Linksys WRT51AB User Manual

Instant Wireless®Series

Dual-Band Wireless A+B Broadband Router

Use this guide to install: WRT51AB

User Guide

FCC RF Radiation Exposure Statement To comply with the FCC and ANSI C95.1 RF exposure limits, the antenna(s) for this device must comply with the following:

1. Access points with 2.4 GHz or 5 GHz integrated antenna must operate with a separation distance of at least 20 cm from all persons using the cable provided and must not be co-located or operating in conjunction with any other antenna or transmitter.

2. The Access Point's co-located 2.4 GHz and 5 GHz integrated antennas support a minimum separation distance of 10 cm (3.9 in.) and are compliant with the applicable FCC RF exposure limit when transmitting simultaneously.

End-users must be provided with specific operations for satisfying RF exposure compliance. Note: Dual antennas used for diversity operation are not considered co-located.

Canadian Department of Communications Industry Canada (IC) Notice This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Cet appareil numérique de la classe B est conforme à la norme NMB-003 et CNR-210 du Canada. "To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing." " Pour empêcher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit être utilisé à l'intérieur et devrait être placé loin des fenêtres afin de fournir un écran de blindage maximal. Si le matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence. "

EC DECLARATION OF CONFORMITY (EUROPE) Linksys Group declares that the Instant Wireless®Series products included in the Instant Wireless®Series conform to the specifications listed below, following the provisions of the European R&TTE directive 1999/5/EC, EMC directive 89/336/EEC, and Low Voltage directive 73/23/EEC:

For 11Mpbs, 2.4 GHz access points with 100 mW radios, the following standards were applied:

• ETS 300-826, 301 489-1 General EMC requirements for Radio equipment.

• EN 609 50 Safety

• ETS 300-328-2 Technical requirements for Radio equipment. For 54 Mpbs, 5 GHz access points with 40 mW radios, the following standards were

applied:

• ETS 301 489-1, 301 489-17 General EMC requirements for Radio equipment.

• EN 609 50 Safety

• ETS 301-893 Technical requirements for Radio equipment. Caution: The frequencies used by 802.11a wireless LAN devices are not yet harmonized

within the European community, 802.11a products are designed for use only in specific countries, and are not allowed to be operated in countries other than those of designated use. Contact local Authority for procedure to follow.

Caution: This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. Contact local Authority for procedure to follow.

Note: Combinations of power levels and antennas resulting in a radiated power level of above 100 mW equivalent isotropic radiated power (EIRP) are considered as not compliant with the above mentioned directive and are not allowed for use within the European community and countries that have adopted the European R&TTE directive 1999/5/EC and/or the CEPT recommendation Rec 70.03.

For more details on legal combinations of power levels and antennas, contact Linksys Corporate Compliance.

COPYRIGHT & TRADEMARKS Copyright © 2002 Linksys, All Rights Reserved. Instant Wireless, Linksys, and the Linksys logo are registered trademarks of Linksys Group, Inc. Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation. All other trademarks and brand names are the property of their respective proprietors.

LIMITED WARRANTY Linksys guarantees that every Instant Wireless Dual-Band Wireless A+B Broadband Router will be free from physical defects in material and workmanship for one year from the date of purchase, when used within the limits set forth in the Specifications section of this User Guide. If the product proves defective during this warranty period, call Linksys T echnical Support in order to obtain a Return Authorization number. BE SURE TO HAVE YOUR PROOF OF PURCHASE ON HAND WHEN CALLING. When returning a product, mark the Return Authorization number clearly on the outside of the package and include a copy of your original proof of purchase. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE. All customers located outside of the United States of America and Canada shall be held responsible for shipping and handling charges.

IN NO EVENT SHALL LINKSYS'S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, ITS ACCOMPANYING SOFTWARE, OR ITS DOCUMENTATION. LINKSYS OFFERS NO REFUNDS FOR ITS PRODUCTS. Linksys makes no warranty or representation, expressed, implied, or statutory, with respect to its products or the contents or use of this documentation and all accompanying software, and specifically disclaims its quality, performance, merchantability, or fitness for any particular purpose. Linksys reserves the right to revise or update its products, software, or documentation without obligation to notify any individual or entity. Please direct all inquiries to:

Linksys P.O. Box 18558, Irvine, CA 92623. SAFETY AND REGULATORY NOTICES FCC STATEMENT

The Instant Wireless Dual-Band Wireless A+B Broadband Router has been tested and found to comply with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may

cause undesired operation.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment or devices

• Connect the equipment to an outlet other than the receiver's

• Consult a dealer or an experienced radio/TV technician for assistance

FCC Caution: Any change or modification to the product not expressly approved by Linksys could void the user's authority to operate the device.

UG-WRT51AB-102202NC JL

Instant Wireless®Series Dual-Band Wir eless A+BBroadband Router

• Linksys Group vakuuttaa täten että Instant Wireless Dual-Band A+B Broadband Router tyyppinen laite on direktiivin 1999/5/EY, direktiivin 89/336/EEC ja direktiivin 73/23/EEC oleellisten vaatimusten ja sitä koskevien näiden direktiivien muiden ehtojen mukainen.

• Linksys Group déclare que la Instant Wireless Dual-Band A+B Broadband Router est conforme aux conditions essentielles et aux dispositions relatives à la directive 1999/5/EC, la directive 89/336/EEC, et à la directive 73/23/EEC.

