Marantz MM 8077 User Manual

POLSKI

РУССКИЙ

SVENSKA

ESPAÑOL

ITALIANO

FRANÇAISNEDERLANDS

DEUTSCH ENGLISH

7 Channel Power Amplifi er

MM8077

Owner’s Manual

РУССКИЙPOLSKI

ENGLISHDEUTSCHFRANÇAISITALIANOESPAÑOLNEDERLANDSSVENSKA

SAFETY PRECAUTIONS

n

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.

The lightning fl ash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure
that may be of suffi cient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.

IMPOTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings.
Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifi ers)
that produce heat.

9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.

10. Only use attachments/accessories specifi ed by the manufacturer.

11.

Use only with the cart, stand, tripod, bracket, or table specifi ed by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to
avoid injury from tip-over.

12. Unplug this apparatus during lightning storms or when unused for long periods of time.

13. Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.

14. Batteries shall not be exposed to excessive heat such as sunshine, fi re or the like.

n NOTE ON USE / HINWEISE ZUM GEBRAUCH /

OBSERVATIONS RELATIVES A L’UTILISATION

WARNINGS WARNHINWEISE AVERTISSEMENTS

• Avoid high temperatures.
Allow for suffi cient heat dispersion
when installed in a rack.

• Handle the power cord carefully.
Hold the plug when unplugging
the cord.

• Keep the unit free from moisture,
water, and dust.

• Unplug the power cord when not
using the unit for long periods
of time.

• Do not obstruct the ventilation
holes.

• Do not let foreign objects into
the unit.

• Do not let insecticides, benzene,
and thinner come in contact with
the unit.

• Never disassemble or modify the
unit in any way.

• Ventilation should not be impeded
by covering the ventilation
openings with items, such as
newspapers, tablecloths or
curtains.

• Naked fl ame sources such as
lighted candles should not be
placed on the unit.

• Observe and follow local
regulations regarding battery
disposal.

• Do not expose the unit to dripping
or splashing fl uids.

• Do not place objects fi lled with
liquids, such as vases, on the unit.

• Do not handle the mains cord
with wet hands.

• When the switch is in the
OFF (STANDBY) position, the
equipment is not completely
switched off from MAINS.

• The equipment shall be installed
near the power supply so that the
power supply is easily accessible.

• Do not keep the battery in a
place exposed to direct sunlight
or in places with extremely high
temperatures, such as near a
heater.

• Vermeiden Sie hohe Temperaturen.
Beachten Sie, dass eine ausreichende
Belüftung gewährleistet wird, wenn das
Gerät auf ein Regal gestellt wird.

• Gehen Sie vorsichtig mit dem Netzkabel
um.
Halten Sie das Kabel am Stecker, wenn
Sie den Stecker herausziehen.

• Halten Sie das Gerät von Feuchtigkeit,
Wasser und Staub fern.

• Wenn das Gerät längere Zeit nicht
verwendet werden soll, trennen Sie das
Netzkabel vom Netzstecker.

• Decken Sie den Lüftungsbereich nicht ab.

• Lassen Sie keine fremden Gegenstände
in das Gerät kommen.

• Lassen Sie das Gerät nicht mit Insektiziden,
Benzin oder Verdünnungsmitteln in
Berührung kommen.

• Versuchen Sie niemals das Gerät
auseinander zu nehmen oder zu
verändern.

• Die Belüftung sollte auf keinen Fall durch
das Abdecken der Belüftungsöffnungen
durch Gegenstände wie beispielsweise
Zeitungen, Tischtücher, Vorhänge o. Ä.
behindert werden.

• Auf dem Gerät sollten keinerlei direkte
Feuerquellen wie beispielsweise
angezündete Kerzen aufgestellt werden.

• Bitte beachten Sie bei der Entsorgung
der Batterien die örtlich geltenden
Umweltbestimmungen.

• Das Gerät sollte keiner tropfenden oder
spritzenden Flüssigkeit ausgesetzt
werden.

• Auf dem Gerät sollten keine mit
Flüssigkeit gefüllten Behälter wie
beispielsweise Vasen aufgestellt werden.

• Das Netzkabel nicht mit feuchten oder
nassen Händen anfassen.

• Wenn der Schalter ausgeschaltet ist
(OFF (STANDBY)-Position), ist das Gerät
nicht vollständig vom Stromnetz (MAINS)
abgetrennt.

• Das Gerät sollte in der Nähe einer
Netzsteckdose aufgestellt werden, damit
es leicht an das Stromnetz angeschlossen
werden kann.

• Lagern Sie die Batterie nicht an einem
Ort, an dem sie direktem Sonnenlicht oder
extrem hohen Temperaturen ausgesetzt
ist, wie z. B. in der Nähe eines Heizgeräts.

• Eviter des températures élevées.
Tenir compte d’une dispersion
de chaleur suffi sante lors de
l’installation sur une étagère.

• Manipuler le cordon d’alimentation
avec précaution.
Tenir la prise lors du
débranchement du cordon.

• Protéger l’appareil contre
l’humidité, l’eau et la poussière.

• Débrancher le cordon d’alimentation
lorsque l’appareil n’est pas utilisé
pendant de longues périodes.

• Ne pas obstruer les trous
d’aération.

• Ne pas laisser des objets étrangers
dans l’appareil.

• Ne pas mettre en contact des
insecticides, du benzène et un
diluant avec l’appareil.

• Ne jamais démonter ou modifi er
l’appareil d’une manière ou d’une
autre.

• Ne pas recouvrir les orifi ces de
ventilation avec des objets tels que
des journaux, nappes ou rideaux.
Cela entraverait la ventilation.

• Ne jamais placer de fl amme nue
sur l'appareil, notamment des
bougies allumées.

• Veillez à respecter les lois en
vigueur lorsque vous jetez les piles
usagées.

• L’appareil ne doit pas être exposé
à l’eau ou à l’humidité.

• Ne pas poser d’objet contenant du
liquide, par exemple un vase, sur
l’appareil.

• Ne pas manipuler le cordon
d’alimentation avec les mains
mouillées.

• Lorsque l’interrupteur est sur
la position OFF (STANDBY),
l’appareil n’est pas complètement
déconnecté du SECTEUR (MAINS).

• L’appareil sera installé près de la
source d’alimentation, de sorte
que cette dernière soit facilement
accessible.

• Ne placez pas la pile dans un
endroit exposé à la lumière directe
du soleil ou dans des endroits
présentant des températures
extrêmement élevées, par
exemple près d’un radiateur.

I

ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA

РУССКИЙ POLSKI

n NOTE SULL’USO / NOTAS SOBRE EL USO / ALVORENS TE GEBRUIKEN / OBSERVERA ANGÅENDE ANVÄNDNINGEN /

ЗАМЕЧАНИЯ ПО ЭКСПЛУАТАЦИИ / WSKAZÓWKI DOTYCZĄCE OBSŁUGI

AVVERTENZE ADVERTENCIAS WAARSCHUWINGEN VARNINGAR ПРЕДОСТЕРЕЖЕНИЕ OSTRZEŻENIE

• Evitate di esporre l’unità a
temperature elevate.
Assicuratevi che vi sia un’adeguata
dispersione del calore quando
installate l’unità in un mobile per
componenti audio.

