Makita LC01Z User Manual

INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES

Cordless Cleaner Aspirateur sans fil Aspiradora Inalámbrica

LC01

IMPORTANT: Read Before Using. IMPORTANT: Lire avant usage. IMPORTANTE: Leer antes de usar.

010062

ENGLISH (Original instructions)

SPECIFICATIONS

Model LC01

Capacity 600 mL

Continuous use Approx. 12 min.

Overall length 966 mm (38-1/32")

Net weight 0.88 kg (1.94 lbs)

Rated voltage D.C. 10.8 V / 12 V max

• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.

• Specifications and battery cartridge may differ from country to country.

• Weight, with battery cartridge, according to EPTA-Procedure 01/2003

IMPORTANT SAFETY

INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.

WARNING

To reduce the risk of fire, electric shock or injury:

1. Do not leave appliance when battery fitted. Remove battery from appliance when not in use and before servicing.

2. Do not expose to rain. Store indoors.

3. Do not allow to be used as a toy. Close attention is necessary when used by or near children.

Standard battery cartridges BL1014

USA012-1

4. Use only as described in this

manual. Use only manufacturer's recommended attachments.

5. Do not use with damaged battery. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center.

6. Do not handle appliance with wet hands.

7. Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.

8. Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

9. Turn off all controls before removing the battery cartridge.

10. Use extra care when cleaning on stairs.

11. Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.

12. Use only the charger supplied by the manufacturer to recharge.

13. Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

14. Do not use without filters in place.

15. Do not charge the battery outdoors.

SAVE THESE

6. Do not block the intake hole or vent holes.

INSTRUCTIONS.

This appliance is intended for household use.

USB062-2

ADDITIONAL SAFETY RULES

1. Read this instruction manual and the charger instruction manual carefully before use.

2. Do not pick up the following materials:

− Hot materials such as lit cigarettes or spark/metal dust generated by grinding/cutting metal

− Flammable materials such as gasoline, thinner, benzine, kerosene or paint

− Explosive materials like nitroglycerin

− Ignitible materials such as Aluminum, zinc, magnesium, titanium, phosphorus or celluloid

− Wet dirt, water, oil or the like

− Hard pieces with sharp edges,

such as wood chips, metals, stones, glasses, nails, pins or razors

− Powder to clot such as cement or tonor

− Conductive dust such as metal or carbon

− Fine particle like concrete dust

Such action may cause fire, injury and/or property damage.

3. Stop operation immediately if you notice anything abnormal.

4. If you drop or strike the cleaner, check it carefully for cracks or damage before operation.

5. Do not bring close to stoves or other heat sources.

SAVE THESE INSTRUCTIONS.

ENC007-5

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CARTRIDGE

1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.

4. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with

any conductive material.

(2) Avoid storing battery cartridge

in a container with other metal objects such as nails, coins, etc.

(3) Do not expose battery cartridge

to water or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown.

6. Do not store the tool and battery

cartridge in locations where the temperature may reach or exceed 50 ﾟ C (122 ﾟ F).

7. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power.

2. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.

3. Charge the battery cartridge with room temperature at 10 ﾟ C - 40 ﾟ C (50 ﾟ F - 104 ﾟ F). Let a hot battery cartridge cool down before charging it.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched

off and the battery cartridge is removed before adjusting or checking function on the tool.

Installing or removing battery cartridge

1. Battery cartridge

2. Button

010014

•

Always switch off the tool before insertion or removal of the battery cartridge.

• To remove the battery cartridge,

withdraw it from the tool while pressing the buttons on both sides of the cartridge.

• To insert the battery cartridge, hold it so

that the battery cartridge front shape fits to that of the battery installment opening and slip it into place. Always insert it all the way until it locks in place with a little click. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.

• Do not use force when inserting the

battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly.

Switch action

1. Switch trigger

1. Capsule

2. Suction inlet

010063

CAUTION:

• Before inserting the battery cartridge

into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when

released. To start the tool, simply pull the switch trigger. Release the switch trigger to stop.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched

off and the battery cartridge is removed

before carrying out any work on the tool.

Disposing of Dust

CAUTION:

• Empty the cleaner before it becomes

too full, or the suction force weakens.

• Be sure to empty out the dust inside the

cleaner itself. Failure to do so may

cause the filter to be clogged or the

motor to be damaged.

1. Capsule

2. Suction inlet

010022

In order to drop dust sticking on the filter in the capsule, tap the capsule 4 or 5 times with your hand.

010023

Now point suction inlet downwards, turn capsule in direction of arrow in diagram, and disconnect capsule slowly and straight.

NOTE:

• Dust may spill out when capsule is

opened, so be sure to set a garbage bag beneath capsule.