• Belgique B L'utilisation en extérieur est autorisé sur le canal 11 (2462 MHz), 12 (2467 MHz), et 13 (2472 MHz). Dans le cas d'une utilisation privée, à l'extérieur d'un bâtiment, au-dessus d'un espace public, aucun enregistrement n'est nécessaire pour une distance de moins de 300m. Pour une distance supérieure à 300m un enregistrement auprès de l'IBPT est requise. Pour une utilisation publique à l'extérieur de bâtiments, une licence de l'IBPT est requise. Pour les enregistrements et licences, veuillez contacter l'IBPT.

• France F:

2.4 GHz Bande : les canaux 10, 11, 12, 13 (2457, 2462, 2467, et 2472 MHz respectivement) sont complétement libres d'utilisation en France (en utilisation intérieur). Pour ce qui est des autres canaux, ils peuvent être soumis à autorisation selon le départment. L'utilisation en extérieur est soumis à autorisation préalable et très restreint.

5 GHz Bande: Conformément aux décisions de la CEPT, l'utilisation des fréquences

de la bande 5150 MHz - 5350 MHz est autorisée à l'intérieur des bâtiments avec une puissance maximale de 200 mW, et interdite en extérieur. La bande 5470 MHz - 5725 MHz n'est pas ouverte aujourd'hui.

Vous pouvez contacter l'Autorité de Régulation des Télécommunications

(http://www.art-telecom.fr) pour de plus amples renseignements.

2.4 GHz Band: only channels 10, 11, 12, 13 (2457, 2462, 2467, and 2472 MHz respectively) may be used freely in France for indoor use. License required for outdoor installations.

5 GHz Band: frequencies in the 5150 MHz - 5350 MHz band may be used indoor

with maximum power of 200 mW. Their use is forbidden outdoors. The 5470 MHz 5725 MHz band is not currently open.

Please contact ART (http://www.art-telecom.fr) for procedure to follow.

• Deutschland D: Anmeldung im Outdoor-Bereich notwending, aber nicht genehmigungspflichtig. Bitte mit Händler die Vorgehensweise abstimmen.

• Germany D: License required for outdoor installations. Check with reseller for procedure to follow.

• Italia I: E' necessaria la concessione ministeriale anche per l'uso interno. Verificare con i rivenditori la procedura da seguire. L'uso per installazione in esterni non e' permessa.

• Italy I: License required for indoor use. Use with outdoor installations not allowed.

• The Netherlands NL License required for outdoor installations. Check with reseller for procedure to follow.

• Nederlands NL Licentie verplicht voor gebruik met buitenantennes. Neem contact op met verkoper voor juiste procedure.

Table of Contents

Chapter 1:Introduction 1

The Dual-Band Wireless A+B Broadband Router 1 Features 2 The Router’s Functions 2 IPAddresses 3 Router Setup Overview 4

Chapter 2:Getting to Know the Dual-Band Wireless A+BBroadband Router 6

The Router’s Back Panel 6 The Router’s Front Panel LEDs 7

Chapter 3:Connect theRouter 10

Overview 10 Wired Connection to a PC 10 Wireless Connection to a PC 12

Chapter 4: Configure the PCs 13

Overview 13 Configuring Windows 98 and Millennium PCs 14 Configuring Windows 2000 PCs 16 Configuring Windows XP PCs 18

Chapter 5:Configure the Router’s Basic Settings20 Chapter 6: The Router’s Web-based Utility 25

Overview 25 How to Access the Web-based Utility 25 Setup 26 Password 38 Status 39 DHCP 42 Log 44 Help 45 Advanced Tabs 47 Advanced Wireless 48 Filters 55 Port Forwarding 58 Routing 60 DMZ Host 63 MAC Address Clone 64

Dual-Band Wireless A+B Broadband Router

Chapter 1:Introduction

s EtherFast®Cable/DSL Router

The Dual-Band Wireless A+B Broadband Router is like four devices in one box! The Router function lets you securely share one high-speed Internet connection among your entire network, w hile the 4-port, 10/100 switch jump-starts your wired Ethernet network. Connect four PCs directly, or daisy-chain out to more hubs and switches to create as big a network as you need.

The Dual-Band Wireless A+B Broadband Router also contains two wireless access points, which let you connect with wirelessly networked PCs using either the popular 2.4GHz, 802.11b standard at 11Mbps, or the new, almost five times faster, 5GHz, 802.11a standard. Since both standards are built-in, you can protect your investment in existing 802.11b equipment today, and migrate to the 802.11a standard as your needs grow.

In addition to up to 152-bit encryption of wireless transmissions, the two access points in the Dual-Band Wireless A+B Broadband Router support the industrial-strength wireless security of 802.1x authentication and authorization. The Router also serves as a DHCP server, has NAT technology to protect against Internet intruders, supports VPN pass-through, and can be conf igured to filter internal users’ access to the Internet. Configuration is a snap with the web browser-based configuration utility.

With the Linksys Dual-Band Wireless A+B Broadband Router at the center of your home or office network, you can share a high-speed Internet connection, files, printers, and multi-player games with the flexibility, speed, and security you need!

