Macrom M-DL5000 User Manual

USER MANUAL
M-DL5000
M-DL5000 User manual_ENG.indd 1 14/04/2015 17:23:35
- 1 -
Safety Precautions
Never expose this unit, amplifier, and speakers to moisture or water to prevent electric sparks or fire.
Please don't change the fuse on the power cord without professional guidance, using improper fuse may cause damage to this unit or even cause fire.
Please contact your nearest dealer if one of the following symptoms is experienced:
(a). Water or other objects enters the unit. (b). There is smoke. (c). Peculiar smell.
Only connect the unit to a 12-volt power supply with negative grounding.
Never install this unit where the operation & condition for safe driving is impaired.
Never use the video display function in the front when driving to prevent the violation of laws & regulations and also to reduce the risk of traffic accident except for using rear view video camera.
MUTE
OK
Thank you for purchasing this product. Please read through these operating instructions so you will know how to operate your model properly. After you’ve finished reading the instructions, keep this manual in a safe place for future reference.
To ensure safe driving, please adjust the volume to a safe and comfortable level in case of emergency situations.
M-DL5000 User manual_ENG.indd 1 14/04/2015 17:23:36
- 2 -
1. Never disassemble or adjust the unit without any professional guidance. For details, please consult any professional car shop / dealer for inquiry.
2. If the front panel or TFT monitor is dirty, please use a clean silicone cloth and neutral detergent to wipe off the spot. Using a rough cloth and non-neutral detergent such as alcohol for cleaning may result in scratching or decoloration to the monitor.
3. If any abnormal behavior of the unit is found, please refer to trouble shooting guide of this manual. If no relevant information is found, please press the [RESET] key on the front panel to resume factory default.
4. If you have parked the car in hot or cold weather for a long time, please wait until the temperature in the car becomes normal before operating the unit.
5. Using the car heater in low temperature environment may result in moisture inside the unit, DO NOT use the unit in this situation. Eject the disc and wipe off the moisture on the disc. If the unit still doesn't work after a few hours, please contact the service center.
6. Do not impact the LCD monitor which could cause damage.
7. To prevent damage to the screen, avoid touching it with sharp objects.
8. To provide a clear demonstration and an alternative for easy understanding to the operation of this unit, graphic illustrations are used.
However, some illustrations are different from the actual images displayed on the screen.
9. Operate the unit correctly according to this manual to prevent unnecessary problem. The guarantee won't be valid if the problem is caused by inappropriate operation.
Safety Precautions
Note: The items listed outside of the frame are the commercial products generally sold.
SD Card
Power Amplifier
Rear
Monitor
Rear vision
Monitor
Portable player
(connected via AV Input)
USB
memory
Bluetooth
cellular phone
Expanding audio feautres
Expanding visual feautres
SD
USB
MENU
NAVI
Expanding System
M-DL5000 User manual_ENG.indd 2 14/04/2015 17:23:36
- 3 -
Contents
Safety Precautions ....................................1-2
Contents ........................................................ 3
Produc overview ........................................... 4
Front Panel ............................................... 4
Remote control overview ............................. 5
Remote battery ............................................. 6
Basic Operations .......................................... 7
Detect parking brake................................ 7
Mute .......................................................... 7
Power On / Off .......................................... 7
Audible Beep Confirmation ...................... 7
Playing Source Selection ......................... 7
Audio control ................................................ 8
Adjust EQ Parameters .............................. 8
Select Preset Equalizer ............................ 8
Adjust EQ Parameters .............................. 8
Adjust FAD BAL ....................................... 8
Set Date .................................................... 9
Set Clock Mode ......................................... 9
Set Time .................................................... 9
Radio Mode ................................................. 10
Tuner TFT Display .................................. 10
Select Radio as Playing Source ............. 10
Select One Radio Band ........................... 10
Tune the radio......................................... 10
Preset Station ......................................... 11
local Seeking .......................................... 11
RDS Basics ............................................. 11
Adjust RDS Settings ............................... 11
RDS ( Radio Data System ) ..................... 12
AF Function ............................................. 12
EON ( Enhanced Other Networks ) ........ 12
TA Function ............................................. 12
CT (Clock Time) ...................................... 12
PTY Function ........................................... 12
Playback Mode ........................................... 13
Touch Screen Controls .......................... 13
Controlling Playback .............................. 13
Connect a USB Device ............................ 13
Remove a USB Device ............................ 13
Insert a SD/MMC Card ........................... 13
Remove a SD/MMC Card........................ 13
Play/Pause .............................................. 13
Previous/Next ......................................... 13
Search for a Folder ................................ 14
Repeat ..................................................... 15
Shuffle (Random) Play ............................ 15
Playback Information ............................. 16
Direct Track Entry .................................. 16
Rotate Pictures ....................................... 16
Zoom ....................................................... 16
Video Setup ............................................. 16
Bluetooth Mode .......................................... 17
Pair the Bluetooth-enabled Devices...... 17
Disconnect Bluetooth Device ................. 17
Make a Call ............................................. 17
Receive a Call ......................................... 18
Adjust Bluetooth Settings ...................... 18
Bluetooth Musci Mode ........................... 18
Settings ....................................................... 19
General settings ..................................... 19
Calibration .............................................. 19
Video settings ......................................... 19
Sound settings ........................................ 20
Time settings .......................................... 20
Language settings .................................. 20
Bluetooth settings .................................. 20
Reset ....................................................... 21
Volume settings ...................................... 21
Other Modes ............................................... 22
ther Devices ............................................ 22
Reset ....................................................... 22
Replace a Fuse ....................................... 22
Navigation (GPS) ..................................... 22
SWC Programming ................................ 22
Specifications ........................................23-24
Troubleshooting ......................................... 25
Wire Connections ....................................... 26
M-DL5000 User manual_ENG.indd 3 14/04/2015 17:23:36
- 4 -
MENU
NAVI
Front Panel
1. Internal Microphone
Internal microphone for Bluetooth calls.
