Linksys WRT350N User Manual
2.4
WIRELESS
GHz
Wireless-N
Gigabit Router with
User Guide
Storage Link
Model No.
WRT350N
Wireless-N Gigabit Router with Storage Link
Copyright and Trademarks
Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco
Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2006 Cisco Systems, Inc. All
rights reserved. Other brands and product names are trademarks or registered trademarks of their respective
holders.
WARNING: This product contains chemicals, including lead, known
to the State of California to cause cancer, and birth defects or other
reproductive harm. Wash hands after handling.
How to Use This User Guide
This User Guide has been designed to make understanding networking with the Wireless-N Gigabit Router with
Storage Link easier than ever. Look for the following items when reading this User Guide:
This checkmark means there is a note of interest and is
something you should pay special attention to while using
the Wireless-N Gigabit Router with Storage Link.
This exclamation point means there is a caution or warning
and is something that could damage the Router.
This question mark provides you with a reminder about
something you might need to do while using the Wireless-N
Gigabit Router with Storage Link.
In addition to these symbols, there are definitions for technical terms that are presented like this:
word: definition.
Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like
this:
Figure 0-1: Sample Figure Description
Figure numbers and descriptions can also be found in the “List of Figures” section in the “Table of Contents”.
WRT350N-UG-60726NC SW
Wireless-N Gigabit Router with Storage Link
Table of Contents
Chapter 1: Introduction 1
Welcome 1
What’s in this User Guide? 2
Chapter 2: Planning Your Wireless Network 4
Network Topology 4
Ad-Hoc versus Infrastructure Mode 4
Network Layout 5
Chapter 3: Getting to Know the Wireless-N Gigabit Router with Storage Link 6
The Back Panel 6
The Front Panel 7
The Top Panel 7
Chapter 4: Connecting the Wireless-N Gigabit Router with Storage Link 8
Hardware Installation 8
Chapter 5: Configuring the Wireless-N Gigabit Router with Storage Link 9
Overview 9
How to Access the Web-based Utility 11
The Setup Tab - Basic Setup 11
The Setup Tab - DDNS 17
The Setup Tab - MAC Address Clone 19
The Setup Tab - Advanced Routing 20
The Wireless Tab - Basic Wireless Settings 22
The Wireless Tab - Wireless Security 23
The Wireless Tab - Wireless MAC Filter 26
The Wireless Tab - Advanced Wireless Settings 27
The Security Tab - Firewall 29
The Security Tab - VPN Passthrough 30
The Storage Tab - Disk 31
The Storage Tab - Share 32
The Storage Tab - Administration 33
The Storage Tab - Media Server 35
The Access Restrictions Tab - Internet Access Policy 37
The Applications & Gaming Tab - Single Port Forwarding 39
Wireless-N Gigabit Router with Storage Link
The Applications & Gaming Tab - Port Range Forwarding 40
The Applications & Gaming Tab - Port Range Triggering 41
The Applications & Gaming Tab - DMZ 42
The Applications and Gaming Tab - QoS 43
The Administration Tab - Management 46
The Administration Tab - Log 48
The Administration Tab - Diagnostics 49
The Administration Tab - Factory Defaults 50
The Administration Tab - Firmware Upgrade 51
The Status Tab - Router 52
The Status Tab - Local Network 53
The Status Tab - Wireless 54
Appendix A: Troubleshooting 55
Common Problems and Solutions 55
Frequently Asked Questions 63
Appendix B: Wireless Security 69
Security Precautions 69
Security Threats Facing Wireless Networks 69
Appendix C: Upgrading Firmware 72
Appendix D: Windows Help 73
Appendix E: Finding the MAC Address and IP Address for your
Ethernet Adapter 74
Windows 98SE or Me Instructions 74
Windows 2000 or XP Instructions 75
For the Router’s Web-based Utility 75
Appendix F: Glossary 76
Appendix G: Specifications 81
Appendix H: Warranty Information 83
Appendix I: Regulatory Information 84
Appendix J: Contact Information 90
Wireless-N Gigabit Router with Storage Link
List of Figures
Figure 3-1: The Router’s Back Panel 6
Figure 3-2: The Router’s Front Panel 7
Figure 3-3: The Router’s Top Panel 7
Figure 4-1: Connect the USB cable 8
Figure 4-2: Connect the internet 8
Figure 4-3: Connect the ethernet 8
Figure 4-4: Connect the power 8
Figure 5-1: Router Login 11
Figure 5-2: Setup Tab - Basic Setup (Automatic Configuration - DHCP) 11
Figure 5-3: Static IP 12
Figure 5-4: PPPoE 12
Figure 5-5: PPTP 13
Figure 5-6: Telstra Cable 14
Figure 5-7: L2TP 14
Figure 5-8: DHCP Reservation 16
Figure 5-9: Setup Tab - DynDDNS.org 17
Figure 5-10: Setup Tab - TZO.com 18
Figure 5-11: Setup Tab - MAC Clone 19
Figure 5-12: Setup Tab - Advanced Routing 20
Figure 5-13: Routing Table 21
Figure 5-14: Wireless Tab - Basic Wireless Settings 22
Figure 5-15: Wireless Tab - Wireless Security (PSK-Personal) 23
Figure 5-16: Wireless Security - PSK2-Personal 23
Figure 5-17: Wireless Security - PSK-Enterprise 24
Figure 5-18: Wireless Security - PSK2-Enterprise 24
Figure 5-19: Wireless Security - RADIUS 25
Figure 5-20: Wireless Security - WEP 25
Figure 5-21: Wireless Tab - Wireless MAC Filter 26
Figure 5-22: Wireless Client List 26
Figure 5-23: Wireless Tab - Advanced Wireless Settings 27
Figure 5-24: Security Tab - Firewall 29
Wireless-N Gigabit Router with Storage Link
Figure 5-25: VPN Passthrough 30
Figure 5-26: Storage Tab - Disk 31
Figure 5-27: Storage Tab - Claim Disk 31
Figure 5-28: Storage Tab - Claimed Disk 31
Figure 5-29: Storage Tab - Share Management 32
Figure 5-30: Share Properties 32
Figure 5-31: Storage Tab - Administration 33
Figure 5-32: User Properties 33