The Dual-Band Wireless A+B Broadband Router

Instant Wireless®Series

Appendix A: Troubleshooting 66

Common Problems and Solutions 66 Frequently Asked Questions 77

Appendix B: How to Ping Your ISP’s E-mail & Web Addresses 86

Appendix C: Configuring Wireless Security 89

Background 89 WEP Encr yption 90

802.1x Authentication 91 MD5 Authentication for Windows XP 92 Digital Certif icate Installation 97 TLS Authentication for Windows XP 101

Appendix D: Finding the MAC Address and IP Address for Your Ether net Adapter 105

Appendix E: Glossary 108 Appendix F: Specifications 126

Environmental 127

Appendix G: Warranty Information 128 Appendix H: Contact Information 129

Dual-Band Wireless A+B Broadband Router

What’s an IP Address?

IP stands for Internet Protocol. Every device on an IP-based network, including PCs, print servers, and routers, requires an IP address to identify its “location,” or address, on the network. This applies to both the Internet and LAN connections. There are two ways of assigning an IP address to your netw ork de vices. You can assign static IP addresses or use the Router to assign IP addresses dynamically.

Static IP Addresses

A static IP address is a fixed IP address that you assign manually to a PC or other device on the network. Since a static IP address remains valid until you disable it, static IP addressing ensures that the device assigned it will always have that same IP address until you change it. Static IP addresses must be unique and are commonly used with network devices such as server PCs or print servers.

If you use the Router to share your cable or DSL Internet connection, contact your ISP to find out if they have assigned a static IP address to your account. If so, you will need that static IP address when configuring the Router. You can get that information from your ISP.

IP Addresses

Note: Since the Router is a device that connects two networks, it needs two IP addresses—one for the LAN, and one for the Internet. In this User Guide, you’ll see references to the “Internet IP address” and the “LAN IP address.”

Since the Router uses NAT technology, the only IP address that can be seen from the Internet for your network is the Router’s Internet IP address.

However, even this Internet IP address can be blocked, so that the Router and network seem invisible to the Internet—see the Block WAN Requests description under Filters in “Chapter 6: The Router’s Web-based Utility.”

Instant Wireless®Series

• Compatibility with 802.11a (5GHz) and 802.11b (2.4GHz) Standards

• Built-in, 4-Port, 10/100 Switch Supports Wired Ethernet Clients

• All Ethernet Ports Support Auto-MDI/MDI-X—No Need for Crossover

Cables

• Unsurpassed Security Using 802.1x Authentication with up to 152-bit WEP

Encryption

• Enhanced Security Management Functions: Port Filtering, MAC and IP

Address Filtering, DMZ Hosting, and NAT Technology

• Access Your Corporate Network Remotely through Virtual Private

Networking (VPN)—Supports IPSec and PPTP Pass-Through

• Easily Configurable through a Web Browser—Locally and over the Internet

• DHCP Server Capability to Assign IP Addresses Automatically

• Supports Static and Dynamic Routing (RIP1 and 2)

• Free Technical Support—24 Hours a Day, 7 Days a Week, Toll-Free US Calls

• 1-Year Limited Warranty

Simply put, a router is a network device that connects two networks together.

In this instance, the Router connects your Local Area Network (LAN), or the group of PCs in your home or office, to the Internet. The Router processes and regulates the data that travels between these two networks.

The Router’s NAT feature protects your network of PCs so users on the public, Internet side cannot “see” your PCs. This is how your network remains pri v ate. The Router protects your network by inspecting every packet coming in through the Internet port before delivery to the appropriate PC on your network. The Router inspects Internet port services like the web server, ftp server, or other Internet applications, and, if allowed, it will forward the packet to the appropriate PC on the LAN side.

Remember that the Router’s ports connect to two sides. The 10/100 LAN ports connect to the LAN, and the Internet port connects to the Internet. The LAN ports transmit data at 10 Mbps or 100 Mbps, and the broadband port, or Internet port, transmits data at 10/100 Mbps.

The Router’s Functions

Features

Dual-Band Wireless A+B Broadband Router

This User Guide covers the steps for setting up a network with the Router. After going through “Chapter 2: Getting to Know the Dual-Band Wireless A+B Broadband Router,” most users will only need to use the following chapters:

• Chapter 3: Connect the Router

This chapter instructs you on how to connect a cable or DSL modem to the Router and connect your PC(s) to the Router.

• Chapter 4: Configure the PCs

This chapter instructs you on how to configure your PCs to be DHCP clients, if you have previously set static IP addresses on your PCs.

• Chapter 5: Configure the Router’s Basic Settings

This chapter explains how to configure the Router using your web browser and the Router’s web-based utility. You will conf igure the Router for Internet access using the settings provided by your ISP.

When you’re finished with these basic steps, you will be ready to connect to the Internet. You can also modify the Router’s settings further; for example, you can adjust security features and other settings to enable online gaming (see “Chapter 6: The Router’s Web-based Utility”).

Instant Wireless®Series

Figure 1-1

Cable or DSL Modem

Router

PC with Ethernet Adapter

Notebook with Wireless Adapter

Dynamic IP Addresses

A dynamic IP address is automatically assigned to a device on the network, such as PCs and print servers. These IP addresses are called “dynamic” because they are only temporarily assigned to the PC or device. After a certain time period, they expire and may change. If a PC logs onto the network (or the Internet) and its dynamic IP address has expired, the DHCP server will automatically assign it a new dynamic IP address.

DHCP (Dynamic Host Configuration Protocol) Servers

PCs and other network devices using dynamic IP addressing are assigned a ne w IP address by a DHCP server. The PC or network device obtaining an IP address is called the DHCP client. DHCP frees you from having to assign IP addresses manually every time a new user is added to your network.

A DHCP server can either be a designated PC on the network or another network device, such as the Router. By default, the Router’s DHCP Server function is enabled.

