Magellan MG-6060 User Manual

All-In-One Wireless Security System V1.0

Model #: MG-6060

Reference and Installation Manual

Table of Contents

Introduction................................................... 3

About Magellan and this Manual............................. 3

Conventions ............................................................ 3

Specifications.......................................................... 3

Quick Setup................................................... 4

Installation..................................................... 6

AC Power................................................................ 6

Backup Battery Pack............................................... 6

Telephone Line Connections .................................. 6

Programmable Outputs (PGMs) ............................. 7

Hardwire Zone Connections ................................... 8

WinLoad Connection............................................... 8

UIP-256 Universal In-Field Programmer

Connection.............................................................. 8

X10 Transmitter Connection ................................... 9

Connecting a Paradox Memory Key (PMC-3)......... 9

Location and Mounting............................................ 9

Connecting the Radio Antenna ............................. 10

Programming Methods .............................. 11

WinLoad Installer Upload/Download Software...... 11

Programming Using the Built-in Keypad ............... 11

Programming Using a Paradox Memory Key........ 11

User Codes.................................................. 12

User Code Length................................................. 12

Installer Code........................................................ 12

Maintenance Code ................................................ 12

System Master Code ............................................ 12

Duress Code ......................................................... 12

Zone Programming..................................... 13

Zone Programming Overview ............................... 13

Zone Definitions .................................................... 13

Zone Options ........................................................ 15

Zones 15 and 16 become Hardwire Zones........... 16

EOL (End-Of-Line) Zones ..................................... 16

Wireless Programming .............................. 17

Assigning Wireless Zone Transmitters ................. 17

Assigning Wireless Doorbells to the Console ....... 17

Deleting Assigned Wireless Transmitters ............. 17

Viewing Wireless Transmitter Signal Strength...... 17

Assigning Remote Controls .................................. 18

Programming the Remote Control’s Buttons ........ 18

Arming and Disarming ............................... 20

Regular Arming Switches to Stay Arming ............. 20

Regular Arming Switches to Force Arming ........... 20

Stay Arming Switches to Force Arming ................ 20

Timed Auto-Arming ............................................... 20

No Movement Auto-Arming ................................... 20

Auto-Arming Options ............................................. 20

One-Touch Arming................................................ 21

Exit Delay .............................................................. 21

Bell Squawk on Arm/Disarm with Remote Control 21 No Exit Delay when Arming with Remote Control . 21

Exit Delay Termination .......................................... 21

Follow Zone Switches to Entry Delay 2................. 21

Closing Delinquency Timer ................................... 21

Alarm Options............................................. 22

Bell Cut-off Timer .................................................. 22

Wireless Transmitter Supervision Options ............ 22

Tamper Recognition Options ................................ 22

Check-in Supervision Options ............................... 22

Panic Alarms ......................................................... 23

Reporting and Dialer Settings................... 24

Report Codes ........................................................ 24

Console Telephone Numbers ............................... 25

Console Account Number ..................................... 26

Reporting Formats ................................................ 27

Event Call Direction............................................... 27

Delay Between Dialing Attempts ........................... 28

Alternate Dial Option ............................................. 28

Force Dial Option .................................................. 28

Dialing Method ...................................................... 28

Pulse Ratio............................................................ 28

Switch to Pulse Dialing on 5th Attempt ................. 28

Telephone Line Monitoring (TLM) ......................... 28

Recent Close Delay .............................................. 28

Auto-Test Report................................................... 29

Power Failure Report Delay .................................. 29

Disarm Reporting Options ..................................... 29

Zone Restore Report Options ............................... 29

Programmable Outputs ............................. 30

PGM Activation Event ........................................... 30

PGM Deactivation Event ....................................... 30

PGM Delay............................................................ 30

PGM Normal State ................................................ 30

PGM X10 Option ................................................... 30

System Settings ......................................... 31

Software Reset...................................................... 31

Installer Lock ......................................................... 31

Console Tamper Supervision ................................ 31

Console Audible Trouble Warning ........................ 31

FM Tuner Option ................................................... 31

Daylight Savings Time .......................................... 31

AC Power Failure Warning.................................... 31

The Trouble Display .............................................. 31

WinLoad Software Settings....................... 33

Paradox Magellan Systems 1

Panel Answer Options ........................................... 33

Panel Identifier....................................................... 33

PC Password ......................................................... 33

PC Telephone Number .......................................... 33

Call Back Feature .................................................. 33

Appendix 1: Ademco Contact ID Report Code

List ............................................................... 34

Index ............................................................ 37

2 Reference & Installation Manual

Introduction

About Magellan and this Manual

Magellan is designed for fast and easy installation. Simply remove it from the box, mount the console and wireless transmitters, apply power and Magellan is ready to protect your home. Magellan has already been pre-programmed with the required settings for a basic security installation.

