Linksys WRT160N User Manual

USER GUIDE

Wireless-N Broadband Router

Model: WRT160N

About This Guide

Icon Descriptions

While reading through the User Guide you may see various icons that call attention to specific items. Below is a description of these icons:

NOTE: This check mark indicates that there is

a note of interest and is something that you should pay special attention to while using the product.

WARNING: This exclamation point indicates

that there is a caution or warning and it is something that could damage your property or product.

About This Guide

WEB: This globe icon indicates a noteworthy

website address or e-mail address.

Online Resources

Website addresses in this document are listed without http:// in front of the address because most current web browsers do not require it. If you use an older web browser, you may have to add http:// in front of the web address.

Resource Website

Linksys www.linksys.com

Linksys International www.linksys.com/international

Glossary www.linksys.com/glossary

Network Security www.linksys.com/security

Copyright and Trademarks

Linksys, Cisco and the Cisco Logo are registered trademarks or trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2009 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders.

Wireless-N Broadband Router

i

Table of Contents

Chapter 1: Product Overview 4

Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Placement Positions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Chapter 2: Wireless Security Checklist 6

General Network Security Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Additional Security Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Chapter 3: Advanced Conguration 7

Setup > Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Setup > DDNS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Setup > MAC Address Clone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Setup > Advanced Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Wireless > Basic Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Wireless > Wireless Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Wireless > Wireless MAC Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Wireless > Advanced Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Security > Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Security > VPN Passthrough. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Access Restrictions > Internet Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Applications and Gaming > Single Port Forwarding. . . . . . . . . . . . . . . . . . . . . . . .20

Applications and Gaming > Port Range Forwarding . . . . . . . . . . . . . . . . . . . . . . .21

Applications & Gaming > Port Range Triggering . . . . . . . . . . . . . . . . . . . . . . . . . .21

Applications and Gaming > DMZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Applications and Gaming > QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Administration > Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Administration > Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Administration > Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Administration > Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Administration > Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Status > Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Status > Local Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Status > Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Wireless-N Broadband Router

Appendix A: Troubleshooting 29

Appendix B: Specications 30

ii

Table of Contents

Appendix C: Warranty Information 31

Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Exclusions and Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Obtaining Warranty Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Appendix D: Regulatory Information 33

FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Safety Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Industry Canada Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Wireless Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Avis de non-responsabilité concernant les appareils sans l . . . . . . . . . . . . . . . . . .34

Declaration of Conformity with Regard to EU Directive 1999/5/EC (R&TTE Directive). . .35

Wireless Equipment (Wireless-N/G/A/B Products) . . . . . . . . . . . . . . . . . . . . . . . . .36

CE Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

National Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Product Usage Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Technical Documents on

www.linksysbycisco.com/international. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste

Electric and Electronic Equipment (WEEE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Appendix E: Software End User License Agreement 42

Cisco Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Software Licenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Wireless-N Broadband Router

iii

Chapter 1

Product Overview

Chapter 1: Product Overview

Thank you for choosing the Linksys Wireless-N Broadband Router. The Router lets you access the Internet via a wireless connection or through one of its four switched ports. You can also use the Router to share resources, such as computers. A variety of security features help to protect your data and your privacy while online. Security features include WPA2 security, a Stateful Packet Inspection (SPI) firewall and NAT technology. Configuring the Router is easy using the provided browser-based utility.

Front Panel

1, 2, 3, 4 (Green/Blue) These numbered LEDs,

corresponding with the numbered ports on the Router’s back panel, serve two purposes. The LED is solidly lit when the Router is connected to a device through that port. It flashes to indicates network activity.

Wi-Fi Protected Setup Button If you have

client devices, such as wireless adapters, that support Wi-Fi Protected Setup, then you can use Wi-Fi Protected Setup to automatically configure wireless security for your wireless network(s).

To use Wi-Fi Protected Setup, run the Setup Wizard, or refer to the “Wireless > Basic Wireless Settings” section of “Chapter 3: Advanced Configuration”.

Wi-Fi Protected Setup LED (Blue/Amber) It

lights up blue when wireless security is enabled. The LED flashes blue for two minutes during Wi-Fi Protected Setup.

The LED lights up amber if there is an error during the Wi-Fi Protected Setup process. Make sure the client device supports Wi-Fi Protected Setup. Wait until the LED is off, and then try again.

The LED flashes amber when a Wi-Fi Protected Setup session is active, and a second session begins. The Router supports one session at a time. Wait until the LED is off before starting the next Wi-Fi Protected Setup session.

Wireless (Blue) The Wireless LED lights up

when the wireless feature is enabled. If the LED is flashing, the Router is actively sending or receiving data over the network.

Internet (Blue) The Internet LED lights up

when there is a connection made through the Internet port. A flashing LED indicates network activity over the Internet port.

Power (Blue) The Power LED lights up and will

stay on while the Router is powered on. When the Router goes through its self-diagnostic mode during every boot-up, this LED will flash. When the diagnostic is complete, the LED will be solidly lit.

Back Panel

Internet This port is where you will connect

your cable or DSL Internet connection.

4, 3, 2, 1 These ports (4, 3, 2, 1) connect the

Router to computers and other Ethernet network devices on your wired network.

Reset There are two ways to reset the Router’s

factory defaults. Either press and hold the Reset Button for approximately five seconds, or restore the defaults from Administration > Factory Defaults in the Router’s web-based utility.

Power The Power port is where you will

connect the power adapter.

Placement Positions

There are two ways to physically install the Router. The first way is to place the Router horizontally on a surface. The second way is to mount the Router on a wall.

Horizontal Placement

The Router has four rubber feet on its bottom panel. Place the Router on a level surface near an electrical outlet.

Wireless-N Broadband Router

4

Chapter 1

Product Overview

Wall-Mounting Placement

The Router has two wall-mount slots on its bottom panel. The distance between the slots is 152 mm (6 inches).

Two screws are needed to mount the Router.

Suggested Mounting Hardware

4-5 mm 1-1.5 mm

†Note: Mounting hardware illustrations are not

true to scale.

NOTE: Linksys is not responsible for damages

incurred by insecure wall-mounting hardware.

2.5-3.0 mm

Follow these instructions:

1. Determine where you want to mount the Router. Make sure that the wall you use is smooth, flat, dry, and sturdy. Also make sure the location is within reach of an electrical outlet.

2. Drill two holes into the wall. Make sure the holes are 152 mm (6 inches) apart.

3. Insert a screw into each hole and leave 3 mm (0.12 inches) of its head exposed.

4. Maneuver the Router so the wall-mount slots line up with the two screws.

5. Place the wall-mount slots over the screws and slide the Router down until the screws fit snugly into the wall-mount slots.

Wireless-N Broadband Router

Print this page at 100% size.

Cut along the dotted line, and place on the wall to drill precise spacing.

Wall Mounting Template

5

Chapter 2

Wireless Security Checklist

Chapter 2: Wireless Security Checklist

Wireless networks are convenient and easy to install, so homes with high-speed Internet access are adopting them at a rapid pace. Because wireless networking operates by sending information over radio waves, it can be more vulnerable to intruders than a traditional wired network. Like signals from your cellular or cordless phones, signals from your wireless network can also be intercepted. Since you cannot physically prevent someone from connecting to your wireless network, you need to take some additional steps to keep your network secure.

1. Change the default wireless network name or SSID

Wireless devices have a default wireless network name or Service Set Identifier (SSID) set by the factory. This is the name of your wireless network, and can be up to 32 characters in length. Linksys wireless products use linksys as the default wireless network name. You should change the wireless network name to something unique to distinguish your wireless network from other wireless networks that may exist around you, but do not use personal information (such as your Social Security number) because this information may be available for anyone to see when browsing for wireless networks.

2. Change the default password

For wireless products such as access points and routers, you will be asked for a password when you want to change their settings. These devices have a default password set by the factory. The Linksys default password is admin. Hackers know these defaults and may try to use them to access your wireless device and change your network settings. To thwart any unauthorized changes, customize the device’s password so it will be hard to guess.

4. Enable encryption

Encryption protects data transmitted over a wireless network. Wi-Fi Protected Access (WPA/WPA2) and Wired Equivalent Privacy (WEP) offer different levels of security for wireless communication.

A network encrypted with WPA/WPA2 is more secure than a network encrypted with WEP, because WPA/WPA2 uses dynamic key encryption. To protect the information as it passes over the airwaves, you should enable the highest level of encryption supported by your network equipment.

WEP is an older encryption standard and may be the only option available on some older devices that do not support WPA.

General Network Security Guidelines

Wireless network security is useless if the underlying network is not secure.

• Password protect all computers on the network and

individually password protect sensitive files.

• Change passwords on a regular basis.

• Install anti-virus software and personal firewall

software.

• Disable file sharing (peer-to-peer). Some applications

may open file sharing without your consent and/or knowledge.

Additional Security Tips

• Keep wireless routers, access points, or gateways away

from exterior walls and windows.

• Turn wireless routers, access points, or gateways

off when they are not being used (at night, during vacations).

• Use strong passphrases that are at least eight characters

in length. Combine letters and numbers to avoid using standard words that can be found in the dictionary.

3. Enable MAC address filtering

Linksys routers give you the ability to enable Media Access Control (MAC) address filtering. The MAC address is a unique series of numbers and letters assigned to every networking device. With MAC address filtering enabled, wireless network access is provided solely for wireless devices with specific MAC addresses. For example, you can specify the MAC address of each computer in your home so that only those computers can access your wireless network.

Wireless-N Broadband Router

WEB: For more information on wireless

security, visit www.linksys.com/security

6

Chapter 3

Chapter 3: Advanced Configuration

After setting up the Router with the Setup Wizard (located on the CD-ROM), the Router will be ready for use. However, if you’d like to change its advanced settings, use the Router’s web-based utility. This chapter describes each web page of the utility and each page’s key functions. You can access the utility via a web browser on a computer connected to the Router.

The web-based utility has these main tabs: Setup, Wireless, Security, Access Restrictions, Applications & Gaming, Administration, and Status. Additional tabs will be available after you click one of the main tabs.

NOTE: When first installing the Router, you

should use the Setup Wizard on the Setup CD-ROM. If you want to configure advanced settings, use this chapter to learn about the web-based utility.

Advanced Configuration

Setup > Basic Setup

How to Access the Web-Based Utility

To access the web-based utility, launch the web browser on your computer, and enter the Router’s default IP address,

192.168.1.1, in the Address field. Then, press Enter.

A login screen will appear. (Non-Windows XP users will see a similar screen.) Leave the User name field blank. The first time you open the Web-based utility, use the default password admin. (You can set a new password from the Administration tab’s Management screen.) Click OK to continue.

Login Screen

Setup > Basic Setup

Internet Setup

The Internet Setup section configures the Router to your Internet connection. Most of this information can be obtained through your ISP.

Internet Connection Type

Select the type of Internet connection your ISP provides from the drop-down menu. These are the available types:

• Automatic Configuration - DHCP

• Static IP

• PPPoE

• PPTP

• L2TP

• Telstra Cable

Automatic Configuration - DHCP

By default, the Router’s Internet Connection Type is set to Automatic Configuration - DHCP, which should be kept only if your ISP supports DHCP or you are connecting through a dynamic IP address. (This option usually applies to cable connections.)

The first screen that appears is the Basic Setup screen. This allows you to change the Router’s general settings.

Wireless-N Broadband Router

Internet Connection Type > Automatic Configuration - DHCP

7

Chapter 3

Advanced Configuration

Static IP

If you are required to use a permanent IP address to connect to the Internet, select Static IP.

Internet Connection Type > Static IP

Internet IP Address This is the Router’s IP address, when

seen from the Internet. Your ISP will provide you with the IP Address you need to specify here.

Subnet Mask This is the Router’s Subnet Mask, as seen

by users on the Internet (including your ISP). Your ISP will provide you with the Subnet Mask.

Default Gateway Your ISP will provide you with the IP

address of the ISP server.

DNS 1-3 Your ISP will provide you with at least one DNS

(Domain Name System) server IP address.

before your Internet connection terminates. The default Max Idle Time is 15 minutes.

Keep Alive: Redial Period If you select this option,

the Router will periodically check your Internet connection. If you are disconnected, then the Router will automatically re-establish your connection. To use this option, select Keep Alive. In the Redial Period field, you specify how often you want the Router to check the Internet connection. The default Redial Period is 30 seconds.

PPTP

Point-to-Point Tunneling Protocol (PPTP) is a service that applies to connections in Europe only.

PPPoE

Some DSL-based ISPs use PPPoE (Point-to-Point Protocol over Ethernet) to establish Internet connections. If you are connected to the Internet through a DSL line, check with your ISP to see if they use PPPoE. If they do, you will have to enable PPPoE.

Internet Connection Type > PPPoE

Username and Password Enter the Username and

Password provided by your ISP.

Service Name If provided by your ISP, enter the Service

Name.

Connect on Demand: Max Idle Time You can configure

the Router to cut the Internet connection after it has been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. To use this option, select Connect on Demand. In the Max Idle Time field, enter the number of minutes you want to have elapsed

Internet Connection Type > PPTP

If your ISP supports DHCP or you are connecting through a dynamic IP address, then select Obtain an IP Address Automatically. If you are required to use a permanent IP address to connect to the Internet, then select Specify an IP Address. Then configure the following:

• Specify an IP Address This is the Router’s IP address,

as seen from the Internet. Your ISP will provide you with the IP Address you need to specify here.

• Subnet Mask This is the Router’s Subnet Mask, as

seen by users on the Internet (including your ISP). Your ISP will provide you with the Subnet Mask.

• Default Gateway Your ISP will provide you with the

IP address of the ISP server.

• DNS 1-3 Your ISP will provide you with at least one

DNS (Domain Name System) server IP address.

PPTP Server IP Address Your ISP will provide you with

the IP address of the PPTP server.

Username and Password Enter the Username and

Password provided by your ISP.

Connect on Demand: Max Idle Time You can configure

the Router to cut the Internet connection after it has been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated due to

Wireless-N Broadband Router

8

Chapter 3

Advanced Configuration

inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. To use this option, select Connect on Demand. In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet connection terminates. The default Max Idle Time is 15 minutes.

Keep Alive: Redial Period

Router will periodically check your Internet connection. If you are disconnected, then the Router will automatically re-establish your connection. To use this option, select Keep Alive. In the Redial Period field, you specify how often you want the Router to check the Internet connection. The default value is 30 seconds.