2. [MENU] Button
Press to switch between the available audio/video sources applied to the unit.
3. [VOL/ / ] Knob
Rotate to adjust the volume. Press momentarily to activate the MUTE function. Press again to resume normal listening.
4. [NAVI] Button
Press to switch to navigation mode.
5. Reset Button
Press to reset system settings to factory default (except password and parental lock settings).
6. SD card slot :
nsert an SD card for playback of music/video/picture files.
7. USB por:
Connect a USB device for playback of music/video files.
8. Map Slot
The Mini SD card is used for the Navigation Map only, not for music or other files. This may be used for firmware updates if required.
9. Remote Sensor
10. [ POWER ] Button
Press to turn the unit ON. Press and hold to turn the unit OFF.
Product overview
Notice: The graphic in this manual is for reference only, and may be different from the actual unit.
1
10
8
2
3
4
5
6
7
9
M-DL5000 User manual_ENG.indd 4 14/04/2015 17:23:37
- 5 -
Front view
Remote control overview
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
31
30
1. Return to the home menu
2. Eject the disc
3. Access to tuner source
4. Access to disc source
5. Search an available radio station by decreasing tuning frequency
Select the previous chapter/track for playback
6. Select radio band
7. Zoom in (Picture menu)
Access to music list
8. Adjust screen settings
9. Open EQ menu
10. Menu cursor
11. Enter
12. Open route menu (DVD)
Turns on/off PBC (VCD)
13. Digit area
14. Repeat playback
15. Change to next source
16. Power on/off
17. Access to Bluetooth source
18. Access to navigation source
19. Pause playback/Start playback
20. Search an available radio station by increasing tuning frequency
Select the next chapter/track for playback
21. Playback disc in different angle for a scene (DVD)
Rotate (photo playing) Access to video list
22. Language selection for subtitle (DVD)
Access to photo list
23. Change the audio language for disc playback (DVD)
24. Increase/Decrease volume
25. Access to settings source
26. Mute on/ off audio output
27. Activate direct access mode
28. Dial/Receive a call
29. Hang up
30. Play all chapter/tracks in random order
31. Press to clear the number one by one
Hold to clear all the numbers
Note: The following keys 2,4,7,21,22,23, are for the disccontrol function. Ignore these keys to the 'M-DL5000.
M-DL5000 User manual_ENG.indd 5 14/04/2015 17:23:38
- 6 -
Notes of remote control using
1) Aim the remote control at the remote sensor on the unit.
2) Remove the battery from the remote control or insert a battery insulator if the battery has not been used for a month or longer.
3) DO NOT store the remote control under direct sunlight or in high temperature environment, or it may not function properly.
4) The battery can work for 6 months under normal condition. If the remote control can't work, please change the battery.
5) Use“button shaped” lithium battery“CR2025”(3V) only.
6) DO NOT recharge, disassemble, heat or expose the battery in fire.
7) Insert the battery in proper direction according to the ( + ) and ( - ) poles.
8) Store the battery in a place where children cannot reach to avoid the risk of accident
PU LL O UT PU SH I N
Remote battery
Uninstall Battery Slide out the battery compartment tray at the bottom on the back of the remote control.
Install Battery Use button-shaped lithium battery CR2025 (3V)” only. Insert the battery to the battery tray with proper direction according to the (+) and (-) poles.
Back view
M-DL5000 User manual_ENG.indd 6 14/04/2015 17:23:38
- 7 -
Detect parking brake
• Connect the cable "BRAKE" to the parking brake switch to view video files on the TFT monitor. Engage the parking brake for viewing videos.