Some of Magellan’s features can be programmed through a quick Installer Menu (menu programming) or through section programming. Use the quick setup chapter (page 4) to install the Magellan console quickly and with the basic programming required for a standard security application. All other chapters (pages 6 to 33) are for advanced section programming. These other chapters provide more in-depth and precise information if more advanced programming is required.

We recommend that you read this entire manual before you begin installation.

Conventions

This symbol designates a reference to another section, manual or guide.

This symbol designates either a warning or important information.

Specifications

Power input: AC*:9Vac, 1A/9VA transformer or

16.5Vac, 20VA transformer

DC: 12Vdc to 18Vdc power supply

Current consumption:With AC input: 600mA

With DC input: 400mA

Backup Battery: 7.2Vdc, 1.8 to 2.0Ah NiMH rechargeable

battery pack (order # 0780100178)

PGMs: Two N.O. solid-state relays (not polarized)

Internal resistance - 169 (max.) Max. current consumption - 50mA

* It is recommended that you use a 9Vac 1A/9VA transformer to power the Magellan console. The console will generate less heat when connected to a 9Vac transformer than when connected to a 16.5Vac transformer.

[

DATA

This symbol designates a reminder or suggestion.

] =

- Text shown in this manner designates data or programming information that is entered through the console’s keypad.

- Text shown in this manner can also designate a specific key that has to be pressed.

Paradox Magellan Systems 3

Quick Setup

Follow these steps to quickly set up Magellan with the required settings for a basic security installation.

1.Getting Started

1. After powering up for the first time, press [

START

] to access the

Installer Menu.

2. The first menu option will appear.

Press [

] to go to the “User

Profile” menu.

2.User Programming

1. From the “User Profile” menu,

press [

2. Select which user you wish to add by pressing [ desired user appears, press [ and follow the menus to set:

- Access Code

- User Label

- Remote Control When you are done the next menu option will appear (see Central Station Reporting below).

]. When the

For more in-depth programming of the console’s communication features, see Reporting and Dialer Settings on page 24.

4.Adding and Programming Zones

1. From the “Zone Profile” menu,

press [

2. Select which zone you wish to add by pressing [

[

number appears.

3. Press the tamper switch on the transmitter you wish to assign to the selected zone. Follow the menus to set:

- Zone Label

- Zone Type

- Other Zones

When you are done the next menu option will appear. Press

]

] until you see the “System Test” menu or press the [5] key

[

to immediately access the “System Test” menu.

For more in-depth programming of the console’s zones, see Zone Programming on page 13 and Wireless Programming on page 17.

] when the desired zone

] and press

For more in-depth programming of the remote controls, see Programming the Remote Control’s Buttons on page

18.

5.Testing the Magellan System

1. From the “System Test” menu,

press [

3.Central Station Reporting

1. From the “Communicator” menu,

press [

2. Press [

] and follow the menus

to set:

- Telephone numbers

- Account Number

- Report Format When you are done the next menu option will appear. Press

] until you see the “Zone

[

WARNING! When testing the hardware, the speaker and sirens will also be tested. Avoid close proximity to the Magellan console when performing the hardware test to avoid any damage to your hearing.

Profile” menu or press the [6] key to immediately access the “Zone Profile” menu.

4 Reference & Installation Manual

2. Select which test you wish to

perform by pressing [

press [

] when the desired test

] and

appears. The following tests can be performed:

- Zone tests

- Remote control tests

- Reporting tests

- Hardware tests

When you are done the next menu option will appear. Press

[

] until you see the “Passwords” menu or press the [8] key

to immediately access the “Passwords” menu.

