
2 3
ENGLISH
2
5
6
7
10
16
17
18
21
1
4
3
9
8
11
12
13
14
15
19
20
23
22
[22] REC:
Record button. Works the same as your original VCR remote. You
must press the REC button twice to begin recording.
[23]
Teletext OFF.
CLEARING THE MEMORY (RECOMMENDED ON FIRST TIME SET-UP):
1. Press and hold SETUP until the LED indicator lights steadily.
Release the SETUP button.
2. Press and release the STOP key twice.
3. Press the MUTE key. The LED will turn off after a few seconds.
4. All code entries and learned command entries are now cleared.
SETTING UP FOR TV, VCR, DECODER, CD, DVD AND SATELLITE
RECEIVER
1. Turn on the device you wish to control (TV, VCR, satellite receiver,
CD etc.).
2. Press and hold SETUP until the LED indicator lights steadily.
Release the SETUP button.
3. Press and release the mode button that matches the device you
want to control (TV, VCR, CD, etc.).
4. Enter the 3 digit code from the Library Code Tables. The LED
turns off after the last digit has been entered.
5. Point the remote at the device and press the POWER button. Your
device should turn off.
6. Turn your device on and press CHANNEL+. If the device
responds, set-up is complete. If some buttons do not operate your
equipment, try one of the other codes for your brand.
FLEXMODE:
It is recommended to program a CD under the CD button, Video
under VCR button, etc. However, except for the TV button, all other
device buttons can be programmed as you wish, i.e. VCR under CD,
SAT under CBL, etc, allowing you to program more than one CD,
VCR, etc.
NOTES:
If your TV, VCR, Satellite Receiver does not respond, try the other
codes for your brand. If it still doesn’t respond, try the Code Search
method.
If the LED blinks rapidly when you enter the code, you may have
entered an invalid code. Recheck the code in the code list and try again.
MANUAL CODE SEARCH:
IMPORTANT:
To select the correct code library section for manual or automat-
ic code search, select a random code from the code list for the
type of device you are looking for (e.g. VCR, SAT, DVD, etc.).
E.g. Auto search for VCR:
1. Press and hold SETUP until the LED indicator lights steadily.
Release the SETUP button
2. Press and release the mode button (VCR, CBL, etc.) you
want to use for controlling your VCR
[8] Showview/V+
This key gives you control over the VideoPlus or ShowView functions
of your VCR (only when your VCR supports this function). When your
VCR does not have this function, this key can give you access to
timer functions or the menu of the VCR.
When using the Showview/V+ key in other modes than VCR (TV,
CBL, SAT, CD), this key usually is used for the SCAN function. This
allows you to zap between channels or listen to the intro’s on a CD.
The key gives a channel up or skip command every 3 seconds. You
can stop the SCAN function by pressing any key. The SCAN functions
stops automatically after 2 minutes.
[9] Marmitek X-10 button:
Lets you control Marmitek X-10 Home Automation Modules to operate
lamps and appliances throughout your home.
0 - 9:
Used as your original remote and to enter device codes.
[10] A · B:
Used for toggle functions (pre-programmed mode).
[11] Ent (Enter):
Used in conjunction with the numeric keys for direct channel tuning. In
set-up mode used to confirm.
[12] Info:
Works in the same way as your original remote.
[13] Channel:
Works like your original remote. Also used to switch Marmitek X-10
Home Automation Modules on and off.
[14] OK/Mute:
Works the same way as your original remote. Also used to switch all
Marmitek X-10 Home Automation Modules off.
[15] Volume:
Works like your original remote. Also used to brighten and dim lights
connected to Marmitek X-10 Lamp Modules.
[16] M1, M2
Macro keys. Lets you execute a pre-programmed string of IR commands.
[17] L1, L2:
Lets you learn additional keys from your original remote.
[18]
Teletext HOLD. Holds the current page.
[19]
Teletext MIX. Mixes the text with the TV program on the background.
[20] Play, FF, Stop, Rew, Pause:
Works the same as on your original remote. Also function as Fast Text
colour keys.
[21]
Teletext ON.