• Whenthe parkingbrakeisnotengaged, themonitor displays"Warning!!!,Videoplayback is
disabled for your safety. Engage parking brake to watch video.", preventing the driver to watch content while driving. The rear screens are not interested in this inhibition.
Mute
Press [
VOL/ /
] knob to mute the volume from the unit. Press again to restore the volume. [
] is displayed on the LCD. Adjusting the volume or using any of the audio setup features cancels
the mute function.
Power On / Off
Press the [
VOL/ /
] knob on the unit to turn the unit on. The buttons on the front of the unit light up for a moment and the current mode status appears in the LCD. Press and hold the [
VOL/ /
] knob to power off the unit.
Audible Beep Confirmation
An audible beep tone confirms each function selection. The Beep tone can be disabled through the Setup menu.
Playing Source Selection
Press the [ MENU ] button on the front panel to change between available playing sources. The playing mode is displayed on the screen.
1. 1/2 or 2/2: Touch this page button to view the first or second page of on-screen buttons
2. Function icons
3. Clock
4. Touch for quick access to Equalizer level settings
Basic Operations
1
2
3 4
1
M-DL5000 User manual_ENG.indd 7 14/04/2015 17:23:39
- 8 -
Select Preset Equalizer
1. Enter the EQ setup mode Touch the [ ] icon in the user interface and the EQ setup interface will display on the screen.
2. Select EQ mode Touch the desired EQ selection: [ Optional ] / [ Classic ] / [ Rock ] / [ Jazz ] / [ Techno ] / [ Pop ],
and the EQ mode will change.
Adjust EQ Parameters
To adjust EQ parameters, touch and drag the parameters adjustment bar. [ User ]: Set the desired audio effect.
[ Flat ]: Select the original audio effect. [ Reset ]: Cancel the equalizer function settings. [ Loud: On/Off ]: When listening to music at low volumes, this featurewill selectively boost certain bass and treble frequencies.
Adjust FAD BAL
You can adjust front/back/left/right balance of the speaker and the subwoofer volume to get balanced listening effect according to the surroundings and your interest.
1. Enter the EQ setup mode Touch the [ ] icon in the user interface and the EQ
setup interface will display on the screen.
2. Adjust subwoofer volume Touch [ ] / [ ] or drag [ ] to adjust subwoofer
volume from -12 to +12.
3. Adjust fader / balance value Touch [ ] / [ ] / [ ] / [ ] to adjust fader /
balance value from -20 to +20. [ ]: Front speaker [ ]: Rear speaker [ ]: Left speaker [ ]: Right speaker
Audio control
EQ Menu
The Audio Control feature allows you to easily adjust your audio system to meet the acoustical characteristics of your vehicle, which vary depending on the type of vehicle and its measurements. Proper setting of the Fader and Balance boosts the effects of the cabin equalizer.
Notes:
1. The parameters of the EQ modes has been preset and you can not change them besides ‘User’.
2. The EQ mode will change to ‘User’ automatically when you adjust the frequency value under the
modes besides ‘User’.
3. The value of Sub is independent of EQ mode and can be adjusted separately.
M-DL5000 User manual_ENG.indd 8 14/04/2015 17:23:41
- 9 -
Setting Date /Time
1. Touch [ Settings].
2. Touch [ Time ]. The date/time setup menu is displayed.
Set Date
1. Touch [ Date ].
2. Touch the date information on the screen . A submenu is displayed.
3. Touch [ ] or [ ] to set year, month and day.
Set Clock Mode
1. Touch [Clock mode].
2. Touch [12Hr] or [24Hr] to switch clock mode.
Set Time
1. Touch [ Time ].
2. Touch the time on the screen, a submenu is displayed.
3. Touch [ ] or [ ] to set hour and minute.
M-DL5000 User manual_ENG.indd 9 14/04/2015 17:23:42
- 10 -
Select Radio as Playing Source
Open the Source Menu and then touch [Radio].
Select One Radio Band
Touch the [ ] icon on the user interface to select one radio band among FM1, FM2, FM3, AM1 and AM2.
Tune the radio
Auto Tunig During auto tuning, the frequency will be changed in seek mode. Touch the [ ] / [ ] icon on the user interface to tune in a higher / lower station. Note: When a station is received, searching stops and the station is played.
Manual Tuning Method 1: Touch and hold [ ] / [ ] icon on the user interface more than 1 second to changed in steps higher / lower station. Repeat the operation to change step by step.
Method 2:
1. Touch the numeric keypad icon [ ]. Numeric keyboard is displayed, touch number to
input frequency.