6.Passwords

Deleting Zones

1. From the “Zone Profile” menu, press [OK].

1. From the “Passwords” menu, press [OK].

2. Select which password(s) or code(s) you wish to program by

pressing [

] and press [OK]

when the desired password appears. The following passwords can be programmed:

- Installer code

- Maintenance code

- Panel ID

- PC Password

When you are done the next menu option will appear. Press

EXIT

[

For more in-depth programming of the console’s passwords, see User Codes on page 12 and WinLoad Software Settings on page 33.

7.Time and Date

2. Select which zone you wish to delete by pressing [ the desired zone number appears.

3. Press [

4. Press [ press [

When you are done the next menu option will appear. Press you see the “System Test” menu or press the access the “System Test” menu.

For more in-depth programming of the console’s zones, see Zone Programming on page 13 and Wireless Programming on page 17.

] and press [OK] when

YES

]. To delete another zone,

YES

] and then repeat steps 2 to

[5]

key to immediately

[

]

until

1. Press the [

2. Press [

] key.

] until you reach the “Time and Date” menu and press [OK] or press the [3] key to access the “Time and Date” menu.

3. Select the time format (12Hrclock or 24Hr-clock) and then program the time. Press [

when done.Program the date by entering the 4-digit year first, followed by the 2-digit month and then the 2-digit day. Press [ when done.

]

Paradox Magellan Systems 5

Installation

AC Power

Magellan requires a 9Vac (1A/9VA) or 16.5Vac (20VA) transformer (not included) to supply power to the console.

Connect the transformer to the on page 6.

Magellan can also be powered through a DC power supply. Connect a 12Vdc to 18Vdc to the console.

Do not use any switch-controlled outlets to power the transformer.

Figure 1: Connecting the Transformer

terminals as shown in Figure 1

terminals to power the

Back view of the Magellan console.

Do not use any switch- controlled outlets.

Figure 2: Connecting the Backup Battery (cont’d)

Slide in the battery pack horizontally, tilt the battery pack downward and then tuck it in Magellan’s battery compartment.

Tuck the cables in the specially

designed slot.

Snap in the battery

compartment cover when finished.

Telephone Line Connections

Partial view of the backside of the Magellan console

9Vac (1A/9VA) to

16Vac (20VA)

Insert the transformer’s wires into the AC terminals.

transformer

Backup Battery Pack

Magellan uses a backup battery pack to provide power during a power loss. A 7.2Vdc 1.8 to 2.0Ah NiMH (Nickel Metal Hydride) rechargeable battery pack is included with the Magellan console. Connect the battery pack as shown in Figure 2 on page 6.

Connect the backup battery pack after applying AC power.

Figure 2: Connecting the Backup Battery

Partial view of the backside of the Magellan console

The Magellan console can be connected to a telephone line by connecting the telephone company’s wires directly to Magellan’s dialer or by connecting a standard 4-pin RJ-11 cable between

LINE

the

plug of the console to a standard telephone wall jack.

Direct Connect

Connect the telephone line through an RJ31X jack as shown in Figure 3 on page 6.

Figure 3: Telephone Line Direct Connect

Back view of the Magellan console.

To connect the telephone line:

1. Connect an RJ31X to the

-1,

RING

and

1, terminals as shown at right.

2. Connect the telephone company wires and the home telephone to the RJ31X.

TIP

Insert the backup battery’s

plug into the connector

BATT

labeled

6 Reference & Installation Manual

For UL compliant installations, the Magellan console must be able to seize the telephone line and place a call in an emergency situation. It must be able to do this even if other equipment (telephones, answering machines, computer modems, etc.) already has the line in use. To do so, the Magellan console must be connected to a properly installed RJ31X jack that is electronically in series with and ahead of all other equipment attached to the same telephone line. Proper installation is depicted in the diagram below. If you have any questions concerning these instructions, you should consult your telephone company about installing the RJ31X jack and the Magellan console for you.

Programmable Outputs (PGMs)

Magellan comes equipped with two 50mA solid-state PGM outputs. When a specific event occurs in the system, a PGM can be programmed to activate lights, garage door openers, etc. See Programmable Outputs on page 30 for more information on programming PGMs.

Connect Magellan’s PGM outputs as shown in Method 1 in Figure 5 on page 7. Since Magellan does not come with a power supply, an external power supply must be employed to power the circuit. The PGM outputs can be either Normally Open (N.O.) or Normally Closed (N.C.) as detailed in PGM Normal State on page 30.

