CAUTION: Read instruction carefully and turn electricity off at main circuit breaker panel
before beginning installation.
Care and Cleaning
To clean the outside of the fixture, use a dry or slightly dampened clean cloth(use clean
water, never a solvent)to wipe the surface of the fixture.
To clear the inside of the fixture, first disconnect power to the fixture by turning off the circuit
breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean
cloth(use clean water, never a solvent) to wipe the interior surface of the fixture
Do not use any cleaners with chemical, solvents or harsh abrasives. Use Only a dry soft cloth
to dust or wipe carefully.
Estimated Assembly Time:30 minutes
Part List and Hardware List
Assembly Instruction
Socket sleeve
1X
3X
2X
1X
Wire Nut
Mounting Plate
Mounting Screw
Bulb
PIECE
DESCRIPTION
PICTURE
QUANTITY
PIECE
DESCRIPTION
PICTURE
QUANTITY
A
C
F
B
D
1X
G
H
2X
E
1X
1X
J
K
6X
L
6X
1X
1X
M
1X
N
Ground Screw
Canopy
Hanging Loop
Canopy Nut
Closable link/cap
Chain
Lamp Boby
Finial
II
1X
Fixture Loop
1 / 3
Installation
Step 1
Step 2
Step 3 Wire connection
*Note: When parallel wire(SPTI&SPTII)is used. The neutral wire is square shaped and
ridged and the hot wire will be round in shape and smooth.(See illustration on left)
Grounding Instructions:
*Parallel Cord(round&smooth)
*Parallel Cord(square&ridged)
Clear,Brown,Gold or Black without Tracer(colored stripes)
Clear,Brwn,Gold or Black without Tracer(colored stripes)
Insulated Wire(not green)with copper metal conductor
Insulated Wire(not green)with Silver metal conductor
Connect,Hot,Black or Red outlet Supply Wire to:
Connect,Neutral,White Outlet Supply Wire to:
Black
White
Unpack all parts from cartons carefully.
Weave the 2 wire power cord and bare ground
wire through every other loop to the top of
chain(J),center holes of Hanging
Loop(F)&Canopy(E)&Mounting Plate(B) as
diagram.
Insert the threaded tube of the Mounting Plate(B)
into the center hole of the Hangling
Loop(F),rotate the Mounting Plate(B) clockwise
till tight.
Slide the Canopy Nut(G) then the Canopy(E) to
the end of the Chain(J).
Screw the Chain(J) to the Hanging Loop(F) and
the Fixture Loop (I) with Closable link/cap (H)
as diagram.
G
H
H
I
M
I
G
H
2 / 3
a) For installation in the United States: Wrap ground wire from outlet box around green
ground screw on mounting bracket, no less than 2" from wire end. Tighten ground screw. If
fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector.
b) For installation in Canada: If fixture is supplied with ground wire, wrap ground wire
around green grounding screw on mounting bracket. Tighten ground screw.
Step 4
PLEASUE USE TYPE"B" BULB MAX 40-WATT
OR CFL BULB MAX 9-WATT
THERE ARE 6PCS 25-WATT TYPE"B" BULBS
IN THE BOX.
Step 5
Consult a qualified electrician to ensure correct branch
circuit conductor
ENJOY YOUR LAMP
Attach the Mounting Plate (B) onto the junction
box by inserting two Mounting Screws (D) and
turning clockwise till tight.
Slide the Canopy (E) upward along the chain(J)
till the ceiling surface. Fix the Canopy(E) by
rotating the Canopy Nut(G)clockwise to engage it
with the threaded portion of the Hanging Loop (F)
until secure. Do not over tighten this nut.
Attach the Finial(N) onto the threaded portion of
the bottom of the lamp body and rotate it
clockwise till tight.
Place each Socket Sleeve(K) onto each socket
until secure.
Insert the bulbs(L) into the sockets until secure.
DO NOT EXCEED THE SPECIFIED WATTAGE.
N
M
E
G
J
K
A
B
D
F
3 / 3
Loading...