2. Touch [ ] to delete the input number step by step.
3. Touch [ OK ] to enter.
Radio Mode
1. Touch to view the MENU and select a new playback source
2. Strong Local signal broadcasting indicator
3. Stereo broadcasting indicator
4. Current radio band indicator
5. Broadcaster information stored at the preset
6. Touch to view more on-screen buttons
7. Touch to seek backward
8. Touch for quick access to EQ level settings
9. Touch to seek forward
10. Touch to change between AM/FM bands
11. Clock
12. Current preset radio station
13. Current radio information
14. AF: Alternative Frequency indicator
15. TA: Traffic Announcement indicator
16. RDS setting options
17. Save the desired radio station
18. Touch to change between Local and Distance
19. Enter frequency directly
20. Search stations automatically
Tuner TFT Display
1 2 3 4
11
12
13
14
15
5
6
7 8 9 10
TA
16 17 18 19
20
M-DL5000 User manual_ENG.indd 10 14/04/2015 17:23:43
- 11 -
Local Seeking
Touch the [ ] icon and choose the Radio Local or Distance. When the [ ] icon turns bright, only stations with a strong signal strength will be detected .
Default is “Distance”.
EQ Selection
Press the [ ] icon and enter the EQ setup.
RDS Basics
RDS transmits data to the radio which displays information such as name station, song artist, and song title. RDS service availability varies with areas.
Adjust RDS Settings
1. In Radio menu, touch [ ].
The option menu is displayed.
2. Touch on the selected option to change the setting.
[RDS]: To turn on or off “RDS” function. [CT]: To turn on or off “Clock Time” synchronization function. [EON]: To turn on or off “EON” function. [TA]: To turn on or off “TA” function. [PTY]: To show PTY list. [ VOL]: Touch [ ] / [ ] to adjust TA volume.
Radio Mode
Preset Station
The unit has 5 bands, such as FM1, FM2, FM3, AM1, AM2, and each band can store 6 stations; the unit can store 30 stations in total.
Search Stations Automatically Touch [ ] to search station and store 6 strongest stations in current band automatically.
Manual Store
1. Tune to a station.
2. Touch [ ].
3. Touch one of the channels P1 to P6 to save the select band.
Tune to a Preset Station
1. Touch [Radio].
2. Select a band (if needed).
3. Touch one of the preset channels (P1 to P6) on the screen.
M-DL5000 User manual_ENG.indd 11 14/04/2015 17:23:44
- 12 -
RDS ( Radio Data System )
The unit provides basic functions of RDS. RDS service availability varies with areas. Please verify if RDS service is available in your area.
AF Function
Alternative Frequencies Lists are used in conjunction with the PI code (Program Identification code)to assist automatic tuning. Using this information, the radio can automatically search out another frequency of the same station.
Note:
• Duringautoswitchingradiofrequency,someinterferencemaybeheard..
• TurningoffAFfunctioncansettlethisproblem.
EON ( Enhanced Other Networks )
When EON data is received, the EON indicator lights and the TA and AF functions are enhanced. TA: Traffic information can be received from the current station or stations in other network. AF: The frequency list of preset RDS stations is updated by EON data. EON enables the radio to make fuller use of RDS information. It constantly updates the AF list of preset stations, including the one that currently tuned into.
TA Function
The TA (Traffic Announcement) function lets the unit receive traffic announcements automatically. The TA function can be activated by a TP (Traffic Program) station broadcasting traffic information. When TA is activated and a traffic announcement is received, the current playing source will be overridden by the traffic announcement The unit returns to the original source after the traffic announcement has been received.
CT (Clock Time)
Some stations broadcast the time and date within the encoded RDS signal. The clock time is automatically adjusted when ‘CT’ is set to ‘ON’.
PTY Function
PTY is an abbreviation for the type of program defined by a code to define the program being broadcast (eg news or Rock). The Options of PTY is displayed on the screen. To see the options PTY, tap the scroll bar and arrows on the screen. When an option is selected PTY (eg News), the radio unit, the PTY search available. If the PTY requested was not found, the unit returns to the original radio frequency.
Radio Mode
M-DL5000 User manual_ENG.indd 12 14/04/2015 17:23:44
- 13 -
Touch Screen Controls
The touch key areas for playback are outlined below: A: Return to the main menu B: Play the video and display playback information C: Display onscreen control menu D: Time display
Controlling Playback
To access the on-screen controls, touch the screen except upper left corner, and touch again to cancel display. Touch [ ] to view all function icons.
Connect a USB Device
1. Open the USB door.
2. Insert the small end of the USB cable to mini USB socket, then connect the other end of the cable to your USB device.
Remove a USB Device
1. Select other source on the main menu.
2. Remove the USB device.
Insert a SD/MMC Card
1. Open SD/MMC card cover.
2. Insert the SD/MMC card into the SD/MMC card slot.
Play starts automatically.