4 5
ENGLISH ENGLISH
IDENTIFYING CODES FOUND USING THE SEARCH
PROCEDURE:
1. Press and hold SETUP until the LED indicator lights steadily.
Release the Set-up button.
2. Press the mode button that matches the equipment you wish to
identify. The LED blinks once.
3. Press and release SETUP. The LED blinks once.
4. To find the first digit, press each number button from 0 to 9 until
the LED blinks. The number you pressed is the first digit of the
code.
5. Press each number button from 0 to 9 as above to find the second digit.
6. Press each number to find the third digit. When the third digit has
been found, the LED will go out. Write down the code you found
on the label inside the battery compartment.
LEARNING
Your Marmitek MultiMedia Remote has the codes for most TV’s,
VCR’s etc. in its code library. However, if the code for your particular
device is not found in the library, you can learn these codes from your
existing remote. Or if you find a code from the tables in this manual
that “almost” matches your device, but a few buttons are missing, you
can learn just those buttons.
LEARNING COMMANDS:
1. Point your existing remote at the Marmitek MultiMedia Remote
(front to front) with a distance of about 2,5 centimetres between
the remotes.
2. Press and hold SETUP until the LED indicator lights steadily.
3. Press the mode button (TV, CD, SAT, etc.) that matches the
equipment you wish to learn. The LED blinks once.
4. Press and release the LEARN button. The LED blinks once.
5. Press and release the button on the Marmitek MultiMedia Remote
that you want to teach. The LED blinks once. (Press SHIFT first to
learn a shifted function).
6. Depending on the type of original remote, you can use choose
one of two methods:
a. Press the button on your original remote that you want to learn.
Hold the button until the LED on the Marmitek MultiMedia Remote
blinks off shortly. When the LED blinks off more than once, you
have to use method b. (note: if you just tried method a, return to
step 5 before choosing method b).
b. Press the button which you want to learn of your original
remote as long as your would do during normal operation of
your device.
7. Repeat steps 5 and 6 for each button you want to learn.
8. When you’re finished learning all the keys, press SETUP.
CLEARING LEARNED COMMANDS TO FREE UP MEMORY:
You can clear learned commands for each device individually (TV,
VCR. Etc.):
1. Press and hold SETUP until the LED indicator lights steadily.
Release the SETUP button.
2. Press the desired mode button (TV, VCR, etc.). The LED flashes once.
3. Press and release the LEARN key twice.
4. Press the SETUP key. The LED will turn off after a few seconds.
5. All learned commands entries under that mode are now cleared.
3. Enter a random 3 digit VCR code from the Library Code
Tables. The LED turns off after the last digit has been entered
4. Now you are able to start the manual or automatic code
search for this mode button
When your device cannot be found in the code list, or your device
doesn’t respond to any of the codes you entered, you can try to find
the code required by using the ‘searching for codes’ method:
1. Turn on the device you want to control.
2. Press and hold SETUP until the LED indicator lights steadily.
Release SETUP button.
3. Press the mode button (TV, VCR, etc.) that matches the equipment you wish to control. The LED blinks once.
4. Press CHANNEL+ repeatedly* until the device to be controlled
changes channel. If you go past the code accidentally press REW
to step back (for the first step push button twice).
5. Press and release the ENTER button to complete the set-up.
*Note: You may have to press CHANNEL+ many times (50+). If the
device does not have a Channel Up function, use the PLAY button
(VCR only) or the POWER button.
AUTOMATIC CODE SEARCH:
IMPORTANT:
To select the correct code library section for manual or automat-
ic code search, select a random code from the code list for the
type of device you are looking for (e.g. VCR, SAT, DVD, etc.).
E.g. Auto search for VCR:
1. Press and hold SETUP until the LED indicator lights steadily.
Release the SETUP button
2. Press and release the mode button (VCR, CBL, etc.) you
want to use for controlling your VCR
3. Enter a random 3 digit VCR code from the Library Code
Tables. The LED turns off after the last digit has been entered
4. Now you are able to start the manual or automatic code
search for this mode button
When searching an unknown code, you can step through the library
automatically (AutoSearch). When your equipment responds, you can
stop the searching process and store the code you found.