If the current draw on the PGMs is to exceed 50mA, we recommend using an external relay as shown in Method 2 in Figure 5 on page 7.

Using Method 2, connect the device to the output terminal of the external relay that matches the normal state of Magellan’s PGM output. For example, if PGM1’s normal state is Normally Open (N.O.), connect the device to the relay.

Figure 5: PGM Connections

Back view of the Magellan console.

N.O

. terminal of the external

Method 1

(less than 50mA)

Line Plug Connect

The Magellan console can also be connected to a telephone line

LINE

via its on-board information on connecting the telephone line using this method.

When connecting via the shared and it is busy (i.e. someone is talking on the telephone) the console will be unable to communicate with the Central Monitoring Station. It is recommended that the Direct Connect method (page 6) be used to connect the telephone line.

Back view of the Magellan console.

1. Insert one end of the 4-pin RJ-11 cable into the

LINE

plug of the Magellan console.

2. Insert the other end of the RJ-11 cable into a standard telephone wall plug.

plug. See Figure 4 on page 7 for more

LINE

plug, if the telephone line is

Figure 4: Line Plug Connection

4-pin

RJ-11

cable

External

Power Supply

Method 2

(exceeds 50mA)

External relay

External

Power Supply

Devices such as a light, etc.

Paradox Magellan Systems 7

Hardwire Zone Connections

Magellan comes with two on-board hardwire zones. You can connect hardwire detection devices such as door contacts to Magellan’s zone terminals. Connect the detection devices as shown in Figure 6 on page 8. Please note the following:

• Section [095] options [1] and [2] must be enabled in order to use the two on-board hardwire zones. See Zones 15 and 16 become Hardwire Zones on page 16 for more information.

• After connecting the detection devices, the zones must be defined. See Zone Programming on page 13 for more information.

• The hardwire zones follow the console’s EOL and tamper definitions.

Though any hardwire detection device can be connected to Magellan’s on-board hardwire zone inputs, it is recommended that only devices that do not require a power source (i.e. standard door contacts) be connected. Since Magellan has no power supply, an external power supply would have to be connected in order to power hardwire detection devices that do require a power source.

Figure 6: Hardwire Zone Connections

Back view of the Magellan console.

Figure 7: Connecting to WInLoad

Back view of the Magellan console.

4- to 10-pin cable

(supplied with

the 306 Adapter)

connector

306 Adapter

Standard

Computer containing

WinLoad software

DB-9 cable

(9-pin serial cable)

UIP-256 Universal In-Field Programmer Connection

4-pin

cable

Hardwire zone 2

(zone 16)

1K9 EOL

Hardwire zone 1 (zone 15)

1K9 EOL

WinLoad Connection

The Magellan console can be programmed and monitored through the WinLoad Installer Upload/Download Software for Windows®. WinLoad allows for remote or on-site uploading and downloading using most standard modems. It also allows for advanced printing of reports and supports several languages simultaneously. Connect Magellan to a computer containing the WinLoad software as shown in Figure 7 on page 8.

Refer to the WinLoad’s Online Help for more information on WinLoad.

Magellan’s firmware can be upgraded locally using the UIP-256 Universal In-Field Programmer. The UIP-256 includes proprietary PC software, cables to interconnect Magellan and a PC, as well as two 9V batteries. Connect the UIP-256 as shown in Figure 8 on page 8.

Refer to the Universal In-Field Programmer (UIP-256)

Instructions for more information.

Figure 8: Connecting the UIP-256

Connect the 10-pin cable of the UIP-256 to the 10-pin connector of

the Magellan console.

UIP-256

Universal In-Field

Programmer

Standard

DB-9 cable

(9-pin serial cable)

Back view of the Magellan console.

Download latest

Magellan

firmware from

www.paradox.ca

8 Reference & Installation Manual

X10 Transmitter Connection

Magellan supports the X10 communication protocol. X10 is a communication protocol for remote control of electrical devices such as lamps and appliances. Communication is accomplished through standard household electrical wiring using X10 transmitters and receivers. Configure Magellan, with the use of an X10 transmitter, to automate a home. Connect the X10 transmitter as shown in Figure 9 on page 9.

Refer to the Magellan X10 Instructions on our website, www.paradox.ca, for information on using and configuring Magellan’s X10 feature.

