Lorex LKB353A Series Quick Start Manual

Resources

• You can use a RJ45 coupler or switch (not included) to connect male ends
of Ethernet cable together.

• To extend the cable run beyond 300ft (92m), a switch will be required (sold
separately).

LKB353A_QSG_EN_R1

5MP HD IP Bullet Security Camera with Audio

• 5MP HD IP Bullet Security Camera with Audio

• Mounting Kit*

• Ethernet Extension Cable*

• Weatherproofing Cap*

• Allen Key*

• Read this guide carefully and keep it for future reference.

• Follow all instructions for safe use of the product and handle with care.

• Use the camera within given temperature, humidity and voltage levels noted in the
camera’s specifications.

• Do not disassemble the camera.

• Do not point the camera directly towards the sun or a source of intense light.

• Use only the supplied regulated power supply provided with the product. Use of a non­regulated, non-conforming power supply can damage the product and void the warranty.

• Periodic cleaning may be required. Use a damp cloth only. Do not use any harsh, chemical­based cleaners.

• The supplied cable is rated for surface mounting only. Cables for in-wall and floor-to­floor installations are sold separately (CMR type). These and other cables are available at

lorextechnology.com

* Per camera in multi-camera packs.

Copyright © 2017 Lorex Corporation
As our products are subject to continuous improvement, Lorex reserves the right to
modify product design, specifications and prices, without notice and without
incurring any obligation. E&OE. All rights reserved.

Quick Start Guide

English Version 1.0

LKB353A SERIES

Package Contents

ATTENTION:

It is recommended to connect the camera to the NVR or an external PoE
switch. If using a DC power adapter (not included) with the camera, a
REGULATED power supply is REQUIRED for use with this camera. Use of
a non-regulated, non-conforming power supply can damage this product
and voids the warranty.

Safety Precautions

Dimensions

6.1” / 154mm

2.7” / 69mm

Need Help?

Visit us online for up-to-date software and complete instruction manuals

Click on the Downloads tab

4

Visit lorextechnology.com

Search for the model number

of your product

Click on your product in the

search results

3

2

1

www.lorextechnology.com

Extend the cable run for your camera. Additional extension cables sold
separately. See table below:

Cable Extension Options

Cable Type

Max Cable Run

Distance

Max # of

Extensions

CAT5e (or higher) Ethernet cable 300ft (92m) 3

• For a full list of compatible recorders, visit lorextechnology.com/compatibility

• Not intended for submersion in water. Installation in a sheltered location

recommended.

Disclaimers

Audio Settings

ATTENTION:

Audio recording without consent is illegal in certain jurisdictions. Lorex Corporation
assumes no liability for use of its products that does not conform with local laws.

Audio is disabled by default. If needed, you can enable audio
through a Lorex NVR.

NOTE: These instructions are based on current NVR interface. For the most up-to-

date instructions, see your NVR’s instruction manual on www.lorextechnology.com.

To enable camera audio:

1. In Live View, right-click anywhere on the screen to open the Quick Menu.

2. Click Main Menu. If prompted, enter the system user name and password.

3. Under Settings on the left-side panel, click Record, then click the Mainstream
tab.

4. Select a channel where an audio camera is connected next to Channel.

5. Check the Audio checkbox to enable audio. Click Save to apply changes.

6. Repeat steps 4 and 5 for any other audio cameras you want to enable audio for.

7. (Optional) Click the Substream tab and perform the same steps to enable audio
when viewing cameras through the computer or mobile applications.

Microphone

Connecting the Cameras

• Point the camera where there is the least amount of obstructions (i.e., tree
branches).

• Install the camera where vandals cannot easily reach.

• Secure cabling so that it is not exposed or easily cut.

• This camera is rated for outdoor use. Installation in a sheltered location is
recommended.

Installation Tips

To install your camera:

1. Set the camera in the desired mounting position and mark holes for
screws through the camera base.

2. Drill the holes, then feed the cable through the mounting surface or
cable notch.

NOTE: Insert the included drywall anchors if you are mounting the

camera onto drywall.

3. Connect cables as shown in the section “Connecting the Camera”.

4. Mount the camera stand to the mounting surface using the provided
screws. Make sure all screws are fastened tightly.

5. Adjust the camera as shown below:

Installing the Camera

Connect the Ethernet cable to
the camera.

Connect the other end of the
Ethernet cable to the NVR’s PoE
ports. The camera may take a
minute to power up after
being connected.

Connecting the Camera

Cable Notch

LKB353A_QSG_EN_R1

A. ROTATING THE ARM: Use the included Allen key to loosen the
adjustment screw closest to the camera base. Rotate the arm of the
camera as needed, then tighten the screw.