1. Turn on the device you want to control.
2. Press and hold SETUP until the LED indicator lights steadily.
Release SETUP button.
3. Press the mode button (TV, VCR, etc.) that matches the equipment you wish to control. The LED blinks once.
5. Press CHANNEL+ once. After a few seconds the remote starts
stepping through the code library (fast search). When the device
responds, you press CHANNEL- to switch to slow search. You can
step back by pressing CHANNEL- (you can step forward by pressing CHANNEL+ in case you went too far back). As soon as the
device responds again, press ENTER to store the code you
found.
6 7
ENGLISH ENGLISH
DELETING COMMANDS UNDER A MACRO KEY
1. Press and hold SETUP until the LED indicator lights steadily.
Release the SETUP button.
2. Press the Macro key you want to delete.
3. Press the SETUP key once more.
CONTROLLING YOUR HOME USING MARMITEK X-10 HOME
AUTOMATION MODULES
The Marmitek MultiMedia Remote allows you to control practically
everything electrical in your home. Besides Infrared technology that
lets you control all your TV, VCR, Cable and Satellite equipment it has
X-10 Radio technology that lets you control lamps and appliances
anywhere in your home remotely.
HERE ARE JUST SOME OF THE THINGS YOU CAN DO WITH
YOUR MARMITEK MULTIMEDIA REMOTE USING THE MARMITEK
X-10 FEATURE:
• Turn on, off or dim lights while watching TV
• Start the coffee machine from your bedroom when you wake up
• Turn on lights at night to scare away intruders if you hear a noise
• Turn on your electric blanket before the movie ends, so it’s nice
and warm to go to bed
To control your lamps and appliances you need Marmitek X-10 Home
Automation Modules, which plug into the existing wall sockets. No
extra wiring is needed. Ask your dealer for more information.
CONTROLLING MARMITEK X-10 MODULES
You can control the Marmitek X-10 Modules as follows:
1. Press and release the Marmitek X-10 button [yellow house].
2.
Use the number buttons to enter the Unit Code number of the chosen
Module (You do not need to enter ‘0’ first for a single digit number).
3. Press the appropriate button for the function you require (see
below).
MARMITEK X-10 FUNCTIONS:
On: CHANNEL +
Off: CHANNEL Bright: VOLUME +
Dim: VOLUME All Lights On: Power
All Units Off: Mute
CHANGING THE X-10 HOUSE CODE
The Marmitek MultiMedia Remote defaults to House Code A, and in
most cases you will not need to change this unless you are experiencing interference form a neighbouring X-10 system.
1. Press and release the Marmitek X-10 button [yellow house]
2. Press and hold SETUP until the LED indicator lights steadily.
Release the SETUP button.
3. Use the number button to enter the number equivalent to the cho-
sen House Code (1=A, 2=B, .... 16=P).
4. Press the ENTER button to confirm the House Code. The LED
turns off.
NOTES FOR LEARNING YOUR REMOTE:
Make sure you have new batteries in both remotes before learning.
Take care not to move either remote while pressing the buttons.
No functions may be stored under the Learn, Setup, TV, VCR, CBL,
SAT, CD, PC, M1, M2, ShowView/V+, X-10 and Enter keys or directly
under the SHIFT key.
Experiment by learning 2 or 3 keys initially (to ensure compatibility)
and then clear the stored learned commands before completely learning your original remote’s keyboard.
When memory is full , the LED will flash for three seconds. It is not
possible to learn any additional keys without clearing a Mode first
(please refer to ‘clearing learned commands to free up memory’)
Experiment with the distance between the remotes if you have a problem learning.
Some remotes do not have their IR sender LED in the centre so you
might need to experiment with the side-to-side position of the remotes
relative to each other.
Avoid direct sunlight, under a fluorescent or incandescent lamp while
teaching the Marmitek MultiMedia Remote.
Use buttons L1 and L2 to learn codes for which the Marmitek
MultiMedia Remote does not have a corresponding button.
If you have problems in learning keys, try clearing the memor y and tr y
learning them again.