If you select this option, the

L2TP

L2TP is a service that applies to connections in Israel only.

Internet Connection Type > L2TP

Server IP Address This is the IP address of the L2TP

Server. Your ISP will provide you with the IP Address you need to specify here.

Username and Password Enter the Username and

Password provided by your ISP.

Connect on Demand: Max Idle Time You can configure

the Router to cut the Internet connection after it has been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. To use this option, select Connect on Demand. In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet connection terminates. The default Max Idle Time is 15 minutes.

Telstra Cable

Telstra Cable is a service that applies to connections in Australia only.

Internet Connection Type > Telstra Cable

Server IP Address This is the IP address of the Heartbeat

Server. Your ISP will provide you with the IP Address you need to specify here.

Username and Password Enter the Username and

Password provided by your ISP.

Connect on Demand: Max Idle Time You can configure

the Router to cut the Internet connection after it has been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. To use this option, select Connect on Demand. In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet connection terminates. The default Max Idle Time is 15 minutes.

Keep Alive: Redial Period If you select this option,

the Router will periodically check your Internet connection. If you are disconnected, then the Router will automatically re-establish your connection. To use this option, select Keep Alive. In the Redial Period field, you specify how often you want the Router to check the Internet connection. The default Redial Period is 30 seconds.

Optional Settings

Some of these settings may be required by your ISP. Verify with your ISP before making any changes.

Keep Alive: Redial Period If you select this option,

the Router will periodically check your Internet connection. If you are disconnected, then the Router will automatically re-establish your connection. To use this option, select Keep Alive. In the Redial Period field, you specify how often you want the Router to check the Internet connection. The default Redial Period is

30 seconds.

Wireless-N Broadband Router

Optional Settings

Host Name and Domain Name These fields allow you to

supply a host and domain name for the Router. Some ISPs, usually cable ISPs, require these names as identification. You may have to check with your ISP to see if your broadband Internet service has been configured with a

9

Chapter 3

Advanced Configuration

host and domain name. In most cases, leaving these fields blank will work.

MTU MTU is the Maximum Transmission Unit. It specifies

the largest packet size permitted for Internet transmission. Select Manual if you want to manually enter the largest packet size that is transmitted. To have the Router select the best MTU for your Internet connection, keep the default setting, Auto.

Size When Manual is selected in the MTU field, this option

is enabled. Leave this value in the 1200 to 1500 range. The default size depends on the Internet Connection Type:

• DHCP, Static IP, or Telstra: 1500

• PPPoE: 1492

• PPTP or L2TP: 1460

Network Setup

The Network Setup section changes the settings on the network connected to the Router’s Ethernet ports. Wireless setup is performed through the Wireless tab.

Router IP

This presents both the Router’s IP Address and Subnet Mask as seen by your network.

Router IP

DHCP Server Setting

The settings allow you to configure the Router’s Dynamic Host Configuration Protocol (DHCP) server function. The Router can be used as a DHCP server for your network. A DHCP server automatically assigns an IP address to each computer on your network. If you choose to enable the Router’s DHCP server option, make sure there is no other DHCP server on your network.

DHCP Reservation

You will see a list of DHCP clients with the following information: Client Name, Interface, IP Address, and MAC Address.

DHCP Reservation

• Select Clients from DHCP Table Click the Select

check box to reserve a client’s IP address. Then click Add Clients.

• Manually Adding Client To manually assign an IP

address, enter the client’s name in the Enter Client Name field. Enter the IP address you want it to have in the Assign IP Address field. Enter its MAC address in the To This MAC Address field. Then click Add.

Clients Already Reserved

A list of DHCP clients and their fixed local IP addresses will be displayed at the bottom of the screen. If you want to remove a client from this list, click Remove.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes. To view the most up-to-date information, click Refresh. To exit this screen, click Close.

DHCP Server Setting

DHCP Server DHCP is enabled by factory default. If you

already have a DHCP server on your network, or you don’t want a DHCP server, then select Disabled (no other DHCP features will be available).

DHCP Reservation Click this button if you want to assign

a fixed local IP address to a MAC address.

Wireless-N Broadband Router

Start IP Address Enter a value for the DHCP server to

start with when is default IP address is 192.168.1.1, the Start IP Address must be 192.168.1.2 or greater, but smaller than 192.168.1.253. The default Starting IP Address is 192.168.1.100

Maximum Number of Users Enter the maximum

number of PCs that you want the DHCP server to assign IP addresses to. This number cannot be greater than 253. The default is 50.

IP Address Range Displayed here is the range of available

IP addresses.

Client Lease Time The Client Lease Time is the amount

of time a network user will be allowed connection to the Router with their current dynamic IP address. Enter the

suing IP addresses. Because the Router’s

.

10

Chapter 3

Advanced Configuration

amount of time, in minutes, that the user will be “leased” this dynamic IP address. After the time is up, the user will be automatically assigned a new dynamic IP address. The default is 0 minutes, which means one day.

Static DNS 1-3

the Internet translates domain or website names into Internet addresses or URLs. Your ISP will provide you with at least one DNS Server IP Address. If you wish to use another, enter that IP Address in one of these fields. You can enter up to three DNS Server IP Addresses here. The Router will use these for quicker access to functioning DNS servers

WINS The Windows Internet Naming Service (WINS)

manages each PC’s interaction with the Internet. If you use a WINS server, enter that server’s IP Address here. Otherwise, leave this blank.

The Domain Name System (DNS) is how

.

Time Setting

Time Zone Select the time zone in which your network

functions from this drop-down menu. (You can even automatically adjust for daylight saving time.)

Time Setting

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Setup > DDNS

The Router offers a Dynamic Domain Name System (DDNS) feature. DDNS lets you assign a fixed host and domain name to a dynamic Internet IP address. It is useful when you are hosting your own website, FTP server, or other server behind the Router.

Before you can use this feature, you need to sign up for DDNS service with a DDNS service provider, www.dyndns.org or www.TZO.com. If you do not want to use this feature, keep the default setting, Disabled.

DDNS

DDNS Service

If your DDNS service is provided by DynDNS.org, then select DynDNS.org from the drop-down menu. If your DDNS service is provided by TZO, then select TZO.com. The features available on the DDNS screen will vary, depending on which DDNS service provider you use.

DynDNS.org

Setup > DDNS > DynDNS

Username Enter the Username for your DDNS account.

Password Enter the Password for your DDNS account.

Host Name The is the DDNS URL assigned by the DDNS

service.

System Select the DynDNS service you use: Dynamic,

Static, or Custom. The default selection is Dynamic.

Mail Exchange (Optional) Enter the address of your mail

exchange server, so e-mails to your DynDNS address go to your mail server.

Backup MX This feature allows the mail exchange server

to be a backup. To disable this feature, keep the default, Disabled. To enable the feature, select Enabled. If you are not sure which setting to select, keep the default,

Disabled.

Wildcard This setting enables or disables wildcards

for your host. For example, if your DDNS address is

myplace.dyndns.org and you enable wildcards, then x.myplace.dyndns.org will work as well (x is the wildcard).

To disable wildcards, keep the default, Disabled. To enable wildcards, select Enabled. If you are not sure which setting to select, keep the default, Disabled.

Internet IP Address The Router’s Internet IP address is

displayed here. Because it is dynamic, it will change.

Status The status of the DDNS service connection is

displayed here.

Update To manually trigger an update, click this button.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Wireless-N Broadband Router

11

Chapter 3

Advanced Configuration

TZO.com

Setup > DDNS > TZO

E-mail Address, TZO Key, and Domain Name Enter the

settings of the account you set up with TZO.

Internet IP Address The Router’s Internet IP address is

displayed here. Because it is dynamic, it will change.

Status The status of the DDNS service connection is

displayed here.

Update To manually trigger an update, click this button.

Clone My PC’s MAC Click this button to clone the MAC

address of the computer you are using.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Setup > Advanced Routing

This screen is used to set up the Router’s advanced functions. Operating Mode allows you to select the type(s) of advanced functions you use. Dynamic Routing automatically adjusts how packets travel on your network. Static Routing sets up a fixed route to another network destination.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Setup > MAC Address Clone

A MAC address is a 12-digit code assigned to a unique piece of hardware for identification. Some ISPs will require you to register a MAC address in order to access the Internet. If you do not wish to re-register the MAC address with your ISP, you may assign the MAC address you have currently registered with your ISP to the Router with the MAC Address Clone feature.

Setup > MAC Address Clone

MAC Address Clone

Enabled/Disabled To have the MAC Address cloned,

select Enabled.

MAC Address Enter the MAC Address registered with

your ISP here.

Setup > Advanced Routing

Advanced Routing

NAT

Enabled/Disabled If this Router is hosting your network’s

connection to the Internet, keep the default, Enabled. If another router exists on your network, select Disabled. When the NAT setting is disabled, dynamic routing will be enabled.

Dynamic Routing (RIP)

Enabled/Disabled This feature enables the Router to

automatically adjust to physical changes in the network’s layout and exchange routing tables with the other router(s). The Router determines the network packets’ route based on the fewest number of hops between the source and the destination. When the NAT setting is enabled, the Dynamic Routing feature is automatically disabled. When the NAT setting is disabled, this feature is available. Select Enabled to use the Dynamic Routing feature.

Static Routing

A static route is a pre-determined pathway that network information must travel to reach a specific host or network. Enter the information described below to set up a new static route.

Wireless-N Broadband Router

12

Chapter 3

Advanced Configuration

Route Entries To set up a static route between the Router

and another network, select a number from the dropdown list. Click Delete This Entry to delete a static route.

Enter Route Name Enter a name for the Route here,

using a maximum of 25 alphanumeric characters.

Destination LAN IP The Destination LAN IP is the address

of the remote network or host to which you want to assign a static route.

Subnet Mask The Subnet Mask determines which

portion of a Destination LAN IP address is the network portion, and which portion is the host portion.

Gateway This is the IP address of the gateway device that

allows for contact between the Router and the remote network or host.

Interface This interface tells you whether the Destination

IP Address is on the LAN & Wireless (Ethernet and wireless networks) or the WAN (Internet).

Click Show Routing Table to view the static routes you have already set up.

Wi-Fi Protected Setup. Proceed to the “Wi-Fi Protected Setup” section.

Basic Wireless Settings

Wireless > Basic Wireless Settings (Manual Setup)

Network Mode From this drop-down menu, you can

select the wireless standards running on your network. If you have Wireless-N, Wireless-G, and Wireless-B devices in your network, keep the default setting, Mixed. If you have only Wireless-G and Wireless-B devices in your network, select BG-Mixed. If you have only Wireless-N devices, select Wireless-N Only. If you have only Wireless-G devices, select Wireless-G Only. If you have only Wireless-B devices, select Wireless-B Only. If you do not have any wireless devices in your network, select Disabled.

Advanced Routing > Routing Table

Routing Table

For each route, the Destination LAN IP address, Subnet Mask, Gateway, and Interface are displayed. Click Refresh to update the information. Click Close to exit this screen.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Wireless > Basic Wireless Settings

The basic settings for wireless networking are set on this screen.

There are two ways to configure the Router’s wireless network(s), manual and Wi-Fi Protected Setup.

Wi-Fi Protected Setup is a feature that makes it easy to set up your wireless network. If you have client devices, such as wireless adapters, that support Wi-Fi Protected Setup, then you can use Wi-Fi Protected Setup.

Configuration View To manually configure your wireless

network, select Manual. Proceed to the “Basic Wireless Settings” section. To use Wi-Fi Protected Setup, select

Network Name (SSID) The SSID is the network name

shared among all points in a wireless network. The SSID must be identical for all devices in the wireless network. It is case-sensitive and must not exceed 32 characters (use any of the characters on the keyboard). Make sure this setting is the same for all points in your wireless network. For added security, you should change the default SSID (linksys) to a unique name.

Channel Width Select Auto if you want the Router

to automatically determine the proper channel width (20 MHz or 40 MHz) to use, or select 20 MHz only (default) if you want the Router to operate in Wireless-B and Wireless-G mode only. For best performance, Auto is recommended.

Channel Select a channel from 1 to 11, or Auto (default).

SSID Broadcast When wireless clients survey the local

area for wireless networks to associate with, they will detect the SSID broadcast by the Router. To broadcast the Router’s SSID, keep the default setting, Enabled. If you do not want to broadcast the Router’s SSID, then select Disabled.

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Wireless-N Broadband Router

13

Chapter 3

Advanced Configuration

Wi-Fi Protected Setup

There are three methods available. Use the method that applies to the client device you are configuring.

Wireless > Basic Wireless Settings (Wi-Fi Protected Setup)

NOTE: Wi-Fi Protected Setup configures one

client device at a time. Repeat the instructions for each client device that supports Wi-Fi Protected Setup.

2. After the client device has been configured, click OK. Then refer back to your client device or its documentation for further instructions.

The Wi-Fi Protected Setup Status, Network Name (SSID), Security, Encryption, and Passphrase are displayed at the bottom of the screen.

NOTE: If you have client devices that do not

support Wi-Fi Protected Setup, note the wireless settings, and then manually configure those client devices.

Wireless > Wireless Security

The Wireless Security screen configures the security of your wireless network. There are six wireless security mode options supported by the Router: WPA Personal, WPA Enterprise, WPA2 Personal, WPA2 Enterprise, RADIUS, and WEP. (WPA stands for Wi-Fi Protected Access, which is a security standard stronger than WEP encryption. WEP stands for Wired Equivalent Privacy, while RADIUS stands for Remote Authentication Dial-In User Service.) These six are briefly discussed here. For detailed instructions on configuring wireless security for the Router, refer to “Chapter 2: Wireless Security.”

Wireless Security

Method #1

Use this method if your client device has a Wi-Fi Protected Setup button.

1. Click or press the Wi-Fi Protected Setup button on

the client device.

2. Click the Wi-Fi Protected Setup button on this

screen.

3. After the client device has been configured, click

OK. Then refer back to your client device or its documentation for further instructions.

Method #2

Use this method if your client device has a Wi-Fi Protected Setup PIN number.

1. Enter the PIN number in the field on this screen.

2. Click Register.

3. After the client device has been configured, click

OK. Then refer back to your client device or its documentation for further instructions.