Remove a SD/MMC Card
1. Select other source on the main menu.
2. Press the SD card to remove it.
Play/Pause
1. Once USB or SD/MMC card is inserted, play starts automatically.
For movie, if a menu appears, press [ ] to start play.
2. To pause, touch [ ].
To resume play, touch [ ].
3. Skip to previous / next track / chapter, press [ ] / [ ] key.
Previous/Next
Touch [ ] / [ ] key on the screen to skip to previous / next track / chapter.
Playback Mode
B
C
A
M-DL5000 User manual_ENG.indd 13 14/04/2015 17:23:44
- 14 -
Search for a Folder
For Audio Files
1. Touch [ ] to display all available audio folders.
2. Touch a folder,then touch the desired file.
3. Touch the file again to start play.
For Video Files
1. Touch [ ] to display all available video folders.
2. Touch a folder,then touch the desired file.
3. Touch the file again to start play.
For Picture Files
1. Touch [ ] to display all available picture folders
2. Touch a folder,then touch the desired file.
3. Touch the file again to start play.
For Folder Control
1. Touch [ ] to display all available folders
2. Touch a folder,then touch the desired file.
3. Touch the file again to start play
Playback Mode
M-DL5000 User manual_ENG.indd 14 14/04/2015 17:23:45
- 15 -
Repeat
For MP3/WMA files:
1. Touch anywhere except the upper left corner to display menu on the screen.
2. Touch [ ] repeatedly:
[ 1 ] Repeat single: Play the current single repeatedly. [ ] Repeat all: Play all in the all repeatedly. [ ] Repeat off: Cancel repeat play.
Shuffle (Random) Play
You can play audio tracks/files in random order.
1. Touch the screen to display control menu, if necessary.
2. Touch [ ] to display the 2nd menu, if necessary.
3. Touch [ ] on the screen repeatedly to turn random play on or off.
Playback Mode
M-DL5000 User manual_ENG.indd 15 14/04/2015 17:23:45
- 16 -
Playback Information
For USB/SD
1. Device type.
2. Track information. “1/2” indicates that
this USB has 2 tracks and the track playing back now is the first title.
Elapsed Time
1. Elapsed time of the current track.
2. Total time of the current track.
Direct Track Entry
To select a track directly, touch the [ ] icon on screen control to display the direct entry menu. Enter the desired track using the on-
screen number pad. Press [ OK ] to the selected track.
Rotate Pictures
1. When you view pictures, touch the screen to display menu on the screen, if necessary.
2. Touch [ ] to display the 2nd menu.
3. Touch [ ] repeatedly to rotate the picture.
Zoom
You can zoom in pictures for a close view.
1. When you view pictures, touch the screen to display menu on the screen, if necessary.
2. Touch [ ] to display the 2nd menu.
3. Touch [ ] repeatedly to zoom in the picture.
Video Setup
Touch [ ] to access video setup mode, touch [ ] or [ ] to set the desired effect.
Playback Mode
00:01:20 00:30:17
1
2
M-DL5000 User manual_ENG.indd 16 14/04/2015 17:23:46
- 17 -
You can make or receive phone calls with Bluetooth-enabled phones through the unit. You can also listen to music from a Bluetooth-enabled device.
Bluetooth Mode
Pair the Bluetooth-enabled Devices
To connect your Bluetooth device to the unit, you need to pair the device to the unit. Pairing needs only to be done once. You can pair up to five devices.
1. Turn on the Bluetooth function on the device.
2. Touch [ ] to search for Bluetooth device with the unit.
3. Start scanning on the Bluetooth device and select the
unit “M-DL5000”
4. Enter default password “0000”.
Tip:
• TheoperationalrangebetweenthisunitandaBluetoothdeviceisapproximately5meters.
• Before you connecta Bluetooth device tothis unit, familiarize yourself with theBluetooth
capabilities of the device.
• CompatibilitywithallBluetoothdeviceisnotguaranteed.
• AnyobstaclebetweenthisunitandaBluetoothdevicecanreducetheoperationalrange.
• Keepthisunitawayfromanyotherelectronicdevicethatmaycauseinterference.
Disconnect Bluetooth Device
To disconnect one device, touch [ ] .
Tip
• Thedevicewillalsobedisconnectedwhenthedeviceismovedbeyondtheoperationalrange.
• Ifyouwanttoreconnectthedevicetotheunit,placeitwithintheoperationalrange.
• Ifyoudonotwanttoreconnectthedevicetotheunitautomatically,touch[ ],
then set [ Auto connect ] to [ Off ]. For details, see the “Adjust Bluetooth Settings” section.
Make a Call
1. Select Bluetooth function in the home menu.
2. Pair the phone with the unit.
3. Search for phone number from the following list:
[Phone Book] [Call Log] [Missed calls] [Received calls] [Dialed calls]
Or touch the number pad directly, then touch [ ] to dial.