HOME THEATRE MACRO FUNCTION
Your MultiMedia Remote has two Macro keys; M1 and M2. You can
program these key to execute a series of commands with one press
of that button. This powerful feature is ideal for switching on all your
audio and video equipment or choose a preferred setting of your
Home Theatre System.
PROGRAMMING THE MACRO KEYS M1 AND M2
1. Press and hold SETUP until the LED indicator lights steadily.
Release the SETUP button.
2. Press the Macro key you want to program
3. Press the keys on your MultiMedia Remote which you want to
store under the Macro key (the maximum is 14 commands). The
order of programming is also the order of execution of the Macro.
4. To store the Macro, press the Macro key once more. When you
have reached the maximum of 14 commands, the Macro programming mode is automatically ended and the 14 commands stored.
NOTE FOR PROGRAMMING MACRO’S:
The Macro keys can execute both Infrared and Radio commands. This
allows you to switch on audio and video equipment and control lights
simultaneously (using optional Marmitek X-10 modules). Ideal for Home
Theatre applications. Go to www.marmitek.com for more information.
8 9
ENGLISH ENGLISH
EINLEITUNG
Mit der Marmitek MultiMedia Fernbedienung können Sie fast alle
Audio- und Videogeräte bedienen.
Die Fernbedienung ersetzt sechs existierende Fernbedienungen so
daß Sie nur eine Fernbedienung benötigen um alle ihre Geräte zu
bedienen. Außerdem hat diese Fernbedienung die möglichkeit von
jedem Ort des Hauses aus Geräte und Lampen zu bedienen, wenn
diese an Marmitek X-10 Home Automation Module angeschlossen
sind. Mit dem Mouse Remote Empfänger (Option) können Sie sogar
Ihren PC bedienen. Wenn ein Marmitek Powermid Empfänger eingesetzt wird, können Sie ebenfalls Ihre Audio- und Videogeräte von
jedem Zimmer im Haus bedienen. Ausser all diesen Möglichkeiten,
können Sie die Fernbedienung einfach als universelle Fernbedienung
verwenden. Die Fernbedienung ist in der Fabrik vorprogrammiert für
die meisten Marken und Modelle. Nach Eingabe des Geräte Codes ist
die Fernbedienung einsatzbereit. Wenn Sie zusätzliche Funktionen
hinzufügen möchten, so ist das möglich. Die Fernbedienung ist fähig
die Funktionen von fast allen Infrarot -Fernbedienungen zu ler nen.
INSTALLATION DER BATTERIEN
1. Öffnen Sie den Batteriefachdeckel auf der Geräteunterseite.
2. Legen Sie vier AAA Batterien ein. Achten Sie dabei auf die
richtige Polarität (+ und - ).
PROGRAMMIERUNG IHRER MARMITEK MULTIMEDIA
FERNBEDIENUNG
Beschreibung der Tasten
[1] LED Anzeige:
Die LED Anzeige blinkt wenn die Fernbedienung aktiv ist.
[2] Power:
Funktioniert wie Ihre Originalfernbedienung. Auch um alle Marmitek
X-10 Lampen Module einzuschalten.
[3] Setup:
Wird benutzt, um den Gerätecode Ihres TV-Gerätes, Videorecorders
oder anderen Geräten einzugeben.
[4] Learn:
Lässt Sie Funktionen einer existierende Fernbedienung lernen, die
nicht in die Marmitek 8in1 Geräte Codeliste anwesend sind.
[5] VCR, TV, SAT, DVD, CBL, CD
Funktionstasten zur Wahl des Gerätes, welches Sie bedienen wollen.
CBL = Decoder, VCR = Video.
[6] PC
Mit dem zusätzlich erhältlichen Mouse Remote Empfänger können
Sie mit Ihrer Fernbedienung auch MP3, DVD und CD-Funktionen
Ihres Computer bedienen. Bei Ihrem Händler erhalten Sie mehr
Information, oder besuchen Sie unsere Website unter www.marmitek.com.
