• Important operating
and maintenance
instructions included.
NOTICE
DO NOT DISCARD THIS MANUAL
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
Congratulations!
Congratulations on selecting a SimpliFire Electric Fireplace, an elegant and clean alternative to wood & gas burning replaces.
The SimpliFire electric replace you have selected is designed to provide the utmost in safety, reliability, and ef ciency.
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE, OR MAINTAIN
THIS PRODUCT.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE
TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR
PROPERTY DAMAGE.
WARNING: To reduce risk of re, electrical shock, or personal injury, read all instructions
before using appliance.
Please contact your SimpliFire dealer or customer/technical support
(877-320-0730) with any questions or concerns.
For the location of your nearest SimpliFire dealer,
WARNING! Risk of Fire! Risk of Burns!
Risk of Electrical Shock!
DO NOT:
• Install or operate damaged heater
• Modify heater
• Operate the heater without fully assembling all
components
Hearth & Home Technologies Inc. disclaims any
responsibility for, and the warranty and agency listing will
be voided by the above actions.
When using electrical appliances, basic precautions should always be followed to reduce the risk of re, electric shock,
and injury to persons, including the following:
WARNING! DO NOT operate replace before reading
and understanding operating instructions. Failure to
operate appliance according to operating instructions
could cause re or injury.
WARNING! Improper installation, adjustment, alteration, service or maintenance can cause injury or
property damage. Refer to owner’s information manual
provided with this heater.
NOTICE! This appliance is not intended for use as a primary heat source and should not be factored as such in
residential heating calculations.
• Read all instructions before installing this appliance.
• This appliance is hot when in use. To avoid burns, do not let
bare skin touch hot surfaces. Keep combustible materials
such as furniture, pillows, bedding, papers, clothes, etc. and
curtains at least 3 ft. (0.9 m) from the front of the appliance
and keep them away from the sides and rear
• Extreme caution is necessary when any appliance is used
by or near children or invalids and whenever the appliance
is left operating and unattended.
• Do not operate any appliance if it malfunctions. Disconnect
power at service panel and have appliance inspected by a
reputable electrician before reusing.
• Do not insert or allow foreign objects to enter any ventilaion
or exhaust opening as this may cause an electric shock or
re, or damage the appliance.
• To prevent a possible re, do not block appliance connection
fan air intakes or exhaust in any manner.
• A appliance has hot and arcing or sparking parts inside. Do
not use it in areas where gasoline, paint, or ammable vapors
or liquids are used or stored.
• Use this appliance only as described in this manual. Any
other use not recommended by the manufacturer may cause
re, electric shock, or injury to persons.
• Do not operate any appliance with a damaged cord or plug
or after the appliance malfunctions, has been dropped or
damaged in any manner. Return appliance to authorized
service facility for examination, electrical or mechanical
adjustment or repair.
• Do not use outdoors.
• The appliance is not intended for use in bathrooms, laundry
areas and similar indoor locations. Never locate appliance
where it may fall into a bathtub or water container.
• Do not run cord under carpeting. Do not cover cord with
throw rugs, runners, or the like. Arrange cord away from
trafc areas and where it will not be tripped over. Do not
tightly coil cord.
• Always use properly grounded, fused and polarized outlets.
• Always use ground fault protection where required by
electrical code.
• To disconnect appliance, turn controls to “OFF” then remove
plug from outlet.
• Always disconnect power before performing any cleaning,
maintenance or relocation of the appliance.
• To prevent a possible re, do not burn wood or other materials
in this appliance.
• To prevent electrical shock or re, always use a certied
electrician should new circuits be required.
• When transporting or storing the appliance, keep in a dry
place free from excess vibration and store to avoid damage.
• Avoid use of an extension cord because an extension
cord may overheat and cause a fire. However if you
have to use an extension cord, the cord should be No.
14 AWG minimum size and rated to not less than 1875
watts.
Hearth & Home Technologies, on behalf of its brand SimpliFire (”SimpliFire”), extends the following warranty
for electric fireplaces that were purchased from a SimpliFire authorized dealer.