Figure 5-33: User Properties 34
Figure 5-34: Storage Tab - UPnP Media Server 35
Figure 5-35: Partition List 35
Figure 5-36: FTP Server 36
Figure 5-37: FTP Access 36
Figure 5-38: Access Restrictions Tab - Internet Access Policy 37
Figure 5-39: Summary 37
Figure 5-40: List of PCs 38
Figure 5-41: Applications & Gaming Tab - Single Port Forwarding 39
Figure 5-42: Applications & Gaming Tab - Port Range Forwarding 40
Figure 5-43: Applications & Gaming Tab - Port Range Triggering 41
Figure 5-44: Applications & Gaming Tab - DMZ 42
Figure 5-45: DHCP Client Table 42
Figure 5-46: Applications & Gaming Tab - QoS (Applications) 43
Figure 5-47: QoS - Applications (Add a New Application) 44
Figure 5-48: QoS - Online Games 44
Figure 5-49: QoS - MAC Address 44
Figure 5-50: QoS - MAC Address 44
Figure 5-51: QoS - Voice Device 45
Figure 5-52: Administration Tab - Management 46
Figure 5-53: Administration Tab - Log 48
Figure 5-54: View Log 48
Figure 5-55: Administration Tab - Diagnostics 49
Figure 5-56: Ping Test 49
Figure 5-57: Traceroute Test 49
Figure 5-58: Administration Tab - Factory Defaults 50
Wireless-N Gigabit Router with Storage Link
Figure 5-59: Administration Tab - Firmware Upgrade 51
Figure 5-60: Status Tab - Router 52
Figure 5-61: Status Tab - Local Network 53
Figure 5-62: DHCP Client Table 53
Figure 5-63: Status Tab - Wireless Network 54
Figure C-1: Firmware Upgrade 72
Figure E-1: IP Configuration Screen 74
Figure E-2: MAC Address/Adapter Address 74
Figure E-3: MAC Address/Physical Address 74
Figure E-4: Wireless MAC Filter 75
Figure E-5: MAC Address Cloning 75
Wireless-N Gigabit Router with Storage Link
Chapter 1: Introduction
Welcome
The Wireless-N Gigabit Router with Storage Link is really four devices in one box. First, there's the Wireless
Access Point, which lets you connect to the network without wires. There's also a built-in 4-port full-duplex
10/100 Switch to connect your wired-Ethernet devices together. The Router function ties it all together and lets
your whole network share a high-speed cable or DSL Internet connection.
We've also included a Storage Link that lets you easily add gigabytes of storage space onto your network using
readily available USB 2.0 hard drives -- or plug in a USB flash disk for a convenient way to access your portable
data files. The built-in Media Server streams music, video, and photos from the attached storage device to any
UPnP compatible media adapter. And you can get to your files from anywhere in the world through the Internet.
The Access Point built into the Router uses the very latest wireless networking technology, Wireless-N (draft
802.11n). By overlaying the signals of multiple radios, Wireless-N's "Multiple In, Multiple Out" (MIMO) technology
multiplies the effective data rate. Unlike ordinary wireless networking technologies that are confused by signal
reflections, MIMO actually uses these reflections to increase the range and reduce "dead spots" in the wireless
coverage area. The robust signal travels farther, maintaining wireless connections up to 4 times farther than
standard Wireless-G.
With Wireless-N, the farther away you are, the more speed advantage you get. It works great with standard
Wireless-G and -B equipment, but when both ends of the wireless link are Wireless-N, the router can increase the
throughput even more by using twice as much radio band, yielding speeds up to 12 times as fast as standard
Wireless-G. But unlike other speed-enhanced technologies, Wireless-N can dynamically enable this
double-speed mode for Wireless-N devices, while still connecting to other wireless devices at their respective
fastest speeds. In congested areas, the "good neighbor" mode ensures that the Router checks for other wireless
devices in the area before gobbling up the radio band.
To help protect your data and privacy, the Router can encode all wireless transmissions with industrial-strength
256-bit encryption. It can serve as your network's DHCP Server, has a powerful SPI firewall to protect your PCs
against intruders and most known Internet attacks, and supports VPN pass-through. Configuration is a snap with
the web browser-based configuration utility.
spi (stateful packet inspection) firewall: a technology
that inspects incoming packets of information before
allowing them to enter the network.
firewall: Security measures that protect the
resources of a local network from intruders.
nat (network address translation): NAT technology
translates IP addresses of a local area network to a
different IP address for the Internet.
lan (local area network): The computers and
networking products that make up the network in
your home or office.
The incredible speed of Wireless-N makes it ideal for media-centric applications like streaming video, gaming,
and Voice over IP telephony, and gives you plenty of headroom to run multiple media-intense data streams
through the network at the same time, with no degradation in performance. With the Linksys Wireless-N Gigabit
Router with Storage Link at the center of your home or office network, you can easily add storage, share a highspeed Internet connection, files, printers and multi-player games, and run media-intensive applications at faster
than 10/100 wired network speeds, without the hassle of stringing wires!
Chapter 1: Introduction
Welcome
1
Wireless-N Gigabit Router with Storage Link
What’s in this User Guide?
This user guide covers the steps for setting up and using the Wireless-N Gigabit Router with Storage Link.
• Chapter 1: Introduction
This chapter describes the Router’s applications and this User Guide.
