Flow Down™
Aftermarket Manual
Flow Down™
Aftermarket
Manual
Table of Contents
Introduction ............................................ 2
Parts List ............................................... 2
Operation .............................................. 3
Notes................................................... 4
www.lippertcomponents.com (574) 537-8900 Rev: 01.15 - Flow Down Aftermarket Manual
1
Flow Down™
Aftermarket Manual
Introduction
Flow Down™ keeps your drain hose up off the ground and easily
adjusts to nearly any slope, which prevents sewage from
getting trapped in the hose. This premium, adjustable RV drain
support system will help prevent odor and protect your hose
from damage.
No more carrying lumber, rocks or modied PVC pipe to hold
your hose up off the ground. The legs of each section can be
simply adjusted using the knobs at each half pipe connection.
One kit extends to over 10 feet and it can be easily expanded
to 20 feet by purchasing another kit.
Quick Facts
• Quick setup
• Adjustable legs
• 10 feet extended
• Storage bag included
Helpful Hints
• If you need to place the Flow Down around an object or corner,
you can eliminate one of the half pipes and place two of the
center ttings end to end at any angle to create an elbow.
• Bungee cords can be used to wrap around the Flow Down
support and the RV drain hose for extended stay, which makes
a more stable sewer connection.
Parts List
A
Letter Part# Description
A 365044 Storage Bag
B 365045 10” Stake
C 365046 Half Pipe
D 365051 End Fitting
E 365052 Middle Fitting
B
C
D
E
www.lippertcomponents.com (574) 537-8900 Rev: 01.15 - Flow Down Aftermarket Manual
2
Operation
Flow Down™
Aftermarket Manual
1. Holding a single end tting and a half pipe, rotate the half pipe
into the end tting (Fig. 1). (Fittings have only one opening and
a stop on the other side which allows for rotation one way only
(Fig. 2A).
A
Fig. 1 Fig. 2
2. Rotate a middle tting onto the half pipe from Step 1 (Fig. 3).
3. Rotate a half pipe into the open end of the middle tting (Fig. 4).
4. Repeat these steps until there is an end tting on each end and
middle ttings in the center of the drain support.
5. Now position one end close to the RV and the other end at the
sewer connection of the RV Park.
6. Starting at the RV, slide a 10” stake down through the pinch
bolts but do not tighten (Fig. 5).
7. Repeat Step 6 on each tting.
8. After they are all in place, adjust the RV end of the Flow
Down so it is as high as possible but still under the RV Sewer
hookup. Now tighten the sliding square shafts snuggly,
but DO NOT OVER TIGHTEN.
9. Repeat this procedure on each tting from the RV outward to
the park sewer connection, keeping in mind that there should
be at least 1/4 inch drop per foot in the Flow Down to allow the
black and gray water to ow and avoid back-up into the RV
(Fig. 6).
10. You are now ready to lay your RV drain hose into the Flow
Down Fully Adjustable RV Drain Hose Support! Attach
one end to the RV and insert the other into the park sewer
connection.
Fig. 3
Fig. 4
www.lippertcomponents.com (574) 537-8900 Rev: 01.15 - Flow Down Aftermarket Manual
3
Fig. 5
Fig. 6
Notes
Flow Down™
Aftermarket Manual
Manual information may be distributed as a complete
document only, unless Lippert Components provides explicit
consent to distribute individual parts.
All manual information is subject to change without notice.
Revised editions will be available for free download at www.
lippertcomponents.com. Manual information is considered
factual until made obsolete by a revised version.
Please recycle all obsolete materials and contact Lippert
Components with concerns or questions.
www.lippertcomponents.com (574) 537-8900 Rev: 01.15 - Flow Down Aftermarket Manual
4
Loading...