WARRANTY COVERAGE:
SimpliFire warrants to the original owner of the SimpliFire fireplace, and to any transferee taking ownership of the SimpliFire fireplace within one year following the date of original purchase, that the SimpliFire fireplace will be free from defects
in materials and workmanship at the time of manufacture. If a SimpliFire fireplace is found to be defective in materials or
workmanship during the applicable warranty period, HHT will, at its option, repair or replace the SimpliFire fireplace.
SimpliFire, at its own discretion, may fully discharge all of its obligations under such warranties by replacing the product
itself or refunding the verified purchase price of the product itself. The maximum amount recoverable under this warranty
is limited to the purchase price of the product. This warranty is subject to conditions, exclusions and limitations as
described below.
WARRANTY PERIOD:
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,
authorized SimpliFire dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date.
WARRANTY CONDITIONS:
This warranty only covers SimpliFire fireplaces that are purchased through a SimpliFire authorized dealer or distributor. A
list of SimpliFire authorized dealers is available on the SimpliFire websites.
WARRANTY EXCLUSIONS:
This warranty does not cover the following:
• Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and
exterior surface finishes may occur. This is not a flaw and is not covered under warranty.
• Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items,
or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.
• Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts
include: paint, batteries and the discoloration of glass.
• Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation
instructions, operating instructions, and listing agent identification label furnished with the appliance; (2) shipping or
improper handling; (3) improper operation, abuse, misuse, continued operation with damaged, corroded or failed
components, accident, or improperly/ incorrectly performed repairs; (4) environmental conditions (5) installation or use
of components not supplied with the appliance or any other components not expressly authorized and approved by
HHT; (6) modification of the appliance not expressly authorized and approved by HHT in writing; and/or (7) interruptions or fluctuations of electrical power supply to the appliance.
• Our obligation under this warranty does not extend to the SimpliFire fireplace’s capability to heat the desired space.
This warranty is void if:
• The fireplace is subject to or operated in atmospheres contaminated by chlorine, fluorine, or other damaging chemi-
cals.
• The fireplace is subjected to or operated in places with prolonged periods of dampness or condensation or weather.
Examples include but are not limited to outdoors, porches, and laundry rooms.
• There is any damage to the fireplace or other components due to water or weather damage.
LIMITATIONS OF LIABILITY:
• The owner’s exclusive remedy and SimpliFire’s sole obligation under this warranty, under any other warranty, express
or implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no
event will SimpliFire be liable for any incidental or consequential damages caused by defects in the appliance. Some
states do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply
to you. This warranty gives you specific rights; you may also have other rights, which vary from state to state.
EXCEPT TO THE EXTENT PROVIDED BY LAW, SIMPLIFIRE MAKES NO EXPRESS WARRANTIES OTHER THAN
THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION
OF THE EXPRESSED WARRANTY SPECIFIED ABOVE.
TYPE: Electric Air-Heaters Fixed and Location-Dedicated
Electric Room Heaters
STANDARD: UL 2021 (2nd Edition) CSA C22.2 No 46-M1988
NOTICE: This installation must conform with local codes.
NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.
This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be
factored as primary heat in residential heating calculations.
Note: The device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired
operation.
B. Unpacking and Inspecting Appliance
WARNING! DO NOT use this Electric Fireplace if any
part has been under water. Immediately call a qualied
service technician to inspect and to replace any part of the
electrical system if necessary. Keep plastic wrapping away
from children.
• Carefully remove the appliance and components from the
packaging. Discard packaging.
• Carefully inspect components for any damage.
• Reference parts list to verify all parts have been received.
• Read all the instructions before starting the installation.
Follow these instructions carefully during the installation to
ensure maximum safety and benet.
C. Model and Serial Number Information
The model and serial number information is located on the
rating plate. The rating plate is located on the left side of
the top surface of the appliance.
This equipment uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions , may cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of
the following measures:
• Increase the separation between the equipment and the
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Homeowner Reference Information
Model Name: ___________________________________________ Date purchased/installed: __________________
Serial Number: __________________________________________ Location on replace: _____________________
We recommend that you record the following pertinent
When choosing a location for your replace ensure that
the general rules are followed:
• For best results, install out of direct sunlight.
