KOMPONENT
110, 106, 104
Advanced Features
Copyright and Acknowledgements
Copyright © 2005 Linn Products Ltd. First edition May 2005.
Linn Products Limited, Glasgow Road, Waterfoot, Eaglesham, Glasgow, G76 OEQ,
Scotland, United Kingdom
All rights reserved. No part of this publication may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission of the
publisher.
Printed in the United Kingdom.
Trade marks used in this publication:
LLiinnnn
and the
LLiinnnn llooggoo
are registered trade marks
of Linn Products Limited. KOMPONENT is a trade mark of Linn Products Limited.
The information in this manual is furnished for informational use only, is subject to
change without notice, and should not be construed as a commitment by Linn Products
Limited. Linn Products Limited assumes no responsibility or liability for any errors or
inaccuracies that may appear in this manual.
i
KOMPONENT 110, 106, 104
ADVANCED FEATURES
Copyright and Acknowledgements
English
KOMPONENT 110, 106, 104
ADVANCED FEATURES
Contents
English
Contents
Installation 1
Positioning 1
Levelling (spiked floor-stand mounting only) 2
Connecting 3
General 3
Terminals 3
Cable-routing 3
Configuration options 3
Link strip information 4
Wiring / amping configurations 5
Single-wiring 5
Bi-wiring or bi-amping 5
Tri-wiring or tri-amping 5
Quad-wiring or quad-amping 5
(KOMPONENT 110 & 106 only)
AKTIV configuration 6
Note:
The acoustic array on the KOMPONENT 106 centre channel has been factory
configured for horizontal dispersion. It can however be converted, by your
Authorised Linn Retailer, to allow the loudspeaker to be positioned vertically.
Vertical positioning without conversion is not recommended.
KOMPONENT 106 horizontal alignment –
factory configuration
KOMPONENT 106 vertical alignment –
requires conversion
5.1 system suggested speaker positioning
1
Installation
Positioning
The KOMPONENT loudspeakers have been designed to provide a very flexible
loudspeaker solution. Stand-mounting, wall-mounting and (in the case of the
106 and 104 models) shelf-mounting provide setup options to suit any
application or room layout. An example of such a layout (for a 5.1 system) is
shown below. Ideally, the distance between the front left and right loudspeakers
should equal the distance to the listening position, as indicated.
Whichever mounting method you employ, for best results ensure that the
loudspeakers are held rigidly or positioned stably. This will ensure that as much
of the movement of the drive units as possible is converted to sound energy,
rather than cabinet movement (in the form of vibration, wobble etc.).
The KOMPONENT loudspeakers generally perform best with very little toe-in
(i.e. only very slight angling of the loudspeakers towards the listening position
is required). Some experimentation with the positioning and angle of your
loudspeakers may help to optimise the sound within your room setting.
KOMPONENT 110, 106, 104
ADVANCED FEATURES
Installation
English
KOMPONENT 110
KOMPONENT 104
KOMPONENT 106
KOMPONENT 106
KOMPONENT 120
Levelling (spiked floor-stand mounting only)
The procedure for levelling each loudspeaker should be as follows:
●
Being careful not to scratch the cabinet, use a spirit level to check if it is
sitting level. If it is, gently rock the loudspeaker from front to back, side to
side and diagonally to check for any movement. If none is present and the
loudspeaker is sitting level, no adjustment to the spikes is necessary.
●
If the loudspeaker is not level, or moves when you rock it, loosen the
appropriate lock nuts using the tool provided (1) and use a screwdriver to
turn the spikes to adjust their height (2).
●
Press down firmly on the top of the loudspeaker to ensure it is in close
contact with your flooring.
●
Use the spirit level as before and continue to adjust the spikes as
required.
●
When the loudspeaker is level and does not rock, use the screwdriver to
hold the spike in place and tighten the lock nuts using the tool provided
(3).
Note:
To protect wooden or tiled floors, the spikes can be
placed on the floor-protectors, which are supplied
with the KOMPONENT spiked stands.
2
KOMPONENT 110, 106, 104
ADVANCED FEATURES
Installation
English
x4
x4
1
2
3
Connecting
General
IMPORTANT. Before making any connections, switch off all products in your hi-fi
or AV system.
Terminals
The terminals are hidden under a removable cover. To access the terminals,
unclip the cover by carefully pushing its edges inwards. If your connection and
cable-routing method allow, the terminal cover can sometimes be refitted after
making the connections.
The loudspeakers are fitted with binding-post terminals. These terminals can be
used as sockets for the connection of 4mm banana plugs. They can also be
used as binding posts for the connection of bared wires or spade-terminated
cables by loosening the outer section of the binding post (do not attempt to
completely remove this outer section), inserting the cable or terminal and retightening to clamp it in place and provide a good electrical connection.
Cable-routing
In the case of the KOMPONENT 110 and KOMPONENT 104 (where stand is
fitted), the cable(s) can be routed through a hidden channel inside the stand to
provide an invisible connection if so desired. See stand fitting instructions,
supplied with the stands.
Note:
Fit the stand before routing the cable(s).
Configuration options
The KOMPONENT loudspeakers offer an array of configuration options, as
described below. Connections for each of the methods are shown in the
Wiring
and amping configurations
chapter, later in this manual.
The options are listed in order of increasing sonic performance. Multi-wiring and
multi-amping options offer improvements in sound quality over single-wiring. The
greater the separation of the frequency bands in the amplifiers, crossover and
cables, the more precise the quality of the playback performance; with AKTIV
operation representing the ultimate configuration (see
AKTIV operation,
below).
PPaassssiivvee ssiinnggllee--wwiirriinngg
– a single amplifier channel connects to the loudspeaker
using a single cable.