Figure 9: Connecting the X10 Transmitter

Back view of the Magellan console.

1. Connect one end of the 4pin RJ11 cable into the

10 plug of the console.

2. Connect the other end of the 4-pin RJ11 cable into the X10 transmitter.

3. Plug the X10 transmitter into a standard wall outlet.

Location and Mounting

Location

The locations of Magellan and its wireless transmitters affect the overall performance of the wireless system. To ensure the best signal reception, the following list of location criteria should be respected whenever possible:

• Select an installation site that is free of obstacles that reflect and absorb radio frequency (RF) signals, as well as interference that may distort signals. Avoid installation near or in the path of strong RF fields (i.e. neon lights, computers), and on or near metal objects, circuit breakers boxes, air conditioners and heater ducts since they may cause interference and reduce the console’s sensitivity.

• Select a site that is not susceptible to drastic temperature changes.

• Mount the Magellan console as central as possible to the proposed placement of the wireless transmitters.

• Mount the Magellan console as high as possible.

• Avoid installing Magellan in the basement as the range of the console is reduced when installed below ground level. However, if it is absolutely necessary to install the console in the basement, install the console as high as possible.

• Install the Magellan console on a wall allowing at least 5cm (2”) around the console to permit adequate ventilation and heat dissipation.

4-pin RJ11 cable

X10 transmitter

Connecting a Paradox Memory Key (PMC-3)

When using a Paradox Memory Key with a Magellan console, remove power (both AC and battery power), connect the memory key to the 5-pin connector on the back of the Magellan console as shown in Figure 10 on page 9. Once connected, re-apply power to the console. For more information, see Programming Using a Paradox Memory Key on page 11.

Figure 10: Connecting a Paradox Memory Key (PMC-3)

The Wall Plate

Magellan uses a plastic wall plate to stay mounted on a wall. The wall plate is also used for tabletop mounting to cover the back of the console as well as keep any wires within their respective wire slots. After choosing an appropriate location (see Location on page 9), mount the wall plate onto the Magellan console with two screws as described in Mounting Magellan on the Wall on page 10 or Tabletop Mounting on page 10.

Figure 11: Wall Plate

Jumper ON: Read from and/or write to memory key

Jumper OFF: Write protected (read from memory key only)

Paradox Magellan Systems 9

Figure 12: Mounting Magellan onto the Wall Plate

rubber stops prevent the console from sliding when Magellan is being used. To do so:

1. Place the console back plate flush against the wall plate.

2. Slide the Magellan’s open slots labeled D (see Figure 13 on page 10) onto the wall plate’s tabs labeled B (see Figure 12 on page 10).

3. Gently apply downward pressure to insert the wall plate’s tabs into Magellan’s open slots.

4. Insert two screws through the wall plate’s screw holes labeled C and into holes labeled E (see Figure 13 on page

10) in the Magellan back plate.

5. Attach the plastic feet and rubber stops as shown in Figure 14 on page 10.

Figure 14: Mounting Magellan on a Tabletop

Plastic feet

(x2)

Figure 13: Magellan’s Back Plate

Mounting Magellan on the Wall

Magellan can be mounted on a wall by first securing the wall plate (see The Wall Plate on page 9) to the wall and then

Wall

plate

Rubber stops

(x2)

Tabletop

Tabletop mounting may not be an approved installation method by local regulations. It is recommended that the local regulations be verified prior to installing the Magellan console using this method.

mounting the Magellan console on the secured wall plate as shown in Figure 12 on page 10 and Figure 13 on page 10. To do so:

Connecting the Radio Antenna

1. Place the wall plate on the desired spot of the wall.

2. Drill and insert screws into holes labeled A as shown in Figure 11 on page 9.

3. Place the console back plate flush against the mounted wall plate.

4. Slide the Magellan’s open slots labeled D (see Figure 13 on page 10) onto the wall plate’s tabs labeled B (see Figure 12

If the radio’s reception is not very good, connect the supplied

ANT

radio antenna to the

terminal on the back of the Magellan console as shown in Figure 15 on page 10. Move the antenna around until the spot with the best reception is found.

Figure 15: Connecting the Radio Antenna

on page 10).