• Power supply service must be installed within
proximity of electric replace prior to nishing to
avoid reconstruction.
• See Figure 3.1 for appliance dimensions and to
determine location of appliance installation.
E. Clearance to Combustibles
Minimum Clearance to Combustible Construction
Sides.......................0 in.
Floor................13 3/4 in.
Top..........................0 in.
Back........................0 in.
Front..................... 36 in.
See Figure 3.2.
WARNING! Risk of Fire! Keep electrical cords, drapery,
furnishings or other combustibles at least 3 ft. (0.9 m)
from the front of the electric replace, and away from the
sides or rear.
F. Electrical Supply Circuit Requirements
Plan the location of the appliance so that it will have
adequate electric power. A 15 AMP, 120V/60hz circuit is
required. Additional appliances on the same circuit as
this appliance may exceed the current rating of that circuit. A dedicated circuit is not required, but is preferred
to prevent circuit breaker trips or fuse failure.
WARNING! Risk of Personal Injury or Property Damage! Failure to install the appliance as instructed below
may result in damage to the equipment and or may ex-
pose the user to the risk of re, serious injury, illness or
death.
A. Wall Mounting Bracket
SF-WM58
The wall mounting bracket must be used to mount the
appliance. This appliance must be mounted to a structural wall capable of bearing an 85 pound load.
• Remove bracket from back of unit.
• Determine the desired location of the appliance on
the wall depending on the size of unit.
Note: If installing on non-masonry wall, place the
wall mounting bracket in the desired location that
also aligns at least two required mounting points
(screws 5x40) with a structural framing member.
If installing on masonry wall, proceed to page 10 for
installation instructions.
• Ensure that the bracket is level.
• Mark six locations on the wall that correspond to the
six required mounting points in the bracket. See
Figure 4.1 & 4.7.
SF-WM70
The wall mounting bracket must be used to mount the
appliance. This appliance must be mounted to a structural wall capable of bearing a 110 pound load.
• Remove bracket from back of unit.
• Determine the desired location of the appliance on
the wall depending on the size of unit.
Note: If installing on non-masonry wall, place the
wall mounting bracket in the desired location that
also aligns at least four required mounting points
(screws 5x40) with a structural framing member.
If installing on masonry wall, proceed to page 10 for
installation instructions.
• Ensure that the bracket is level.
• Mark eight locations on the wall that correspond to
the eight required mounting points in the bracket.
See Figure 4.2 & 4.8.
• Orientate the bracket so that its mounting hooks are
pointing up as shown in Figure 4.11 and 4.13.
• Fasten the bracket to the wall.
Note: The bracket installation method varies depending on the wall construction (See Section B).
• Orientate the bracket so that its mounting hooks are
pointing up as shown in Figure 4.10 and 4.13.
• Fasten the bracket to the wall.
Note: The bracket installation method varies depending on the wall construction (See Section B).
= Required Mounting Points
Note: For non-masonry walls, at least two mounting
points (screws 5x40) must align with a structural
framing member.
Figure 4.1 SF-WM58 Mounting Bracket
= Required Mounting Points
Note: For non-masonry walls, at least four mounting
points (screws 5x40) must align with a structural
framing member.
The wall mounting bracket must be used to mount the
appliance. This appliance must be mounted to a structural wall capable of bearing a 135 pound load.
• Remove bracket from back of unit.
• Determine the desired location of the appliance on
the wall depending on the size of unit.
Note: If installing on non-masonry wall, place the
wall mounting bracket in the desired location that
also aligns at least six required mounting points
(screws 5x40) with a structural framing member.
If installing on masonry wall, proceed to page 10 for
installation instructions.
• Ensure that the bracket is level.
• Mark ten locations on the wall that correspond to the
ten required mounting points in the bracket. See
Figure 4.3 & 4.9.
• Orientate the bracket so that its mounting hooks are
pointing up as shown in Figure 4.12 and 4.13.
• Fasten the bracket to the wall.