Method #3

Use this method if your client device asks for the Router’s PIN number.

1. Enter the PIN number listed on this screen. (It is also listed on the label on the bottom of the Router.)

Security Mode

Select the security method for your wireless network. If you do not want to use wireless security, keep the default, Disabled.

WPA Personal

NOTE: If you are using WPA, always remember

that each device in your wireless network MUST use the same WPA method and shared key, or else the network will not function properly.

Security Mode > WPA Personal

Passphrase Enter a Passphrase of 8-63 characters.

Wireless-N Broadband Router

14

Chapter 3

Advanced Configuration

Key Renewal Enter a Key Renewal period, which instructs

the Router how often it should change the encryption keys. The default Group Key Renewal period is 3600 seconds.

WPA2 Personal

Security Mode > WPA2 Personal

Encryption WPA2 supports two encryption methods,

TKIP and AES, with dynamic encryption keys. Select the type of algorithm, AES or TKIP or AES. The default is TKIP

or AES.

Passphrase Enter a Passphrase of 8-63 characters.

Key Renewal Enter a Key Renewal period, which instructs

the Router how often it should change the encryption keys. The default Group Key Renewal period is 3600 seconds.

WPA Enterprise

This option features WPA used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.)

WPA2 Enterprise

This option features WPA2 used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.)

Security Mode > WPA2 Enterprise

Encryption WPA2 supports two encryption methods,

TKIP and AES, with dynamic encryption keys. Select the type of algorithm, AES or TKIP or AES. The default is TKIP

or AES.

RADIUS Server Enter the IP Address of the RADIUS

server.

RADIUS Port Enter the port number of the RADIUS

server. The default value is 1812.

Shared Secret Enter the key shared between the Router

and the server.

Key Renewal Enter a Key Renewal period, which instructs

the Router how often it should change the encryption keys. The default Key Renewal period is 3600 seconds.

Security Mode > WPA Enterprise

RADIUS Server Enter the IP Address of the RADIUS

server.

RADIUS Port Enter the port number of the RADIUS

server. The default value is 1812.

Shared Secret Enter the key shared between the Router

and the server.

Key Renewal Enter a Key Renewal period, which instructs

the Router how often it should change the encryption keys. The default Key Renewal period is 3600 seconds.

Wireless-N Broadband Router

RADIUS

This option features WEP used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.)

Security Mode > RADIUS

15

Chapter 3

IMPORTANT: If you are using WEP encryption,

always remember that each device in your wireless network MUST use the same WEP encryption method and encryption key, or else your wireless network will not function properly.

RADIUS Server Enter the IP Address of the RADIUS

server.

RADIUS Port Enter the port number of the RADIUS

server. The default value is 1812.

Shared Secret Enter the key shared between the Router

and the server.

Encryption Select a level of WEP encryption,

40/64 bits (10 hex digits) or 104/128 bits (26 hex digits). The default is 40/64 bits (10 hex digits).

Passphrase Enter a Passphrase to automatically generate

WEP keys. Then click Generate.

Key 1 If you did not enter a Passphrase, enter the WEP

key manually.

Advanced Configuration

WEP

WEP is a basic encryption method, which is not as secure as WPA.

Security Mode > WEP

Encryption Select a level of WEP encryption,

40/64 bits (10 hex digits) or 104/128 bits (26 hex digits). The default is 40/64 bits (10 hex digits).

Passphrase Enter a Passphrase to automatically generate

WEP keys. Then click Generate.

Key 1 If you did not enter a Passphrase, enter the WEP

key manually.

Wireless > Wireless MAC Filter

Wireless MAC Filter

Enabled/Disabled

either permitting or blocking access, select Enabled. If you do not wish to filter users by MAC Address, keep the default setting, Disabled

Access Restriction

Prevent Select this to block wireless access by MAC

Address. This option is selected by default.

Permit Select this to allow wireless access by MAC

Address. This option is not selected by default.

MAC Address Filter List

Wireless Client List Click this to open the Wireless Client

List screen.

To filter wireless users by MAC Address,

.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Wireless > Wireless MAC Filter

Wireless access can be filtered by using the MAC addresses of the wireless devices transmitting within your network’s radius.

Wireless-N Broadband Router

Wireless Client List

16

Chapter 3

Advanced Configuration

Wireless Client List

This screen shows computers and other devices on the wireless network. The list can be sorted by Client Name, Interface, IP Address, MAC Address, and Status.

Select Save to MAC Address Filter List for any device you want to add to the MAC Address Filter List. Then click Add.

To retrieve the most up-to-date information, click

Refresh. To exit this screen and return to the Wireless MAC Filter screen, click Close.

MAC 01-50 Enter the MAC addresses of the devices

whose wireless access you want to block or allow.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Wireless > Advanced Wireless Settings

This Advanced Wireless Settings screen is used to set up the Router’s advanced wireless functions. These settings should only be adjusted by an expert administrator as incorrect settings can reduce wireless performance.

With Shared Key authentication, the sender and recipient use a WEP key for authentication. Select Shared Key to only use Shared Key authentication.

Basic Rate The Basic Rate setting is not actually one rate

of transmission but a series of rates at which the Router can transmit. The Router will advertise its Basic Rate to the other wireless devices in your network, so they know which rates will be used. The Router will also advertise that it will automatically select the best rate for transmission. The default setting is Default, when the Router can transmit at all standard wireless rates (1-2Mbps, 5.5Mbps, 11Mbps, 18Mbps, and 24Mbps). Other options are 1-2Mbps, for use with older wireless technology, and All, when the Router can transmit at all wireless rates. The Basic Rate is not the actual rate of data transmission. If you want to specify the Router’s rate of data transmission, configure the Transmission Rate setting.

Transmission Rate The rate of data transmission should

be set depending on the speed of your wireless network. You can select from a range of transmission speeds, or you can select Auto to have the Router automatically use the fastest possible data rate and enable the Auto-Fallback feature. Auto-Fallback will negotiate the best possible connection speed between the Router and a wireless client. The default is Auto.

Wireless > Advanced Wireless Settings

Advanced Wireless

AP Isolation This isolates all wireless clients and wireless

devices on your network from each other. Wireless devices will be able to communicate with the Router but not with each other. To use this function, select Enabled. AP Isolation is disabled by default.

Frame Burst Enabling this option should provide your

network with greater performance, depending on the manufacturer of your wireless products. To use this option, keep the default, Enabled. Otherwise, select Disabled.

Authentication Type The default is set to Auto, which

allows either Open System or Shared Key authentication to be used. With Open System authentication, the sender and the recipient do NOT use a WEP key for authentication.

N Transmission Rate The rate of data transmission

should be set depending on the speed of your Wireless-N networking. You can select from a range of transmission speeds, or you can select Auto to have the Router automatically use the fastest possible data rate and enable the Auto-Fallback feature. Auto-Fallback will negotiate the best possible connection speed between the Router and a wireless client. The default is Auto.

CTS Protection Mode The Router will automatically

use CTS (Clear-To-Send) Protection Mode when your Wireless-N and Wireless-G products are experiencing severe problems and are not able to transmit to the Router in an environment with heavy 802.11b traffic. This function boosts the Router’s ability to catch all WirelessN and Wireless-G transmissions but will severely decrease performance. The default is Auto.

Beacon Interval Enter a value between 1 and 65,535

milliseconds. The Beacon Interval value indicates the frequency interval of the beacon. A beacon is a packet broadcast by the Router to synchronize the wireless network. The default value is 100.

DTIM Interval This value, between 1 and 255, indicates

the interval of the Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages. When the Router has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. Its clients

Wireless-N Broadband Router

17

Chapter 3

Advanced Configuration

hear the beacons and awaken to receive the broadcast and multicast messages. The default value is 1.

Fragmentation Threshold This value specifies the

maximum size for a packet before data is fragmented into multiple packets. If you experience a high packet error rate, you may slightly increase the Fragmentation Threshold. Setting the Fragmentation Threshold too low may result in poor network performance. Only minor reduction of the default value is recommended. In most cases, it should remain at its default value of 2346.

RTS Threshold Should you encounter inconsistent data

flow, only minor reduction of the default value, 2347, is recommended. If a network packet is smaller than the preset RTS threshold size, the RTS/CTS mechanism will not be enabled. The Router sends Request to Send (RTS) frames to a particular receiving station and negotiates the sending of a data frame. After receiving an RTS, the wireless station responds with a Clear to Send (CTS) frame to acknowledge the right to begin transmission. The RTS Threshold value should remain at its default value of

2347.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Security > Firewall

The Firewall screen is used to configure a firewall that can filter out various types of unwanted traffic on the Router’s local network.

Deselect the feature to allow anonymous Internet requests

Filter Multicast Multicasting allows for multiple

transmissions to specific recipients at the same time. If multicasting is permitted, then the Router will allow IP multicast packets to be forwarded to the appropriate computers. Select this feature to filter multicasting. This feature is not selected by default.

Filter Internet NAT Redirection This feature uses port

forwarding to block access to local servers from local networked computers. Select this feature to filter Internet NAT redirection. It is not selected by default.

Filter IDENT (Port 113) This feature keeps port 113 from

being scanned by devices outside of your local network. This feature is selected by default. Deselect this feature to disable it.

.

Web Filter

Proxy Use of WAN proxy servers may compromise the

Gateway’s security. Denying Proxy will disable access to any WAN proxy servers. Select this feature to enable proxy filtering. Deselect the feature to allow proxy access

Java Java is a programming language for websites. If you

deny Java, you run the risk of not having access to Internet sites created using this programming language. Select this feature to enable Java filtering. Deselect the feature to allow Java usage

ActiveX ActiveX is a programming language for websites.

If you deny ActiveX, you run the risk of not having access to Internet sites created using this programming language. Select this feature to enable ActiveX filtering. Deselect the feature to allow ActiveX usage

.

Security > Firewall

Firewall

SPI Firewall Protection To use firewall protection,

keep the default selection, Enabled. To turn off firewall protection, select Disabled.

Internet Filter

Filter Anonymous Internet Requests This feature

makes it more difficult for outside users to work their way into your network. This feature is selected by default.

Wireless-N Broadband Router

Cookies A cookie is data stored on your computer and

used by Internet sites when you interact with them. Select this feature to filter cookies. Deselect the feature to allow cookie usage

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

.

Security > VPN Passthrough

The VPN Passthrough screen allows you to enable VPN tunnels using IPSec, PPTP, or L2TP protocols to pass through the Router’s firewall.

18

Chapter 3

Security > VPN Passthrough

VPN Passthrough

IPSec Passthrough Internet Protocol Security (IPSec) is

a suite of protocols used to implement secure exchange of packets at the IP layer. To allow IPSec tunnels to pass through the Router, keep the default, Enabled.

PPTP Passthrough Point-to-Point Tunneling Protocol

(PPTP) allows the Point-to-Point Protocol (PPP) to be tunneled through an IP network. To allow PPTP tunnels to pass through the Router, keep the default, Enabled.

Advanced Configuration

L2TP Passthrough Layer 2 Tunneling Protocol is the

method used to enable Point-to-Point sessions via the Internet on the Layer 2 level. To allow L2TP tunnels to pass through the Router, keep the default, Enabled.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Access Restrictions > Internet Access

The Internet Access screen allows you to block or allow specific kinds of Internet usage and traffic, such as Internet access, designated services, and websites during specific days and times.

Access Restrictions > Internet Access

Internet Access Policy

Access Policy Access can be managed by a policy. Use the

settings on this screen to establish an access policy (after Save Settings is clicked). Selecting a policy from the dropdown menu will display that policy’s settings. To delete a policy, select that policy’s number and click Delete This Policy. To view all the policies, click Summary.

Summary

The policies are listed with the following information: No., Policy Name, Access, Days, Time, and status (Enabled). To enable a policy, select Enabled. To delete a policy, click

Delete. Click Save Settings to save your changes, or click Cancel Changes to cancel your changes. To return to the Internet Access Policy screen, click Close.

Wireless-N Broadband Router

Summary

19

Chapter 3

Advanced Configuration

Status Policies are disabled by default. To enable a policy,

select the policy number from the drop-down menu, and select Enabled.

To create a policy, follow steps 1-11. Repeat these steps to create additional policies, one at a time.

1. Select a number from the Access Policy drop-down menu.

2. Enter a Policy Name in the field provided.

3. To enable this policy, select Enabled.

4. Click Edit List to select which PCs will be affected by the policy. The List of PCs screen appears. You can select a PC by MAC address or IP address. You can also enter a range of IP addresses if you want this policy to affect a group of PCs. After making your changes, click

Save Settings to apply your changes, or click Cancel Changes to cancel your changes. Then click Close.

10. If the application you want to block is not listed or you want to edit a service’s settings, enter the application’s name in the Application Name field. Enter its range in the Port Range fields. Select its protocol from the Protocol drop-down menu. Then click Add.

To modify a service, select it from the Application list. Change its name, port range, and/or protocol setting. Then click Modify.

To delete a service, select it from the Application list. Then click Delete.

11. Click Save Settings to save the policy’s settings. To cancel the policy’s settings, click Cancel Changes.

Applications and Gaming > Single Port Forwarding

The Single Port Forwarding screen allows you to customize port services for common applications on this screen.

When users send these types of requests to your network via the Internet, the Router will forward those requests to the appropriate servers (computers). Before using forwarding, you should assign static IP addresses to the designated servers (use the DHCP Reservation feature on the Basic Setup screen).

List of PCs

5. Select the appropriate option, Deny or Allow,

depending on whether you want to block or allow Internet access for the PCs you listed on the List of PCs screen.

6. Decide which days and what times you want this policy to be enforced. Select the individual days during which the policy will be in effect, or select Everyday. Then enter a range of hours and minutes during which the policy will be in effect, or select 24 Hours.

7. You can block websites with specific URL addresses. Enter each URL in a separate URL field.

8. You can also block websites using specific keywords. Enter each keyword in a separate Keyword field.

9. You can filter access to various services accessed over the Internet, such as FTP or telnet. (You can block up to three applications per policy.)

From the Applications list, select the application you want to block. Then click the >> button to move it to the Blocked List. To remove an application from the Blocked List, select it and click the << button.

Applications and Gaming > Single Port Forwarding

Single Port Forwarding

Common applications are available for the first five entries. Select the appropriate application. Then enter the IP address of the server that should receive these requests. Select Enabled to activate this entry.