• Manneggiate il cavo di alimentazione
con attenzione.
Tenete ferma la spina quando
scollegate il cavo dalla presa.

• Tenete l’unità lontana dall’umidità,
dall’acqua e dalla polvere.

• Scollegate il cavo di alimentazione
quando prevedete di non utilizzare
l’unità per un lungo periodo di tempo.

• Non coprite i fori di ventilazione.

• Non inserite corpi estranei all’interno
dell’unità.

• Assicuratevi che l’unità non entri in
contatto con insetticidi, benzolo o
solventi.

• Non smontate né modifi cate l’unità
in alcun modo.

• Le aperture di ventilazione non
devono essere ostruite coprendole
con oggetti, quali giornali, tovaglie,
tende e così via.

• Non posizionate sull’unità fi amme
libere, come ad esempio candele
accese.

• Prestate attenzione agli aspetti
legati alla tutela dell’ambiente nello
smaltimento delle batterie.

• L’apparecchiatura non deve essere
esposta a gocciolii o spruzzi.

• Non posizionate sull’unità alcun
oggetto contenente liquidi, come ad
esempio i vasi.

• Non toccare il cavo di alimentazione
con le mani bagnate.

• Quando l’interruttore è nella
posizione OFF (STANDBY),
l’apparecchiatura non è
completamente scollegata da
MAINS.

• L’apparecchio va installato
in prossimità della fonte di
alimentazione, in modo che
quest’ultima sia facilmente
accessibile.

• Non tenere la batteria in luoghi
esposti alla luce solare diretta o
con temperature estremamente
elevate, ad esempio in prossimità di
dispositivi di riscaldamento.

• Evite altas temperaturas.
Permite la sufi ciente dispersión del
calor cuando está instalado en la
consola.

• Maneje el cordón de energía con
cuidado.
Sostenga el enchufe cuando
desconecte el cordón de energía.

• Mantenga el equipo libre de
humedad, agua y polvo.

• Desconecte el cordón de energía
cuando no utilice el equipo por
mucho tiempo.

• No obstruya los orifi cios de
ventilación.

• No deje objetos extraños dentro del
equipo.

• No permita el contacto de
insecticidas, gasolina y diluyentes
con el equipo.

• Nunca desarme o modifi que el
equipo de ninguna manera.

• La ventilación no debe quedar
obstruida por haberse cubierto
las aperturas con objetos como
periódicos, manteles o cortinas.

• No deberán colocarse sobre el
aparato fuentes infl amables sin
protección, como velas encendidas.

• A la hora de deshacerse de las pilas,
respete la normativa para el cuidado
del medio ambiente.

• No exponer el aparato al goteo o
salpicaduras cuando se utilice.

• No colocar sobre el aparato objetos
llenos de líquido, como jarros.

• No maneje el cable de alimentación
con las manos mojadas.

• Cuando el interruptor está en
la posición OFF (STANDBY), el
equipo no está completamente
desconectado de la alimentación
MAINS.

• El equipo se instalará cerca de la
fuente de alimentación de manera
que resulte fácil acceder a ella.

• No coloque las pilas en un lugar
expuesto a la luz directa del
sol o donde la temperatura sea
extremadamente alta, como cerca de
una calefacción.

• Vermijd hoge temperaturen.
Zorg er bij installatie in een audiorack
voor, dat de door het toestel
geproduceerde warmte goed kan
worden afgevoerd.

• Hanteer het netsnoer voorzichtig.
Houd het snoer bij de stekker vast
wanneer deze moet worden aan- of
losgekoppeld.

• Laat geen vochtigheid, water of stof
in het apparaat binnendringen.

• Neem altijd het netsnoer uit het
stopkontakt wanneer het apparaat
gedurende een lange periode niet
wordt gebruikt.

• De ventilatieopeningen mogen niet
worden beblokkeerd.

• Laat geen vreemde voorwerpen in
dit apparaat vallen.

• Voorkom dat insecticiden, benzeen
of verfverdunner met dit toestel in
contact komen.

• Dit toestel mag niet gedemonteerd
of aangepast worden.

• De ventilatie mag niet
worden belemmerd door de
ventilatieopeningen af te dekken met
bijvoorbeeld kranten, een tafelkleed
of gordijnen.

• Plaats geen open vlammen,
bijvoorbeeld een brandende kaars,
op het apparaat.

• Houd u steeds aan de
milieuvoorschriften wanneer u
gebruikte batterijen wegdoet.

• Stel het apparaat niet bloot aan
druppels of spatten.

• Plaats geen voorwerpen gevuld met
water, bijvoorbeeld een vaas, op het
apparaat.

• Raak het netsnoer niet met natte
handen aan.

• Als de schakelaar op OFF
(STANDBY) staat, is het apparaat
niet volledig losgekoppeld van de
netspanning (MAINS).

• De apparatuur wordt in de buurt van
het stopcontact geïnstalleerd, zodat
dit altijd gemakkelijk toegankelijk is.

• Bewaar de batterijen niet op een
plaats waar deze blootstaan aan
direct zonlicht of op plaatsen waar
zeer hoge temperaturen heersen,
zoals in de buurt van een kachel.

• Undvik höga temperaturer.
Se till att det fi nns möjlighet till god
värmeavledning vid montering i ett
rack.

• Hantera nätkabeln varsamt.
Håll i kabeln när den kopplas från
el-uttaget.

• Utsätt inte apparaten för fukt, vatten
och damm.

• Koppla loss nätkabeln om apparaten
inte kommer att användas i lång tid.

• Täpp inte till ventilationsöppningarna.

• Se till att främmande föremål inte
tränger in i apparaten.

• Se till att inte insektsmedel på
spraybruk, bensen och thinner
kommer i kontakt med apparatens
hölje.

• Ta inte isär apparaten och försök inte
bygga om den.

• Ventilationen bör inte
förhindras genom att täcka för
ventilationsöppningarna med föremål
såsom tidningar, bordsdukar eller
gardiner.

• Placera inte öppen eld, t.ex. tända
ljus, på apparaten.

• Tänk på miljöaspekterna när du
bortskaffar batterier.

• Apparaten får inte utsättas för
vätska.

• Placera inte föremål fyllda med
vätska, t.ex. vaser, på apparaten.

• Hantera inte nätsladden med våta
händer.

• Även om strömbrytaren står i det
avstängda läget OFF (STANDBY), så
är utrustningen inte helt bortkopplad
från det elektriska nätet (MAINS).

• Utrustningen ska vara installerad
nära strömuttaget så att
strömförsörjningen är lätt att tillgå.

• Förvara inte batteriet på en plats
som utsätts för direkt solljus
eller på platser med extremt
höga temperaturer, som nära ett
värmeelement.

• Избегайте высоких температур.
Учитывайте значительное
распределение тепла при
установке устройства на полку.

• Будьте осторожны при включении/
отключении кабеля питания.
При включении/отключении кабеля
питания беритесь за вилку.

• Не подвергайте
воздействию влаги, воды и пыли.

• Если устройство не будет
использоваться в течение
длительного времени, отключите
кабель питания от сети.

• Не закрывайте вентиляционные
отверстия.