Note: The bracket installation method varies depending on the wall construction (See Section B).
The wall mounting bracket can be installed on masonry
walls such as those constructed of brick or concrete,
or to framed walls constructed of wood or steel framing
sheathed with gypsum drywall, wood, etc. The method
used to mount the mounting bracket is different between
masonry walls and framed walls. Refer to the following
sections for more detail on the method applicable to this
installation.
Framed Wall
• For each of the marked mounting point locations,
determine which points align with a structural framing member.
• At the points where a wood or metal framing member exists, the 5 x 40 screw can be installed directly
into that structural member.
• Every mounting hole that does not align with a
structural framing member, a wall board toggle-bolt
anchor must be used. See Figure 4.4.
= Required Mounting Points
Note: For non-masonry walls, at least six mounting
points (screws 5x40) must align with a structural
framing member.
Figure 4.3 Mounting Bracket
Figure 4.4 3/16 Toggle-Bolt Anchor
• The toggle-bolt anchors are provided to accomodate
the required anchor points based on the appliance.
Use of toggle bolt anchors requires drywall thickness of minimum 1/2 in.
• Insert the bolt through the front side of the mounting
bracket and thread the toggle onto it from the rear of
the bracket. See Figure 4.5.
• Fold the toggle wings ush against the bolt and push
them through a drilled hole until they expand open
on the other side. See Figure 4.6.
• Pull back on the bolt and tighten. See Figure 4.6.
Note: This product cannot be installed on a wall
sheathed with drywall less than 1/2 in. thick, unless
all six anchor points in the mounting bracket align
with structural framing members.
WARNING! Risk of Damage or Personal Injury! Allowable pull-out and shear strength are 25% of ultimate
values or less, as required by building authorities.
Figure 4.5 Toggle Bolt Installation through Mounting Bracket
Figure 4.6 Installing Anchors in Hollow Wall
Masonry Wall
• In the marked locations, drill 5/16 in. diameter x 2 in.
deep holes. See Figure 4.7 (SF-WM58), Figure 4.8
(SF-WM70) or Figure 4.9 (SF-WM94).
• Insert the provided wall anchors into the holes.
• Gently tap the anchors with a hammer until they are
ush with the wall surface.
• With mounting hooks pointed up, attach the bracket
to the masonry anchors with 5 x 40 screws . See
Figure 4.10 (SF-WM58), Figure 4.11 (SF-WM70) or
Figure 4.12 (SF-WM94).
Masonry Anchors
Figure 4.8 (SF-WM70) Masonry Anchor Placement
Wall
Masonry Anchors
Figure 4.9 (SF-WM94) Masonry Anchor Placement
WARNING! Risk of Damage or Personal Injury! Do
not use supplied masonry anchors on hollow walls,
sheathed with wood, sheetrock, drywall or other materials.
CAUTION! Risk of Injury! It is recommended that Glass
assembly installation and removal be performed by two
people.
• Install glass front as shown in Figure 4.14. Orientate
front so that LED lighting connector is towards the oor.
• Install glass front so that the tabs on its back side
engage the slots in the top of the appliance.
• Once both tabs engage, press rmly against the bottom
face of the glass panel to engage the bottom connectors.
Note: The tabs on the two center mounting brackets
on the glass will not fully engage the corresponding
slots in the appliance.
• Secure the glass front to the appliance with two
provided M4x8 screws through the two glass front
mounting brackets. See Figure 4.14.
• Connect the electrical cable from the glass front
backlighting to the corresponding cable on the lower
right of the appliance. Note: The backlight cable
plug on the appliance is accessed by removing its
access cover on the lower right of the appliance.
F. Electrical Connection
WARNING! Risk of Fire, Electrical Shock and Injury!
Electrical wiring must comply with local building codes
and other applicable regulations to reduce the risk of
re, electrical shock and injury.
A 15 AMP, 120 Volt, 60 Hz. circuit with a properly
grounded outlet is required. The unit comes with a 6 ft.
long three wire 16AWG IEC-320 power cord.