5. Gently apply downward pressure to insert the wall plate’s tabs into Magellan’s open slots.

6. Insert two screws through the wall plate’s screw holes labeled C and into holes labeled E (see Figure 12 on page 10 and Figure 13 on page 10) in the Magellan back plate. This will secure the console to the wall.

Radio

Tabletop Mounting

Magellan can also be mounted on a tabletop. This is a useful convenience that allows Magellan to be situated on a nightstand,

Back view of the Magellan console.

Antenna

desk, kitchen counter, etc. Included with Magellan are two plastic feet as well as two rubber stops. The plastic feet raise the Magellan console to a slight angle for easy viewing while the

10 Reference & Installation Manual

Programming Methods

WinLoad Installer Upload/Download Software

Program the Magellan console remotely or on-site using the WinLoad Installer Upload/Download Software for Windows®. For more information, contact your local Paradox Distributor or visit our Web site at www.paradox.ca. If you are using the WinLoad software, you must program the features explained on page 33.

Please refer to WinLoad’s Online Help for more information on using WinLoad.

Programming Using the Built-in Keypad

Use the built-in keypad to access Magellan’s programming mode.

Use the supplied Magellan Programming Guide to keep track of which sections were programmed and how.

To access programming mode:

1. Press and hold the [0] key.

2. Enter your [

3. Enter the 3-digit [

4. Enter the required [

INSTALLER CODE

SECTION

DATA

There are two methods that can be used to enter data when in programming mode; Single Digit Data Entry and Feature Select Programming methods.

Single Digit Data Entry Method

After entering programming mode, some sections will require that you enter decimal values from 000 to 255. Other sections will require that you enter hexadecimal values from 0 to F. The required data will be clearly indicated in this manual as well as in the Magellan Programming Guide. When entering the final digit in a section, Magellan will automatically save and advance to the next section. Table 1 (see below) shows the keys and their equivalent decimal and/or hexadecimal value.

Table 1: Decimal and Hexadecimal Values

Key Value Key Value

[1] 1 [9] 9

[2] 2 [0] 0 (decimal)

[3] 3 [1] CK* A (Hexadecimal only)

[4] 4 [2] CK* B (Hexadecimal only)

[5] 5 [3] CK* C (Hexadecimal only)

[6] 6 [4] CK* D (Hexadecimal only)

[7] 7 [5] CK* E (Hexadecimal only)

[8] 8 [6] CK* F (Hexadecimal only)

* CK = Center keypad

] or [

MAINTENANCE CODE

] you wish to program.

Space (Hexa decimal)

Feature Select Programming Method

After entering certain sections, eight options will be displayed where each option from [1] to [8] represents a specific feature or option. To manipulate the options:

• Press the key corresponding to the desired option and the option number will appear in the LCD display. This means the option is ON. Press the key again to remove the digit from the LCD display, thereby, turning OFF the option.

•Press the [*] key to set all eight options to OFF. Press the keys until the current section’s options are set. When the options are set, press the [#] key to save and advance to the next section.

•Press the [*] key twice to exit without changing any data.

Programming Using a Paradox Memory Key

The Paradox Memory Keys (PMC-3) are very useful when multiple Magellan consoles are to be programmed identically.

Rather then programming each console by entering its programming mode and then scrolling through programming sections, use a memory key to program each console. The programming of a console with a memory key takes approximately three seconds.

There are two actions that can be performed with a memory key.

Download Data to Destination Console

To download the data of a memory key into a console:

1. Remove power from the Magellan console (AC and battery)

and connect the memory key to the 5-pin connector on the left side of the back of the console (see Figure 10 on page 9).

2. Re-apply both AC and battery power to the console.

3. Press the [

data from the memory key.

Copy Data to Memory Key from Source Console

To copy the contents of a console into the memory key.

1. Remove power from the Magellan console (AC and battery)

and connect the memory key to the 5-pin connector on the left side of the back of the console (see Figure 10 on page 9).

2. Re-apply both AC and battery power to the console.

3. Press the [

begin copying its data into the memory key.

The installer code of the Magellan console used to download data to installer code programmed in the Magellan console that is to download the contents from installer codes do not match, the contents of the memory key cannot be downloaded into the receiving console.

Example: The contents of the Magellan console A will be copied into memory key B. The installer code for console A is 111111. In order to download the contents of memory key B into the Magellan console C, the installer code programmed in console C must also be 111111.