For additional applications, complete the following fields:

Application Name Enter the name you wish to give the

application. Each name can be up to 12 characters.

Wireless-N Broadband Router

20

Chapter 3

Advanced Configuration

External Port Enter the external port number used by

the server or Internet application. Check with the Internet application documentation for more information.

Internal Port Enter the internal port number used by

the server or Internet application. Check with the Internet application documentation for more information.

Protocol Select the protocol used for this application,

either TCP or UDP, or Both.

To IP Address For each application, enter the IP address

of the PC that should receive the requests. If you assigned a static IP address to the PC, then you can click DHCP Reservation on the Basic Setup screen to look up its static IP address.

Enabled For each application, select Enabled to enable

port forwarding.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Applications and Gaming > Port Range Forwarding

The Port Range Forwarding screen allows you to set up public services on your network, such as web servers, ftp servers, e-mail servers, or other specialized Internet applications. (Specialized Internet applications are any applications that use Internet access to perform functions such as videoconferencing or online gaming. Some Internet applications may not require any forwarding.)

When users send these types of requests to your network via the Internet, the Router will forward those requests to the appropriate servers (computers). Before using forwarding, you should assign static IP addresses to the designated servers (use the DHCP Reservation feature on the Basic Setup screen).

Port Range Forwarding

To forward a port, enter the information on each line for the criteria required.

Application Name In this field, enter the name you

wish to give the application. Each name can be up to 12 characters.

Start~End Port Enter the number or range of port(s)

used by the server or Internet applications. Check with the Internet application documentation for more information.

Protocol Select the protocol used for this application,

either TCP or UDP, or Both.

To IP Address For each application, enter the IP address

of the PC running the specific application. If you assigned a static IP address to the PC, then you can click DHCP Reservation on the Basic Setup screen to look up its static IP address.

Enabled Select Enabled to enable port forwarding for

the applications you have defined.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Applications & Gaming > Port Range Triggering

The Port Range Triggering screen allows the Router to watch outgoing data for specific port numbers. The IP address of the computer that sends the matching data is remembered by the Router, so that when the requested data returns through the Router, the data is pulled back to the proper computer by way of IP address and port mapping rules.

If you need to forward all ports to one computer, click the DMZ tab.

Applications and Gaming > Port Range Forwarding

Wireless-N Broadband Router

Applications and Gaming > Port Range Triggering

Port Range Triggering

Application Name Enter the application name of the

trigger.

21

Chapter 3

Advanced Configuration

Triggered Range For each application, enter the starting

and ending port numbers of the triggered port number range. Check with the Internet application documentation for the port number(s) needed.

Forwarded Range For each application, enter the starting

and ending port numbers of the forwarded port number range. Check with the Internet application documentation for the port number(s) needed.

Enabled Select Enabled to enable port triggering for the

applications you have defined.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Applications and Gaming > DMZ

The DMZ feature allows one network computer to be exposed to the Internet for use of a special-purpose service such as Internet gaming or videoconferencing. DMZ hosting forwards all the ports at the same time to one PC. The Port Range Forwarding feature is more secure because it only opens the ports you want to have opened, while DMZ hosting opens all the ports of one computer, exposing the computer to the Internet.

address in the field provided. To retrieve this information, click DHCP Client Table.

DMZ > DHCP Client Table

DHCP Client Table

The DHCP Client Table lists computers and other devices that have been assigned IP addresses by the Router. The list can be sorted by Client Name, Interface, IP Address, MAC Address, and Expired Time (how much time is left for the current IP address). To select a DHCP client, click Select. To retrieve the most up-to-date information, click Refresh. To exit this screen and return to the DMZ screen, click Close.

Applications and Gaming > DMZ

DMZ

Any PC whose port is being forwarded must have its DHCP client function disabled and should have a new static IP address assigned to it because its IP address may change when using the DHCP function.

Enabled/Disabled To disable DMZ hosting, select

Disabled. To expose one PC, select Enabled. Then

configure the following settings:

Source IP Address If you want any IP address to be the

source, select Any IP Address. If you want to specify an IP address or range of IP addresses as the designated source, select and complete the IP address range fields.

Destination If you want to specify the DMZ host by IP

address, select IP Address and enter the IP address in the field provided. If you want to specify the DMZ host by MAC address, select MAC Address and enter the MAC

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Applications and Gaming > QoS

Quality of Service (QoS) ensures better service to high-priority types of network traffic, which may involve demanding, real-time applications, such as videoconferencing.

Applications and Gaming > QoS

QoS (Quality of Service)

Wireless

You can configure the support and No Acknowledgement settings in this section.

Wireless-N Broadband Router

22

Chapter 3

Advanced Configuration

WMM Support If you have other devices that support Wi-

Fi Multimedia (WMM) on your network, keep the default,

Enabled. Otherwise, select Disabled.

No Acknowledgement If you want to disable the Router’s

Acknowledgement feature, so the Router will not re-send data if an error occurs, then select Enabled. Otherwise, keep the default, Disabled.

Internet Access Priority

In this section, you can set the bandwidth priority for a variety of applications and devices. There are four levels priority: High, Medium, Normal, or Low. When you set priority, do not set all applications to High, because this will defeat the purpose of allocating the available bandwidth. If you want to select below normal bandwidth, select Low. Depending on the application, a few attempts may be needed to set the appropriate bandwidth priority.

Enabled/Disabled To use the QoS policies you have set,

keep the default, Enabled. Otherwise, select Disabled.

Administration > Management

This lists the QoS entries you have created for your applications and devices.

Priority This column displays the bandwidth priority of

High, Medium, Normal, or Low.

Name This column displays the application, device, or

port name.

Information This column displays the port range or

MAC address entered for your entry. If a pre-configured application or game was selected, there will be no valid entry shown in this section.

Remove Click this button to remove an entry.

Edit Click this button to make changes.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Administration > Management

The Administration > Management screen allows the network’s administrator to manage specific Router functions for access and security.

Management

Router Access

To ensure the Router’s security, you will be asked for your password when you access the Router’s web-based utility. The default is admin.

Router Password Enter a new password for the Router.

Re-enter to confirm Enter the password again to

confirm.

Web Access

Web Utility Access HTTP (HyperText Transport Protocol)

is the communications protocol used to connect to servers on the World Wide Web. HTTPS uses SSL (Secured Socket Layer) to encrypt data transmitted for higher security. Select HTTP or HTTPS. HTTP is the default.

Web Utility Access via Wireless If you are using the

Router in a public domain where you are giving wireless access to your guests, you can disable wireless access to the Router’s web-based utility. You will only be able to access the utility via a wired connection if you disable the setting. Keep the default, Enabled, to allow wireless access to the utility, or select Disabled to block wireless access to the utility.

Wireless-N Broadband Router

Remote Access

Remote Management To permit remote access of the

Router, from outside the local network, select Enabled. Otherwise, keep the default, Disabled.

Web Utility Access HTTP (HyperText Transport Protocol)

is the communications protocol used to connect to servers on the World Wide Web. HTTPS uses SSL (Secured Socket Layer) to encrypt data transmitted for higher security. Select HTTP or HTTPS. HTTP is the default.

24

Chapter 3

Advanced Configuration

Remote Upgrade If you want to be able to upgrade the

Router remotely, from outside the local network, select Enabled. (You must have the Remote Management feature enabled as well.) Otherwise, keep the default,

Disabled.

Allowed Remote IP Address If you want to be able to

access the Router from any external IP address, select Any IP Address. If you want to specify an external IP address or

range of IP addresses, then select the second option and complete the fields provided.

Remote Management Port Enter the port number that

will be open to outside access.

NOTE: When you are in a remote location

and wish to manage the Router, enter

http://<Internet_IP_address>:port or ht tp s:/ /<I nte rn et_ IP_ add re ss> :po rt ,

depending on whether you use HTTP or HTTPS. Enter the Router’s specific Internet IP address in place of <Internet_IP_address>, and enter the Remote Management Port number in place of the word port.

UPnP

Administration > Log

The Router can keep logs of all traffic for your Internet connection.

Administration > Log

Log

Log To disable the Log function, select Disabled. To

monitor traffic between the network and the Internet, keep the default, Enabled. With logging enabled, you can choose to view temporary logs.

View Log To view the logs, click View Log.

Universal Plug and Play (UPnP) allows Windows Me and XP to automatically configure the Router for various Internet applications, such as gaming and videoconferencing.

UPnP If you want to use UPnP, keep the default setting,

Enabled. Otherwise, select Disabled.

Allow Users to Configure Keep the default, Enabled,

if you want to be able to make manual changes to the Router while using the UPnP feature. Otherwise, select

Disabled.

Allow Users to Disable Internet Access Select Enabled,

if you want to be able to prohibit any and all Internet connections. Otherwise, keep the default setting, Disabled.

Backup and Restore

Backup Configurations To back up the Router’s

configuration settings, click this button and follow the onscreen instructions.

Restore Configurations To restore the Router’s

configuration settings, click this button and follow the onscreen instructions. (You must have previously backed up the Router’s configuration settings.)

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Administration > Log > View Log

Log

• Type Select Incoming Log, Outgoing Log, Security

Log, or DHCP Client Log.

• <Type> Log The Incoming Log will display a

temporary log of the source IP addresses and destination port numbers for the incoming Internet traffic. The Outgoing Log will display a temporary log of the local IP addresses, destination URLs/IP addresses, and service/port numbers for the outgoing Internet traffic. The Security log will display the login information for the web-based utility. The DHCP Client Log will display the LAN DHCP server status information.

Click Save the Log to save this information to a file on your PC’s hard drive. Click Refresh to update the log. Click Clear to clear all the information that is displayed.

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Wireless-N Broadband Router

25

Chapter 3

Advanced Configuration

Administration > Diagnostics

The diagnostic tests (Ping and Traceroute) allow you to check the connections of your network devices, including connection to the Internet. This screen also allows you to reset the router.

Administration > Diagnostics

Reboot

Reboot Click Reboot to reset the router.

Traceroute Test

The Traceroute test tests the performance of a connection.

IP or URL Address Enter the address of the PC whose

connection you wish to test.

Start to Traceroute To run the test, click this button. The

Traceroute Test screen will show if the test was successful. Click Close to return to the Diagnostics screen.

Diagnostics > Traceroute

Diagnostics

Ping Test

The Ping test checks the status of a connection.

IP or URL Address Enter the address of the PC whose

connection you wish to test.

Packet Size Enter the packet size you want to use. The

default is 32 bytes.

Times to Ping Enter many times you wish to test it.

Start to Ping To run the test, click this button. The Ping

Test screen will show if the test was successful. Click Close to return to the Diagnostics screen.

Administration > Factory Defaults

The Administration > Factory Defaults screen allows you to restore the Router’s configuration to its factory default settings.

Administration > Factory Defaults

NOTE: Do not restore the factory defaults unless

you are having difficulties with the Router and have exhausted all other troubleshooting measures. Once the Router is reset, you will have to re-enter all of your configuration settings.

Factory Defaults

Diagnostics > Ping

Wireless-N Broadband Router

Restore All Settings To reset the Router’s settings to the

default values, click this button and then follow the onscreen instructions. Any settings you have saved will be lost when the default settings are restored.

26

Chapter 3

Administration > Firmware Upgrade

The Firmware Upgrade screen allows you to upgrade the Router’s firmware. Do not upgrade the firmware unless you are experiencing problems with the Router or the new firmware has a feature you want to use.

Administration > Firmware Upgrade

Advanced Configuration

Status > Router

NOTE: The Router may lose the settings you

have customized. Before you upgrade its firmware, write down all of your custom settings. After you upgrade its firmware, you will have to re-enter all of your configuration settings.

Firmware Upgrade

Before upgrading the firmware, download the Router’s firmware upgrade file from the Linksys website,

www.linksys.com. Then extract the file.

Please select a file to upgrade the firmware Click

Browse and select the extracted firmware upgrade file.

Start to Upgrade After you have selected the

appropriate file, click this button, and f instructions.

ollow the on-screen

Status > Router

The Router screen displays information about the Router and its current settings.

Router Information

Firmware Version This is the version number of the

Router’s current firmware.

Firmware Verification This shows the MD5 value

generated during code compilation.

Current Time This shows the time set on the Router.

Internet MAC Address This is the Router’s MAC Address,

as seen by your ISP.

Host Name If required by your ISP, this was entered on

the Basic Setup screen.

Domain Name If required by your ISP, this was entered

on the Basic Setup screen.

Internet Connection

This section shows the current network information stored in the Router. The information varies depending on the Internet connection type selected on the Basic Setup screen.

Click Refresh to update the on-screen information.

Status > Local Network

Wireless-N Broadband Router

The Local Network screen displays information about the local, wired network.

27

Chapter 3

Status > Local Network

Local Network

Local MAC Address The MAC address of the Router’s

local, wired interface is displayed here.

Advanced Configuration

date information, click Refresh. To exit this screen and return to the Local Network screen, click Close.

Status > Wireless Network

The Wireless Network screen displays information about your wireless network.

Router IP Address This shows the Router’s IP address, as

it appears on your local network.

Subnet Mask This shows the Subnet Mask of the Router.

DHCP Server

DHCP Server The status of the Router’s DHCP server

function is displayed here.

Start IP Address For the range of IP addresses used by

devices on your local network, the starting IP address is shown here.

End IP Address For the range of IP addresses used by

devices on your local network, the ending IP address is shown here.

DHCP Clients Table Click this button to view a list of PCs

that are using the Router as a DHCP server.

Status > Wireless

Wireless Network

MAC Address The MAC address of the Router’s local,

wireless interface is displayed here.

Mode Displayed here is the wireless mode used by the

network.

Network Name (SSID) Displayed here is the name of the

wireless network, which is also called the SSID.

Channel Width Shown here is the Radio Band setting

selected on the Basic Wireless Settings screen.

Channel Shown here is the Channel setting selected on

the Basic Wireless Settings screen.

Security Displayed here is the wireless security method

used by the Router.

SSID Broadcast Displayed here is the status of the SSID

Broadcast feature.