• Следите, чтобы посторонние
предметы не попадали внутрь
устройства.

• Предохраняйте устройство от
воздействия ядохимикатов,
бензина и растворителей.

• Никогда не разбирайте и не
модифицируйте устройство.
Не закрывайте вентиляционные

•

отверстия такими предметами, как
газеты, скатерти, шторы и др.

• Не размещайте на поверхности
аппарата источники открытого
огня, например свечи.

• Обратите внимание на
экологические аспекты утилизации
батарей питания.

• Следите, чтобы на устройство не
проливалась вода.

• Не располагайте емкости, в
которых содержится вода, на
устройстве.

• Не прикасайтесь
мокрыми руками.

• Когда переключатель
находится в положении OFF
(STANDBY), оборудование не
полностью отключено от MAINS

(электрической сети).

• Оборудование следует

устанавливать возле источника
питания, чтобы его можно было
легко подключить.

• Не храните элементы питания в
месте, подверженному прямому
солнечному свету, или в местах
с чрезвычайно высокими
температурами, например, возле
обогревателя.

устройство

к сетевому шнуру

• Unikaj wysokich temperatur.

Jeśli urządzenie jest ustawione
w szafce, należy zapewnić
odpowiednią cyrkulację powietrza.

• Obchodź się ostrożnie z
przewodem zasilającym.
Odłączając przewód z gniazda
elektrycznego, trzymaj zawsze za
wtyczkę.

• Chroń urządzenie przed wilgocią,
wodą i pyłem.

• Odłącz przewód zasilający z sieci,
jeśli urządzenie nie jest używane
przez dłuższy czas.

• Nie zakrywaj otworów
wentylacyjnych.

• Zwróć uwagę, aby do środka
urządzenia nie dostały się żadne
obce przedmioty.

• Chroń urządzenie przed kontaktem
z środkami owadobójczymi,
benzyną oraz rozpuszczalnikiem.

• Nie rozbieraj urządzenia oraz nie
dokonuj w nim żadnych mody

• Nie należy ograniczać wentylacji
urządzenia, np. poprzez zakrycie
otworów wentylacyjnych gazetami,
obrusem, zasłonami itp.

• Na urządzeniu nie wolno stawiać
żadnych źródeł otwartego ognia,
np. zapalonych świec.

• Przestrzegaj lokalnych przepisów
dotyczących utylizacji baterii.

• Chroń urządzenie przez
zachlapaniem lub kapaniem
wszelkich cieczy.

• Nie stawiaj na urządzeniu żadnych
przedmiotów napełnionych wodą,
np. wazonów.

• Nie dotykać przewodu zasilającego
mokrymi rękoma.

• Gdy wyłącznik znajduje się w
położeniu OFF (STANDBY),
urządzenie nie jest całkowicie
odłączone od zasilania.

• Urządzenie należy ustawić w
pobliżu źródła zasilania, aby
zapewnić do niego łatwy dostęp.

• Nie przechowywać baterii na słoń
ani w bardzo ciepłych miejscach,
np. w pobliżu grzejnika.

fi kacji.

cu

II

РУССКИЙPOLSKI

ENGLISHDEUTSCHFRANÇAISITALIANOESPAÑOLNEDERLANDSSVENSKA

Hot surface mark

CAUTION:

HOT SURFACE. DO NOT TOUCH.

The top surface over the internal heat sink may become
hot when operating this product continuously.
Do not touch hot areas, especially around the “Hot
surface mark” and the top panel.

VORSICHT:

HEISSE OBERFLÄCHE.
NICHT ANFASSEN.

Die Oberseite über dem inneren Kühlkörper könnte
heiß werden, wenn dieses Produkt dauerhaft
betrieben wird.
Berühren Sie keine heißen Bereiche, hier besonders
um die Kennzeichnung “Hot surface mark” und die
Oberseite.

PRECAUTION:

SURFACE CHAUDE. NE PAS TOUCHER.

La surface supérieure du dissipateur de chaleur peut
devenir chaude si vous utilisez ce produit en continu.
Ne touchez pas les zones chaudes, tout
particulièrement vers l’inscription “Hot surface
mark” et le panneau supérieur.

ATTENZIONE:

SUPERFICIE CALDA. NON TOCCARE.

La superfi cie superiore al di sopra del dissipatore
interno può riscaldarsi quando si adopera questo
prodotto in maniera continuativa.
Non toccare parti calde, in particolare quelle intorno
alla dicitura “Hot surface mark” e al pannello
superiore.

PRECAUCIÓN:

SUPERFICIE CALIENTE. NO TOCAR.

La superfi cie superior sobre el disipador de calor
interno podría llegar a calentarse al operar este
producto de forma continua.
No toque las áreas calientes, especialmente las
situadas alrededor de la “Hot surface mark” y del
panel superior.

WAARSCHUWING:

HEET OPPERVLAK. NIET AANRAKEN.

Bij ononderbroken bediening van dit product kan het
oppervlak boven de interne koelplaat heet worden.
Raak het toestel niet aan waar het heet is, vooral
niet in de buurt van het “Hot surface mark” en het
bovenpaneel.

FÖRSIKTIHETSMÅTT:

VARM YTA. RÖR EJ.

Ytan ovanför den interna kylfl änsen kan bli varm när
produkten används kontinuerligt.
Rör inte varma områden. Var särskilt försiktig vid
märkningen “Hot surface mark” och på toppanelen.

ОСТОРОЖНО:

ГОРЯЧАЯ ПОВЕРХНОСТЬ.
НЕ ПРИКАСАТЬСЯ.

Поверхность внутреннего теплоотвода может
нагреваться при непрерывной работе устройства.
Не касайтесь “Hot surface mark”, особенно
верхней панели и поверхности вокруг отметки.

UWAGA:

GORĄCA POWIERZCHNIA.
NIE DOTYKAĆ.

Górna powierzchnia nad wewnętrznym radiatorem
może się mocno nagrzać w przypadku długotrwałej
pracy amplitunera.
Nie dotykać gorących powierzchni, szczególnie
wokół symbolu “Hot surface mark” i panelu górnego.

• DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product, to which this declaration relates, is in conformity with the following

standards:
EN60065, EN55013, EN55020, EN61000-3-2 and EN61000-3-3.
Following the provisions of Low Voltage Directive 2006/95/EC and EMC Directive 2004/108/EC, the EC regulation 1275/2008

and its frame work Directive 2009/125/EC for Energy-related Products (ErP).

• ÜBEREINSTIMMUNGSERKLÄRUNG

Wir erklären unter unserer Verantwortung, daß dieses Produkt, auf das sich diese Erklärung bezieht, den folgenden

Standards entspricht:
EN60065, EN55013, EN55020, EN61000-3-2 und EN61000-3-3.
Gemäß den Bestimmungen der Niederspannungsrichtlinie 2006/95/EG und EMV Richtlinie 2004/108/EG, der Verordnung (EG)

Nr. 1275/2008 der Kommission und deren Rahmenrichtlinie 2009/125/EG zu energieverbrauchsrelevanten Produkten (ErP).

