Makita BUR360Z, UR360DZ, UR360DWB, UR360DWBE, BUR360ZX2C Technical Information
...
Optional accessories
Nylon cutting head, Charger DC36WA/DC36RA, Battery BL3622A/BL3626, Battery converter BCV02
Standard equipment
Note: The standard equipment for the tool shown above may vary by country.
Nylon cutting head (Bump & Feed 4)..... 1
Hex wrench (for M4) .............................. 1
Socket wrench ........................................ 1
Pin 4 (Lock key) ..................................... 1
Models No.
Description
CONCEPT AND MAIN APPLICATIONS
BUR360 (HRU01*1), UR360D
Cordless String Trimmer 300mm (11-3/4
")
Models BUR360 is a cordless string trimmer 300mm(11-3/4") with a bent shaft,
powered by 36V/2.6Ah Li-ion battery BL3626, and charged by DC36RA.
The main advantages are "Environment-friendly" and "Light weight and
compact size" obtained by using Zero exhaust emission Li-ion battery and
Brushless DC motor as the power unit instead of gasoline and engine.
Other advantages are:
• Grass clipping removal function
• High/Low 2-speed selection with variable speed in each range
Model BUR360 is available in the following variations, like UR360D.
Specification
80/ 94
300
36
Standard cutting tool/ Spindle thread size
Battery
Max output: W
Voltage: V
2.2/ 2.6Capacity: Ah
Li-ion
Specifications
Model
Cell
Electric brake Yes
Overload protection Current limiter
*
1 No load speed of the cutting tool *2 with Nylon cutting head
Nylon cutting head/ M8 Right-handed
BUR360
5.1 (11.2)
No load speed*
1: min.-1 = rpm
60(with DC36WA) / 22(with DC36RA)Charging time (approx.): min.
Energy capacity: Wh
High
Low
0 - 7,000
0 - 5,100
Model No. Offered to
type quantity
Charger
Battery
converter
Battery
Battery
cover
BUR360Z
UR360DZ
BUR360RD
BUR360RDE
UR360DWB
UR360DWBE
BUR360ZX2C
HRU01Z
HRU011
HRU01
HRU01C1
HRU01C
HRU01ZX2
No
1
BL3626
BL3622A
BL3622A
2
1
2
No
No
No
No
No
No
No
No
No
No NoNo
1
1
DC36RA
DC36WA
1
2
No
1
DC36WA
No
No
No
BCV02
BCV02
All countries except North and
Central American countries
The models also includes the accessories listed below in "Standard equipment".
1
BL3626
2
No
1
DC36RA
Variable speed control Yes
Soft start Yes
Reversing switch Yes
L
295 (11-5/8)Width (W)
Height (H)
Dimensions: mm (")
Length (L)
420 (16-1/2)
1,720 (67-3/4)
W
H
*
1 Model number for North and Central American countries
North and Central
American countries
Weight according to EPTA-Procedure 01/2003: kg (lbs)*2
Cutting width: mm (") 300 (11-3/4)
PRODUCT
T
ECHNICAL INFORMATION
Accessory bag ........................... 1
Hex wrench (for M5) ................ 1
BCV02 (Battery converter) ....... 1 (for model BUR360ZX2C and
HRU01ZX2 only)
P 1/ 13
Repair
[1] NECESSARY REPAIRING TOOLS
CAUTION: Repair the machine in accordance with “Instruction manual” or “Safety instructions”.
Code No. Description Use for
1R036 Bearing setting plate 17.2
1R232 Pipe 30
1R285 Round bar for arbor 11-50
holding Ball bearing 6001ZZ when removing Spindle hub
1R130 Nose 10-30
1R089 Bearing extractor
removing Ball bearing 6901ZZ left in Gear box
holding Helical gear 33, when removing Spindle hub
removing Spindle hub
1R286 Round bar for arbor 12-50 removing Ball bearing 608DDW from Head case
1R350 Ring 60 supporting Motor housing set when assembling Motor section
1R308 Spring pin extractor 4.0 locking Cutter holder when loosening Cutter holder
[2] LUBRICATION
Apply Makita grease N. No.2 to the following portions designated with the black triangle to protect
parts and product from unusual abrasion.