[7] SHIFT
Zusätzlich eingefügte Funktionen bei vorprogrammierten Code. Auf Ihrer
Originalfernbedienung können Funktionen vorhanden sein, die nicht auf
der Tastatur der Marmitek MultiMedia Fernbedienung vorkommen. Dies
bedeutet jedoch nicht, dass diese nicht vorhanden sind. Es ist möglich,
Note: The HouseCode you choose must match the HouseCode on
the Transceiver Module (TM13 or Marmitek Alarm Console) you are
using it with.
CONTROLLING AN IR MINI CONTROLLER (IR7243)
If you already own an IR Mini Controller, you will need to change the
code in the remote to use it. You will find the correct codes for Home
Automation in the Library Code Tables. To change the code:
1. Press and hold SETUP until the LED indicator lights steadily.
Release the SETUP button.
2. Press and release the X-10 button [yellow house].
3. Enter the code you found in the Library Code Tables for Marmitek
X-10 control. The LED turns off after the last digit entered.
CONTROLLING YOUR EQUIPMENT FROM ANY PLACE IN YOUR
HOME
Your remote is prepared to work together with the Marmitek Powermid
Receiver. This receiver allows you to control audio and video equipment from another room or even outside the house, using your
Marmitek MultiMedia Remote. Just plug the receiver into a wall socket
and place it in line of sight with your equipment. Ask your dealer for
more information.
CONTROLLING YOUR PC WITH YOUR MULTIMEDIA REMOTE
Your Marmitek MultiMedia Remote has a number of keys which allow you
to control the DVD, MP3 and CD functions of your PC. You’ll need the
optional Mouse Remote Receiver which connects to a serial port of your
PC. In combination with the BOOM software package, you now can control your DVD, MP3 and CD software with your MultiMedia remote from
another room. Ask your dealer or go to www.marmitek.com for more information.
TROUBLESHOOTING
The remote won’t control your A/V equipment, or doesn’t work at all
• Use manual controls or the original remote control to confirm the
equipment is working properly.
• Be sure you pressed the device key (TV, VCR, etc) for the device
you want to control.
• Try finding the code for your equipment using manual or
automatic code search methods.
• Check that the batteries match the + and - marks.
• Replace the batteries.
10 11
ENGLISH DEUTSCH
[18]
Teletext HOLD. Stellt die aktuelle Seite fest.
[19]
Teletext MIX. Mixt den Text mit dem TV-Programm im Hintergrund.
[20] PLAY, FF, STOP, REW, PAUSE
Arbeiten auf die gleiche Weise wie Ihre Originalfernbedienung.
Arbeiten auch als Teletext Farbtasten.
[21]
Teletext AN.
[22] REC
Aufnahmetaste. Funktioniert auf die gleiche Weise wie Ihre
Originalfernbedienung des Videorecorders. Die REC-Taste muss
zweimal gedrückt werden um die Aufnahme zu starten.
[23]
Teletext AUS.
DEN SPEICHER LÖSCHEN (EMPFOHLEN BEVOR SIE ZUM
ERSTEN MAL EINSTELLEN):
1. Drücken Sie die SETUP Taste bis die LED Anzeige leuchtet.
SETUP Taste wieder loslassen.
2. Drücken Sie zweimal auf die STOP Taste.
3. Drücken Sie auf de MUTE Taste. Die LED Anzeige geht nach
wenigen Sekunden aus.
4. Alle Codeeingaben und gelernte Funktionen sind jetzt gelöscht.
Einstellung der Fernbedienung für Fernseher, Videorecorder, Kabelund SAT-Empfänger und CD- oder DVD-Geräte, usw.
1. Schalten Sie das Gerät das Sie bedienen wollen (Fernseher,
Videorecorder, CD, DVD usw.) ein.
2. Drücken Sie die SETUP Taste bis die LED Anzeige leuchtet.
SETUP Taste wieder loslassen.
3. Drücken Sie die MODE-Taste welche mit dem Gerätetyp übereinstimmet das Sie bedienen möchten (TV, VCR, CD, usw.).
4. Geben Sie den 3 stelligen Code aus der Geräte-Codeliste ein. Die
LED Anzeige geht nach Eingabe der dritten Zahl aus.