If you already have a DHCP server running on your network, you must disable one of the two DHCP servers. If you run more than one DHCP server on your network, you will experience network errors, such as conflicting IP addresses. To disable DHCP on the Router, see the DHCP section in “Chapter 6: The Router’s Web-based Utility.”

Router Setup Overview

Note: Even if you assign a static IP address to a PC, other PCs can still use DHCP’s dynamic IP addressing, as long as the static IP address is not within the DHCP range of the LAN IP Addresses.

If the dynamic IP addressing fails to provide a dynamic IP address, refer to “Appendix A: Troubleshooting.”

Note: You should always you run the Setup Wizard CD-ROM to configure the Router for Inter net access. If you wish to manually conf igure the Router, you may follow the instructions in the Quick Installation guide or this User Guide.

Dual-Band Wireless A+B Broadband Router

Instant Wireless®Series

The Router’s LEDs display information about the Router’s status.

Power Green. The Power LED lights up when the Router is pow ered

on.

Diag Red. The Diag LED lights up when the Router goes through

its self-diagnosis mode during every boot-up. It will turn off upon successful completion of the diagnosis.

If this LED stays on for one minute or longer, see “Appendix A: Troubleshooting.”

The Router’s Front Panel LEDs

Figure 2-2

The Reset Button

The Reset button can be used in one of two ways:

1. If the Router is having problems connecting to the Internet, press the Reset

button for just a moment with a paper clip or a pencil tip. This clears up an y jammed connections, and is similar to pressing the Reset button on your PC to reboot it.

This will reboot the Router while keeping all of the Router’s settings.

2. If you are experiencing extreme problems with the Router and have tried all

other troubleshooting measures, press the Reset Button and hold it down for 10 seconds.

This will restore factory defaults and clear all of the Router’s settings, including settings such as a new password or wireless settings.

Chapter 2:Getting to Know the Dual-Band Wireless A+B Broadband Router

The Router’s ports are located on the Router’s back panel.

Internet The Internet port is where you connect your cable or

DSL modem through an Ethernet network cable. Your modem connection will not work from any other port.

Ports 1-4 These four LAN (Local Area Network) ports con-

nect to network devices, such as PCs, print servers, and network attached storage (NAS). Each of the ports will auto-detect whether a straight-through or crossover cab le is plugged into it, so there is no need for an uplink port. Any one of the four ports can serve as an uplink port to other network devices.

Power The Po w er port is where y ou will connect the power

adapter.

The Router’s Back Panel

Figure 2-1

Dual-Band Wireless A+B Broadband Router

The Internet Indicators

Link/Act Green. The Link/Act LED lights up when a successful con-

nection is made between the Router and your cable or DSL modem (the Internet). The Link/Act LED flickers when the Router is sending or receiving data over the Internet port.

100 Orange. The 100 LED lights up when a successful 100Mbps

connection is made through the corresponding port.

If this LED does not light up, then your connection speed is 10Mbps.

Proceed to “Chapter 3:Connect the Router.”

Instant Wireless®Series

The 802.11a WLAN Indicators

Act Green. When the Act LED flickers, the 802.11a wireless net-

work is active.

Link Green. When the Link LED is continuously lit, the 802.11a

wireless network is available.

The 802.11b WLAN Indicators

Act Green. When the Act LED flickers, the 802.11b wireless net-

work is active.

Link Green. When the Link LED is continuously lit, the 802.11b

wireless network is available.

The LAN Indicators

Link/Act Green. The Link/Act LED serves two purposes. If the LED

is continuously lit, the Router is successfully connected to a device through the corresponding port. If the LED is flickering, the Router is actively sending or receiving data over that port.

Full/Col Green. The Full/Col LED also ser ves two purposes. If this

LED is lit up solidly, the connection made through the corresponding port is running in Full Duplex mode. If the LED flickers, the connection is experiencing collisions (when two PCs send data at the same time). Infrequent collisions are normal.

100 Orange. The 100 LED lights up when a successful 100Mbps

connection is made through the corresponding port.

If this LED does not light up, then your connection speed is 10Mbps.

Dual-Band Wireless A+B Broadband Router

Instant Wireless®Series

3. Connect a different Ethernet network cable from your cable or DSL modem to the Internet port on the Router’s rear panel. This is the only port that will work for your modem connection.

4. Power on the cable or DSL modem.

5. Connect the power adapter to the Router’s Power port, and then plug the power adapter into a power outlet.

• The Power LED on the front panel will

light up green as soon as the power adapter is connected properly.

• The Diag LED will light up red for a few seconds. It will turn off when the

self-test is complete. If this LED stays on for one minute or longer, see “ Appendix A: Troubleshooting.”

6. Power on one of your PCs.

Note: You should always plug the Router’s power adapter into a power strip with surge protection.

Figure 3-2

Figure 3-3

Have yo u checked that the Link/Act LEDs for all your LAN con- nections and the Link LED for your Internet connection light up?

If all of your Link LEDs are not lighting up, make sure that all your cables are securely plugged in, and that all of your hardware is powered on properly. Verify that the modem is plugged into the Internet port on the Router.

Chapter 3:Connect the Router

The Router’s setup consists of more than simply plugging hardware together. You will have to configure your networked PCs to accept the IP addresses that the Router assigns them (if applicable), and you will also have to configure the Router with setting(s) provided by your Internet Service Provider (ISP).