• Chapter 2: Planning Your Wireless Network
This chapter describes the basics of wireless networking.
• Chapter 3: Getting to Know the Wireless-N Gigabit Router with Storage Link
This chapter describes the physical features of the Router.
• Chapter 4: Connecting the Wireless-N Gigabit Router with Storage Link
This chapter instructs you on how to connect the Router to your network.
• Chapter 5: Configuring the Wireless-N Gigabit Router with Storage Link
This chapter explains how to use the Web-based Utility to configure the settings on the Wireless-N Gigabit
Router with Storage Link.
• Appendix A: Troubleshooting
This appendix describes some problems and solutions, as well as frequently asked questions, regarding
installation and use of the Wireless-N Gigabit Router with Storage Link.
• Appendix B: Wireless Security
This appendix explains the risks of wireless networking and some solutions to reduce the risks.
• Appendix C: Upgrading Firmware
This appendix instructs you on how to upgrade the firmware on the Router should you need to do so.
• Appendix D: Windows Help
This appendix describes how you can use Windows Help for instructions about networking, such as installing
the TCP/IP protocol.
• Appendix E: Finding the MAC Address and IP Address for your Ethernet Adapter
This appendix describes how to find the MAC address for your computer’s Ethernet adapter so you can use
the MAC filtering and/or MAC address cloning feature of the Router.
• Appendix F: Glossary
This appendix gives a brief glossary of terms frequently used in networking.
Chapter 1: Introduction
What’s in this User Guide?
2
Wireless-N Gigabit Router with Storage Link
• Appendix G: Specifications
This appendix provides the technical specifications for the Router.
• Appendix H: Warranty Information
This appendix supplies the warranty information for the Router.
• Appendix I: Regulatory Information
This appendix supplies the regulatory information regarding the Router.
• Appendix J: Contact Information
This appendix provides contact information for a variety of Linksys resources, including Technical Support.
Chapter 1: Introduction
What’s in this User Guide?
3
Wireless-N Gigabit Router with Storage Link
Chapter 2: Planning Your Wireless Network
Network Topology
A wireless local area network (WLAN) is exactly like a regular local area network (LAN), except that each
computer in the WLAN uses a wireless device to connect to the network. Computers in a WLAN share the same
frequency channel and SSID, which is an identification name shared by the wireless devices belonging to the
same wireless network.
Ad-Hoc versus Infrastructure Mode
ssid (service set identifier): your wireless network’s name.
Unlike wired networks, wireless networks have two different modes in which they may be set up: infrastructure
and ad-hoc. An infrastructure configuration is a WLAN and wired LAN communicating to each other through an
access point. An ad-hoc configuration is wireless-equipped computers communicating directly with each other.
Choosing between these two modes depends on whether or not the wireless network needs to share data or
peripherals with a wired network or not.
If the computers on the wireless network need to be accessible by a wired network or need to share a peripheral,
such as a printer, with the wired network computers, the wireless network should be set up in Infrastructure
mode. The basis of Infrastructure mode centers around a wireless router or an access point, such as the
Wireless-N Gigabit Router with Storage Link, which serves as the main point of communications in a wireless
network. The Router transmits data to PCs equipped with wireless network adapters, which can roam within a
certain radial range of the Router. You can arrange the Router and multiple access points to work in succession to
extend the roaming range, and you can set up your wireless network to communicate with your Ethernet
hardware as well.
If the wireless network is relatively small and needs to share resources only with the other computers on the
wireless network, then the Ad-Hoc mode can be used. Ad-Hoc mode allows computers equipped with wireless
transmitters and receivers to communicate directly with each other, eliminating the need for a wireless router or
access point. The drawback of this mode is that in Ad-Hoc mode, wireless-equipped computers are not able to
communicate with computers on a wired network. And, of course, communication between the wirelessequipped computers is limited by the distance and interference directly between them.
infrastructure: a wireless network that is bridged
to a wired network via an access point.
ad-hoc: a group of wireless devices
communicating directly to each other (peer-topeer) without the use of an access point.
Chapter 2: Planning Your Wireless Network
Network Topology
4
Wireless-N Gigabit Router with Storage Link
Network Layout
The Wireless-N Gigabit Router with Storage Link has been specifically designed for use with your Wireless-N,
Wireless-G, and Wireless-B products. It will work with notebook adapters for your laptop computers, PCI adapters
for your desktop computers, and USB adapters for your USB connectivity needs. The Router can also
communicate with other devices, such as wireless print servers and bridges.
When you wish to connect your wireless network to your wired network, you can use the Router’s four local
Ethernet ports. To add more ports, connect one of the Router's local ports to any Linksys switch.
With these, and many other, Linksys products, your networking options are limitless. Go to the Linksys website at
www.linksys.com for more information about products that work with the Wireless-N Gigabit Router with Storage
Link.
Chapter 2: Planning Your Wireless Network
Network Layout
5
Wireless-N Gigabit Router with Storage Link
Chapter 3: Getting to Know the Wireless-N Gigabit Router with Storage Link
The Back Panel
The Router's ports, where the cables are connected, and Reset button are located on the back panel.
Figure 3-1: The Router’s Back Panel
USB The USB port connects your Router to your wired PC or other USB network devices.
INTERNET The Internet port is where you will connect your broadband modem.
ETHERNET 1, 2, 3, 4 These ports (1, 2, 3, 4) connect the Router to your wired PCs and other Ethernet network
devices.
Reset Button There are two ways to reset the Router's factory defaults. Either press the Reset button,
for approximately five seconds, or restore the defaults from the Administration - Factory
Defaults tab of the Router's Web-based Utility.
Power The Power port is where you will connect the power adapter.