5. Richten Sie die Fernbedienung auf dem Gerät zu und drücken Sie
die POWER Taste. Ihre Gerät sollte ausschalten.
6. Schalten Sie das Gerät ein und drücken Sie die CHANNEL+
Taste. Wen das Gerät reagiert, dann ist die Installation vollständig. Falls einige Tasten nicht funktionieren, dann können Sie
eine andere Codenummer ihrer Marke aus der Geräte-Codeliste
versuchen.
FLEXMODUS:
Für TV-Geräte müssen Sie die TV-Taste verwenden. Für die anderen
Geräte aus der Codebibliothek können Sie selbst wählen ob Sie die
VCR, SAT, DVD, CBL oder CD-Taste benutzen. Hierdurch kann die
Fernbedienung auch dazu benutzt werden, für z.B. zwei
Satellitempfänger.
Die erste programmieren Sie dann unter SAT und die zweite z.B.
unter CBL oder DVD.
dass diese Funktionen über die SHIFT-Taste zur Verfügung stehen.
Vermissen Sie eine Funktion, so drücken Sie einmal die Shift-Taste und
suchen die Funktion indem Sie die Tasten drücken. In der Shift-Funktion
brennt die LED-Lampe dauernd. Die Shift-Funktion wird beendet indem
Sie nochmals die Shift-Taste drücken. Die Shift-Taste kann auch benutzt
werden, um eine neue Funktion unter der gleichen Taste einzulernen.
[8] SHOWVIEW / V+
Mit dieser Taste können Sie die ShowVieuw oder VideoPlus
Funktionen Ihres Videorecorders benutzen (wenn Ihr Videorecorder
diese Funktionen besitzt). Wenn Ihr Videorecorder diese Funktionen
nicht hat, dann kann die Taste Zugang zu den Timer-Funktionen oder
zum Menu des Videorecorders geben. Wird die ShowView / V+-Taste
für andere Funktionen benutzt (TV, CBL, SAT, CD), so wird die Taste
oft als Scan-Funktion benutzt. Hiermit können Sie z.B. in der TVEinstellung automatisch zappen zwischen Sendern, oder bei einer CD
das Intro eines Stückes hören. Die Taste sorgt dafür, dass alle 3
Secunden ein Kanal oder eine Nummer hochgeschaltet wird. Sie
beenden die Scan-Funktion, indem Sie eine beliebige Taste drücken.
Die Scan-Funktion wird nach 2 Minuten automatisch beendet.
[9] (Haus-Taste) Marmitek X-10 Taste:
Zur Steuerung von Marmitek X-10 Home Automation Modulen um
damit Lampen und Geräte innerhalb- und ausserhalb des Hauses aus
der Ferne zu steuern.
0 - 9:
Gleiche Funktion wie die original Fernbedienung und für die Eingabe
des Codes.
[10] A · B:
Wird für verschiedene Funktionen (vorprogrammiert) verwendet.
[11] Ent (Enter):
Wird in Verbindung mit der Programmierung oder direkter
Kanaleingabe verwendet. Wird beim Programmieren zur Bestätigung
verwendet.
[12] Info:
Gleiche Funktion wie die Origialfernbedienung.
[13] Channel:
Gleiche Funktion wie die Originalfernbedienung. Wird auch benutzt
um alle Marmitek X-10 Home Automation Module ein- und
auszuschalten.
[14] OK/Mute:
Gleiche Funktion wie die Originalfernbedienung. Wird auch benutzt
um alle Marmitek X-10 Home Automation Module auszuschalten.
[15] Volume:
Gleiche Funktion wie die Óriginalfernbedienung. Wird auch benutzt
um Lampen die an Marmitek X-10 Lampenmodule angeschlossen
sind zu dimmen.
[16] M1, M2
Einstellungstasten. Mit diesen Tasten können mit einem Tastendruck
eine Reihe vorprogrammierter Befehle ausgeführt werden.
[17] L1, L2:
Ermöglicht das Einlernen von anderen Funktionen Ihrer
Originalfernbedienung.
12 13
DEUTSCH DEUTSCH
Loading...