The installation technician from your ISP should have left the setup information for your modem with you after installing your broadband connection. If not, you can call your ISP to request that data.

Once you hav e the setup information you need for your specific type of Internet connection, you can begin installation and setup of the Router.

If you want to use a PC with an Ethernet adapter to configure the Router, go to “Wired Connection to a PC and Boot-Up.” If you want to use a PC with a wireless adapter to configure the Router, go to “Wireless Connection to a PC and Boot-Up.”

1. Before you begin, make sure that all of your network’s hardware is powered off, including the Router, PCs, and cable or DSL modem.

2. Connect one end of an Ethernet network cable to one of the LAN ports (labeled 1-4) on the back of the Router, and the other end to an Ethernet port on a PC.

Repeat this step to connect more PCs, a switch, or other network devices to the Router.

Overview

Wired Connection to a PC

Figure 3-1

Dual-Band Wireless A+B Broadband Router

Chapter 4: Configure the PCs

The instructions in this chapter will help you configure each of your computers to be able to communicate with the Router.

T o do this, you need to configure your PC’s network settings to obtain an IP (or TCP/IP) address automatically, so your PC can function as a DHCP client. Computers use IP addresses to communicate with the Router and each other across a network, such as the Internet.

First, find out which Windows operating system your computer is running. You can find out by clicking the Start button. Read the side panel of the Start menu to find out which operating system your PC is running.

You may need to do this for each computer you are connecting to the Router.

The next few pages tell you, step by step, how to configure your network settings based on the type of W indows operating system you are using. Make sure that an Ethernet or wireless adapter (also known as a network adapter) has been successfully installed in each PC you will configure. Once you’ve conf igured your computers, continue to “Chapter 5: Configure the Router’s Basic Settings.”

Instant Wireless®Series

Important: By default Windows 98, 2000, Me, and XP has TCP/IP installed and set to obtain an IP address automatically.

If your PC does not have TCP/IP installed, click Start and then Help. Search for the keyword TCP/IP. Then follow the instruc- tions to install TCP/IP.

Overview

If you want to use a wireless connection to access the Router, follow these instructions:

1. Before you begin, make sure that all of your network’s hardware is powered off, including the Router, PCs, and cable or DSL modem.

2. Connect an Ethernet network cable from your cable or DSL modem to the Internet port on the Router’s rear panel. This is the only port that will work for your modem connection.

3. Power on the cable or DSL modem.

4. Connect the power adapter to the Power port, and then plug the power

adapter into a power outlet.

• The Power LED on the front panel will light up g reen as soon as the power adapter is connected properly.

• The Diag LED will light up red for a few seconds and turn off when the self-

test is complete. If this LED stays on for one minute or longer, see “Appendix A: Troubleshooting.”

4. Power on one of the PCs on your wireless network(s).

5. For initial access to the Router through a wireless connection, make sure the PC’s wireless adapter has its SSID set to linksys (the Router’s default setting), and its WEP encryption is disabled. After you have accessed the Router, you can change the Router and this PC’s adapter settings to match the your usual network settings.

The Router’s hardware installation is now complete.

Go to “Chapter 4: Conf igure the PCs.”

Wireless Connection to a PC

Note:You should always plug the Router’s pow er adapter into a po w er strip with surge protection.

Figure 3-4

Note: You should always change the SSID from its default, linksys, and enable WEP encryption.

Dual-Band Wireless A+B Broadband Router

3. Click the IP Address tab. Select Obtain an IP address automatically.

4. Now click the Gateway tab, and verify that the Installed Gateway field is blank. Click the OK button.

5. Click the OK button again. Windo ws ma y ask y ou for the original W indows installation disk or additional files. Check for the files at c:\windows\options\cabs, or insert your Windows CD-ROM into your CDROM drive and check the correct f ile location, e.g., D:\win98, D:\win9x, etc. (if “D” is the letter of your CD-ROM drive).

6. Windows may ask y ou to restart your PC. Click the Yes button. If Windows does not ask you to restart, restart your computer anyway.

Go to “Chapter 5: Conf igure the Router’s Basic Settings.”

Instant Wireless®Series

1. Click the Start button. Select Settings and click the Control Panel icon. Double-click the Network icon.

2. On the Configuration tab, select the TCP/IP line for the applicable Ethernet adapter. Do not choose a TCP/IP entry whose name mentions DUN, PPPoE, VPN, or AOL. If the word TCP/IP appears by itself, select that line. Click the Properties button.

Figure 4-2

Figure 4-1

Configuring Windows 98 and Millennium PCs

Dual-Band Wireless A+B Broadband Router

3. Make sure the box next to Internet Protocol (TCP/IP) is checked. Highlight

Internet Protocol (TCP/IP), and click the Properties button.

4. Select Obtain an IP address automatically. Once the new window appears, click the OK button. Click the OK button again to complete the PC configuration.

5. Restart your computer.

Go to “Chapter 5: Configure the Router’s Basic Settings.”

Instant Wireless®Series

1. Click the Start button. Select Settings and click the Control Panel icon. Double-click the Network and Dial-up Connections icon.

2. Select the Local Area Connection icon for the applicable Ethernet adapter (usually it is the first Local Area Connection listed). Double-click the Local Area Connection. Click the Properties button.

Figure 4-4

Figure 4-5

Configuring Windows 2000 PCs

Figure 4-3

Dual-Band Wireless A+B Broadband Router

3. Make sure the box next to Internet Protocol (TCP/IP) is checked. Highlight

Internet Protocol (TCP/IP), and click the Properties button.