• DECLARATION DE CONFORMITE

Nous déclarons sous notre seule responsabilité que l’appareil, auquel se réfère cette déclaration, est conforme aux

standards suivants:
EN60065, EN55013, EN55020, EN61000-3-2 et EN61000-3-3.
Selon la directive 2006/95/EC concernant la basse tension et la directive CEM 2004/108/EC, la réglementation européenne

1275/2008 et la directive 2009/125/EC établissant un cadre de travail applicable aux produits liés à l'énergie (ErP).

• DICHIARAZIONE DI CONFORMITÀ

Dichiariamo con piena responsabilità che questo prodotto, al quale la nostra dichiarazione si riferisce, è conforme alle

seguenti normative:
EN60065, EN55013, EN55020, EN61000-3-2 e EN61000-3-3.
Facendo seguito alle disposizioni della direttiva sul basso voltaggio 2006/95/EC alla direttiva EMC 2004/108/EC, alla norma

EC 1275/2008 e alla relativa legge quadro 2009/125/EC in materia di prodotti alimentati ad energia (ErP).
QUESTO PRODOTTO E’ CONFORME
AL D.M. 28/08/95 N. 548

• DECLARACIÓN DE CONFORMIDAD

Declaramos bajo nuestra exclusiva responsabilidad que este producto al que hace referencia esta declaración, está conforme

con los siguientes estándares:
EN60065, EN55013, EN55020, EN61000-3-2 y EN61000-3-3.

De acuerdo con la directiva sobre baja tensión 2006/95/CE y la directiva sobre CEM 2004/108/CE, la normativa CE 1275/2008

y su directiva marco 2009/125/EC para productos relacionados con la energía (ErP).

• EENVORMIGHEIDSVERKLARING

Wij verklaren uitsluitend op onze verantwoordelijkheid dat dit produkt, waarop deze verklaring betrekking heeft, in

overeenstemming is met de volgende normen:
EN60065, EN55013, EN55020, EN61000-3-2 en EN61000-3-3.

Volgens de voorzieningen van lage spanningsrichtlijn 2006/95/EC en EMC-richtlijn 2004/108/EC, de EU-richtlijn 1275/2008 en

de kaderrichtlijn 2009/125/EC voor energieverbruikende producten (ErP).

• ÖVERENSSTÄMMELSESINTYG

Härmed intygas helt på eget ansvar att denna produkt, vilken detta intyg avser, uppfyller följande standarder:
EN60065, EN55013, EN55020, EN61000-3-2 och EN61000-3-3.

Uppfyller reglerna i lågspänningsdirektivet 2006/95/EC och EMC-direktivet 2004/108/EC, EU-förordningen 1275/2008 och

ramverksdirektivet 2009/125/EC för energirelaterade produkter (ErP).

• СЕРТИФИКАТ СООТВЕТСТВИЯ

Мы гарантируем, что данный продукт, к которому прилагается данный сертификат, соответствует требованиям

следующих стандартов:
EN60065, EN55013, EN55020, EN61000-3-2 и EN61000-3-3.
В соответствии с положениями директивы Директива по низковольтным устройствам 2006/95/EC и директивы EMC

Directive 2004/108/EC, распоряжения ЕС 1275/2008 и директивы 2009/125/EC для энергопотребляющих устройств.

• DEKLARACJA ZGODNOŚCI

Deklarujemy z pełną odpowiedzialnością, że produkt, którego dotyczy niniejsza deklaracja, jest zgodny z następującymi

normami:
EN60065, EN55013, EN55020, EN61000-3-2 oraz EN61000-3-3.
Zgodnie z postanowieniami Dyrektywy niskonapięciowej 2006/95/EC oraz Dyrektywy EMC 2004/108/EC, Regulacji EC

1275/2008 oraz Dyrektywy ramowej 2009/125/EC dotyczącej urządzeń elektrycznych (ErP).

Marantz Europe
A division of D&M Europe B.V. Beemdstraat 11, 5653 MA Eindhoven, The Netherlands

III

ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA

РУССКИЙ POLSKI

CAUTION:

To completely disconnect this product from the mains, disconnect the plug
from the wall socket outlet.
The mains plug is used to completely interrupt the power supply to the unit

and must be within easy access by the user.

VORSICHT:

Um dieses Gerät vollständig von der Stromversorgung abzutrennen, ziehen
Sie bitte den Stecker aus der Wandsteckdose.
Der Netzstecker wird verwendet, um die Stromversorgung zum Gerät völlig

zu unterbrechen; er muss für den Benutzer gut und einfach zu erreichen sein.

PRECAUTION:

Pour déconnecter complètement ce produit du courant secteur, débranchez la
prise de la prise murale.
La prise secteur est utilisée pour couper complètement l’alimentation de

l’appareil et l’utilisateur doit pouvoir y accéder facilement.

ATTENZIONE:

Per scollegare completamente questo prodotto dalla rete di alimentazione
elettrica, scollegare la spina dalla relativa presa a muro.

La spina di rete viene utilizzata per interrompere completamente l’alimentazione
all’unità e deve essere facilmente accessibile all’utente.

PRECAUCIÓN:

Para desconectar completamente este producto de la alimentación eléctrica,
desconecte el enchufe del enchufe de la pared.

El enchufe de la alimentación eléctrica se utiliza para interrumpir por completo
el suministro de alimentación eléctrica a la unidad y debe de encontrarse en un
lugar al que el usuario tenga fácil acceso.

WAARSCHUWING:

Om de voeding van dit product volledig te onderbreken moet de stekker uit
het stopcontact worden getrokken.

De netstekker wordt gebruikt om de stroomtoevoer naar het toestel volledig
te onderbreken en moet voor de gebruiker gemakkelijk bereikbaar zijn.

FÖRSIKTIHETSMÅTT:

Koppla loss stickproppen från eluttaget för att helt skilja produkten från nätet.
Stickproppen används för att helt bryta strömförsörjningen till apparaten, och

den måste vara lättillgänglig för användaren.

ОСТОРОЖНО:

Для того чтобы полностью отключить данный продукт от сети, выньте
штепсельную вилку кабеля питания из розеткиt.
При установке данного продукта убедитесь в том, что используемая
розетка находится в зоне досягаемости.

UWAGA:

W celu całkowitego odłączenia tego urządzenia od zasilania, należy wyjąć
wtyczkę z gniazda elektrycznego.
Przewód zasilający umożliwia całkowite odłączenie dopływu zasilania do
urządzenia i musi być łatwo dostępny dla użytkownika.

A NOTE ABOUT RECYCLING:

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with the local
recycling regulations.
When discarding the unit, comply with local rules or regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with the local regulations concerning battery
disposal.
This product and the supplied accessories, excluding the batteries, constitute the applicable product according to the WEEE
directive.

HINWEIS ZUM RECYCLING:

Das Verpackungsmaterial dieses Produktes ist zum Recyceln geeignet und kann wieder verwendet werden. Bitte entsorgen Sie
alle Materialien entsprechend der örtlichen Recycling-Vorschriften.
Beachten Sie bei der Entsorgung des Gerätes die örtlichen Vorschriften und Bestimmungen.
Die Batterien dürfen nicht in den Hausmüll geworfen oder verbrannt werden; bitte entsorgen Sie die Batterien gemäß der örtlichen
Vorschriften.
Dieses Produkt und das im Lieferumfang enthaltene Zubehör (mit Ausnahme der Batterien!) entsprechen der WEEE-Direktive.