Chapter 3: Getting to Know the Wireless-N Gigabit Router with Storage Link
The Back Panel
IMPORTANT: Resetting the Router will erase all of
your settings (Internet connection, wireless
security, and other settings) and replace them
with the factory defaults. Do not reset the Router
if you want to retain these settings.
6
Wireless-N Gigabit Router with Storage Link
The Front Panel
The Router’s LEDs are located on the front panel.
Figure 3-2: The Router’s Front Panel
POWER Green. The POWER LED lights up and will stay on while the Router is powered on.
ETHERNET 1, 2, 3, 4 Green, Orange. These numbered LEDs, corresponding with the numbered ports on the
Router’s back panel, serve three purposes: (1) The green LED lights up when the Router is
connected to a device through the corresponding port at 10/100, (2) The orange LED lights
up when you are connected at 1,000 Mbps (1 Gigabit), and (3) If the LED is flashing, then
the Router is sending or receiving data over that port.
INTERNET Green. The INTERNET LED lights up when there is a connection through the Internet port.
Button
WIRELESS Green. The WIRELESS LED lights up when there is a wireless connection. If the LED is
flashing, the Router is sending or receiving data over the wireless network.
USB Green. The USB LED lights up when a USB drive is connected through the USB port. If the
LED is flashing, the Router is actively sending or receiving data over the USB connection.
SECURITY Green. The SECURITY LED indicates when wireless security is enabled.
The Top Panel
The Router has a button reserved for a future function.
Chapter 3: Getting to Know the Wireless-N Gigabit Router with Storage Link
The Front Panel
Figure 3-3: The Router’s Top Panel
7
Wireless-N Gigabit Router with Storage Link
Chapter 4: Connecting the Wireless-N Gigabit Router with Storage Link
Hardware Installation
1. Make sure that all of your hardware is powered off, including the broadband modem and PCs.
2. Connect your USB cable tot he Router’s USB port.
Figure 4-1: Connect the USB cable
3. Connect your broadband modem’s Ethernet cable to the Router’s Internet port.
4. Connect one end of an Ethernet network cable to one of the numbered ports on the back of the Router.
Connect the other end to an Ethernet port on a network device, e.g., a PC, print server, or switch.
Repeat this step to connect more PCs or other network devices to the Router.
5. Power on the broadband modem.
6. Connect the included power adapter to the Router’s Power port, and then plug the power adapter into an
electrical outlet. The Power LED on the front panel will light up when the adapter is connected properly.
Figure 4-2: Connect the internet
7. Power on your PC(s).
8. Locate an optimum location for the Router. The best place for the Router is usually at the center of your
wireless network, with line of sight to all of your wireless devices.
Proceed to “Chapter 5: Configuring the Wireless-N Gigabit Router with Storage Link”.
IMPORTANT: Make sure you use the power
adapter that is supplied with the Router. Use of a
different power adapter could damage the Router.
Chapter 4: Connecting the Wireless-N Gigabit Router with Storage Link
Hardware Installation
Figure 4-3: Connect the ethernet
Figure 4-4: Connect the power
8
Wireless-N Gigabit Router with Storage Link
Chapter 5: Configuring the Wireless-N Gigabit Router with Storage Link
Overview
Linksys recommends using the Setup CD-ROM for first-time installation of the Router. If you do not wish to run
the Setup Wizard on the Setup CD-ROM, then you can use the Web-based Utility to configure the Router. For
advanced users, you may configure the Router’s advanced settings through the Web-based Utility.
This chapter will describe each web page on the Utility and each page’s key functions. The Utility can be
accessed via your web browser through use of a computer connected to the Router. For a basic network setup,
most users only have to use the following screens of the Utility:
• Basic Setup. On the Basic Setup screen, enter the Internet connection settings provided by your Internet
Service Provider (ISP). If you do not have this information, you can call your ISP to request the settings. When
you have the setup information, then you can configure the Router.
• Management. Click the Administration tab and then the Management tab. The Router’s default password is
admin. To secure the Router, change the Password from its default.
• Wireless. On the Basic Wireless Settings screen, set the basic configuration for your wireless network.
There are eight main tabs: Setup, Wireless, Security, Storage, Access Restrictions, Applications & Gaming,
Administration, and Status. Additional tabs will be available after you click one of the main tabs.
Setup
• Basic Setup. Enter the Internet connection and network settings on this screen.
• DDNS. Enable the Router’s Dynamic Domain Name System (DDNS) feature on this screen.
• MAC Address Clone. If you need to clone a MAC address onto the Router, use this screen.
• Advanced Routing. Use this screen to alter dynamic and static routing configurations.
Chapter 5: Configuring the Wireless-N Gigabit Router with Storage Link
Overview
9
Wireless-N Gigabit Router with Storage Link
Wireless
• Basic Wireless Settings. Enter the basic settings for your wireless network on this screen.
• Wireless Security. Enable and configure the security settings for your wireless network.
• Wireless MAC Filter. Wireless access can be filtered by using the MAC addresses of the wireless devices
transmitting within your network’s radius.
• Advanced Wireless Settings. For advanced users, you can alter data transmission settings on this screen.
Security
• Firewall. You can enable or disable the Router’s firewall, as well as various filters.
• VPN Passthrough. To enable or disable IPSec, L2TP, and/or PPTP Passthrough, use this screen.
Storage
• Disk. Describes the disk currently attached to the Router.
• Share. Controls access to the partition of the disk attached to the Router.
• Administration. Manages the user and groups of users that can access the shares.
• Media Server. Scans for contents using a built-in media server.
• FTP Server. Creates an FTP server that can be accessed through the Internet.
Access Restrictions
Internet Access Policy. Create policies to control Internet access for your local network users.
Applications & Gaming
• Single Port Forwarding. This allows you to do port mapping and forwarding for a single service port.