Fig. 1
Item No. Description
Bent pipe complete a little
Gear box 3 g.
Square portion of Flexible shaft
O ring 22
a little
Whole portion
Gear room where Helical gear 33 engages with Armature’s gear
AmountPortion to lubricate
Armature
74
Helical gear 33 Spindle hub
31
31
74
87
87
74 viewed
from 31 side
P 2/ 13
[3] DISASSEMBLY/ASSEMBLY
[3] -1. Bent pipe complete
DISASSEMBLING
Disassemble Bent pipe complete as drawn in Fig. 2.
Fig. 2
1. While inserting 1R308 into the hole of
Cutter holder to stop Cutter shaft revolving,
turn Cutter assembly counterclockwise by
hand. Cutter assembly is removed from
Cutter shaft.
2. Loosen two M6x30 Hex socket
head bolts and remove Protector
cover and Protector.
Note: The M6x30 Hex socket
head bolts have Spring
washer 6 on each thread
to prevent losing.
It is not necessary to
separate them from
Protector.
Remove M5x10 Hex socket
head bolt and Protector clamp
from Head case complete, and
then Remove Head case complete
from Bent pipe complete by
loosening M5x25 Hex socket
head bolt.
M6x30 Hex socket
head bolt (2 pcs.)
M5x10 Hex
socket head bolt
Protector
clamp
Protector
Protector
cover
Cutter
assembly
male thread of Cutter shaft
(connected with Cutter
assembly at its inside)
1R308
M5x25 Hex
socket head bolt
Head case
3. Remove two M5x25 Hex socket head bolts and
separate Loop handle set* from Bent pipe complete.
4. Unscrew the following screws and bolts (11 pcs. in total),
and separate Grip R from Grip L.
*M5x25 Hex socket head bolt (2 pcs.)
*mark: The components of Loop handle set
*Clamp
cover B
*Clamp 33
M5x20 Pan
head screw
Grip R
M5x20 Hex
socket head bolt
M5x18 Hex
socket head bolt
4x18 Tapping
screws (8 pcs.)
Grip L
5. Pull off Bent shaft pipe complete from Pipe bracket by hand.
6. Pull off Pipe rubber and Spacer from
Bent pipe complete.
Pipe bracket
Bent pipe
complete
Spacer
Note: Some specifications
have no Spacer.
Pipe rubber
Bent pipe
complete
Repair
P 3/ 13
hole of Cutter
holder for 1R308
Bent pipe
complete
Bent pipe
complete
*Clamp 24
*Loop handle
[3] DISASSEMBLY/ASSEMBLY
[3] -1. Bent pipe complete (cont.)
[3] -2. Head case complete
ASSEMBLING
(1) Assemble Head case complete to Bent shaft pipe complete as drawn in Fig. 3.
(2) Assemble Loop hand set, Protector section, and Cutter assembly to Bent pipe complete in the reverse order of
Disassembly. Refer to Fig. 2.
Fig. 3
1. Pull out Flexible shaft to 100mm long from Bent shaft end.
Insert the square tip of Flexible shaft into the square hole
of Cutter shaft while turning.
1A. When replacing Flexible shaft with the new one,
place Bearing washer to the position that is 43 mm far
from the tip of Flexible shaft after step 1 shown above.
2. Align the hole of Head case complete with
the hole of Bend pipe complete.
The holes of Head case
complete and Bend pipe
complete for M5x10
Hex socket head bolt.
(1) Remove Head case complete from Bent pipe complete as Fig. 2.
(2) Remodel Hex wrench 5 as drawn in Fig. 4 to fit to the square hole of Cutter shaft.
DISASSEMBLING
1. File off the two edges in order to fit Hex wrench 5
to the square hole of Cutter shaft.
Fig. 4
Head case
complete
Square hole of Cutter shaft
Bearing washer
100 mm
Bent shaft end
Head case
complete
Bend pipe
complete
100 mm
43 mm
Flexible shaft
(new)
Repair
P 4/ 13
Square tip of
Flexible shaft
2. Hex wrench 5 can be fit to the square hole of Cutter shaft.
Loading...