4. Select Obtain an IP address automatically. Once the new window appears, click the OK button. Click the OK button again to complete the PC configuration.

5. Restart your computer.

Go to “Chapter 5: Configure the Router’s Basic Settings.”

Instant Wireless®Series

The following instructions assume you are running Windows XP with the default interface. If you are using the Classic interface (where the icons and menus look like previous Windows v ersions), please follow the instructions for Windows 2000.

1. Click the Start button and then the Contr ol P anel icon. Click the Network and Internet Connections icon. Then click the Network Connections icon.

Figure 4-7

Figure 4-8

Configuring Windows XP PCs

Figure 4-6

Dual-Band Wireless A+B Broadband Router

Instant Wireless®Series

3. The web-based utility will appear with the Setup tab selected. Based on the setup instructions from your ISP, you may need to provide the Host Name and Domain Name (usually cable ISPs require them). These fields allow you to provide a host name and domain name for the Router and are usually left blank.

The values for the Router’s LAN IP Address and Subnet Mask are shown on the Setup screen. The default values are 192.168.1.1 for the IP Address and 255.255.255.0 for the Subnet Mask.

4. The Router supports four connection types: Automatic Configuration DHCP (obtain an IP automatically), Static IP, PPPoE, and PPTP. These types are listed in the drop-down menu for the Configuration Type setting. Each Setupscreen and av ailab le features will dif fer depending on w hat kind of connection type you select. Proceed to the instructions for the connection type you are using, and then continue to step 5.

IMPORTANT: If you have previously enabled any Internet-sharing proxy server software on any of your PCs, you must disable it now.

Some examples of Internet-sharing software are Internet LanBridge, Wingate, ICS, and Sygate. To disable your Internet-sharing software:

• If you are running Netscape Navigator, click Edit, Preferences, Advanced, and Proxies. Click Direct Connection to the Internet.

• If you are running Internet Explorer 5.x or higher, click Tools,

Settings, Control Panel, Internet Options, Connections, and LAN Settings. Remove checkmarks from all three boxes. Click the OK button to continue.

You must also disable any Internet log-on software (such as Ivasion Winpoet or Enternet 300) and any firewall software (such as ZoneAlarm and Watchdog) on all of your PCs.

Chapter 5:Configure the Router’s Basic Settings

This chapter will show you how to configure the Router to function in your network and gain access to the Internet through your Internet Service Provider (ISP). Detailed description of the Router’s web-based utility can be found in “Chapter 6: The Router’s Web-based Utility.”

The instructions from your ISP tell you how to set up your PC for Internet access. Because you are now using the Router to share Internet access among several computers, you will use the setup information to configure the Router instead of your PC. You only need to configure the Router once using the f irst computer you set up.

1. Open your web browser. Enter http://192.168.1.1 (the Router’s default IP address) in the web browser’s Address field. Press the Enter key.

2. An Enter Network Password window, shown in Figure 5-2, will appear. Windows XP users will see a Connect to 192.168.1.1 window, shown in Figure 5-3. Leav e the User Namefield empty, and enter adminin lowercase letters in the P assw or dfield (admin is the default passw ord). Then, click the OK button.

Figure 5-1

Figure 5-2 Figure 5-3

Note: For added security, you should change the password through the Password screen of the web-based utility.

Dual-Band Wireless A+B Broadband Router

Instant Wireless®Series

Automatic Configuration - DHCP

If you are connecting through DHCP or a dynamic IP address from your ISP, perform these steps:

A. Keep the default setting,Automatic

Configuration - DHCP, as the Configuration Type.

B. Click the Apply button to save the set-

ting, or click the Cancel button to clear the setting and start over. When you are finished, proceed to step 5.

Static (or Fixed) IP Address

If you are connecting through a static or fixed IP address from your ISP, perform these steps:

A. Select Static IP as the

Configuration Type.

B. Enter the Internet IP Address.

C. Enter the Subnet Mask.

D. Enter the Default Gateway.

E. Enter the DNS in the 1, 2,

and/or 3 fields. You need to enter at least one DNS address.

F. Click the Apply button to save

the settings, or click the Cancel button to clear the settings and start over. When you are finished, proceed to step 5.

PPPoE

If your DSL provider says that you are connecting through PPPoE (you use a user name and passw ord to access the Internet), perform these steps:

A. Select PPPoE as the

Configuration Type.

B. Enter the User Name.

C. Enter the Password.

D. Click the Apply button to save

the settings, or click the Cancel button to clear the settings and start over. When you are finished, proceed to step 5.

PPTP

PPTP is a service used in Europe only. If you are using a PPTP connection, check with your ISP for the necessary setup information.

After you have entered your setup information, click the Apply button to save the settings, or click the Cancel button to clear the settings and start over . When you are finished, proceed to step 5.

Figure 5-6

Figure 5-7

Important: If you enable PPPoE, remember to remove any PPPoE applications already installed on any of your PCs.

Figure 5-4

Figure 5-5

Dual-Band Wireless A+B Broadband Router

Chapter 6:The Router’s Web-based Utility

Use the Router’s web-based utility to administer it. This chapter will describe each web page in the Utility and each page’s key functions. The utility can be accessed via your web browser through use of a computer connected to the Router.