• Port Range Forwarding. Set up public services or other specialized Internet applications on your network.
• Port Range Triggering. Configure the Router to watch outgoing data for specific port numbers.
Chapter 5: Configuring the Wireless-N Gigabit Router with Storage Link
Overview
10
Wireless-N Gigabit Router with Storage Link
• DMZ. Click this tab to allow one local user to be exposed to the Internet for use of special-purpose services.
• QoS. Quality of Service (QoS) ensures better service to high-priority types of network traffic.
Administration
• Management. On this screen, alter the Router’s password, access privileges, and UPnP settings. You can also
use this screen to back up and restore the Router’s configuration file.
• Log. If you want to view or save activity logs, click this tab.
• Diagnostics. If you want to run a ping or traceroute test, then use this screen.
• Factory Defaults. If you want to restore the Router’s factory defaults, then use this screen.
• Firmware Upgrade. Click this tab if you want to upgrade the Router’s firmware.
Status
• Router. This screen provides status information about the Router.
• Local Network. This provides status information about the local network.
• Wireless Network. This provides status information about the wireless network.
How to Access the Web-based Utility
To access the Web-based Utility of the Router, launch Internet Explorer or Netscape Navigator, and enter the
Router’s default IP address, 192.168.1.1, in the Address field. Press the Enter key.
A screen will appear asking you for your User name and Password. Leave the User Name field blank. Enter admin
in the Password field. Then click the OK button.
Make the necessary changes through the Utility. When you have finished making changes to a screen, click the
Save Settings button to save the changes, or click the Cancel Changes button to undo your changes. For
information on a tab, click Help.
The Setup Tab - Basic Setup
The Basic Setup screen is the first screen you see when you access the Web-based Utility.
Figure 5-1: Router Login
Figure 5-2: Setup Tab - Basic Setup
(Automatic Configuration - DHCP)
NOTE: Some of these connection types may not
be available in your area.
Chapter 5: Configuring the Wireless-N Gigabit Router with Storage Link
How to Access the Web-based Utility
11
Wireless-N Gigabit Router with Storage Link
Internet Setup
The Internet Setup section configures the Router for your Internet connection type. This information can be
obtained from your ISP.
Internet Connection Type
The Router supports six connection types: Automatic Configuration - DHCP, Static IP, PPPoE, PPTP, Telstra Cable,
and L2TP. Each Basic Setup screen and available features will differ depending on what kind of connection type
you select.
Automatic Configuration - DHCP
By default, the Router’s Internet Connection Type is set to Automatic Configuration - DHCP, and it should be
used only if your ISP supports DHCP or you are connecting through a dynamic IP address.
Static IP
If you are required to use a permanent IP address, then select Static IP.
Internet IP Address. This is the IP address that the Router has, when seen from the Internet. Your ISP will
provide you with the IP address you need to specify here.
Subnet Mask. This is the Router’s Subnet Mask, as seen by external users on the Internet (including your
ISP). Your ISP will provide you with the Subnet Mask.
Default Gateway. Your ISP will provide you with the Default Gateway Address.
DNS 1-3. Your ISP will provide you with at least one DNS (Domain Name System) Server IP Address.
PPPoE
Some DSL-based ISPs use PPPoE (Point-to-Point Protocol over Ethernet) to establish Internet connections for
end-users. If you use a DSL line, check with your ISP to see if they use PPPoE. If they do, you will have to
enable it.
Figure 5-3: Static IP
static ip address: a fixed address
assigned to a computer or device
connected to a network.
subnet mask: an address code that
determines the size of the network
default gateway: a device that forwards
Internet traffic from your local area network
Figure 5-4: PPPoE
User Name and Password. Enter the User Name and Password provided by your ISP.
IMPORTANT: For DSL users, if you need to enable PPPoE support, remember to remove any
PPPoE applications that are installed on your PCs.
Chapter 5: Configuring the Wireless-N Gigabit Router with Storage Link
The Setup Tab - Basic Setup
pppoe: a type of broadband connection that
provides authentication (username and
password) in addition to data transport
12
Wireless-N Gigabit Router with Storage Link
Service Name. If provided by your ISP, enter the Service Name.
Connect on Demand and Max Idle Time. You can configure the Router to cut the Internet connection after it
has been inactive for a specific period of time (Max Idle Time). If your Internet connection has been
terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your
connection as soon as you attempt to access the Internet again. To use Connect on Demand, click the radio
button. If you want your Internet connection to remain on at all times, enter 0 in the Max Idle Time field.
Otherwise, enter the number of minutes you want to have elapsed before your Internet access disconnects.
Keep Alive and Redial Period. This option keeps your Internet access connected indefinitely, even when it
sits idle. If you select this option, the Router will periodically check your Internet connection. If the connection
is down, then the Router will automatically re-establish the connection. To use this option, click the radio
button next to Keep Alive. The default Redial Period is 30 seconds.
Click the Save Settings button. Then click the Status tab, and click the Connect button.
PPTP
Point-to-Point Tunneling Protocol (PPTP) is a service that applies to connections in Europe and Israel only.
Server IP Address. This is the IP address that the Router has, when seen from the Internet. Your ISP will
provide you with the IP address you need to specify here.
Subnet Mask. This is the Router’s Subnet Mask, as seen by external users on the Internet (including your
ISP). Your ISP will provide you with the Subnet Mask.
Figure 5-5: PPTP
Default Gateway. Your ISP will provide you with the Default Gateway Address.
User Name and Password. Enter the User Name and Password provided by your ISP.
Connect on Demand and Max Idle Time. You can configure the Router to cut the Internet connection after it
has been inactive for a specific period of time (Max Idle Time). If your Internet connection has been
terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your
connection as soon as you attempt to access the Internet again. To use Connect on Demand, click the radio
button. If you want your Internet connection to remain on at all times, enter 0 in the Max Idle Time field.