UNE REMARQUE CONCERNANT LE RECYCLAGE:

Les matériaux d’emballage de ce produit sont recyclables et peuvent être réutilisés. Veuillez disposer des matériaux conformément
aux lois sur le recyclage en vigueur.
Lorsque vous mettez cet appareil au rebut, respectez les lois ou réglementations en vigueur.
Les piles ne doivent jamais être jetées ou incinérées, mais mises au rebut conformément aux lois en vigueur sur la mise au rebut
des piles.
Ce produit et les accessoires inclus, à l’exception des piles, sont des produits conformes à la directive DEEE.

NOTA RELATIVA AL RICICLAGGIO:

I materiali di imballaggio di questo prodotto sono riutilizzabili e riciclabili. Smaltire i materiali conformemente alle normative locali sul riciclaggio.
Per lo smaltimento dell’unità, osservare le normative o le leggi locali in vigore.
Non gettare le batterie, né incenerirle, ma smaltirle conformemente alla normativa locale sui rifi uti chimici.
Questo prodotto e gli accessori inclusi nell’imballaggio sono applicabili alla direttiva RAEE, ad eccezione delle batterie.

ACERCA DEL RECICLAJE:

Los materiales de embalaje de este producto son reciclables y se pueden volver a utilizar. Disponga de estos materiales siguiendo los reglamentos
de reciclaje de su localidad.
Cuando se deshaga de la unidad, cumpla con las reglas o reglamentos locales.
Las pilas nunca deberán tirarse ni incinerarse. Deberá disponer de ellas siguiendo los reglamentos de su localidad relacionados con los desperdicios
químicos.
Este producto junto con los accesorios empaquetados es el producto aplicable a la directiva RAEE excepto pilas.

EEN AANTEKENING MET BETREKKING TOT DE RECYCLING:

Het inpakmateriaal van dit product is recycleerbaar en kan opnieuw gebruikt worden. Er wordt verzocht om zich van elk afvalmateriaal te ontdoen
volgens de plaatselijke voorschriften.
Volg voor het wegdoen van de speler de voorschriften voor de verwijdering van wit- en bruingoed op.
Batterijen mogen nooit worden weggegooid of verbrand, maar moeten volgens de plaatselijke voorschriften betreffende chemisch afval worden
verwijderd.
Op dit product en de meegeleverde accessoires, m.u.v. de batterijen is de richtlijn voor afgedankte elektrische en elektronische apparaten (WEEE)
van toepassing.

OBSERVERA ANGÅENDE ÅTERVINNING:

Produktens emballage är återvinningsbart och kan återanvändas. Kassera det enligt lokala återvinningsbestämmelser.
När du kasserar enheten ska du göra det i överensstämmelse med lokala regler och bestämmelser.
Batterier får absolut inte kastas i soporna eller brännas. Kassera dem enligt lokala bestämmelser för kemiskt avfall.
Denna apparat och de tillbehör som levereras med den uppfyller gällande WEEE-direktiv, med undantag av batterierna.

ПРИМЕЧАНИЕ О ПЕРЕРАБОТКЕ:

Упаковочный материал данного продукта может быть переработан и повторно использован. Пожалуйста, сортируйте материалы в
соответствии с местными требованиями переработки.
При утилизации определенных блоков соблюдайте местные правила утилизации.
Не выбрасывайте и не сжигайте батарейки, соблюдайте местные правила утилизации химических отходов.
Данный продукт и аксессуары в упаковке соответствуют директиве WEEE, исключая батарейки.

INFORMACJE DOTYCZĄCE RECYKLINGU:

Opakowanie urządzenia zostało wykonane z materiałów nadających się do wtórnego przetworzenia. Utylizację wszelkich materiałów należy
przeprowadzić zgodnie z obowiązującymi lokalnymi przepisami dotyczącymi recyklingu.
Urządzenie należy zutylizować zgodnie z lokalnymi przepisami.
Baterii nie wolno wyrzucać do śmieci lub palić. Należy je zutylizować zgodnie z obowiązującymi zasadami dotyczącymi utylizacji baterii.
Niniejszy produkt oraz dostarczone wraz z nim akcesoria (oprócz baterii) stanowią właściwy produkt, zgodnie z dyrektywą WEEE.

IV

РУССКИЙPOLSKI

n Cautions on installation / Vorsichtshinweise zur aufstellung /

Précautions d’installation / Precauzioni sull’installazione /
Emplazamiento de la instalación / Voorzorgsmaatregelen bij de installatie /
Försiktighet vid installationen / Меры предосторожности при установке /

Uwagi dotyczące instalacji

Wall
Wand
Paroi

z

z

zz

z For proper heat dispersal, do not install this unit in a confi ned space, such as a bookcase or similar enclosure.

• More than 0.3 m is recommended.

• Do not place any other equipment on this unit.

z Stellen Sie das Gerät nicht an einem geschlossenen Ort, wie in einem Bücherregal oder einer ähnlichen

Einrichtung auf, da dies eine ausreichende Belüftung des Geräts behindern könnte.

• Empfohlen wird über 0,3 m.

• Keine anderen Gegenstände auf das Gerät stellen.

z Pour permettre la dissipation de chaleur requise, n’installez pas cette unité dans un espace confi né tel qu’une

bibliothèque ou un endroit similaire.

• Une distance de plus de 0,3 m est recommandée.

• Ne placez aucun matériel sur cet appareil.

z Per una dispersione adeguata del calore, non installare questa apparecchiatura in uno spazio ristretto, come ad

esempio una libreria o simili.

• Si raccomanda una distanza superiore ai 0,3 m.

• Non posizionare alcun altro oggetto o dispositivo su questo dispositivo.

z Para la dispersión del calor adecuadamente, no instale este equipo en un lugar confi nado tal como una librería

o unidad similar.

• Se recomienda dejar más de 0,3 m alrededor.

• No coloque ningún otro equipo sobre la unidad.

z Plaats dit toestel niet in een kleine afgesloten ruimte, zoals een boekenkast e.d., omdat anders de warmte niet

op gepaste wijze kan worden afgevoerd.

• Meer dan 0,3 m is aanbevolen.

• Plaats geen andere apparatuur op het toestel.

z För att tillförsäkra god värmeavledning får utrustningen inte installeras i instängda utrymmen, som t.ex. en

bokhylla eller liknande.

• Mer än 0,3 m rekommenderas.

• Placera ingen annan utrustning ovanpå den här enheten.

z Чтобы не препятствовать отводу тепла, не устанавливайте блок в закрытое ограниченное пространство,

например, в книжный шкаф и т.п.

• Рекомендуемое расстояние - не менее 0,3 м.

• Не размещайте какое-либо другое оборудование на этом модуле.

z Ze względu na prawidłowe odprowadzanie ciepła, należy pamiętać o zachowaniu odpowiedniej przestrzeni

wokół urządzenia. Nie należy umieszczać urządzenia w zamkniętych szafkach lub podobnych ograniczonych
przestrzeniach.

• Zalecane jest zachowanie odległości powyżej 0,3 metra.

• Nie należy stawiać na tym urządzeniu żadnego innego sprzętu.