] key and Magellan will begin downloading the

] key and then the [OK] key. Magellan will

the memory key must be the same

the same memory key. If the

Paradox Magellan Systems 11

User Codes

A person must be assigned to a user code in order to have access to Magellan. A user code defines the extent of a user’s access to the system and consists of a code # (PIN) and user options. Magellan supports one Installer code, one Maintenance code and up to 16 user codes (one System Master code and 15 User codes).

Installer Code Used to program all console settings

Maintenance Code Identical to the Installer code except that

System Master Code User Code 001

15 User Codes User Codes 002 to 016

except User codes and Remote Controls

the code cannot program dialer options or perform a software reset.

Provides access to the following Magellan user features: language, voice and utility reporting, delays and tones, zone labels, system tests. Arm and disarm using any method as well as program User Codes.

Can arm and disarm the system.

User Code Length

Section [090]: Option [1] Option [1] OFF = 6-digit user codes Option [1] ON = 4-digit user codes (default)

All user codes can be set to lengths of either 4 or 6 digits. When the 4-digit option is selected, entering a 4-digit code will allow access. Using the 6-digit option, entering 6 digits is required to allow access.

If the User Code Length is changed from 4 digits to 6 digits when user codes have already been programmed, the console will automatically add the last 2 digits by using the first 2 digits. For example, if the access code is 1234 and you switch to 6 digits, the code will become 123412. Be sure to verify the access codes after switching from 4-digit to 6-digit access codes. When switching from 6 digits to 4 digits, the console will simply remove the final 2 digits of the access code. For example, 123456 will become 1234.

Maintenance Code

Section [182]; Default = 111111

The Maintenance code is similar to the Installer code. It can be used to enter the console’s programming mode (see Programming Using the Built-in Keypad on page 11), which allows you to program all features, options and commands

for the console’s communication settings (sections [100]

except

to [154]) as well as any user code. The Maintenance code can be 4 or 6 digits in length (see User Code Length on page 12) where each digit can be any value from 0 to 9.

To change the Maintenance code:

1. Access the installer programming mode (page 11).

2. Enter section [182].

3. Enter a new [4-

DIGIT MAINTENANCE CODE

1. Press [

] + [4] + [

INSTALLER CODE

] + [8] + [

NEW CODE

System Master Code

With the System Master code a user can use any arming method and can program any user’s (from 1 to 16) Access Code. The System Master code can be 4 or 6 digits in length (see User Code Length on page 12), where each digit can be any digit from 0 to 9. The System Master code cannot be changed by the installer or maintenance code, but it can be reset to default.

Lock System Master Code

Section [090]: Option [3]

Option [3] OFF =System Master code unlocked (default) Option [3] ON =System Master code locked

With section [090] option [3] enabled, the System Master code can only be changed or deleted through WinLoad or a power down reset.

Reset System Master Code

Installer Code

Section [181]; Default = 000000

The Installer code is used to enter the console's programming mode (see Programming Using the Built-in Keypad on page 11), which allows you to program all the features, options and commands of the Magellan console. The Installer code can be 4or 6-digits in length (see User Code Length on page 12) where each digit can be any value from 0 to 9. The Installer code cannot be used to program any user code.

To change the Installer code:

1. Access the installer programming mode (page 11).

2. Enter section [181].

3. Enter a new [4-

DIGIT INSTALLER CODE

1. Press [

12 Reference & Installation Manual

] + [4] + [

INSTALLER CODE

] + [8] + [

NEW CODE

Section [200]

Enter section [200] to reset the System Master code to default (1234/123456).

Make sure that the Lock System Master Code feature (section [090] option [3]) is disabled.

Duress Code

Section [090]: Option [4] Option [4] OFF = Duress code disabled (default) Option [4] ON = User code 016 becomes a duress code

With this feature enabled, user code 016 becomes a Duress code. When forced to arm or disarm their system, users can enter a Duress code (user code 016) to arm or disarm the system which can immediately transmit a silent alert to the Central Station, transmitting the duress report code programmed in section [140] (page 25).

Zone Programming

Magellan supports up to 16 wireless zones where each zone can be configured with a different zone definition and option. Each zone can also have a voice label recorded for it. Magellan’s zones can be programmed using section programming or through the Installer menu.