DHCP Clients Table

DHCP Client Table

The DHCP Client Table lists computers and other devices that have been assigned IP addresses by the Router. The list can be sorted by Client Name, Interface, IP Address, MAC Address, and Expired Time (how much time is left for the current IP address). To remove a DHCP client, click Delete. To retrieve the most up-to-

Wireless-N Broadband Router

28

Appendix A

Troubleshooting

Appendix A: Troubleshooting

Your computer cannot connect to the Internet.

Follow these instructions until your computer can connect to the Internet:

• Make sure that the Router is powered on. The Power

LED should be green and not flashing.

• If the Power LED is flashing, then power off all of

your network devices, including the modem, Router, and computers. Then power on each device in the following order:

1. Cable or DSL modem

2. Router

3. Computer

• Check the cable connections. The computer should

be connected to one of the ports numbered 1-4 on the Router, and the modem must be connected to the Internet port on the Router.

The modem does not have an Ethernet port.

The modem is a dial-up modem for traditional dial-up service. To use the Router, you need a cable/DSL modem and high-speed Internet connection.

You cannot use the DSL service to connect manually to the Internet.

After you have installed the Router, it will automatically connect to your Internet Service Provider (ISP), so you no longer need to connect manually.

When you double-click the web browser, you are prompted for a username and password. If you want to get rid of the prompt, follow these instructions.

Launch the web browser and perform the following steps (these steps are specific to Internet Explorer but are similar for other browsers):

1. Select Tools > Internet Options.

2. Click the Connections tab.

3. Select Never dial a connection.

4. Click OK.

The Router does not have a coaxial port for the cable connection.

The Router does not replace your modem. You still need your cable modem in order to use the Router. Connect your cable connection to the cable modem, and then insert the setup CD into your computer. Click Setup and follow the on-screen instructions.

The computer cannot connect wirelessly to the network.

Make sure the wireless network name or SSID is the same on both the computer and the Router. If you have enabled wireless security, then make sure the same security method and key are used by both the computer and the Router.

You need to modify the settings on the Router.

Open the web browser (for example, Internet Explorer or Firefox), and enter the Router’s IP address in the address field (the default IP address is 192.168.1.1). When prompted, enter the password to the Router (the default is admin). Click the appropriate tab to change the settings.

The DSL telephone line does not t into the Router’s Internet port.

The Router does not replace your modem. You still need your DSL modem in order to use the Router. Connect the telephone line to the DSL modem, and then insert the setup CD into your computer. Click Setup and follow the on-screen instructions.

Wireless-N Broadband Router

WEB: If your questions are not addressed here,

refer to the Linksys website, www.linksys.com

29

Appendix B

Appendix B: Specifications

Model WRT160N Standards Draft 802.11n, 802.11g, 802.11b,

802.3, 802.3u

Ports Power, Internet, and Ethernet (1-4) Buttons Reset, Wi-Fi Protected Setup LEDs Ethernet (1-4), Wi-Fi Protected

Setup, Wireless, Internet, Power Cabling Type CAT 5e RF Pwr (EIRP) in dBm 17 dBm Antenna Gain in dBi 1.5 dBi UPnP able/cert Able Security Features WEP, WPA, WPA2 Security Key Bits 128-Bit,

Specifications

Environmental

Dimensions 7.95" x 6.3" x 1.34" (202 x 160 x 34 mm)

Weight 10.4 oz (0.29 kg) Power 12V, 0.5A Certication FCC, CE, IC-03, Wi-Fi Operating Temp. 0 to 40°C (32 to 104°F) Storage Temp. -20 to 60°C (-4 to 140°F) Operating Humidity 10 to 85% Noncondensing Storage Humidity 5 to 90% Noncondensing

Wireless-N Broadband Router

30

Appendix C

Warranty Information

Appendix C: Warranty Information

Limited Warranty

Linksys warrants that this Linksys hardware product will be substantially free of defects in materials and workmanship arising under normal use during the Warranty Period, which begins on the date of purchase by the original enduser purchaser and lasts for the period specified below:

• Two (2) years for new product

• Ninety (90) days for refurbished product

This limited warranty is non-transferable and extends only to the original end-user purchaser. Your exclusive remedy and Linksys’ entire liability under this limited warranty will be for Linksys, at its option, to (a) repair the product with new or refurbished parts, (b) replace the product with a reasonably available equivalent new or refurbished Linksys product, or (c) refund the purchase price of the product less any rebates. Any repaired or replacement products will be warranted for the remainder of the original Warranty Period or thirty (30) days, whichever is longer. All products and/or parts that are replaced become the property of Linksys.

This limited warranty shall apply in addition to any statutory or other rights which you may have under a contract of sale.

Exclusions and Limitations

This limited warranty does not apply if: (a) the product assembly seal has been removed or damaged, (b) the product has been altered or modified, except by Linksys, (c) the product damage was caused by use with nonLinksys products, (d) the product has not been installed, operated, repaired, or maintained in accordance with instructions supplied by Linksys, (e) the product has been subjected to abnormal physical or electrical stress, misuse, negligence, or accident, (f ) the serial number on the Product has been altered, defaced, or removed, or (g) the product is supplied or licensed for beta, evaluation, testing or demonstration purposes for which Linksys does not charge a purchase price or license fee.

ALL SOFTWARE PROVIDED BY LINKSYS WITH THE PRODUCT, WHETHER FACTORY LOADED ON THE PRODUCT OR CONTAINED ON MEDIA ACCOMPANYING THE PRODUCT, IS PROVIDED “AS IS” WITHOUT ANY WARRANTY OF ANY KIND. Without limiting the foregoing, Linksys does not warrant that the operation of the product or software will be uninterrupted or error free. Also, due to the continual development of new techniques for intruding upon and attacking networks, Linksys does not warrant that the product, service, software or any equipment, system or

network on which the product or software is used will be free of vulnerability to intrusion or attack. The product may include or be bundled with third party software or service offerings. This limited warranty shall not apply to such third party software or service offerings. This limited warranty does not guarantee any continued availability of a third party’s service for which this product’s use or operation may require.

TO THE EXTENT NOT PROHIBITED BY LAW, ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY, SATISFACTORY QUALITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THE WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary by jurisdiction.

TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT (INCLUDING ANY SOFTWARE), EVEN IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even if any warranty or remedy provided under this limited warranty fails of its essential purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

Obtaining Warranty Service

If you have a question about your product or experience a problem with it, please go to www.linksys.com/support where you will find a variety of online support tools and information to assist you with your product. If the product proves defective during the Warranty Period, contact Linksys Technical Support for instructions on how to obtain warranty service. The telephone number for Linksys Technical Support in your area can be found in the product User Guide and at www.linksys.com. Have your product serial number and proof of purchase on hand when calling. A DATED PROOF OF ORIGINAL PURCHASE IS REQUIRED TO PROCESS WARRANTY CLAIMS. If you are requested to return your product, you will be given a Return Materials Authorization (RMA) number. You are responsible for properly packaging and shipping your product to Linksys at your cost and risk. You must include the RMA number

Wireless-N Broadband Router

31

Appendix C

and a copy of your dated proof of original purchase when returning your product. Products received without a RMA number and dated proof of original purchase will be rejected. Do not include any other items with the product you are returning to Linksys. Defective product covered by this limited warranty will be repaired or replaced and returned to you without charge. Customers outside of the United States of America and Canada are responsible for all shipping and handling charges, custom duties, VAT and other associated taxes and charges. Repairs or replacements not covered under this limited warranty will be subject to charge at Linksys’ then-current rates.

Technical Support

This limited warranty is neither a service nor a support contract. Information about Linksys’ current technical support offerings and policies (including any fees for support services) can be found at

www.linksys.com/support

Warranty Information

General

This limited warranty is governed by the laws of the jurisdiction in which the Product was purchased by you.

If any portion of this limited warranty is found to be void or unenforceable, its remaining provisions shall remain in full force and effect.

Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623.

For more information, please contact us

www.linksys.com

Select your country, and then select SUPPORT/ TECHNICAL

For product returns:

Select your Country and then select CUSTOMER SUPPORT

Wireless-N Broadband Router

32

Appendix D

Regulatory Information

Appendix D: Regulatory Information

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Safety Notices

WARNING: Do not use this product near water,

for example, in a wet basement or near a swimming pool.

WARNING: Avoid using this product during an

electrical storm. There may be a remote risk of electric shock from lightning.

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment or

devices

• Connect the equipment to an outlet other than the

receiver’s

• Consult a dealer or an experienced radio/TV technician

for assistance

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.

Wireless-N Broadband Router

33

Appendix D

Regulatory Information

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003 and RSS210.

Operation is subject to the following two conditions:

1. This device may not cause interference and

2. This device must accept any interference, including interference that may cause undesired operation of the device.

Industry Canada Radiation Exposure Statement

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Avis d’Industrie Canada

Cet appareil numérique de la classe B est conforme aux normes NMB-003 et RSS210 du Canada.

L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes :

1. il ne doit pas produire de brouillage et

2. il doit accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.

Wireless Disclaimer

The maximum performance for wireless is derived from IEEE Standard 802.11 specifications. Actual performance can vary, including lower wireless network capacity, data throughput rate, range and coverage. Performance depends on many factors, conditions and variables, including distance from the access point, volume of network traffic, building materials and construction, operating system used, mix of wireless products used, interference and other adverse conditions.

Avis de non-responsabilité concernant les appareils sans fil

Les performances maximales pour les réseaux sans fil sont tirées des spécifications de la norme IEEE 802.11. Les performances réelles peuvent varier, notamment en fonction de la capacité du réseau sans fil, du débit de la transmission de données, de la portée et de la couverture. Les performances dépendent de facteurs, conditions et variables multiples, en particulier de la distance par rapport au point d’accès, du volume du trafic réseau, des matériaux utilisés dans le bâtiment et du type de construction, du système d’exploitation et de la combinaison de produits sans fil utilisés, des interférences et de toute autre condition défavorable.

Avis d’Industrie Canada concernant l’exposition aux radiofréquences

Ce matériel est conforme aux limites établies par IC en matière d’exposition aux radiofréquences dans un environnement non contrôlé. Ce matériel doit être installé et utilisé à une distance d’au moins 20 cm entre l’antenne et le corps de l’utilisateur.

L’émetteur ne doit pas être placé près d’une autre antenne ou d’un autre émetteur, ou fonctionner avec une autre antenne ou un autre émetteur.

Wireless-N Broadband Router

34

Appendix D

Regulatory Information

Declaration of Conformity with Regard to EU Directive 1999/5/EC (R&TTE Directive)

Compliance Information for 2.4-GHz and 5-GHz Wireless Products Relevant to the EU and Other Countries Following the EU Directive 1999/5/EC (R&TTE Directive)

Бъ л га р ск и [Bulgarian]

Česky [Czech]:

Dansk [Danish]:

Deutsch [German]:

Eesti [Estonian]:

Това оборудване отговаря на съществените изисквания и приложими клаузи на Директива 1999/5/ЕС.

Toto zařízení je v souladu se základními požadavky a ostatními odpovídajícími ustanoveními Směrnice 1999/5/EC.

Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i Direktiv 1999/5/EF.

Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden Vorgaben der Richtlinie 1999/5/EU.

See seade vastab direktiivi 1999/5/EÜ olulistele nõuetele ja teistele asjakohastele sätetele.

Nederlands [Dutch]:

Malti [Maltese]:

Magyar [Hungarian]:

Norsk [Norwegian]:

Polski [Polish]:

Português [Portuguese]:

Română [Romanian]

Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de Richtlijn 1999/5/EC.

Dan l-apparat huwa konformi mal-ħtiġiet essenzjali u l-provedimenti l-oħra rilevanti tad-Direttiva 1999/5/EC.

Ez a készülék teljesíti az alapvető követelményeket és más 1999/5/EK irányelvben meghatározott vonatkozó rendelkezéseket.

Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-direktiv 1999/5/EF.

Urządzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi warunkami określonymi Dyrektywą UE: 1999/5/EC.

Este equipamento está em conformidade com os requisitos essenciais e outras provisões relevantes da Directiva 1999/5/EC.

Acest echipament este in conformitate cu cerintele esentiale si cu alte prevederi relevante ale Directivei 1999/5/EC.

English:

Español [Spanish]:

Ελληνική [Greek]:

Français [French]:

Íslenska [Icelandic]:

Italiano [Italian]:

Latviski [Latvian]:

Lietuvių [Lithuanian]:

This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directiva 1999/5/CE.

Αυτός ο εξοπλισµός είναι σε συµµόρφωση µε τις ουσιώδεις απαιτήσεις και άλλες σχετικές διατάξεις της Οδηγίας 1999/5/EC.

Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la Directive 1999/5/EC.

Þetta tæki er samkvæmt grunnkröfum og öðrum viðeigandi ákvæðum Tilskipunar 1999/5/EC.

Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva 1999/5/CE.

Šī iekārta atbilst Direktīvas 1999/5/ EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.

Šis įrenginys tenkina 1999/5/EB Direktyvos esminius reikalavimus ir kitas šios direktyvos nuostatas.

Slovensko [Slovenian]:

Slovensky [Slovak]:

Suomi [Finnish]:

Svenska [Swedish]:

Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi pogoji Direktive 1999/5/EC.

Toto zariadenie je v zhode so základnými požiadavkami a inými príslušnými nariadeniami direktív: 1999/5/EC.

Tämä laite täyttää direktiivin 1999/5/EY olennaiset vaatimukset ja on siinä asetettujen muiden laitetta koskevien määräysten mukainen.

Denna utrustning är i överensstämmelse med de väsentliga kraven och andra relevanta bestämmelser i Direktiv 1999/5/EC.

For all products, the Declaration of Conformity (DofC) is available through one or more of these options:

• A pdf file is included on the product’s CD.

• A print copy is included with the product.

• A pdf file is available on the product’s webpage.

Visit www.linksysbycisco.com/international and select your country or region. Then select your product.

If you need any other technical documentation, see the “Technical Documents on www.linksysbycisco.com/ international” section, as shown later in this appendix.

Wireless-N Broadband Router

35

Appendix D

XXXX

Regulatory Information

Wireless Equipment (Wireless-N/G/A/B Products)

The following standards were applied during the assessment of the product against the requirements of the Directive 1999/5/EC:

• Radio: EN 300 328 and/or EN 301 893 as applicable

• EMC: EN 301 489-1, EN 301 489-17

• Safety: EN 60950 and either EN 50385 or EN 50371

Dynamic Frequency Selection (DFS) and Transmit Power Control (TPC) are required for operation in the 5 GHz band.