Parete
Pared
Muur
Vägg

Стена
Ściana

ENGLISHDEUTSCHFRANÇAISITALIANOESPAÑOLNEDERLANDSSVENSKA

V

ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA

РУССКИЙ POLSKI

Усилитель

Marantz MM8077

(РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ)

Вы приобрели усилитель мощности производства компании “D&M Холдингс Инк”, Япония (“D & M Holdings Inc.”, Japan). Модель MM8077 является многоканальным
усилителем и предназначена для многоканального усиления звука в домашних аудиосистемах. Это изделие широко известно в кругах истинных ценителей
высококлассного звука. Качество и безопасность подтверждены множеством тестов, проведенных как зарубежными, так и российскими испытательными
лабораториями.

Изготовитель в течение 3 лет (срок службы) после выпуска данного изделия обеспечивает наличие комплектующих в целях возможности проведения ремонта
и технического обслуживания, по истечении которого эксплуатация и техническое обслуживание продолжается в соответствии с действующими нормативными
документами. Изделие остается безопасным для жизни, здоровья человека и окружающей среды в течение всего срока эксплуатации. Гарантийный срок - 1 год.

Информация о Российской сертификации

No сертификата

соответствия

РОСС JP.АГ83.B02602 Крафт ГОСТ Р МЭК 60065-2009

См. в конце инструкции

ВНИМАНИЕ: Если Вы приобрели аудиоаппаратуру надлежащего качества, то, по Российским законам, она не подлежит возврату или обмену на аналогичный товар других
размера, формы и т.д.

Орган по

сертификации

Нормативные документы

ГОСТ 5651-89
ГОСТ Р 51515-99
ГОСТ 22505-97
ГОСТ Р 51317.3.2-2006
ГОСТ Р 51317.3.3-2008

Основные технические характеристики

Наименование

сертифицированной продукции

Устройства усилительные/
преобразовательные

Срок действия

сертификата

До 16.05.2013

D&M Холдингс Инк

Здание D&M, 2-1 Ниссин-тё

Кавасаки-ку, Кавасаки-си, Канагава

2108569, Япония

D&M Holdings Inc.

D&M Building, 2-1 Nisshin-Cho

Kawasaki-Ku, Kawasaki-Shi, Kanagawa

2108569, Japan

VI

Getting started

ENGLISH

Getting started

Thank you for purchasing this marantz product. To ensure proper
operation, please read this user guide carefully before using the
product.
After reading them, be sure to keep them for future reference.

Contents

Getting started ···············································································1

Accessories ··················································································1
About this manual ·········································································1
Features ························································································ 2
Cautions on handling ····································································2

Part names ······················································································3

Front panel ····················································································3
Rear panel ·····················································································3

Connections ····················································································4

Preparations ·················································································· 4
Speaker connections ····································································4
Example connection variation ······················································· 5
Connecting MM8077 with an AV pre-tuner (AV8801) ··················6
Connecting the power cord ··························································7
Remote control connection ··························································7
Connection to an external control device ·····································8

Operations ······················································································9

Turning the power on ···································································9
Turning the power standby ···························································9
Switching the illumination lamp ON/OFF ······································9
Setting the power to standby automatically
(Auto standby function) ································································9

Accessories

Check that the following parts are supplied with the product.

q Owner’s Manual ...................................................................... 1

w Power cord .............................................................................. 1

e Remote control cable ..............................................................1

we

About this manual

n Symbols

v

NOTE

n Illustrations

Note that the illustrations in these instructions are for explanation
purposes and may differ from the actual unit.

This symbol indicates a reference page on which
related information is described.

This symbol indicates a supplementary information
and tips for operations.

This symbol indicates a supplementary information
and tips for operations.

Part names Connections Operations Explanation of terms Troubleshooting Specifi cations Index

Explanation of terms ···································································10

Troubleshooting ···········································································10

Specifi cations ···············································································11

Index ······························································································11

1

ENGLISH

Features

Current feedback discrete power amp

This is equipped with a current feedback power amp that uses the
complimentary push-pull circuit used in the marantz Hi-Fi power
amp. This amp provides increased operating stability, and high­speed, wide ranging high-density playback.
The current/voltage conversion amplifi cation section in the latter
part of the power amp is equipped with a Wilson current mirror
circuit that amplifi es to the high sound range with low distortion.

Improved instant power supply capability

The fi nal stage of the power amp is equipped with the same LAPT
(high effi ciency power transistor) that is installed in the marantz
Hi-Fi power amp, providing improved instant power supply
capability.
The power section is equipped with a large-sized transformer.
As one of the essential parts of the power section, this unit
is equipped with marantz original 50,000 μF / 71 V×2 block
condensers, which have been repeatedly tested for sound quality.
These improvements to the power supply capability provide a
powerful, presence-fi lled sound.

High sound quality design based on pure surround
philosophy

Equipped with a chimney-shaped heat sink to effi ciently process
the heat emitted from each channel amp , and exceptionally quiet
cooling fans. A high-sensitivity temperature sensor IC is used to
control the cooling fans, adjusting the rotation speed to match the
amount of heat generated by the amp.
These components provide the sound quality and low-noise you
would expect at a high-end theater.
In addition, this unit is designed for superb quality sound, and is
equipped with high quality components such as a high-end audio
condenser and fi lm condenser throughout.

BALANCED/UNBALANCED selecting function

Depending on the desired use, input for each channel can be
selected between BALANCED input and UNBALANCED input.

Remote Power Control

This unit is equipped with a remote power control function. When
a marantz AV Pretuner AV8801 or AV7701 is connected to this
unit, this unit’s power can be switched ON/OFF together with the
AV8801 or AV7701 power supply.
Connection to the AV8801 or AV7701 is a ground fl oating
connection that prevents negative infl uences on sound quality as
far as possible.

Other Functions

Equipped with IR fl ash input that supports custom installations,
and DC trigger input and output terminals.

Cautions on handling

• Before turning the power switch on

Check once again that all connections are correct and that there are
no problems with the connection cables.

• Power is supplied to some of the circuitry even when the unit is
set to the standby mode. When going on vacation or leaving home
for long periods of time, be sure to unplug the power cord from the
power outlet.

• About condensation
If there is a major difference in temperature between the inside of
the unit and the surroundings, condensation (dew) may form on
the operating parts inside the unit, causing the unit not to operate
properly.
If this happens, let the unit sit for an hour or two with the power
turned off and wait until there is little difference in temperature
before using the unit.

• Cautions on using mobile phones
Using a mobile phone near this unit may result in noise. If that
occurs, move the mobile phone away from this unit when it is in use.

• Moving the unit
Turn off the power and unplug the power cord from the power
outlet. Next, disconnect the connection cables to other system units
before moving the unit.

• About Care

• Wipe the cabinet and control panel clean with a soft cloth.

• Follow the instructions when using a chemical cleaner.

• Benzene, paint thinner or other organic solvents as well as

insecticide may cause material changes and discoloration if brought
into contact with the unit, and should therefore not be used.