B. BENDING THE ARM: Use the Allen key to loosen the middle
adjustment screw. Bend the arm of the camera up to 90°, then
tighten the screw.

C. LEVELING THE CAMERA: Use the Allen key to loosen the
adjustment screw furthest from the camera base. Rotate the camera
until it is level with the viewing area, then tighten the screw.

ATTENTION:

Test your camera prior to selecting a permanent mounting location by
temporarily connecting the camera and cable to your NVR.

Before Installing the Camera

• Decide whether to run the cables

through the wall / ceiling (drilling
required) or along the wall / ceiling.

• If you run the cables along the

wall / ceiling, you must run the
cable through the cable notch on
the base. This will keep the camera
base flush to the surface when mounted.

A B C

ATTENTION:

This camera includes an Auto Mechanical IR Cut Filter. When the camera
changes between Day/Night viewing modes, an audible clicking noise may
be heard from the camera. This clicking is normal, and indicates that the
camera filter is working.

Connect the other end of the
Ethernet cable to a router or
switch on your network. See
your NVR manual for details on
connecting the camera to your
NVR using a switch or router.

Camera

NVR

Setup Diagram

CameraHD NVR

Scenario 1: Connect Cameras to NVR

Scenario 2: Connect Cameras to Local Area Network (LAN)

Router

Camera

HD NVR

Router

PoE Switch

OR

(Optional)

12V DC Power

ATTENTION:

This camera is only compatible with select NVRs. For a list of compatible
recorders, visit lorextechnology.com/compatibility.

Ethernet Cable

NOTES:

• For weatherproofing instructions,
see “Using the Weatherproofing
Cap (Optional)”.

• A 12V DC power adapter (model#:
CVA4902, not included) is
only required if connecting the
camera’s Ethernet cable to a
router or switch that does not
support PoE.

Problem Solution

No picture / signal • Ensure the camera is connected to a compatible NVR.

For full camera compatibility, visit lorextechnology.com/

compatibility.

• The camera may take up to 1 minute to power up after
being connected to the NVR. Wait two minutes before
following the steps below.

• Ensure the camera is connected to your NVR or to your
local network.

• If you are not using PoE, you must connect the camera
to a 12V DC power adapter (not included).

• If the camera is connected to the LAN, you must search
your network for cameras using the NVR. See the NVR’s
instruction manual.

• Ensure your NVR is properly connected to a TV/monitor.

• There may be an issue with your extension cable run.
Connect the camera to the NVR using a different
Ethernet cable.

Picture is too bright • Ensure your camera isn’t pointed directly at a source of

light (e.g., sun or spot light).

• Move your camera to a different location.

• Check the brightness and contrast settings on the NVR.

Picture is too dark • Check the brightness and contrast settings on the NVR.

Night vision is not
working

• The night vision activates when light levels drop. The
area may have too much light.

Picture is not clear • Check the camera lens for dirt, dust, spiderwebs. Clean

the lens with a soft, clean cloth.

• Make sure that the cable run is within the limitations
specified in the section ‘Cable Extension Options’.

Bright spot in
video when viewing
camera at night

• Night vision reflects when pointing a camera through a
window. Move the camera to a different location.

Picture is in color in
dark conditions

• This camera comes with an image sensor that is extra
sensitive to light, meaning that the camera stays in
color mode at low-light conditions. For instructions on
how to make your camera switch to night mode, visit

lorextechnology.com, and search for “How do I make my

camera switch to night mode?”

No audio

• Audio is only supported on Lorex HD NVRs. For a list
of compatible recorders, visit lorextechnology.com/

compatibility.

• Ensure NVR volume is turned on / turned up.

• Ensure audio function on camera is turned on (see ‘Audio
Settings’).

• Ensure audio is turned up on viewing device.

Troubleshooting

Using the Weatherproofing Cap (Optional)

Camera Ethernet Connector

O-Ring Rubber Stopper

Barrel End Cap

1. Fit the O-ring around the camera Ethernet connector.

2. Feed the Ethernet extension cable through the end cap and the barrel as
shown above. Connect the cable to the camera Ethernet connector.

3. Twist the barrel securely onto the camera Ethernet connector. The o-ring
becomes compressed when the seal is properly tight.

4. Split the rubber stopper to wrap it around the cable between the barrel
and end cap as shown above. Push the rubber stoppper toward the barrel
until it is underneath the teeth at the end of the barrel.

5. Twist the end cap securely onto the barrel. The rubber stopper becomes
compressed and will stick out of the end cap slightly when the seal is
properly tight.