Otherwise, enter the number of minutes you want to have elapsed before your Internet access disconnects.
Keep Alive and Redial Period. This option keeps your Internet access connected indefinitely, even when it
sits idle. If you select this option, the Router will periodically check your Internet connection. If the connection
is down, then the Router will automatically re-establish the connection. To use this option, click the radio
button next to Keep Alive. The default Redial Period is 30 seconds.
Chapter 5: Configuring the Wireless-N Gigabit Router with Storage Link
The Setup Tab - Basic Setup
13
Wireless-N Gigabit Router with Storage Link
Click the Save Settings button. Then click the Status tab, and click the Connect button.
Tels tra C able
Telstra Cable is a service used in Australia only. Check with your ISP for the necessary setup information.
Server IP Address. This is the IP address that the Router has, when seen from the Internet. Your ISP will
provide you with the IP address you need to specify here.
User Name and Password. Enter the User Name and Password provided by your ISP.
Click the Save Settings button. Then click the Status tab, and click the Connect button.
L2TP
Layer 2 Tunneling Protocol (L2TP) is a service that tunnels Point-to-Point Protocol (PPP) across the Internet. It
is used mostly in European countries. Check with your ISP for the necessary setup information.
Server IP Address. This is the IP address that the Router has, when seen from the Internet. Your ISP will
provide you with the IP address you need to specify here.
User Name and Password. Enter the User Name and Password provided by your ISP.
Connect on Demand and Max Idle Time. You can configure the Router to cut the Internet connection after it
has been inactive for a specific period of time (Max Idle Time). If your Internet connection has been
terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your
connection as soon as you attempt to access the Internet again. To use Connect on Demand, click the radio
button. If you want your Internet connection to remain on at all times, enter 0 in the Max Idle Time field.
Otherwise, enter the number of minutes you want to have elapsed before your Internet access disconnects.
Keep Alive and Redial Period. This option keeps your Internet access connected indefinitely, even when it
sits idle. If you select this option, the Router will periodically check your Internet connection. If the connection
is down, then the Router will automatically re-establish the connection. To use this option, click the radio
button next to Keep Alive. The default Redial Period is 30 seconds.
Figure 5-6: Telstra Cable
Figure 5-7: L2TP
packet: a unit of data sent over a network.
Click the Save Settings button. Then click the Status tab, and click the Connect button.
Optional Settings
Some of these settings may be required by your ISP. Verify with your ISP before making any changes.
Chapter 5: Configuring the Wireless-N Gigabit Router with Storage Link
The Setup Tab - Basic Setup
14
Wireless-N Gigabit Router with Storage Link
Host Name and Domain Name. Some ISPs require these names as identification. You may have to check with
your ISP to see if your broadband Internet service has been configured with a host and domain name. In most
cases, leaving these fields blank will work.
MTU. The MTU (Maximum Transmission Unit) setting specifies the largest packet size permitted for network
transmission. To manually set a value, select Manual and enter the value desired in the Size field. You should
leave this value in the 1200 to 1500 range. Most DSL users should use the value 1492. The default is Auto, which
allows the Router to select the best MTU for your Internet connection.
Network Setup
The Network Setup section allows you to change the Router’s local network settings.
Router IP
The Router’s Local IP Address and Subnet Mask are shown here. In most cases, you should keep the defaults.
Local IP Address. The default value is 192.168.1.1.
Subnet Mask. The default value is 255.255.255.0.
DHCP Server Setting
The Router can be used as a Dynamic Host Configuration Protocol (DHCP) server for your network. A DHCP server
automatically assigns an IP address to each computer on your network. Unless you already have one, it is highly
recommended that you leave the Router enabled as a DHCP server.
DHCP Server. DHCP is enabled by factory default. If you already have a DHCP server on your network, set the
Router’s DHCP option to Disabled. If you disable DHCP, remember to assign a static IP address to the Router.
Start IP Address. Enter a value for the DHCP server to start with when issuing IP addresses. Because the default
IP address for the Router is 192.168.1.1, the Start IP Address must be 192.168.1. 2 or greater, but smaller than
192.168.1.254. The default Start IP Address is 192.168.1.100.
Maximum Number of Users (Optional). Enter the maximum number of PCs that you want the DHCP server to
assign IP addresses to. This number cannot be greater than 253. The default is 50.
Client Lease Time. The Client Lease Time is the amount of time a network user will be allowed connection to the
Router with their current dynamic IP address. Enter the amount of time, in minutes, that the user will be “leased”
this dynamic IP address. After the dynamic IP address has expired, the user will be automatically assigned a new
dynamic IP address. The default is 0 minutes, which means one day.
Chapter 5: Configuring the Wireless-N Gigabit Router with Storage Link
The Setup Tab - Basic Setup
dynamic ip address: a temporary IP
address assigned by a DHCP server.
15
Wireless-N Gigabit Router with Storage Link
Static DNS 1-3. The Domain Name System (DNS) is how the Internet translates domain or website names into
Internet addresses or URLs. Your ISP will provide you with at least one DNS Server IP Address. You can enter up to
three DNS Server IP Addresses here. The Router will use these for quicker access to functioning DNS servers.
WINS. The Windows Internet Naming Service (WINS) converts NetBIOS names to IP addresses. If you use a WINS
server, enter that server’s IP address here. Otherwise, leave this field blank.
DHCP Reservation. Click the DHCP Reservation button if you want to assign a fixed local IP address to a MAC
address. You will see a list of DHCP clients with the following information: Client Name, Interface, IP Address, and
MAC Address. Click the Select checkbox to reserve a client’s IP address. Then click the Add Clients button.