DFS: The equipment meets the DFS requirements as defined in ETSI EN 301 893. This feature is required by the regulations to avoid interference with Radio Location Services (radars).

TPC: For operation in the 5 GHz band, the maximum power level is 3 dB or more below the applicable limit. As such, TPC is not required.

CE Marking

For the Linksys Wireless-N, -G, -B and/or -A products, the following CE mark, notified body number (where applicable) and class 2 identifier are added to the equipment.

In the majority of the EU and other European countries, the 2.4- and 5-GHz bands have been made available for the use of wireless local area networks (LANs). The table labelled “Overview of Regulatory Requirements for Wireless LANs” provides an overview of the regulatory requirements applicable for the 2.4- and 5-GHz bands.

Later in this document you will find an overview of countries in which additional restrictions or requirements or both are applicable.

The requirements for any country may evolve. Linksys recommends that you check with the local authorities for the latest status of their national regulations for both the

2.4- and 5-GHz wireless LANs.

Overview of Regulatory Requirements for Wireless LANs

Frequency

Band (MHz)

2400-2483,5 100 X

5150-5250 200 X

5250-5350

5470-5725

†Dynamic Frequency Selection and Transmit Power Control are required

in the frequency ranges of 5250-5350 MHz and 5470-5725 MHz.

The following countries have restrictions and/or requirements in addition to those given in the table labelled “Overview of Regulatory Requirements for Wireless LANs”:

Max Power Level

†

Indoor

(EIRP) (mW)

200 X

1000 X

ONLY

Indoor &

Outdoor

or

Check the CE label on the product to find out which notified body was involved during the assessment.

National Restrictions

This product may be used in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:

Ce produit peut être utilisé dans tous les pays de l’UE (et dans tous les pays ayant transposés la directive 1999/5/CE) sans aucune limitation, excepté pour les pays mentionnés cidessous:

Questo prodotto è utilizzabile in tutte i paesi EU (ed in tutti gli altri paesi che seguono le direttive EU 1999/5/EC) senza nessuna limitazione, eccetto per i paesi menzionati di seguito:

Das Produkt kann in allen EU Staaten ohne Einschränkungen eingesetzt werden (sowie in anderen Staaten die der EU Direktive 1999/5/CE folgen) mit Außnahme der folgenden aufgeführten Staaten:

Wireless-N Broadband Router

Croatia

License is required in the band 5150-5350 MHz.

Za pojas od 5150-5350 MHz potrebna je licenca.

Denmark

In Denmark, the band 5150 - 5350 MHz is also allowed for outdoor usage.

I Danmark må frekvensbåndet 5150 - 5350 også anvendes udendørs.

France

For 2,4 GHz, the product is allowed to be used outdoors in the band 2454 - 2483,5 MHz with the condition of eirp limited to 10mW (10 dBm). When operating in the band 2400-2454 MHz, it is restricted for indoor and outdoor use with eirp limited to 100mW (20 dBm). Check http://www.arcep.fr/ for more details.

Pour la bande 2,4 GHz, l’équipement peut être utilisé en extérieur dans la bande 2 454 – 2 483,5 MHz, seulement si la puissance PIRE ne dépasse pas 10 mW (10 dBm). Lors du fonctionnement dans la bande 2 400 – 2 454 MHz, l’utilisation est limitée en intérieur et en extérieur avec une

36

Appendix D

Regulatory Information

puissance PIRE de à 100 mW (20 dBm) maximum. Consultez

http://www.arcep.fr/ pour de plus amples détails.

Applicable Power Levels in France

Frequency

Band (MHz)

2400-2454 100 (20 dBm) X X

2454-2483,5 100 (20 dBm) X

2454-2483,5 10 (10 dBm) X

Power Level

(EIRP), (mW)

Indoor Outdoor

Italy

This product meets the National Radio Interface and the requirements specified in the National Frequency Allocation Table for Italy. Unless this 2,4-GHz wireless LAN product is operating within the boundaries of the owner’s property, its use requires a “general authorization”. Bands 5150-5350 MHz and 5470-5725 MHz require general authorization if used outdoors. Please check http://www.comunicazioni.it/it/ for more details.

Questo prodotto è conforme alla specifiche di Interfaccia Radio Nazionali e rispetta il Piano Nazionale di ripartizione delle frequenze in Italia. Se non viene installato all’interno del proprio fondo, l’utilizzo di prodotti Wireless LAN a 2,4 GHz richiede una “Autorizzazione Generale”. L’utilizzo all’aperto delle bande di frequenza 5150-5350 MHz e 54705725 MHz è soggetto ad autorizzazione generale. Consultare http://www.comunicazioni.it/it/ per maggiori dettagli.

Latvia

The outdoor usage of the 2,4 GHz band requires an authorization from the Electronic Communications Office. Please check http://www.esd.lv for more details.

2,4 GHz frekveču joslas izmantošanai ārpus telpām nepieciešama atļauja no Elektronisko sakaru direkcijas. Vairāk informācijas: http://www.esd.lv.

Notes:

1. Although Norway, Switzerland and Liechtenstein are not EU member states, the EU Directive 1999/5/EC has also been implemented in those countries.

2. The regulatory limits for maximum output power are specified in EIRP. The EIRP level of a device can be calculated by adding the gain of the antenna used (specified in dBi) to the output power available at the connector (specified in dBm).

2.4 GHz Restrictions

This product is designed for use with the standard, integral or dedicated (external) antenna(s) that is/are shipped together with the equipment. However, some applications may require the antenna(s), if removable, to be separated from the product and installed remotely from the device by using extension cables. For these applications, Linksys offers an R-SMA extension cable (AC9SMA) and an R-TNC extension cable (AC9TNC). Both of these cables are 9 metres long and have a cable loss (attenuation) of 5 dB. To compensate for the attenuation, Linksys also offers higher gain antennas, the HGA7S (with R-SMA connector) and HGA7T (with R-TNC connector). These antennas have a gain of 7 dBi and may only be used with either the R-SMA or R-TNC extension cable.

Combinations of extension cables and antennas resulting in a radiated power level exceeding 100 mW EIRP are illegal.

Third-Party Software or Firmware

The use of software or firmware not supported/provided by Linksys may result in the equipment no longer being compliant with the regulatory requirements.

Technical Documents on www.linksysbycisco.com/international

Follow these steps to access technical documents:

1. Enter http://www.linksysbycisco.com/international

in your web browser.

2. Select the country or region in which you live.

3. Click the Products tab.

4. Select the appropriate product category.

5. Select the product sub-category, if necessary.

6. Select the product.

7. Select the type of documentation you want from the More Information section. The document will open in PDF format if you have Adobe Acrobat installed on your computer.

NOTE: If you have questions regarding

the compliance of this product or you cannot find the information you need, please contact your local sales office or visit

www.linksysbycisco.com/international

Product Usage Restrictions

This product is designed for indoor usage only. Outdoor usage is not recommended, unless otherwise noted.

Wireless-N Broadband Router

37

Appendix D

Regulatory Information

User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE)

This document contains important information for users with regards to the proper disposal and recycling of Linksys products. Consumers are required to comply with this notice for all electronic products bearing the following symbol:

English - Environmental Information for Customers in the European Union

European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.

Български (Bulgarian) - Информация относно опазването на околната среда за потребители в Европейския съюз

Европейска директива 2002/96/EC изисква уредите, носещи този символ върху изделието и/или опаковката му, да не се изхвърля т с несортирани битови отпадъци. Символът обозначава, че изделието трябва да се изхвърля отделно от сметосъбирането на обикновените битови отпадъци. Ваша е отговорността този и другите електрически и електронни уреди да се изхвърлят в предварително определени от държавните или общински органи специализирани пунктове за събиране. Правилното изхвърляне и рециклиране ще спомогнат да се предотвратят евентуални вредни за околната среда и здравето на населението последствия. За по-подробна информация относно изхвърлянето на вашите стари уреди се обърнете към местните власти, службите за сметосъбиране или магазина, от който сте закупили уреда.

Čeština (Czech) - Informace o ochraně životního prostředí pro zákazníky v zemích Evropské unie

Evropská směrnice 2002/96/ES zakazuje, aby zařízení označené tímto symbolem na produktu anebo na obalu bylo likvidováno s netříděným komunálním odpadem. Tento symbol udává, že daný produkt musí být likvidován odděleně od běžného komunálního odpadu. Odpovídáte za likvidaci tohoto produktu a dalších elektrických a elektronických zařízení prostřednictvím určených sběrných míst stanovených vládou nebo místními úřady. Správná likvidace a recyklace pomáhá předcházet potenciálním negativním dopadům na životní prostředí a lidské zdraví. Podrobnější informace o likvidaci starého vybavení si laskavě vyžádejte od místních úřadů, podniku zabývajícího se likvidací komunálních odpadů nebo obchodu, kde jste produkt zakoupili.

Dansk (Danish) - Miljøinformation for kunder i EU

EU-direktiv 2002/96/EF kræver, at udstyr der bærer dette symbol

på produktet og/eller emballagen ikke må bortskaffes som usorteret kommunalt affald. Symbolet betyder, at dette produkt skal bortskaffes adskilt fra det almindelige husholdningsaffald. Det er dit ansvar at bortskaffe dette og andet elektrisk og elektronisk udstyr via bestemte indsamlingssteder udpeget af staten eller de lokale myndigheder. Korrekt bortskaffelse og genvinding vil hjælpe med til at undgå mulige skader for miljøet og menneskers sundhed. Kontakt venligst de lokale myndigheder, renovationstjenesten eller den butik, hvor du har købt produktet, angående mere detaljeret information om bortskaffelse af dit gamle udstyr.

Deutsch (German) - Umweltinformation für Kunden innerhalb der Europäischen Union

Die Europäische Richtlinie 2002/96/EC verlangt, dass technische Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem Symbol versehen ist , nicht zusammen mit unsortiertem Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische und elektronische Geräte über die dafür zuständigen und von der Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei, potentielle negative Folgen für Umwelt und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das Produkt erworben haben.

Wireless-N Broadband Router

38

Appendix D

Regulatory Information

Eesti (Estonian) - Keskkonnaalane informatsioon Euroopa Liidus asuvatele klientidele

Euroopa Liidu direktiivi 2002/96/EÜ nõuete kohaselt on seadmeid, millel on tootel või pakendil käesolev sümbol , keelatud kõrvaldada koos sorteerimata olmejäätmetega. See sümbol näitab, et toode tuleks kõrvaldada eraldi tavalistest olmejäätmevoogudest. Olete kohustatud kõrvaldama käesoleva ja ka muud elektri- ja elektroonikaseadmed riigi või kohalike ametiasutuste poolt ette nähtud kogumispunktide kaudu. Seadmete korrektne kõrvaldamine ja ringlussevõtt aitab vältida võimalikke negatiivseid tagajärgi keskkonnale ning inimeste tervisele. Vanade seadmete kõrvaldamise kohta täpsema informatsiooni saamiseks võtke palun ühendust kohalike ametiasutustega, jäätmekäitlusfirmaga või kauplusega, kust te toote ostsite.

Español (Spanish) - Información medioambiental para clientes de la Unión Europea

La Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación. Es responsabilidad suya desechar este y cualesquiera otros aparatos eléctricos y electrónicos a través de los puntos de recogida que ponen a su disposición el gobierno y las autoridades locales. Al desechar y reciclar correctamente estos aparatos estará contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y la salud de las personas. Si desea obtener información más detallada sobre la eliminación segura de su aparato usado, consulte a las autoridades locales, al servicio de recogida y eliminación de residuos de su zona o pregunte en la tienda donde adquirió el producto.

Ελληνικά (Greek) - Στοιχεία περιβαλλοντικής προστασίας για πελάτες εντός της Ευρωπαϊκής Ένωσης

Σύμφωνα με την Κοινοτική Οδηγία 2002/96/EC, ο εξοπλισμός που φέρει αυτό το σύμβολο στο προϊόν ή/και τη συσκευασία του δεν πρέπει να απορρίπτεται μαζί με τα μη διαχωρισμένα αστικά απορρίμματα. Το σύμβολο υποδεικνύει ότι αυτό το προϊόν θα πρέπει να απορρίπτεται ξεχωριστά από τα συνήθη οικιακά απορρίμματα. Είστε υπεύθυνος για την απόρριψη του παρόντος και άλλου ηλεκτρικού και ηλεκτρονικού εξοπλισμού μέσω των καθορισμένων εγκαταστάσεων συγκέντρωσης απορριμμάτων, οι οποίες ορίζονται από το κράτος ή τις αρμόδιες τοπικές αρχές. Η σωστή απόρριψη και ανακύκλωση συμβάλλει στην πρόληψη ενδεχόμενων αρνητικών επιπτώσεων στο περιβάλλον και την υγεία. Για περισσότερες πληροφορίες σχετικά με την απόρριψη του παλαιού σας εξοπλισμού, επικοινωνήστε με τις τοπικές αρχές, τις υπηρεσίες αποκομιδής απορριμμάτων ή το κατάστημα από το οποίο αγοράσατε το προϊόν.

Français (French) - Informations environnementales pour les clients de l’Union européenne

La directive européenne 2002/96/CE exige que l’équipement sur lequel est apposé ce symbole sur le produit et/ou son emballage ne soit pas jeté avec les autres ordures ménagères. Ce symbole indique que le produit doit être éliminé dans un circuit distinct de celui pour les déchets des ménages. Il est de votre responsabilité de jeter ce matériel ainsi que tout autre matériel électrique ou électronique par les moyens de collecte indiqués par le gouvernement et les pouvoirs publics des collectivités territoriales. L’élimination et le recyclage en bonne et due forme ont pour but de lutter contre l’impact néfaste potentiel de ce type de produits sur l’environnement et la santé publique. Pour plus d’informations sur le mode d’élimination de votre ancien équipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des déchets, ou l’endroit où vous avez acheté le produit.

Italiano (Italian) - Informazioni relative all’ambiente per i clienti residenti nell’Unione Europea

La direttiva europea 2002/96/EC richiede che le apparecchiature contrassegnate con questo simbolo sul prodotto e/o sull’imballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti domestici. È responsabilità del proprietario smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze potenzialmente negative per l’ambiente e per la salute dell’essere umano. Per ricevere informazioni più dettagliate circa lo smaltimento delle vecchie apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto.