The appliance power cord has a three pin NEMA-5-15P
plug (Figure 4.15A). An adapter must be used for connecting to a two-slot receptacle (Figure 4.15C). The
green grounding wire extending from the adapter must
be connected to a permanent ground such as a properly
grounded outlet box. The adapter should not be used if
a three slot grounded receptacle is available.
Secure with
Screw Here
Figure 4.14 Attaching Front to Appliance
Figure 4.15 Cord Electrical Connection
WARNING! Risk of Fire! Do not plug in or operate this
product with hot air vents touching the ground. Always
hang on wall with supplied bracket before use.
WARNING! Risk of Fire, Electrical Shock and Injury!
Ensure the power cord is not installed so that it is pinched
or against a sharp edge and ensure that the power cord is
stored or secure to avoid tripping and snagging.
CAUTION! The unit’s power cord must be connected to
a properly grounded and protected 120V outlet. Always
use ground fault protection where required by the electrical code.
WARNING! Risk of Fire, Electrical Shock, and Injury!
Do not operate the unit if it is damaged or has malfunc-
tioned. If you suspect the unit is damaged, call a qualied
service technician to inspect and replace any part of the
electrical system if necessary.
A. Manual Switch Function
The appliance can be operated by both remote control
and manual button. Once the unit has been properly
connected to a grounded electrical outlet, turn on the
main power switch located on the right side of the appli-
ance . A beep should be heard when the power is rst
applied. See Figure 5.1.
Main Power Switch
The POWER switch supplies power to all functions of
the replace. This switch must be in the “ON” position
for any of the functions including the remote.
Flame Button
By pressing the FLAME button, the unit will cycle
through four ame effects.
Heater Button
- Press the heater button once to turn 750W power on.
Appliance will beep and illuminate 1 red LED.
- Press again turns 1500W power on.
Appliance will beep and illuminate 2 red LEDs.
- Press third time turns heater off.
Note: A harmless slight brief odor may occur during rst
use or after prolonged period of storage.
NOTE:
There is a brief delay between the heater command and
the heater turning ON. When the appliance receives
a heater ON command, the appliance blower will turn
ON for 8 seconds before the heater turns ON. There is
also an 8 second delay between heater off and blower
shutdown.
Note: To use both remote and manual function, the main
power switch must in “ON” position.
• The appliance Main Power Switch must be in the
“ON”position for the remote control to function.
• Make sure batteries are properly installed in Remote
Control.
- Battery requirements 2 x AAA batteries
(included)
• The effective range of the remote is up to 13 ft.
• The remote control must be within the 13 ft. range and
also be pointed directly at the face of the appliance.
For best results, position the remote control within 45
degrees of the face of the appliance
C. Resetting Temperature Cutoff Switch
The heater is protected with a safety device to prevent
overheating. Should the heater overheat, an automatic cutoff will turn the heater OFF. It will not turn ON
automatically without being reset. If it overheats for any
reason, it can be reset by:
1. Turn appliance to off
2. Unplug unit and wait 5 minutes
3. Plug in and turn on.
CAUTION: If appliance overheats repeatedly, discontinue use and call customer / technical support.
CAUTION: If you need to continuously reset the heater,
unplug the appliance and contact customer / technical
support.
ICONTITLEFUNCTION REMOTE LCD
DISPLAY
The POWER button will turn the
replace on. It will also put the
POWER
FLAME
HEATER
THERMOSTAT
TIMER
LIGHT
replace in a standby mode.
This will turn off all functions at
once but will hold the settings in
memory except Heater function.
The unit will turn on at the same
settings by pressing the power
button again.
By pressing the FLAME button,
the unit will cycle through four
ame effects.
Press Heater button once 750W
heater turns on.
Press Heater button twice 1500W
turns on,
Press Heater button three times,
turns off heater.
Pressing the Temperature button
adjusts the heaters response
to the ambient temperature
conditions in the room.
Temperature adjusts from 16 °C
- 28 °C (61 °F - 82 °F). Power
button must be on to set °C to °F.
Hold for 3 seconds and the LCD
display from °C to °F.
Pressing the Timer button sets
the time desired for the replace
to run. The Timer can be set from
.5 hour up to 9 hours in 1 hour
increments.