M-DL5000 User manual_ENG.indd 17 14/04/2015 17:23:48
- 18 -
Receive a Call
By default, all incoming calls are received automaticaly.
1. If there is an incoming call, the screen will appear “Incoming”.
2. You may touch the screen to select [ hang up ] or
[ Answer ].
Bluetooth Mode
Tip
• Youcanselecttoreceivecallsmanuallybyset[Autoanswer]to[Off]status.
Adjust Bluetooth Settings
1. In Bluetooth menu,touch [ ].
The option menu is displayed.
2. Touch on the selected option to change the setting.
∙[Bluetooth]:Toturnonoroff“Bluetooth”function. ∙[Autoconnect]:Toturnonoroff“Autoconnect”function. ∙[Autoanswer]:Toturnonoroff“Autoanswer”function. ∙[Pairingcode]:Tosetparingcode.
∙[Phonebooksync]:Tosynchronizephonebook,touch
[ OK ] on the sub-menu popped out. Phonebook sync may take several minutes to load on initial setup.
Tip
• YoucanalsoadjustBluetoothsettingsinthe“Settings”menu.
Bluetooth Music Mode
A2DP
A2DP is short for Advanced Audio Distribution Profile. The mobile phones supporting this function can transmit stereo audio, whereas the ones not supporting this function can transmit mono audio only.
AVRCP
AVRCP is short for Audio/Video Remote Control Profile. The mobile phones supporting this function can control the playback of a Bluetooth audio player.
In the mode of the music player working, if you want to make a phone call, you can press the number keys on the mobile phone. At the same time the music player will stop. The TFT screen will display “Calling”, after the call received, the voice will be transferred to the unit. When the call ends, the screen will display music playing menu. If there is an incoming phone call, the music player will stop, and the screen will display “Incoming”. When the call ends, the screen will display music playing menu.
M-DL5000 User manual_ENG.indd 18 14/04/2015 17:23:52
- 19 -
General Settings
1. Touch [ General ] in the settings page.
2. Touch to highlight a setting.
3. Touch on the option to display/select an option.
4. Touch [ ] or press the Menu button on the front panel to exit.
General settings Options Description
Radio region
USA
Select one that matches your location.
China
Japan
Europe
Europe (LW)
OIRT
Radio range
Local
Distance
Blackout Off/10s/20s
Dimmer mode Low/Medium/Normal/High Adjust the display brightness.
Beep
On
Turn on the beep sound. Each time you press a button, the unit beeps.
Off Turn off the beep sound.
Calibration Start Calibrate the touch screen.
Calibration
When the touch operation is not sensitive or valid, you should calibrate the touch screen through calibration setting function. Adjust the response positions of the touch panel as followings:
1. Press the [ Calibration ] option on the setup menu to enter.
2. Touch [ Start ] to enter.
3. Aim at center of [ + ], follow the path as shown of the figure, after steps from 1 to 5, touch anywhere on the screen to save and exit from calibration. Or wait for 30 seconds to exit without making changes.
Video Settings
1. Touch [Video].
2. Touch an option repeatedly to select:
3. Touch [ ] or press the Menu button on the front panel to exit.
Video settings Options Description
Detect parking brake
On Disable video
Off Enable video
Whendetect parkingbrakeis set to“On”,thescreen willdisplay[ Warning!!!”Video playbackis
disabled for your safety. Engage parking brake to watch video] The above warning screen will prevent the driver watching images.
Settings
M-DL5000 User manual_ENG.indd 19 14/04/2015 17:23:53
- 20 -
Sound settings
1. Touch [Sound].
2. Touch an option repeatedly to select:
3. Touch [ ] or press the Menu button on the front panel to exit.
Sound settings Options Description
Subwoofer
On Turn on the subwoofer.
Off Turn off the subwoofer
Subwoofer filter
80Hz
Select subwoofer filter criteria.120Hz
160Hz
Time settings
1. Touch [ Time ].
2. Touch an option repeatedly to select:
3. Touch [ ] or press the Menu button on the front panel to exit.
Time settings Options Description
Date Y/M/D
Touch [ ] or [ ] to set year, month and day.
Clock 12Hr/24Hr Touch [12Hr] or [24Hr] to switch clock mode.
Time
H / M/ A M/ PM
Touch [ ] or [ ] to set hour and minute. Touch [ ] or [ ] to set AM/PM (only for 12Hr).
Language settings
1. Touch [Language].
2. Touch an option repeatedly to select.
3.
Touch [ ] or press the Menu button on the front panel to exit.
Language settings Description
OSD Select on-screen display language.
Bluetooth settings
1. Touch [Bluetooth].
2. Touch an option repeatedly to select.
3.
Touch [ ] or press the Menu button on the front panel to exit.
Bluetooth settings Options Description/Note
Bluetooth
On Turn on the Bluetooth function.