The Setup, Password, Status, DHCP, Log, and Help screens are available for basic setup. For advanced setup, click the Advanced tab to access these screens: Advanced Wireless (including 802.1x), Filters, Port Forwarding, Routing, DMZ Host, and MAC Address Clone.

To access the web-based utility, launch Internet Explorer or Netscape Navigator, and enter the Router’s default IP address, 192.168.1.1, in the Address field. Then press Enter.

A password request page, shown in Figure 6-2 will pop up. (W indows XP users will see a Connect to 192.168.1.1 window, shown in Figure 6-3). Leave the

User Name field blank, and enter admin (the default password) in the Password field. Then click the OK button.

Instant Wireless®Series

5. To conf igure the Router for your wireless network(s), perform these steps:

A. To enable 5GHz, 802.11a wireless networking, make sure the 5GHz,

802.11a Enable radio button is selected. Then click the Change 5GHz Settings button, and customize the SSID, Channel, and WEP encryption settings as needed. Then click the Apply button to save your changes. For more information, refer to “Chapter 6: The Router’s Web-based Utility.”

B. To enable 2.4GHz, 802.11b wireless networking, make sure the 2.4GHz,

802.11b Enable radio button is selected. Then click the Change 2.4GHz Settings button, and customize the SSID, Channel, and WEP encryption settings as needed. Then click the Apply button to save your changes. For more information, refer to “Chapter 6: The Router’s Web-based Utility.”

6. If you haven’t already done so, click the Apply button to save your Setup settings. Close the web browser.

7. Restart your computers so that they can obtain the Router’s new settings.

If you need more details or advanced setting information, please refer to “Chapter 6: The Router’s Web-based Utility” or the Linksys suppor t website at support.linksys.com.

Test the setup by opening your web browser from any computer and entering http://www.linksys.com/registration.

Congratulations! You’ve successfully configured the Router.

If you are unable to reach our website, you may want to review what you did in this section or refer to “Appendix A: Troubleshooting.”

Proceed to “Chapter 6: The Router’s Web-based Utility” for more details

and advanced settings information.

Overview

How to Access the Web-based Utility

Figure 6-1

Figure 6-2 Figure 6-3

Figure 5-8

Dual-Band Wireless A+B Broadband Router

Automatic Configuration - DHCP

By default, the Router’s Configuration Type is set to Automatic Configuration - DHCP, and it should be kept only if your ISP supports DHCP or you are connecting through a dynamic IP address.

T o apply any of the settings you change on this page, click the A ppl ybutton. To cancel any changes you’ve entered on this page, click the Cancel button. To get more information about the features, click the Help button.

Instant Wireless®Series

Figure 6-5

To apply any of the settings you change on a page, click the Apply button. To cancel any changes you’ve entered on any page, click the Cancelbutton. T o get additional information about any screen’s features, click the Help button.

The Setup screen is the first screen you see when you access the web-based utility. If you have already installed and set up the Router, you have already seen this screen and properly configured all of the screen’s values.

Firmware Version This shows the version and date of the fir mware you are using. Future versions of the Router’s f irmware will be posted and available for download on the Linksys website at www.linksys.com.

Host Name and Domain Name These f ields allow you to supply a host and domain name for the Router. Some ISPs, usually cable ISPs, require these names as identification. You may have to check with your ISP to see if your broadband Internet service has been configured with a host and domain name. In most cases, leaving these fields blank will work.

Configuration Type The Router supports four connection types: Automatic Configuration - DHCP, Static IP, PPPoE, and PPTP. Each Setup screen and available features will differ depending on what kind of connection type you select.

Setup

Note: You can verify that the Internet conf iguration settings are correct by successfully connecting to the Internet.

Note: For added security, you should always change the password through the Password screen of the web-based utility.

Dual-Band Wireless A+B Broadband Router

Instant Wireless®Series

PPPoE

Some DSL-based ISPs use PPPoE (Point-to-Point Protocol over Ethernet) to establish Internet connections. If you are connected to the Internet through a DSL line, check with your ISP to see if they use PPPoE. If they do, you will have to enable PPPoE.

User Name and Password Enter the User Name and Password provided by your ISP.

Connect on Demand: Max Idle Time You can configure the Router to cut the Internet connection after it has been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Router to automatically reestablish your connection as soon as you attempt to access the Internet again. If you wish to activ ate Connect on Demand, click the radio button. In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet connection terminates.

Figure 6-7

Static IP

If you are required to use a permanent IP address to connect to the Internet, then select Static IP.

Specify Internet IP Address This is the Router’s IP address, when seen from the WAN, or the Internet. Your ISP will provide you with the IP Address you need to specify here.

Subnet Mask This is the Router’s Subnet Mask, as seen by external users on the Internet (including your ISP). Your ISP will provide you with the Subnet Mask.

Default Gateway Your ISP will provide you with the Default Gateway Address, which is the ISP server’s IP address.

DNS 1 (Required) and DNS 2-3 (Optional) Your ISP will provide you with at least one DNS (Domain Name System) Ser ver IP Address.

Figure 6-6

Dual-Band Wireless A+B Broadband Router

Instant Wireless®Series

Specify Internet IP Address This is the Router’s IP address, when seen from the Internet. Your ISP will provide you with the IP Address you need to specify here.

Subnet Mask This is the Router’s Subnet Mask, as seen by external users on the Internet (including your ISP). Your ISP will provide you with the Subnet Mask.

Default Gateway Your ISP will provide you with the Default Gateway Address.

User Name and Password Enter the User Name and Password provided by your ISP.