Pressing the Light button
changes the glass fascia
backlight colors (14 colors
available), and turns it on/off.
LCD illuminates and
displays ame status
Icon and temperature
set point.
LCD illuminates and
displays ame status
icon.
LCD illuminates
and displays heater
status icon.
Remote displays
the temperature. If
in Stand-by mode,
temperature displays
but cannot be
adjusted.
Remote will display
the time setting
selected. If in Standby mode time will
display but cannot be
adjusted.
No indicator.
FIREPLACE RESPONSE
Fireplace emits single audible beep
to conrm command to transition to
ON or STANDBY state
Fireplace emits single audible beep
to conrm command to transition
between four FLAME states.
Fireplace emits signal audible
beep to conrm command to
transition between HEATER states.
Fireplace displays one red LED for
WARNING! Risk of Shock! Always unplug the cord before moving or servicing. Do not immerse appliance in
water.
• Always turn OFF the appliance and disconnect the
cord from the electrical outlet before cleaning your
appliance.
• Light accumulated dust may be removed from the ap-
pliance exterior with a soft cloth or vacuum cleaner.
• Wipe the exterior surfaces of the appliance occasion-
ally with a slightly microfiber cloth using a solution of
mild detergent and water. Dry thoroughly before operating the appliance.
CAUTION! Do not allow water to run into the interior of
the appliance as this could create a re or electric shock.
Always unplug the cord before moving or servicing.
• The fan motor is factory lubricated for life and will not
require further lubrication.
• Store appliance in a clean dry place when not in use.
WARNING! Risk of Fire! To reduce risk of re, do not
store or use gasoline or any other ammable vapors or
liquids in the vicinity of the appliance.
B. Cleaning
Cleaning Glass
Dust particles can be removed by bufng lightly with a
clean dry cloth. Fingerprints and other marks can be
cleaned with a cloth dampened with a quality household
glass cleaner. The glass should be completely dried with
a lint free cloth or paper towel. Do not use abrasive cleaners on glass surface. Do not spray liquids directly onto
any surface.
Metal Surface
Dust particles can be removed by bufng lightly with a
clean dry cloth. A damp cloth can be used to clean painted surfaces. Do not use abrasive cleaners. Do not spray
liquids directly on to any surface.
C. Servicing
Except for installation and cleaning described in this manual, an authorized service representative should perform
any other servicing.
WARNING! Risk of Electrical Shock! Any other servicing needed must be performed by an authorized service
representative. Do not attempt to service the unit yourself.
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Provide
model number and serial number when requesting service parts from your dealer or distributor.
ITEMDESCRIPTIONCOMMENTSPART NUMBER
1Black Glass
2White Glass
3Remote
4Fan Box
Power CordCORD-WM58
5
6Hanging Bracket
Flame Rod, 58"
Rock Kit, Contains both White and Clear Rock
Hardware Bag
Includes: Masonry Anchors, Screw (ST5 x 40), Bolt (M4 x 8), Bolt (M5 x 10), 3/16 Toggle anchor
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Provide
model number and serial number when requesting service parts from your dealer or distributor.
ITEMDESCRIPTIONCOMMENTSPART NUMBER
1Black Glass
2Remote
3Fan Box
Power CordCORD-WM58
4
5Hanging Bracket
Flame Rod, 70”
Rock Kit, Contains both White and Clear Rock
Hardware Bag
Includes: Masonry Anchors, Screw (ST5 x 40), Bolt (M4 x 8), Bolt (M5 x 10), 3/16 Toggle anchor
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Provide
model number and serial number when requesting service parts from your dealer or distributor.
ITEMDESCRIPTIONCOMMENTSPART NUMBER
1Black Glass
2Remote
3Fan Box
Power CordCORD-WM58
4
5Hanging Bracket
Flame Rod, 94”
Rock Kit, Contains both White and Clear Rock
Hardware Bag
Includes: Masonry Anchors, Screw (ST5 x 40), Bolt (M4 x 8), Bolt (M5 x 10), 3/16 Toggle anchor