Latviešu valoda (Latvian) - Ekoloģiska informācija klientiem Eiropas Savienības jurisdikcijā

Direktīvā 2002/96/EK ir prasība, ka aprīkojumu, kam pievienota zīme uz paša izstrādājuma vai uz tā iesaiņojuma, nedrīkst izmest nešķirotā veidā kopā ar komunālajiem atkritumiem (tiem, ko rada vietēji iedzīvotāji un uzņēmumi). Šī zīme nozīmē to, ka šī ierīce ir jāizmet atkritumos tā, lai tā nenonāktu kopā ar parastiem mājsaimniecības atkritumiem. Jūsu pienākums ir šo un citas elektriskas un elektroniskas ierīces izmest atkritumos, izmantojot īpašus atkritumu savākšanas veidus un līdzekļus, ko nodrošina valsts un pašvaldību iestādes. Ja izmešana atkritumos un pārstrāde tiek veikta pareizi, tad mazinās iespējamais kaitējums dabai un cilvēku veselībai. Sīkākas ziņas par novecojuša aprīkojuma izmešanu atkritumos jūs varat saņemt vietējā pašvaldībā, atkritumu savākšanas dienestā, kā arī veikalā, kur iegādājāties šo izstrādājumu.

Wireless-N Broadband Router

39

Appendix D

Regulatory Information

Lietuvškai (Lithuanian) - Aplinkosaugos informacija, skirta Europos Sąjungos vartotojams

Europos direktyva 2002/96/EC numato, kad įrangos, kuri ir kurios pakuotė yra pažymėta šiuo simboliu (įveskite simbolį), negalima šalinti kartu su nerūšiuotomis komunalinėmis atliekomis. Šis simbolis rodo, kad gaminį reikia šalinti atskirai nuo bendro buitinių atliekų srauto. Jūs privalote užtikrinti, kad ši ir kita elektros ar elektroninė įranga būtų šalinama per tam tikras nacionalinės ar vietinės valdžios nustatytas atliekų rinkimo sistemas. Tinkamai šalinant ir perdirbant atliekas, bus išvengta galimos žalos aplinkai ir žmonių sveikatai. Daugiau informacijos apie jūsų senos įrangos šalinimą gali pateikti vietinės valdžios institucijos, atliekų šalinimo tarnybos arba parduotuvės, kuriose įsigijote tą gaminį.

Malti (Maltese) - Informazzjoni Ambjentali għal Klijenti fl-Unjoni Ewropea

Id-Direttiva Ewropea 2002/96/KE titlob li t-tagħmir li jkun fih is-simbolu fuq il-prodott u/jew fuq l-ippakkjar ma jistax jintrema ma’ skart muniċipali li ma ġiex isseparat. Is-simbolu jindika li dan il-prodott għandu jintrema separatament minn ma’ l-iskart domestiku regolari. Hija responsabbiltà tiegħek li tarmi dan it-tagħmir u kull tagħmir ieħor ta’ l-elettriku u elettroniku permezz ta’ faċilitajiet ta’ ġbir appuntati apposta mill-gvern jew mill-awtoritajiet lokali. Ir-rimi b’mod korrett u r-riċiklaġġ jgħin jipprevjeni konsegwenzi negattivi potenzjali għall-ambjent u għas-saħħa tal-bniedem. Għal aktar informazzjoni dettaljata dwar ir-rimi tat-tagħmir antik tiegħek, jekk jogħġbok ikkuntattja lill-awtoritajiet lokali tiegħek, is-servizzi għar-rimi ta’ l-iskart, jew il-ħanut minn fejn xtrajt il-prodott.

Nederlands (Dutch) - Milieu-informatie voor klanten in de Europese Unie

De Europese Richtlijn 2002/96/EC schrijft voor dat apparatuur die is voorzien van dit symbool op het product of de verpakking, niet mag worden ingezameld met niet-gescheiden huishoudelijk afval. Dit symbool geeft aan dat het product apart moet worden ingezameld. U bent zelf verantwoordelijk voor de vernietiging van deze en andere elektrische en elektronische apparatuur via de daarvoor door de landelijke of plaatselijke overheid aangewezen inzamelingskanalen. De juiste vernietiging en recycling van deze apparatuur voorkomt mogelijke negatieve gevolgen voor het milieu en de gezondheid. Voor meer informatie over het vernietigen van uw oude apparatuur neemt u contact op met de plaatselijke autoriteiten of afvalverwerkingsdienst, of met de winkel waar u het product hebt aangeschaft.

Norsk (Norwegian) - Miljøinformasjon for kunder i EU

EU-direktiv 2002/96/EF krever at utstyr med følgende symbol

avbildet på produktet og/eller pakningen, ikke må kastes sammen med usortert avfall. Symbolet indikerer at dette produktet skal håndteres atskilt fra ordinær avfallsinnsamling for husholdningsavfall. Det er ditt ansvar å kvitte deg med dette produktet og annet elektrisk og elektronisk avfall via egne innsamlingsordninger slik myndighetene eller kommunene bestemmer. Korrekt avfallshåndtering og gjenvinning vil være med på å forhindre mulige negative konsekvenser for miljø og helse. For nærmere informasjon om håndtering av det kasserte utstyret ditt, kan du ta kontakt med kommunen, en innsamlingsstasjon for avfall eller butikken der du kjøpte produktet.

Magyar (Hungarian) - Környezetvédelmi információ az európai uniós vásárlók számára

A 2002/96/EC számú európai uniós irányelv megkívánja, hogy azokat a termékeket, amelyeken, és/vagy amelyek csomagolásán az alábbi címke megjelenik, tilos a többi szelektálatlan lakossági hulladékkal együtt kidobni. A címke azt jelöli, hogy az adott termék kidobásakor a szokványos háztartási hulladékelszállítási rendszerektõl elkülönített eljárást kell alkalmazni. Az Ön felelõssége, hogy ezt, és más elektromos és elektronikus berendezéseit a kormányzati vagy a helyi hatóságok által kijelölt gyűjtõredszereken keresztül számolja fel. A megfelelõ hulladékfeldolgozás segít a környezetre és az emberi egészségre potenciálisan ártalmas negatív hatások megelõzésében. Ha elavult berendezéseinek felszámolásához további részletes információra van szüksége, kérjük, lépjen kapcsolatba a helyi hatóságokkal, a hulladékfeldolgozási szolgálattal, vagy azzal üzlettel, ahol a terméket vásárolta.

Polski (Polish) - Informacja dla klientów w Unii Europejskiej o przepisach dotyczących ochrony środowiska

Dyrektywa Europejska 2002/96/EC wymaga, aby sprzęt oznaczony symbolem znajdującym się na produkcie i/lub jego opakowaniu nie był wyrzucany razem z innymi niesortowanymi odpadami komunalnymi. Symbol ten wskazuje, że produkt nie powinien być usuwany razem ze zwykłymi odpadami z gospodarstw domowych. Na Państwu spoczywa obowiązek wyrzucania tego i innych urządzeń elektrycznych oraz elektronicznych w punktach odbioru wyznaczonych przez władze krajowe lub lokalne. Pozbywanie się sprzętu we właściwy sposób i jego recykling pomogą zapobiec potencjalnie negatywnym konsekwencjom dla środowiska i zdrowia ludzkiego. W celu uzyskania szczegółowych informacji o usuwaniu starego sprzętu, prosimy zwrócić się do lokalnych władz, służb oczyszczania miasta lub sklepu, w którym produkt został nabyty.

Wireless-N Broadband Router

40

Appendix D

Regulatory Information

Português (Portuguese) - Informação ambiental para clientes da União Europeia

A Directiva Europeia 2002/96/CE exige que o equipamento que exibe este símbolo no produto e/ou na sua embalagem não seja eliminado junto com os resíduos municipais não separados. O símbolo indica que este produto deve ser eliminado separadamente dos resíduos domésticos regulares. É da sua responsabilidade eliminar este e qualquer outro equipamento eléctrico e electrónico através das instalações de recolha designadas pelas autoridades governamentais ou locais. A eliminação e reciclagem correctas ajudarão a prevenir as consequências negativas para o ambiente e para a saúde humana. Para obter informações mais detalhadas sobre a forma de eliminar o seu equipamento antigo, contacte as autoridades locais, os serviços de eliminação de resíduos ou o estabelecimento comercial onde adquiriu o produto.

Română (Romanian) - Informaţii de mediu pentru clienţii din Uniunea Europeană

Directiva europeană 2002/96/CE impune ca echipamentele care prezintă acest simbol pe produs şi/sau pe ambalajul acestuia să nu fie casate împreună cu gunoiul menajer municipal. Simbolul indică faptul că acest produs trebuie să fie casat separat de gunoiul menajer obişnuit. Este responsabilitatea dvs. să casaţi acest produs şi alte echipamente electrice şi electronice prin intermediul unităţilor de colectare special desemnate de guvern sau de autorităţile locale. Casarea şi reciclarea corecte vor ajuta la prevenirea potenţialelor consecinţe negative asupra sănătăţii mediului şi a oamenilor. Pentru mai multe informaţii detaliate cu privire la casarea acestui echipament vechi, contactaţi autorităţile locale, serviciul de salubrizare sau magazinul de la care aţi achiziţionat produsul.

Slovenčina (Slovak) - Informácie o ochrane životného prostredia pre zákazníkov v Európskej únii

Podľa európskej smernice 2002/96/ES zariadenie s týmto symbolom na produkte a/alebo jeho balení nesmie byť likvidované spolu s netriedeným komunálnym odpadom. Symbol znamená, že produkt by sa mal likvidovať oddelene od bežného odpadu z domácností. Je vašou povinnosťou likvidovať toto i ostatné elektrické a elektronické zariadenia prostredníctvom špecializovaných zberných zariadení určených vládou alebo miestnymi orgánmi. Správna likvidácia a recyklácia pomôže zabrániť prípadným negatívnym dopadom na životné prostredie a zdravie ľudí. Ak máte záujem o podrobnejšie informácie o likvidácii starého zariadenia, obráťte sa, prosím, na miestne orgány, organizácie zaoberajúce sa likvidáciou odpadov alebo obchod, v ktorom ste si produkt zakúpili.

Slovenščina (Slovene) - Okoljske informacije za stranke v Evropski uniji

Evropska direktiva 2002/96/ES prepoveduje odlaganje opreme s tem simbolom – na izdelku in/ali na embalaži z nesortiranimi komunalnimi odpadki. Ta simbol opozarja, da je treba izdelek zavreči ločeno od preostalih gospodinjskih odpadkov. Vaša odgovornost je, da to in preostalo električno in elektronsko opremo oddate na posebna zbirališča, ki jih določijo državne ustanove ali lokalne oblasti. S pravilnim odlaganjem in recikliranjem boste preprečili morebitne škodljive vplive na okolje in zdravje ljudi. Če želite izvedeti več o odlaganju stare opreme, se obrnite na lokalne oblasti, odlagališče odpadkov ali trgovino, kjer ste izdelek kupili.

Suomi (Finnish) - Ympäristöä koskevia tietoja EUalueen asiakkaille

EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämä symboli itse tuotteessa ja/tai sen pakkauksessa, laitteistoa ei saa hävittää lajittelemattoman yhdyskuntajätteen mukana. Symboli merkitsee sitä, että tämä tuote on hävitettävä erillään tavallisesta kotitalousjätteestä. Sinun vastuullasi on hävittää tämä elektroniikkatuote ja muut vastaavat elektroniikkatuotteet viemällä tuote tai tuotteet viranomaisten määräämään keräyspisteeseen. Laitteiston oikea hävittäminen estää mahdolliset kielteiset vaikutukset ympäristöön ja ihmisten terveyteen. Lisätietoja vanhan laitteiston oikeasta hävitystavasta saa paikallisilta viranomaisilta, jätteenhävityspalvelusta tai siitä myymälästä, josta ostit tuotteen.

Svenska (Swedish) - Miljöinformation för kunder i Europeiska unionen

Det europeiska direktivet 2002/96/EC kräver att utrustning med denna symbol på produkten och/eller förpackningen inte får kastas med osorterat kommunalt avfall. Symbolen visar att denna produkt bör kastas efter att den avskiljts från vanligt hushållsavfall. Det faller på ditt ansvar att kasta denna och annan elektrisk och elektronisk utrustning på fastställda insamlingsplatser utsedda av regeringen eller lokala myndigheter. Korrekt kassering och återvinning skyddar mot eventuella negativa konsekvenser för miljön och personhälsa. För mer detaljerad information om kassering av din gamla utrustning kontaktar du dina lokala myndigheter, avfallshanteringen eller butiken där du köpte produkten.

WEB: For additional information, please visit

www.linksysbycisco.com

Wireless-N Broadband Router

41

Appendix E

Software End User License Agreement

Appendix E: Software End User License Agreement

Cisco Products

This product from Cisco Systems, Inc. or its subsidiary licensing the Software instead of Cisco Systems, Inc. (“Cisco”) contains software (including firmware) originating from Cisco and its suppliers and may also contain software from the open source community.

Any software originating from Cisco and its suppliers is licensed under the Cisco Software License Agreement contained at Schedule 1 below. You may also be prompted to review and accept the Cisco Software License Agreement upon installation of the software. Separate terms and features of Network Magic, a Cisco Software product, are set forth in Schedule 2 below.

Any software from the open source community is licensed under the specific license terms applicable to that software made available by Cisco at www.linksysbycisco.com/gpl or as provided for in Schedule 3 below. By using the Software, you acknowledge that you have reviewed such license terms and that you agree to be bound by the terms of such licenses. Where such specific license terms entitle you to the source code of such software, that source code is available upon request at cost from Cisco for at least three years from the purchase date of this product and may also be available for download from www.linksysbycisco.com/gpl. For detailed license terms and additional information on open source software in Cisco products please look at the Cisco public web site at: www.linksysbycisco.com/gpl/ or Schedule 3 below as applicable. If you would like a copy of the GPL or certain other open source code in this Software on a CD, Cisco will mail to you a CD with such code for $9.99 plus the cost of shipping, upon request.