Keep Alive Option: Redial Period If you select this option, the Router will periodically check your Internet connection. If you are disconnected, then the Router will automatically re-establish your connection. To use this option, click the radio button next to Keep Aliv e. To use this option, click the radio button next to Keep Aliv e. In the Redial Period field, you specify how often you w ant the Router to check the Internet connection. The default Redial Period is 30 seconds.

LAN IP Address and LAN Subnet Mask The values for the Router’s IP Address and Subnet Mask are shown here. The default values are 192.168.1.1 for the LAN IP Address and 255.255.255.0 for the Subnet Mask.

5GHz, 802.11a Wireless To enable 5GHz, 802.11a wireless netw orking, mak e sure the Enable radio button is selected. Click the Change 5GHz Settings button to customize the 802.11a configuration (see Figure 6-9).

Keep Alive Option: Redial Period If you select this option, the Router will periodically check your Internet connection. If you are disconnected, then the Router will automatically re-establish your connection. To use this option, click the radio button next to Keep Aliv e. In the Redial P eriodfield, you specify how often y ou w ant the Router to check the Internet connection. The default Redial Period is 30 seconds.

PPTP

Point to Point Tunneling Protocol (PPTP) is a ser vice that applies to connections in Europe only.

Figure 6-8

Important: For ADSL users, if you enable PPPoE, remember to remove an y PPPoE applications that are already installed on any of your PCs.

Dual-Band Wireless A+B Broadband Router

Turbo Mode This enables high-speed connections, but severely limits range. Turbo Mode must be enabled on both the Router and the wireless PCs to function. Turbo Mode is not compatible with Windows XP and functions only with Linksys 5GHz, 802.11a wireless adapters.

Select Enable to increase the speed of your wireless transmissions up to 72 Mbps. Keep in mind that the Router’s range diminishes in Turbo Mode. If you do not wish to utilize Turbo Mode, select Disable.

Channel Select the appropriate channel from the list provided to correspond with your network settings, between 36 and 64. All devices in your wireless network must use the same channel in order to function correctly. If you want the Router to automatically scan for a clear channel, then click the checkbox.

WEP (Encryption) An acronym for Wired Equivalent Privacy, WEP is an encryption method used to protect your wireless data communications. WEP uses 64-bit, 128-bit, or 152-bit keys to provide access control to your network and encryption security for every data transmission. To decode a data transmission, each device in a network must use an identical key. Higher encryption levels offer higher levels of security, but due to the complexity of the encryption, they may decrease network performance. Click the Edit WEPSettings button to configure the WEP keys for your 5GHz,

802.11a network (see Figure 6-10).

Check all the values, and click theApplybutton to sav e your 5GHz, 802.11a settings.To cancel any changes you’ve entered on this page, click the Cancel button. To get more information about the features, click the Help button.

Instant Wireless®Series

2.4GHz 802.11b Wireless To enable 2.4GHz, 802.11b wireless networking,

make sure the Enable radio button is selected. Click the Change 2.4GHz Settings button to customize the 802.11b configuration (see Figure 6-11).

5GHz, 802.11a

The 5GHz, 802.11a screen allows you to configure your 5GHz, 802.11a network settings.

SSID The SSID is the network name shared among all points in a wireless network. The SSID must be identical for all points in the wireless network. It is case-sensitive and must not exceed 32 characters (use any of the characters on the keyboard). Make sure this setting is the same for all points in your wireless network. For added security, you should change the default SSID (linksys) to a unique name.

Note: If Turbo Mode is enabled, then auto-scan will not function, and you must select one of the following channels: 42, 50, or 58.

Note: If auto-scan is enabled , then y ou cannot specify a channel setting.

Figure 6-9

Dual-Band Wireless A+B Broadband Router

Instant Wireless®Series

5GHz, 802.11a (WEP)

The 5GHz, 802.11a (WEP) screen allows you to configure your 5GHz,

802.11a WEP settings. WEP encryption should always be enabled to increase the security of your wireless network.

WEP Encryption Keys 1-4 offer 64-bit, 128-bit, or 152-bit encryption; select the type of encryption you want from the drop-down box. To disable WEP Encr yption, select Disable.

Default Transmit Key Select which WEP key (1-4) will be used when the Router sends data. Make sure the receiver is using the same key.

Keys 1-4 WEP keys enable you to create an encryption scheme for wireless LAN transmissions. Manually enter a set of values. (Do not leave a key field blank, and do not enter all zeroes. These are not valid key values.) Keys 1-4 offer 64-bit, 128-bit, or 152-bit encryption.

If you are using 64-bit WEP encryption, then the key must be exactly 10 hexadecimal characters in length. If you are using 128-bit WEP encryption, then the key must be exactly 26 hexadecimal characters in length. If you are using 152-bit WEP encryption, then the key must be exactl y 32 he xadecimal characters in length. Valid hexadecimal characters are “0”-“9” and “A”-“F”.

Check all the values, and click theApplybutton to sav e your 5GHz, 802.11a WEP settings. To cancel any changes you’ve entered on this page, click the Cancel button. To get more information about the features, click the Help button.

2.4GHz, 802.11b

The 2.4GHz, 802.11b screen allows you to configure your 2.4GHz, 802.11b network settings.

Channel Select the appropriate channel from the list provided to correspond with your network settings, between 1 and 11 (in North America). All devices in your wireless network must use the same channel in order to function correctly.

Figure 6-11

Figure 6-10

+ 48 hidden pages