Accessories
Terminations, Adapters
terminations
and
adapTers
Terminations AND ADAPTERS
Product
1N5339B
Termination Device
SE-TA6-SM
Stud-Mount Termination Assembly
SE-TA6
Termination Assembly
SE-TA6A
(PGA-0T6A)
Termination Assembly
SE-TA6A-WL
Termination Assembly
SE-TA6ASF-WL
Small-Format Termination
Assembly with Wire Leads
SE-TA12A
Termination Assembly
SE-TA12ASF-WL
Small-Format Termination
Assembly with Wire Leads 
SE-TA12A-WL
Termination Assembly
SE-TA12A
SE-TA12B
Termination Assemblies
PPI-600V
Parallel Path Isolator
RK-13
Relay Interface Module
SE-485-DIN
Industrial RS-485 to RS-232
Converter
SE-485-PP
Port-Powered Serial
Converter
CA-945
Serial Connector Adapter Kit
SE-ICUSB232
USB to RS-232 Converter
Features
5 W axial-lead ground-check termination. Included with SE-105 and SE-107.
50 W ground-check termination that is robust and compact for submersible pumps. Wire lead simplifies installation. (Replacement for 1N4553B)
50 W ground-check termination with convenient mounting holes and screw terminals.
Temperature compensated 50 W ground-check termination with convenient mounting holes and screw terminals.
Temperature compensated 50 W ground-check termination with convenient mounting holes and screw terminals.
Temperature compensated 12 W ground-check termination, ideal for use in cable-coupler end caps and submersible pumps. Mounting holes and wire leads.
Temperature compensated 50 W ground-check termination with convenient mounting holes and screw terminals.
Temperature compensated 12 W ground-check termination, ideal for use in cable-coupler end caps and submersible pumps. Mounting holes and wire leads.
Temperature compensated 50 W ground-check termination with convenient mounting holes and screw terminals.
Used together to allow an SE-134C to monitor a splitter box and two cables.
Parallel ground-path rejection for ground-check monitors. Eliminates intermachine arcing and prevents stray DC currents from flowing in a monitored ground wire.
Separate ground-fault and ground-check indication contacts for the SE-105, and separate ground-fault and resistor-fault contacts for the SE-325. Used to provide output to a PLC and operate standard pilot lights. Complete with conformally coated circuit boards.
Industrial network quality RS-485 to RS-233 serial converter. DIN-rail mounted, 24 Vdc required.
Converts an RS-485 signal to an RS-232 signal. Used for set-point programming and updating flash memory. 115.2 kbit/s maximum transfer rate.
Connects an RJ45 to a 9-pin serial connector. Includes 1.5 m cable and plug-in adapter.
Connects a 9-pin serial cable to a USB port.
Accessory For
SE-105
SE-107
SE-105
SE-107
SE-105
SE-107
SE-105
SE-107
SE-134C
SE-105
SE-107
SE-134C
SE-105
SE-107
SE-134C
SE-135
SE-145
SE-135
SE-145
SE-135
SE-145
SE-134C
SE-105 SE-107
SE-134C SE-135
SE-105 SE-107
SE-325
MPS
FPS
MPU-32 MPS
FPU-32 FPS
MPU-32
FPU-32
SE-330 |
CA-945 |
SE-330AU |
SE-330HV |
SE-485-PP |
SE-485-DIN |
www.littelfuse.com/relayscontrols |
© May 2012 Littelfuse Protection Relays & Controls |
Loading...