If you want to manually assign an IP address, enter the client’s name in the Enter Client Name field. Enter the IP
address you want it to have in the Assign IP Address field. Enter its MAC Address in the To This MAC Address field.
Click the Add button.
A list of DHCP clients and their fixed local IP addresses will be displayed at the bottom of the screen. If you want
to remove a client from this list, click the Remove button.
When you have finished your changes, click the Save Settings button to save your changes. Click the Cancel
Changes button to cancel your changes. To view the most up-to-date information, click the Refresh button. To
exit this screen, click the Close button.
Time Setting
Time Zone. Select the time zone in which your network functions. If you want the Router to automatically adjust
the clock for daylight savings, then select the checkbox.
When you have finished making changes to this screen, click the Save Settings button to save the changes, or
click the Cancel Changes button to undo your changes. For more information, click Help.
Chapter 5: Configuring the Wireless-N Gigabit Router with Storage Link
The Setup Tab - Basic Setup
Figure 5-8: DHCP Reservation
NOTE: To test your settings, connect to the
Internet now.
16
Wireless-N Gigabit Router with Storage Link
The Setup Tab - DDNS
The Router offers a Dynamic Domain Name System (DDNS) feature. DDNS lets you assign a fixed host and domain
name to a dynamic Internet IP address. It is useful when you are hosting your own website, FTP server, or other
server behind the Router.
Before you can use this feature, you need to sign up for DDNS service at one of two DDNS service providers,
DynDNS.org or TZO.com. If you do not want to use this feature, keep the default setting, Disable.
DDNS
DDNS Service
If your DDNS service is provided by DynDNS.org, then select DynDNS.org from the drop-down menu. If your
DDNS service is provided by TZO, then select TZO.com. The features available on the DDNS screen will vary,
depending on which DDNS service provider you use.
DynDNS.org
Username, Password, and Host Name. Enter the settings of the account you set up with DynDNS.org.
System. Select the DynDNS service you use: Dynamic, Static, or Custom.
Figure 5-9: Setup Tab - DynDDNS.org
Mail Exchange (Optional). Enter the address of your mail exchange server, so e-mails to your DynDNS
address go to your mail server.
Backup MX. This feature allows the mail exchange server to be a backup. To enable this feature, keep the
default, Enabled. To disable the feature, select Disabled. If you are not sure which setting to select, keep the
default, Enabled.
WildCard. This setting enables or disables wildcards for your host. For example, if your DDNS address is
myplace.dyndns.org and you enable wildcards, then x.myplace.dyndns.org will work as well (x is the
wildcard). To enable wildcards, keep the default, Enabled. To disable wildcards, select Disabled. If you are
not sure which setting to select, keep the default, Enabled.
Status. The status of the DDNS service connection is displayed here.
Update. To manually trigger an update, click this button.
Chapter 5: Configuring the Wireless-N Gigabit Router with Storage Link
The Setup Tab - DDNS
17
Wireless-N Gigabit Router with Storage Link
TZO.com
E-mail Address, TZO Password, and Domain Name. Enter the settings of the account you set up with TZO.
Internet IP Address. The Router’s Internet IP address is displayed here. Because it is dynamic, it will change.
Status. The status of the DDNS service connection is displayed here.
Update. To manually trigger an update, click this button.
When you have finished making changes to this screen, click the Save Settings button to save the changes, or
click the Cancel Changes button to undo your changes. For more information, click Help.
Figure 5-10: Setup Tab - TZO.com
Chapter 5: Configuring the Wireless-N Gigabit Router with Storage Link
The Setup Tab - DDNS
18
Wireless-N Gigabit Router with Storage Link
The Setup Tab - MAC Address Clone
A MAC address is a 12-digit code assigned to a unique piece of hardware for identification, like a social security
number. Some ISPs will require you to register a MAC address in order to access the Internet. If you do not wish
to re-register the MAC address with your ISP, you may assign the MAC address you have currently registered with
your ISP to the Router with the MAC Address Clone feature.
MAC Address Clone
To use MAC address cloning, select Enabled. Otherwise, keep the default, Disabled.
MAC Address. Enter the MAC Address registered with your ISP.
Clone My PC’s MAC. If you want to clone the MAC address of the PC you are currently using to configure the
Router, then click this button. The Router will automatically detect your PC’s MAC address, so you do NOT have to
call your ISP to change the registered MAC address to the Router’s MAC address. It is recommended that the PC
registered with the ISP is used to open the MAC Address Clone screen.
When you have finished making changes to this screen, click the Save Settings button to save the changes, or
click the Cancel Changes button to undo your changes. For more information, click Help.
Figure 5-11: Setup Tab - MAC Clone
mac address: the unique address that a
manufacturer assigns to each networking device.
Chapter 5: Configuring the Wireless-N Gigabit Router with Storage Link
The Setup Tab - MAC Address Clone
19
Wireless-N Gigabit Router with Storage Link
The Setup Tab - Advanced Routing
The Advanced Routing screen allows you to configure the dynamic and static routing settings.
Advanced Routing
NAT
If this Router is hosting your network’s connection to the Internet, select
network, select
Disabled
. When the NAT setting is disabled, dynamic routing will be enabled.
Enabled
. If another Router exists on your
Dynamic Routing
This feature enables the Router to automatically adjust to physical changes in the network’s layout and exchange
routing tables with the other router(s). The Router determines the network packets’ route based on the fewest
number of hops between the source and the destination. To use dynamic routing, select
Disabled
. When the NAT setting is disabled, dynamic routing will be enabled.
Enabled
. Otherwise, select
Static Routing
A static route is a pre-determined pathway that network information must travel to reach a specific host or
network. Use this feature to set up a static route between the Router and another network (you can have up to 20
static routes). To create a static route, alter the following settings:
Route Entries. Select the number of the static route from the drop-down menu.