See Quick Setup on page 4 for more information on zone programming using the Installer menu.

Zone Programming Overview

After assigning and setting up your wireless transmitters, define the associated zone's parameters. The zone parameters define the type of zone and how the control panel will react when an alarm condition occurs on that zone. These zone parameters are programmed into one section as detailed in Figure 16 on page

13.

Figure 16: Magellan Zone Programming Overview

[001] = Zone 1 [002] = Zone 2 [003] = Zone 3 [004] = Zone 4 [005] = Zone 5 [006] = Zone 6 [007] = Zone 7 [008] = Zone 8

Zone Definition 000 = Zone disabled 001 = Entry Delay 1 002 = Entry Delay 2 003 = Follow 004 = Follow / Stay 005 = Instant 006 = Instant / Stay 007 = Instant Fire 008 = Delayed Fire Zone 009 = 24hr Burglary 010 = 24hr Hold-up 011 = 24hr Buzzer 012 = 24hr Gas 013 = 24hr Heat 014 = 24hr Water 015 = 24hr Freeze

[1] = Auto-zone Shutdown (default) [2] = Zone Bypass (default) [3] = Future use

[4] [5] Zone Alarm Type

OFF OFF Audible alarm (steady)

OFF ON Audible alarm (pulsed)

ON OFF Silent alarm

ON ON Generate report only

[6] = Intellizone [7] = Delay alarm transmission [8] = Force Zone

* Available through Section Programming only.

[009] = Zone 9 [010] = Zone 10 [011] = Zone 11 [012] = Zone 12 [013] = Zone 13 [014] = Zone 14 [015] = Zone 15 [016] = Zone 16

Zone Options*

Press and hold

the [0] key

Enter your

INSTALLER CODE

[

MAINTENANCE

[

CODE

]

Enter 3-digit

SECTION

]

[

Enter 3-digit

ZONE

[

DEFINITION

Keypad beeps twice

Use feature select

method (p. 11) to

select the [

Press the [#] key

OPTIONS

to save

]

ZONE

]

Zone Definitions

Sections [001] to [016] represent zones 1 through 16 respectively, where the first three digits in each of these sections represents the zone's definition. To disable a zone, enter 000 and then press the [#] key. There are 15 available Zone Definitions, which are described as follows:

Entry Delay 1

Sections [001] to [016]: Zones 1 to 16, 3-digit # = 001

When the system is armed and a zone defined with Entry Delay 1 opens, the console will generate an alarm after the programmed Entry Delay 1 Timer elapses. This is to provide users with enough time to enter the protected area and disarm the system. Entry Delay zones are commonly used at the entry/ exit points of the protected area (i.e. front/back door, garage, etc.). Using different Entry Delays (see Entry Delay 2 below) is useful when, for example, one entry point requires a longer delay than the other entry point.

Entry Delay 1 Timer

Section [060]: 001 to 255 seconds; 000 = Disabled; Default

= 45 seconds

Enter the desired 3-digit delay value from 000 to 255 seconds into section [060] to program the Entry Delay 1 Timer.

Entry Delay 2

Sections [001] to [016]: Zones 1 to 16, 3-digit # = 002

Entry Delay 2 zones are identical to the Entry Delay 1 zones (see Entry Delay 1 on page 13), except it uses a separate Entry Delay Timer.

Entry Delay 2 Timer

Section [061]: 001 to 255 seconds; 000 = Disabled; Default

= 45 seconds

Enter the desired 3-digit delay value from 000 to 255 seconds into section [061] to program the Entry Delay 2 Timer.

Follow Zones

Sections [001] to [016]: Zones 1 to 16, 3-digit # = 003

When an armed Follow zone opens, the console will immediately generate an alarm unless an Entry Delay zone opens first as described in the situations below:

• If an armed Follow zone opens after an Entry Delay zone opens, the console waits until the Entry Delay Timer has elapsed before generating an alarm.

• If an armed Follow zone opens after more than one Entry Delay zone opens, the console will wait until the Entry Delay Timer of the zone that opened first has elapsed.

This feature is commonly used when a motion detector is protecting the area occupied by the entry point keypad. This will prevent the motion detector from causing an alarm when a user enters through the entry point to disarm the system.

Paradox Magellan Systems 13

+ 33 hidden pages