2

Part names

ENGLISH

Front panel

For buttons not explained here, see the page indicated in parentheses ( ).

q uwrte y

q Power operation button

(ON/STANDBY) ············································ (9)

w STANDBY indicator ······································ (9)
e Illumination lamp ·········································(9)
r Protection indicator (PROTECT) ············(9, 10)
t Auto power off indicator (A.P.OFF) ············ (9)
y Power indicator ············································(9)

u DISPLAY button ············································ (9)

• Press this button to turn the illumination lamp
ON/OFF.

• You can set the auto standby function by
pressing and holding this button for more than
5 seconds.

Rear panel

See the page indicated in parentheses ( ).

w e r iuytq

q RCA input connectors (UNBALANCED) ·····(6)
w Input selector ················································ (4)
e XLR input connectors (BALANCED) ···········(6)
r Speaker terminals

(SPEAKER SYSTEMS) ·································· (6)

Part namesGetting started

Connections Operations Explanation of terms Troubleshooting Specifi cations Index

t FLASHER IN jack ···········································(8)
y DC CONTROL jacks ······································(8)
u AC inlet (AC IN) ·············································(7)
i REMOTE CONTROL connectors ·············· (7, 8)

3

ENGLISH

ew q

Connections

NOTE

• Do not plug in the power cord until all connections have been completed.

• When making connections, also refer to the operating instructions of the other components being
connected.

• Check the channel, and then connect correctly.

• Do not bundle power cords together with connection cables. Doing so can result in noise.

Preparations

Cables used for connections

Prepare the correct cables for use with the additional devices.

Audio cables

Balanced connections (XLR)

Balanced cable



Unbalanced connections (RCA)

Audio cable

Speaker connections

Speaker cable

n XLR connector PIN arrangement

The PIN arrangement in this device uses the European method.
In the USA method, w is COLD, and e is HOT.
When connecting a device that utilizes the USA type of PIN arrangement, replace
the w and e plugs on one side of the balanced cable.

NOTE

Do not short the HOT and GND or COLD and GND for use.

q GND (Ground)
w HOT (Hot)
e COLD (Cold)

Speaker connections

Carefully check the channels of the speakers to be
connected to this unit (L/R/SL/SR/SBL/SBR/C) and
+ (red), – (black), and connect like poles together.

Connecting the speaker cables

Peel off about 10 mm of sheathing from the tip
of the speaker cable, then either twist the core
wire tightly or terminate it.

NOTE

• Connect so that the speaker cable core wires
do not protrude from the speaker terminal.
The protection circuit may be activated if the
core wires touch the rear panel or if the + and –
sides touch each other (vpage10 “Protection
circuit”).

• Never touch the speaker terminals while the
power supply is connected. Doing so could
result in electric shock.

• Use speakers with impedance of 6 to 8 Ω.

Sets the connected input connectors

Switches the input settings used for input to each channel.

BALANCED: Set when connected to the XLR connector.
UNBALANCED: Set when connected to the RCA connector.

NOTE

If audio is input into input connectors that are not set using the input switching
switch, the audio will not be output from the speakers.

4

Example connection variation

ENGLISH

n Connection to an AV pre-tuner

AV8801 MM8077

PURE DIRECT

M-DAX

DINAMIC EQ/VOL

DSX

SURROUND
MODE

DISPLAY

AUTO

STATUS

SW

ENTER

RETURN

MENU

ZONE 2

ZONE 2

ZONE

SPKR A/B

BAND

HDMI OUT

ON/OFF

ON/OFF

SELECT

SLEEP

MM8077 MM8077 or MM7055

MM8077 MM8077 or MM7055

[Speakers]

FL

FR SL SR SBL SBRC

FL FR SL SR SBL SBRC

FHL FHR

FWL FWR

FL FR SL SR SBL SBRC

FHL FHR Z2 Z2

or or

FWL FWR

Z3 Z3

7.1ch surround playback

11.1ch surround playback

9.1ch surround playback
+

ZONE2 playback

or

ZONE3 playback

Part namesGetting started Operations Explanation of terms Troubleshooting Specifi cations Index

Connections

FL Front speaker (L) C Center speaker SL Surround speaker (L) SBL Surround back speaker (L) FHL Front height speaker (L)

FR Front speaker (R) SW Subwoofer SR Surround speaker (R) SBR Surround back speaker (R) FHR Front height speaker (R)

FWL Front wide speaker (L) FWR Front wide speaker (R) Z2 Zone2 speaker Z3 Zone3 speaker

5

ENGLISH

BALANCED

UNBALANCED

BALANCED

UNBALANCED

Connecting MM8077 with an AV pre-tuner (AV8801)

The illustrations below show connection examples for performing 7.1-channel surround playback using the
MM8077 and AV pre-tuner (AV8801).

• For settings and operating procedures of the AV8801, see the AV8801 owner’s manual.

• When connecting the AV8801, be sure to also consult the AV8801 owner’s manual.

Balanced connections
(when connecting to the XLR input connectors)

AV pre-tuner AV8801

Unbalanced connections
(when connecting to the RCA input connectors)

AV pre-tuner AV8801

(SL)

(FL)

(C)

wqwq wqwq

(SBL) (SBR)

wq wq

(FR)

(SR)

MM8077

(FL)

(SL)

(C)

wqwq wqwq

(SBL) (SBR)

wq wq

(FR)

(SR)

MM8077

6

ENGLISH

Connecting the power cord

Wait until all connections have been completed before connecting the power cord.

To household power outlet

(AC 230 V, 50/60 Hz)

Power cord

(supplied)

NOTE

• Insert the plugs securely. Loose connections will result in the generation of noise.

• During power standby, a minimal amount of power is consumed. To totally cut off the power, remove
the power cord from the power outlet.

Remote control connection

When connecting a marantz AV8801 AV pre-tuner, you can switch the power of this unit to ON/STANDBY
together with the AV8801 power supply.
For details, see the AV8801 owner’s manual.

AV pre-tuner AV8801

Part namesGetting started Operations Explanation of terms Troubleshooting Specifi cations Index

Connections

MM8077

7

ENGLISH

Connection to an external control device

qw re

q Flasher input connector (FLASHER IN)

Used when connecting a control box or other
control device to this unit, and using such a
device to control this unit.

wDC control output connector

(DC CONTROL OUT)

Used when connecting a device that has a DC
control input terminal to this unit, and linking
the power ON/STANDBY function of this device
with the power ON/STANDBY of the connected
device.
An electrical signal of max 12 V/44 mA is output
from the DC control output terminal.
For details, see the instruction manual of the
connected device.

NOTE

• Do not use the DC control output terminal as
the power supply for an external device.

• When using this unit with a device connected
to the DC control connector, set the auto
standby function to “Off” (vpage 9
“Setting the power to standby automatically
(Auto standby function)”).

eDC control input connector

(DC CONTROL IN)

Used when connecting a unit that has a DC
control input terminal to this device, and linking
the power ON/STANDBY of the connected
device with the power ON/STANDBY of this
unit.
For details, see the instruction manual of the
connected device.

NOTE

• When a 5 V – 15 V voltage is input to the DC
control input terminal, the power of this unit
switches ON.
However, inputting voltage outside of this
range will cause damage to this unit.

• When using this unit with a device connected
to the DC control connector, set the auto
standby function to “Off” (vpage 9
“Setting the power to standby automatically
(Auto standby function)”).

rRemote control connector

Used when connecting an external control
device to this unit, and using the device to
control this unit.