PPaassssiivvee mmuullttii--wwiirriinngg ((bbii--wwiirree,, ttrrii--wwiirree oorr qquuaadd--wwiirree))
– a single amplifier channel
connects to the loudspeaker using two, three or four cables (note – quad-wiring is
not available for KOMPONENT 104).
PPaassssiivvee mmuullttii--aammppiinngg ((bbii--aammpp,, ttrrii--aammpp oorr qquuaadd--aammpp))
– two, three or four amplifier
channels connect to the loudspeaker (note – quad-amping is not available for
KOMPONENT 104).
Note:
Multi-amping can be combined with multi-wiring – e.g. bi-amping could employ tri-wiring.
AAKKTTIIVV ooppeerraattiioonn..
The term ‘AKTIV’ refers to the proprietary Linn active
crossovers and loudspeaker configuration, whereby the loudspeaker’s internal
passive crossover is effectively replaced with external AKTIV crossovers.
AKTIV or passive? In passive mode, the output from the power amplifier is
passed through the passive crossover inside the loudspeaker. A portion of the
signal’s energy is used to drive the crossover circuitry and therefore is effectively
lost. In an AKTIV system, on the other hand, the crossover circuitry is mainspowered which eliminates its reliance on the signal for its power and also allows
advanced circuitry to be included. This allows the crossover to exert a much
greater degree of control over the processing of the audio signal, providing a
more precise audio output to the drive units and therefore resulting in
significantly improved sonic performance, compared with passive operation.
Important note:
AKTIV operation requires a modification to your loudspeakers and in some cases
your amplifiers, which must be carried out by an Authorised Linn Retailer.
3
KOMPONENT 110, 106, 104
ADVANCED FEATURES
Connecting
English
Spade-terminated Cable
Banana Plug
Bared Wire Connection
Link strip information
To remove / fit the link strips:
●
Loosen the outer section of each binding post on one row of terminals (do
not remove these posts completely).
●
Slide the link strip outwards to remove.
●
When refitting the strips, please ensure that they are fully and correctly
inserted.
●
Ensure that all the binding posts are tight (whether the strips are being
refitted or not).
●
Repeat the process for the second row.
To modify the link strips for multi-wiring or multi-amping applications:
●
Remove the link strip from the loudspeaker, as explained above.
●
Determine where you require to make the break (see multi-wiring /
multi-amping options below for guidance).
●
At one of the break-points (indicated) you can break the link by using a
strong pair of snips, a small hacksaw or snap it at one of the break-points
by carefully bending it back and forth with pliers.
●
File down any sharp edges to prevent the possibility of injury.
Note:
If you will be using both sides of the separated link, ensure your break creates a
definite gap in order to eradicate the possibility of the links accidentally
re-connecting when fitted to the loudspeaker.
Important notes on using the link strips
The configurations below are only suggestions – others are possible. If you are
trying other setups, we would advise that you consult an Authorised Linn
Retailer and please bear in mind the following points:
●
Never use the strips to link positive (+) and negative (-) terminals
together.
●
When multi-amping, ensure that the link strips do not short-circuit amplifier
channels together. Shorting the outputs of separate amplifier channels
together can damage the amplifier(s) and loudspeaker drive units.
●
Do not connect more than one strip per terminal.
4
KOMPONENT 110, 106, 104
ADVANCED FEATURES
Connecting
English
Break points
Wiring / amping configurations
Single-wiring
Position of link strips if single-wiring (i.e. using a single cable from one power
amplifier channel). No link adjustments or cuts are required.
Bi-wiring or bi-amping
Suggested position of separated link strips if bi-wiring (i.e. using two cables
from one power amplifier channel) or bi-amping (i.e. using two power amplifier
channels.
KOMPONENT 110, 106, 104
ADVANCED FEATURES
Wiring / amping configurations
English
KOMPONENT 110 or 106 KOMPONENT 104
Output from
power amplifier
can be connected
to any of the
four pairs of
terminals.
Output from
power amplifier
can be connected
to any of the
three pairs of
terminals.
KOMPONENT 110 or 106 KOMPONENT 104
Output from
power amplifier
can be connected
to either of the
two pairs of
terminals.
Output from
power amplifier
can be connected
to either of the
two pairs of
terminals.
Output from
power amplifier
can be connected
to either of the
two pairs of
terminals.
Tri-wiring or tri-amping
Suggested position of separated link strips if tri-wiring (i.e. using three cables
from one power amplifier channel) or tri-amping (i.e. using three power
amplifier channels).
Please note - link strips MUST be removed completely on KOMPONENT 104.
Quad-wiring or quad-amping (KOMPONENT 110 & 106)
Link strips MUST be removed when quad-wiring (i.e. using four cables from one
power amplifier channel) or quad-amping (i.e. using four power amplifier
channels).
KOMPONENT 110 or 106 KOMPONENT 104
Output from
power amplifier
can be connected
to either of the
two pairs of
terminals.
KOMPONENT 110 or 106
5
AKTIV configuration
Important notes:
AKTIV operation requires a modification to your loudspeakers and in some
cases, your amplifiers, which must be carried out by an Authorised Linn
Retailer.
In AKTIV mode, please be very careful to connect all cables from the
amplifier(s) to the correct sockets on the loudspeaker. Wrong connection could
result in damage to your loudspeaker drive units and amplifier.
6
KOMPONENT 110, 106, 104
ADVANCED FEATURES
Wiring / amping configurations
English
KOMPONENT 110 or 106 KOMPONENT 104
From mid
power amplifier
From tweeter
power amplifier
From tweeter
power amplifier
From bass
power amplifier
From mid
power amplifier
From bass
power amplifier
From lower- bass
power amplifier
Loading...