Enter Route Name. Enter a name for the static route, using a maximum of 25 alphanumeric characters.
Destination LAN IP. The Destination LAN IP Address is the address of the remote network or host to which
you want to assign a static route. Enter the IP address of the host for which you wish to create a static route.
Subnet Mask. The Subnet Mask determines which portion of a Destination IP address is the network portion,
and which portion is the host portion.
Figure 5-12: Setup Tab - Advanced Routing
Default Gateway. This is the IP address of the gateway device that allows for contact between the Router and
the remote network or host.
Interface. Select LAN & Wireless or WAN (Internet), depending on the location of the final destination.
Delete This Entry. To delete a route, select its number from the drop-down menu, and click this button.
Chapter 5: Configuring the Wireless-N Gigabit Router with Storage Link
The Setup Tab - Advanced Routing
20
Wireless-N Gigabit Router with Storage Link
Show Routing Table. Click the Show Routing Table button to open a screen displaying how data is routed
through your local network. For each route, the Destination LAN IP address, Subnet Mask, Gateway, and Interface
are displayed. Click the Refresh button to update the information. Click the Close button to exit this screen.
When you have finished making changes to this screen, click the Save Settings button to save the changes, or
click the Cancel Changes button to undo your changes. For more information, click Help.
Figure 5-13: Routing Table
Chapter 5: Configuring the Wireless-N Gigabit Router with Storage Link
The Setup Tab - Advanced Routing
21
Wireless-N Gigabit Router with Storage Link
The Wireless Tab - Basic Wireless Settings
The basic settings for wireless networking are set on this screen.
Basic Wireless Settings
Network Mode. If you have wireless devices in your network, keep the default setting, Mixed. If you do not have
any wireless devices in your network, select Disable.
Network Name (SSID). The SSID is the network name shared among all points in a wireless network. The SSID
must be identical for all devices in the wireless network. It is case-sensitive and must not exceed 32 characters
(use any of the characters on the keyboard). Make sure this setting is the same for all points in your wireless
network. For added security, you should change the default SSID (linksys) to a unique name.
Figure 5-14: Wireless Tab - Basic Wireless Settings
Radio Band. For best performance in a network using Wireless-N, Wireless-G and Wireless-B devices, keep the
default, Wide - 40MHz Channel. For Wireless-G and Wireless-B networking only, select Standard - 20MHz
Channel.
Wide Channel. If you selected Wide - 40MHz Channel for the Radio Band setting, then this setting will be
available for your primary Wireless-N channel. Select any channel from the drop-down menu.
Standard Channel. Select the channel for Wireless-N, Wireless-G, and Wireless-B networking. If you selected
Wide – 40MHz Channel for the Radio Band setting, then the Standard Channel will be a secondary channel for
Wireless-N. If you are not sure which channel to select, keep the default, Auto.
SSID Broadcast. When wireless clients survey the local area for wireless networks to associate with, they will
detect the SSID broadcast by the Router. To broadcast the Router's SSID, keep the default setting, Enabled. If you
do not want to broadcast the Router's SSID, then select Disabled.
When you have finished making changes to this screen, click the Save Settings button to save the changes, or
click the Cancel Changes button to undo your changes. For more information, click Help.
NOTE: If you select Wide - 40MHz Channel for the
Radio Band setting, then Wireless-N can use two
channels: a primary one (Wide Channel) and a
secondary one (Standard Channel). This will
enhance Wireless-N performance.
Chapter 5: Configuring the Wireless-N Gigabit Router with Storage Link
The Wireless Tab - Basic Wireless Settings
22
Wireless-N Gigabit Router with Storage Link
The Wireless Tab - Wireless Security
These settings configure the security of your wireless network. There are six wireless security modes supported
by the Router: PSK-Personal, PSK2-Personal, PSK-Enterprise, PSK2-Enterprise, RADIUS, and WEP. (PSK stands for
Pre-Shared Key, which is stronger than WEP encryption. WEP stands for Wired Equivalent Privacy, while RADIUS
stands for Remote Authentication Dial-In User Service.) For details on configuring wireless security for the Router,
turn to “Appendix B: Wireless Security.” If you do not want to use wireless security, select Disabled.
Wireless Security
Security Mode. Select the mode you want to use: PSK-Personal, PSK2-Personal, PSK-Enterprise, PSK2Enterprise, RADIUS, or WEP. PSK2 is a more advanced, more secure version of PSK.
Follow the instructions for the security method you want to use.
PSK-Personal
Encryption. Select the algorithm you want to use, TKIP or AES. (AES is a stronger encryption method than TKIP.)
Pre-shared Key. Enter the key shared by the Router and your other network devices. It must have
8-63 characters.
Key Renewal. Enter the Key Renewal period, which tells the Router how often it should change encryption keys.
Figure 5-15: Wireless Tab - Wireless Security
(PSK-Personal)
When you have finished making changes to this screen, click the Save Settings button to save the changes, or
click the Cancel Changes button to undo your changes. For more information, click Help.
PSK2-Personal
Encryption. Select the algorithm(s) you want to use, AES or TKIP or AES. (AES is a stronger encryption method
than TKIP.)
Pre-shared Key. Enter the key shared by the Router and your other network devices. It must have
8-63 characters.
Key Renewal. Enter the Key Renewal period, which tells the Router how often it should change encryption keys.
When you have finished making changes to this screen, click the Save Settings button to save the changes, or
click the Cancel Changes button to undo your changes. For more information, click Help.
Chapter 5: Configuring the Wireless-N Gigabit Router with Storage Link
The Wireless Tab - Wireless Security
Figure 5-16: Wireless Security - PSK2-Personal
23
Loading...