1. Prefilter

010024

2. Capsule

Remove accumulated dust from inside of capsule and off of prefilter.

1. Prefilter

2. Securing lip

010025

Twist prefilter in direction of arrow to unfasten securing lip from cleaner unit and then pull off prefilter.

1. Filter

2. Prefilter

010026

Clean out fine dust from prefilter. Next, remove filter, and lightly tap to dislodge dust.

Reassembly

1. Filter

010070

Put on filter until it is fully in position on the cleaner unit.

NOTE:

• Make sure filter is put on straight

without being peeled back. If filter is put

on incorrectly as shown in diagram,

dust will get into motor housing, and

cause motor failure.

1. Filter

010028

Connect prefilter. At this time, make sure to twist prefilter so that securing lip is firmly locked into cleaner unit.

1. Prefilter

010029

2. Securing lip

010030

Connect capsule. Align projection on capsule with projection on handle and then firmly twist capsule in direction of arrow until it is secured.

010031

010032

1. Capsule

2. Handle

3. Projection

NOTE:

•

Always remove dust ahead of time, as suction power will be reduced if there is too much dust in cleaner.

• Always be sure to check that both filter

and prefilter are loaded correctly prior to using cleaner. If they are not loaded correctly, dust will get into the motor housing, and cause motor failure. If the following examples occur, filter and prefilter are not loaded correctly. Reload them correctly to rectify problem.

Problem Examples

Example 1: Only prefilter has been loaded (no filter)

1. Prefilter

010033

Example 2: Only filter has been loaded (no prefilter)

1. Filter

OPERATION

CAUTION:

• To connect attachments, such as nozzle,

twist-insert attachment in direction of arrow to ensure secure connection during use. To disconnect attachment, twist-extract also in direction of arrow. If attachment is twisted in the opposite direction, when being connected or disconnected, capsule may become loose.

1. Capsule

010034

Example 3: Filter has been loaded in a peeled back state

1. Filter

010028

Example 4: Prefilter's securing lip is not firmly locked into groove of cleaner housing

1. Groove of

010036

cleaner housing

2. Prefilter

3. Securing lip

010064

Cleaning (Suction)

Nozzle

Attach the nozzle to clean off tables, desks, furniture, etc. Nozzle slips on easily.

1. Nozzle

010065

Nozzle + Extension wand (Straight pipe)

The extension wand fits in between the nozzle and the cleaner itself. This arrangement is convenient for cleaning a floor while standing erect.

1. Cleaner body

2. Extension wand

3. Nozzle

010067

Corner nozzle

Fit on the corner nozzle for cleaning corners and crevices of a car or furniture.

1. Corner nozzle

2. Cleaner body

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched

off before attempting to perform inspection or maintenance.

After use

When storing the cleaner, hang it from a nail using the convenient hanger in back.

010068

Corner nozzle +Extension wand (Straight pipe)

In tight quarters where the cleaner itself cannot squeeze in, or in high places hard to reach, use this arrangement.

1. Corner nozzle

2. Extension wand

3. Cleaner body

010069

Cleaning without nozzle

You can pick up powder and dust without nozzle.

010066

010071

Cleaning

010072

From time to time wipe off the outside (cleaner body) of the cleaner using a cloth dampened in soapy water. Clean out also the suction opening, dust bag/dust pack mounting area and the dust stopper.

CAUTION:

• Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or cracks may result.

Wash the filter in soapy water when it is clogged with dust and the cleaner power becomes small. Dry it out thoroughly before use. An insufficiently dried filter may cause poor suction and shorten the service life of the motor.

010009

Symptom Area to be investigated Fixing method

Weak suction power

Not working

010051

Is filter clogged?

Is battery exhausted?

NOTE:

• Do not attempt to repair cleaner by

yourself. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are

recommended for use with your Makita

tool specified in this manual. The use of

any other accessories or attachments

might present a risk of injury to persons.

Only use accessory or attachment for its

stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.

• Extension wand (Straight pipe)

• Nozzle

• Nozzle for carpet

• Shelf brush

Things to Check Before Asking for Repairs

Empty dust from capsule.Is capsule full of dust?

Dust down or wash filter.

Recharge battery.

• Corner nozzle

• Round brush

• Flexible hose

• Filter

• Prefilter

• Various type of Makita genuine batteries

and chargers

MAKITA LIMITED ONE YEAR WARRANTY

Warranty Policy

Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace) without charge.

This Warranty does not apply where:

repairs have been made or attempted by others: repairs are required because of normal wear and tear: the tool has been abused, misused or improperly maintained: alterations have been made to the tool.

IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY. MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF "MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM OF THIS WARRANTY. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

EN0006-1

+ 22 hidden pages