Off Turn off the Bluetooth function.
Auto connect
On
If the pre-paired device is within the effective range, the unit re-connects to pre-paired device automatically.
Off Need to re-connect manually.
Auto answer
On Answer paired phone call automatically.
Off Answer phone call manually.
Pairing code Set the password for pairing the unit with other Bluetooth device.
Microphone Internal or External
Before setting, make sure that the external microphone is installed.
Settings
M-DL5000 User manual_ENG.indd 20 14/04/2015 17:23:53
- 21 -
Reset
1. Touch [Reset].
2. Touch an option repeatedly to select.
3.
Touch [ ] or press the Menu button on the front panel to exit.
Reset settings Option Description
Load Factory Reset Restore to default settings.
Volume settings
You can set different volume for different modes.
1. Touch [Volume].
2. Touch on a source.
[F-USB] [AV-IN] [SDHC] [Navigation] [Radio] [R-USB] [Bluetooth]
3. Touch [ ] or [ ] to assign value: -6 to 6.
When switching to the source, the volume increases or decreases automatically.
4. Touch [ ] or press the Menu button on the front panel to exit.
Settings
M-DL5000 User manual_ENG.indd 21 14/04/2015 17:23:53
- 22 -
MENU
NAVI
Other Devices
You can connect an external audio/video device to the unit.
1. Connect the external device with the supplied AV cable.
2. Touch the upper left corner to display the main menu.
3. Touch [ AV-IN ] to access external device.
Reset
When the unit hangs up, you can reset it. Press [ RESET ] with a ball-point pen or similar tool.
Tip: When the unit has been reset, all the settings will return to default settings.
Replace a Fuse
If there is no power, the fuse may be damaged and need to be replaced.
1. Take out the unit from dashbpard.
2. Check all electrical connections.
3. Buy a fuse that matches the amperage of the damaged fuse.
4. Replace the fuse while the units power is disconnected.
Navigation (GPS)
1. Touch the upper left corner to display home menu.
2. Touch [Navigation], to start the navigation software.
3. For instructions on using of navigator, refer to the manufacturer’s user manual.
Nota: While Navigation is running, you can view the previously selected source by holding the [MENU] button. Press again and hold the [MENU] button to return to the navigation mode. Where it was used the Bluetooth function you can display the navigation following the procedure described above.
Other Modes
Reset
Steering Wheel Control Programming
1. Touch the upper left corner to display home menu.
2. Touch [ SWC ], the SWC menu will display.
3. Select the keys corresponding to the functions of steering wheel controls by tapping the KEY and
define the desired function.
4. Touch [ Pair ] to program.
5. Press each individual steering wheel control button for each corresponding function.
6. Once the final steering wheel control button is programmed, the functions are saved and the
programming will end.
7. Touch [ Reset ] to reset the programming.
M-DL5000 User manual_ENG.indd 22 14/04/2015 17:23:54
- 23 -
GENERAL
Reference Supply Voltage ....................................................................................................... 12V(DC)
Operating Voltage Range ...........................................................................................10.5 - 15.8V(DC)
Max Operating Current ................................................................................................................... 15A
Grounding System ..................................................................................... Car Battery Negative Pole
Dimensions(WXHXD) .......................................................................................... 178X101.5X160.5mm
Weight(main unit) ...................................................................................................................... 1.28kg
FM
Signal Noise Ratio ....................................................................................................................≥55dB
Residual Noise Sensitivity (S/N=30dB) ..................................................................................18dBμV
Frequency Response (±3dB) ...................................................................................... 20Hz~12.5KHz
Station Seeking Level .......................................................................................................20~28dBμV
Distortion ..................................................................................................................................≤1.0%
Stereo Separation (1KHz) .........................................................................................................≥25dB
Antenna Impedance ......................................................................................................................75
Ω
AM
Residual Noise Sensitivity (S/N=20dB) ..................................................................................30dBμV
Selectivity (±9KHz) ....................................................................................................................≥50dB
LCD
Screen size ................................................................................................................ 6.2 inches(16:9)
Display resolution .......................................................................................................... 800X480dots
Contrast radio ............................................................................................................................... 400
Brightness .......................................................................................................................... 280cd/m2
OUTPUT
Distortion (line out) ...................................................................................................................≤0.1%
Frequency Response (±3dB) ......................................................................................... 20Hz~20KHz
Maximum Output Power .......................................................................................................... 4×45W
Load Impedance ............................................................................................................................ 4
Ω
AUX IN
Distortion ..................................................................................................................................≤0.5%
Frequency Response (±3dB) ......................................................................................... 20Hz~20KHz
Audio Input Level ......................................................................................................................1Vrms
Audio
Audio Output Impedance ............................................................................................................100
Ω
Audio Output Level ..........................................................................................................2Vrms(Max)
Video
Normal Video Input Level (CVBS) .........................................................................................1.0±0.2V
Video Input Impedance .................................................................................................................75
Ω
Video Output Impedance ..............................................................................................................75
Ω
Video Output Level .................................................................................................................1.0±0.2V
Environment
Operating Temperature ...............................................................................................-10°C ~ +60°C
Storing Temperature ...................................................................................................-20°C ~ +70°C
Operating Humidity ........................................................................................................ 45%~80%RH
Storing Humidity ............................................................................................................ 30%~90%RH
Notice: When the unit is operated to extremes, such as with maximum power output for a long time, or the temperature is over 70°C, it will enter heat protection mode, the volume will be reduced automatically. This is normal.