NOTE

When connecting a marantz AV8801 or AV7701
AV pre-tuner, you can switch the power of this
unit to ON/STANDBY together with the AV8801/
AV7701 power supply.
For details, see the AV8801 or AV7701 owner’s
manual.

8

Operations

ENGLISH

STANDBY
indicator

Protection
indicator

DISPLAYON/STANDBY

Power
indicator

Turning the power on

When the power is in standby, press ON/STANDBY.

• The protection indicator fl ashes for approximately 7 seconds, and
the power switches on.

• The power indicator lights.

NOTE

When turning the power ON, turn the volume control of connected
devices down to the minimum.

Turning the power standby

When the power is in power on, press ON/STANDBY.

The STANDBY indicator lights, and the power changes to standby.

NOTE

Even if the unit is switched to standby, some of the circuits are still
active. If you will not be using this unit for a prolonged period (due to a
holiday etc), remove the power plug from the wall socket.
Furthermore, to prevent unexpected accidents, make sure the power
plug is located where it can be removed at any time.

Switching the illumination lamp
ON/OFF

If the unit is being used with the factory settings, the illumination lamp
lights.
You can turn the illumination lamp off if it is making the room too
bright at nighttime.

Press DISPLAY.

Each time this button is pressed, the illumination lamp turns ON/
OFF.

Setting the power to standby
automatically
( Auto standby function)

When the auto standby function is set to ON, if there are no signals
input into this unit and no operations are performed for more than 30
minutes, the power of this unit automatically switches to standby.

• The factory setting is “ON”.

Press DISPLAY for more than 5 seconds.

The auto power off display switches as shown below according to
the auto standby function.

• When the auto standby function is ON: Lit

• When the auto standby function is OFF: Off

Part namesGetting started Explanation of terms Troubleshooting Specifi cations Index

OperationsConnections

NOTE

When performing the “Setup Assistant” or “Speaker Setup” function
on AV7701 or AV8801 that is used together with this unit, set the auto
standby function to “Off” on this unit.

9

ENGLISH

Explanation of terms

P

Protection circuit

This is a function to prevent damage to components within the power
supply when an abnormality such as an overload or excess voltage
occurs for any reason.
In this unit, the STANDBY indicator and protection indicator blinks and
the unit enters standby mode when an abnormality occurs.

S

Speaker impedance
This is certain-rated resistance of the speaker set to an alternating
current and expressed in ohms.
The smaller the impedance, the greater the output.
However, load on the amplifi er is increased. Use speakers whose
impedance is supported by this unit.

Troubleshooting

If a problem should arise, fi rst check the following:

1. Are the connections correct?

2. Is the set being operated as described in the user guide?

3. Are the other components operating properly?

If this unit does not operate properly, check the items listed in the table below. Should the problem persist, there may be a malfunction.
In this case, disconnect the power immediately and contact your store of purchase.

Symptom Cause/Solution Page

The power does not switch on.
Or, the power switches off immediately after
being switched on.

There is no sound from the speakers. • Check the speaker connections and connections to the other devices.

The power suddenly switches off during use,
and the STANDBY indicator and protection
indicator fl ash at approximately 0.5 second
intervals.

When the power switches off suddenly
during use, the STANDBY indicator fl ash
at approximately 0.1 second intervals and
protection indicator fl ash at approximately 0.5
second intervals.

• Check that the power plug is inserted correctly in the wall socket.

• The protective circuit has operated. In this case, remove the power plug
from the wall socket, and wait for at least 1 minute before inserting it in the
wall socket again.

• Alter the input selector to match the input connector (BALANCED or
UNBALANCED) of the connected device.

• The internal temperature of the unit has increased, causing the protective
circuit to operate. Remove the power plug from the wall socket, wait until
the temperature of the unit has dropped adequately, and then insert the
power plug back into the wall socket.

• Install this unit in a well-ventilated location.

• Use speakers that have the specifi ed impedance.

• If the two core wires of the speaker cables are touching, or if a core wire
is out of the terminal causing the core wire to touch the rear panel of this
unit, the protective circuit will operate. Remove the power plug from the
wall socket, and fi rmly re-insert the core wire, or fi x the terminal before
reconnecting it.

• Turn the volume down on the amp connected to this unit, and insert the
power plug again.

• The protective circuit has operated. In this case, remove the power plug
from the wall socket, re-examine the installation conditions of this unit, and
check the speaker cable connections. If the same situation occurs when the
power is switched on again, contact the marantz Service Center.

7

7, 10

6
4

–

–
4

4, 10

–

6,7,10

10

ENGLISH

Specifi cations

Rated power output
(from 20 Hz to 20 kHz/THD = 0.08 %, two channels driven): 150 W/ch, 8 Ω

Maximum effective output power
(from 1 kHz, 6 Ω, 10% two channels driven): 210 W/ch, 6 Ω

Output connectors: 6 – 8 Ω
Frequency response (1 W, 8 Ω): 8 Hz – 100 kHz (±3 dB)
Damping factor: 100
Input sensitivity/impedance: 1.2 V / 22 kΩ (UNBALANCED)

Signal-to-noise ratio (IHF-A): 105 dB
Voltage amplifi cation level: 29 dB
Supply voltage: AC 230 V, 50/60 Hz
Power consumption: 880 W
Standby power: 0.4 W

For purposes of improvement, specifi cations and design are subject to change without notice.

180 W/ch, 6 Ω

2.4 V / 30 kΩ (BALANCED)

Index

v Numerics

7.1ch surround playback ······································ 5

9.1ch surround playback ······································ 5

11.1ch surround playback ···································· 5

v A

Accessories ·························································· 1
Audio cable ··························································· 4
Auto standby function ··········································9

v B

Balanced cable ·····················································4

v C

Condensation ······················································· 2
Connection

Balanced ···························································· 6
External control device ······································8
Power cord ························································7
Remote control ·················································· 7
Unbalanced ························································ 6

v E

Example connection variation ······························ 5

v F

Front panel ···························································3

v T

Troubleshooting ················································· 10
Turning the Power On ·········································· 9
Turning the power standby ··································9

v X

XLR connector PIN arrangement ························· 4

v Z

ZONE2 ·································································· 5
ZONE3 ·································································· 5

Part namesGetting started Connections Operations

Explanation of terms IndexSpecifi cationsTroubleshooting

v P

Protection circuit ················································10

v R

Rear panel ····························································3

v S

Sets the connected input connectors ··················4
Speaker cable ······················································· 4
Speaker impedance ············································ 10
Switching the illumination lamp ON/OFF ·············9

11

Dimensions / Abmessungen / Dimensions / Dimensioni / Dimensions / Dimensies / Mått / Размеры / Wymiary

Unit / Einheit / Unité / Unità / Unidad / Eenheid / Enhet / Единицы измерения / Jednostka : mm

21.5

360.0

383.5

267.0

55.5 39.5

2.0

440.0

170.5

185.0

50.0

340.0

56.0

50.0

14.5

Weight / Gewicht / Poids / Peso / Peso / Gewicht / Vikt / Вес / Waga : 18.0 kg

V00

Printed in China 5411 10986 00AM

D&M Holdings Inc.