Specifications
M-DL5000 User manual_ENG.indd 23 14/04/2015 17:23:54
- 24 -
Supported Formats:
• USBormemoryfileformat:FAT16,FAT32
• Mp3bitrate(daterate):32-320Kbpsandvariablebitrate
• Directorynestinguptoamaximumof8levels
• Numberofalbums/folders:maximum99
• Numberoftracks/titles:maximum999
• ID3tagv2.0orlater
• FilenameinUnicodeUTF8(maximumlength:128bytes)
Unsupported Formates:
• Emptyalbums:anemptyalbumisanalbumthatdoesnotcontainMP3files,andisnotbeshown
in the display.
• Unsupportedfileformatsareskipped.Forexample,Worddocuments(.doc)or
Mp3 files with extension.dlf are ignored and not played.
• AAC,WMV,PCMaudiofiles
•DRMprotectedWMAfiles(.wav,.m4a,.m4p,.mp4,.aac)
•WMAfilesinLosslessformat
Supported MP3 format:
• ISO9660,Joliet
• Maximumtitlenumber:512(dependingonfilenamelength)
• Maximumalbumnumber:255
• Supportedsamplingfrequencies:32kHz,44.1kHz,48kHz
• SupportedBit-rates:32-320Kbpsandvariablebitrate
Supported Video Formats:
• MP3
• DivX
Specifications
M-DL5000 User manual_ENG.indd 24 14/04/2015 17:23:54
- 25 -
Troubleshooting
What appears to be trouble is not always serious. Please check the following points before calling a service center.
Problem Cause Corrective action
General
Unit can not power on
Unit fuse blown. Install new fuse with correct rating.
Car battery fuse blown. Install new fuse with correct rating.
Illegal operation Reset the unit.
No/low audio output
Improper audio output connection. Check wiring and correct.
Volume set too low. Increase volume level.
Speakers damaged. Replace speakers.
Heavily biased volume balance.
Adjust the channel balance to center position.
Speaker wiring is in contact with metal part of car.
Insulate all speaker wiring connections.
Poor sound quality or distortion
Pirated disc is in use. Use original disc.
Speaker power rating does not match unit. Replace speakers.
Wrong connections. Check wiring and correct.
Speaker is shorted. Check wiring and correct.
Unit resets itself when engine is off
Incorrect connection between ACC and BATT. Check wiring and correct.
TFT monitor
Warning information is shown at all times
Parking break wiring is not correct. Check wiring and correct.
Flashing image or interference appears on screen
The color system of DVD disc does not match the monitor.
Adjust the color system of the DVD disc playing back or the monitor in use.
Pirated disc is in use. Use original disc.
Video cable damaged. Replace cables.
Improper video signal connections. Check wiring and correct.
M-DL5000 User manual_ENG.indd 25 14/04/2015 17:23:54
- 26 -
Wire Connections
Rear right (+) / Purple
Rear right (-) / Purple with black stripe
Front right / Gray
Front right (-) / Gray with black stripe
Front left (+) / White
Front left (-) / White with black stripe
ACC+ / Red
Rear left (+) / Green
Ground / Black
Battery 12V(+) / Yellow
Rear left (-) / Green with black stripe
Function
Connector A Connector B
PIN NO.
Illumination / Orange
Antenna-Power Control/ Blue
Steering Wheel Control
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
Radio Antenna
Antenna GPS
MIC
R USB
VIDEO
CAMERA 
VIDEO
OUT
AV Input REAR FRONT
SUB OUT
M-DL5000 User manual_ENG.indd 26 14/04/2015 17:23:55
The BLUETOOTH ® world mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by ALDINET S.p.A. is under license.
The MACROM brand is a registered trade mark of ALDINET S.p.A.
Declaration of Conformity
ALDINET S.p.A
Viale C. Colombo, 8 - 20090 Trezzano s/N (MI) - Itlaly Tel. +39 02 484781
w w w . m a c r o m . i t
M-DL5000 User manual_ENG.indd 27 14/04/2015 17:23:55
Loading...