THIS SOFTWARE END USER LICENSE AGREEMENT IS A LEGAL AGREEMENT BETWEEN YOU AND CISCO. READ IT CAREFULLY BEFORE INSTALLING AND USING THE SOFTWARE. IT PROVIDES A LICENSE TO USE THE SOFTWARE AND CONTAINS WARRANTY INFORMATION AND LIABILITY DISCLAIMERS. BY CHECKING THE “I ACCEPT” BOX, DOWNLOADING, INSTALLING OR USING THE SOFTWARE, OR USING THE PRODUCT CONTAINING THE SOFTWARE, YOU ARE CONFIRMING YOUR ACCEPTANCE OF THE SOFTWARE AND CONSENTING TO BE BOUND BY THIS AGREEMENT. IF YOU DO NOT AGREE TO ALL OF THESE TERMS, THEN DO NOT CLICK ON THE “I ACCEPT” BUTTON AND DO NOT DOWNLOAD, INSTALL OR USE THE SOFTWARE. YOU MAY RETURN UNUSED SOFTWARE (OR, IF THE SOFTWARE IS SUPPLIED AS PART OF ANOTHER PRODUCT, THE UNUSED PRODUCT) FOR A FULL REFUND UP TO 30 DAYS AFTER ORIGINAL PURCHASE, SUBJECT TO

THE RETURN PROCESS AND POLICIES OF THE PARTY FROM WHICH YOU PURCHASED SUCH PRODUCT OR SOFTWARE.

IN THE EVENT THAT YOU HAVE ELECTED TO OBTAIN A SUBSCRIPTION LICENSE, AS INDICATED IN YOUR ORDER, YOU ADDITIONALLY AGREE TO BE BOUND BY THE “TERMS OF SERVICE” SET FORTH IN SCHEDULE 2 IF APPLICABLE.

Software Licenses

The software licenses applicable to software from Cisco are made available at the Cisco public web site at: www.linksysbycisco.com and www.linksysbycisco.com/gpl/ respectively. For your convenience of reference, a copy of the Cisco Software License Agreement and the main open source code licenses used by Cisco in its products are contained in the Schedules below.

Schedule 1 Cisco Software License Agreement

License. Subject to the terms and conditions of this Agreement, Cisco grants the original end user purchaser of the Software a nonexclusive license to (i) use the Software solely as embedded in, as a stand-alone application or (where authorized in the applicable documentation) for communication with such product, each solely at Cisco’s discretion; (ii) if the Software is purchased separately from any Cisco Product, install the Software on personal computers within a single household or business location according to the maximum number of licenses you have purchased; and (iii) make one copy of the Software in machine-readable form and one copy of the Documentation, solely for backup purposes. This license may not be sublicensed, and is not transferable except to a person or entity to which you transfer ownership of the complete Cisco product containing the Software or complete Software product, provided you permanently transfer all rights under this Agreement and do not retain any full or partial copies of the Software, and the recipient agrees to the terms of this Agreement.

“Software” includes, and this Agreement will apply to (a) the software of Cisco or its suppliers purchased separately or provided in or with the applicable Cisco product, and (b) any upgrades, updates, bug fixes or modified versions (“Upgrades”) or backup copies of the Software supplied to you by Cisco or an authorized reseller (whether or not for a fee), provided you already hold a valid license to the original software and have paid any applicable fee for the Upgrade.

“Documentation” means all documentation and other related materials supplied by Cisco to you pursuant to this Agreement.

License Restrictions. Other than as set forth in this Agreement, you may not (i) make or distribute copies

Wireless-N Broadband Router

42

Appendix E

Software End User License Agreement

of the Software or its related Documentation, or electronically transfer the Software or Documentation from one computer to another or over a network; (ii)alter, merge, modify, adapt, decrypt or translate the Software or related Documentation, or decompile, reverse engineer, disassemble, or otherwise reduce the Software to a human-perceivable form (except to the extent expressly permitted by law notwithstanding this provision); (iii) share, sell, rent, lease, or sublicense the Software or related Documentation; (iv)modify the Software or create derivative works based upon the Software; (v) if you make a backup copy of the Software and Documentation, you must reproduce all copyright notices and any other proprietary legends found on the original Software and Documentation; (vi)use the Software for management of a business network with more than 8 computers; (vii)use the Software under any circumstances for competitive evaluation, including developing competing software; (ix)to the extent permitted under applicable law, assign, sublicense or otherwise transfer the Software unless the prospective assignee, sublicensee or transferee expressly agrees to all the terms and conditions under this Agreement.

The Software and Documentation contain trade secrets and/or copyrighted materials of Cisco or its suppliers. You will not disclose or make available such trade secrets or copyrighted material in any form to any third party.

In the event that you fail to comply with this Agreement, the license granted to you will automatically terminate, at which time you must immediately (i) stop using the Cisco Product in which the Software is embedded, or (ii) uninstall the Software and destroy all copies of the Software and Documentation where the Software is purchased separately. All other rights of both parties and all other provisions of this Agreement will survive this termination.

Ownership. The Software and Documentation are licensed and not sold to you by Cisco and the relevant third parties set forth in Schedule 3. Cisco and its licensors retain all right, title and interest, including all copyright and intellectual property rights, in and to, the Software and Documentation and all copies and portions thereof. All rights not specifically granted to you in this Agreement are reserved by Cisco and its licensors. Your use of any software product from an entity other than Cisco that may have been recommended by Cisco is governed by such software product’s end user license agreement.

Links and Advertising. Cisco may provide from within the Software links to websites or third party software products that are beyond our control. Cisco makes no representations as to the quality, suitability, functionality, or legality of any sites or products to which links may be provided, and you hereby waive any claim you might have against Cisco with respect to such sites or third party software products. Your correspondence or

business dealings with, or participation in promotions of advertisers found through the Software and any other terms, conditions, warranties, or representations associated with such dealings, are solely between you and such advertiser. You agree that Cisco is not responsible or liable for any loss or damage of any sort incurred as the result of any such dealings or as the result of the presence of such advertisers in the Cisco Software.

Collection and Processing of Information. You agree that Cisco and/or its affiliates may, from time to time, collect and process information about your Cisco product and/or the Software and/or your use of either in order (i)to enable Cisco to offer you Upgrades; (ii)to provide support and assistance with your product and/or the Software; (iii)to ensure that your Cisco product and/or the Software is being used in accordance with the terms of this Agreement; (iv) to provide improvements to the way Cisco delivers technology to you and to other Cisco customers; (v) to provide reports regarding the status and health of the network, including network traffic and application usage; (vi) to enable Cisco to comply with the terms of any agreements it has with any third parties regarding your Cisco product and/or Software; and/or (vii) to enable Cisco to comply with all applicable laws and/or regulations, or the requirements of any regulatory authority or government agency. Cisco and/ or its affiliates may collect and process this information provided that it does not identify you personally.

The reports feature of certain Software allows you to monitor the activity of computers running the Software in your home or small office. You must activate this feature in order to receive reports. If you activate the reports feature, you agree to the following: (a) the Software tracks and monitors the following components and activities in your home or office: network traffic (e.g. megabytes per hour), application usage (the foreground window is tracked and the time each application is in the foreground during active usage of the computer) and internet history. (b)For all computers on which reports feature is enabled, the above information is transmitted to servers at Cisco and/ or a third party at periodic intervals while the computer is online. This information is associated and stored with the email address supplied by you when you activated the reports feature. This information is summarized into a formal report and is emailed to the identified email address. (c) Any computer on the network running the Software can enable any other computer (on the same primary network) to generate reports. When a computer is enabled, that computer shows a notification that it is being monitored. As long as that computer is enabled, each time the Software is started the user of that particular computer will see a notification that it is being monitored by the reports feature. Any computer on the network with the Software installed can enable or disable any other computer from the reports feature.

Wireless-N Broadband Router

43

Appendix E

Software End User License Agreement

In addition, Cisco may collect and store detailed information regarding your network configuration and usage for the purpose of providing you technical networking support. The information is associated with you only when you provide a unique ID number to the support representative while you are receiving help. The unique ID is generated randomly on your computer upon installation and is completely under your control.

Your use of your Cisco product and/or the Software constitutes consent by you to Cisco’s and/or its affiliates’ collection and use of such information and, for European Economic Area (EEA) customers, to the transfer of such information to a location outside the EEA. Any information collected by your Cisco product and/or the Software is done and utilized in accordance with our Privacy Policy available at Privacy Statement. Your election to use the Cisco product and/or Software indicates your acceptance of the terms of the Cisco Privacy Policy, so please review the policy carefully and check the Web site above to review updates to it.

Software Upgrades etc. If the Software enables you to receive Upgrades, you may elect at any time to receive these Upgrades either automatically or manually. If you elect to receive Upgrades manually or you otherwise elect not to receive or be notified of any Upgrades, you may expose your Cisco product and/or the Software to serious security threats and/or some features within your Cisco product and/or Software may become inaccessible. There may be circumstances where we apply an Upgrade automatically in order to comply with changes in legislation, legal, security or regulatory requirements or as a result of requirements to comply with the terms of any agreements Cisco has with any third parties regarding your Cisco product and/or the Software. You will always be notified of any Upgrades being delivered to you. The terms of this license will apply to any such Upgrade unless the Upgrade in question is accompanied by a separate license, in which event the terms of that license will apply.

Term and Termination. You may terminate this License at any time by destroying all copies of the Software and documentation. Your rights under this License will terminate immediately without notice from Cisco if you fail to comply with any provision of this Agreement.

Limited Warranty. Cisco additionally warrants that any media on which the Software may be provided will be free from defects in materials and workmanship under normal use for a period of ninety (90) days from the date of original purchase. Your exclusive remedy and Cisco’s entire liability under this limited warranty will be for Cisco, at its option, to (a)replace the Software media, or (b)refund the purchase price of the Software media.

EXCEPT FOR THE LIMITED WARRANTY ON MEDIA SET FORTH ABOVE AND TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ALL SOFTWARE PROVIDED BY CISCO

Wireless-N Broadband Router

IS PROVIDED “AS IS” WITH ALL FAULTS AND WITHOUT WARRANTY OF ANY KIND. Without limiting the foregoing, Cisco does not warrant that the operation of the product or software will be uninterrupted or error free. Also, due to the continual development of new techniques for intruding upon and attacking networks, Cisco does not warrant that the product, software or any equipment, system or network on which the product or software is used will be free of vulnerability to intrusion or attack. The product may include or be bundled with third party software or service offerings. This limited warranty shall not apply to such third party software or service offerings. This limited warranty does not guarantee any continued availability of a third party’s service for which this product’s use or operation may require.

TO THE EXTENT NOT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY, SATISFACTORY QUALITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THE WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES ARE DISCLAIMED. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary by jurisdiction.

Disclaimer of Liabilities. TO THE EXTENT NOT PROHIBITED BY APPLICABLE LAW, IN NO EVENT WILL CISCO BE LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT, SOFTWARE OR ANY SERVICES PROVIDED IN RESPECT OF SUCH PRODUCT OR SOFTWARE, EVEN IF CISCO HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. TO THE EXTENT NOT PROHIBITED BY APPLICABLE LAW, IN NO EVENT WILL CISCO’S LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even if any warranty or remedy provided under this limited warranty fails of its essential purpose.

Technical Support. This limited warranty is neither a service nor a support contract. Information about Cisco’s current technical support offerings and policies (including any fees for support services) can be found at www.linksysbycisco.com/support.

Export. Software, including technical data, may be subject to U.S. export control laws and regulations and/or export or import regulations in other countries. You agree to comply strictly with all such laws and regulations.

U.S. Government Users. The Software and Documentation qualify as “commercial items” as defined at 48 C.F.R. 2.101 and 48 C.F.R. 12.212. All Government users acquire the Software and Documentation with only those rights herein that apply to non-governmental customers. Use of

44

Appendix E

Software End User License Agreement

either the Software or Documentation or both constitutes agreement by the Government that the Software and Documentation are “commercial computer software” and “commercial computer software documentation,” and constitutes acceptance of the rights and restrictions herein.

General Terms. This Agreement will be governed by and construed in accordance with the laws of the State of California, without reference to conflict of laws principles. The United Nations Convention on Contracts for the International Sale of Goods will not apply. If any portion of this Agreement is found to be void or unenforceable, the remaining provisions will remain in full force and effect. This Agreement constitutes the entire agreement between the parties with respect to the Software and supersedes any conflicting or additional terms contained in any purchase order or elsewhere.

Linksys, Cisco and the Cisco Logo and other trademarks contained in the Software and Documentation are trademarks or registered trademarks of Linksys, Cisco, its licensors and third parties, as the case may be. You may not remove or alter any trademark, trade names, product names, logo, copyright or other proprietary notices, legends, symbols or labels in the Software and Documentation. This Agreement does not authorize you to use Cisco’s or its licensors’ names or respective trademarks.

www.networkmagic.com/support of such cancellation and uninstalling the Software and discontinuing your use of the Service. Cisco may provide notice by e-mail, via Network Magic, or by publishing the changes on its Web site.

3. Email Notification. Cisco may send you email from time to time to let you know about new products and services that are available to you. You will be able to opt-out of receiving these emails using the link provided within the email. Cisco reserves the right, however, to send you Service related email messages as long as you are a subscriber to the Service. If you wish to opt-out of receiving Service related email messages, you may cancel the Service by providing written notice via www.networkmagic.com/support to Cisco of such cancellation and uninstalling the Software and discontinuing your use of the Service.

4. WARRANTY DISCLAIMER FOR SERVICES. TO THE EXTENT NOT PROHIBITED BY APPLICABLE LAW THE SERVICES ARE PROVIDED ON AN “AS-IS” BASIS, AND CISCO AND ITS SUPPLIERS DISCLAIM ALL WARRANTIES AND REPRESENTATIONS REGARDING THE SERVICES, WHETHER EXPRESS, IMPLIED, OR OTHERWISE, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, NON-INFRINGEMENT, TITLE, QUIET ENJOYMENT, QUALITY, AND ACCURACY. CISCO DOES NOT WARRANT THAT THE SERVICE IS ERROR-FREE OR THAT THE SERVICE WILL OPERATE WITHOUT INTERRUPTION

END OF SCHEDULE 1

Schedule 2 Network Magic Features

Network Magic License Restrictions. Other than as set forth in this Agreement, you may not install or execute the Network Magic Software on any non-personal computer product, including, but not limited to, a Web appliance, set top box, handheld device, phone, Web pad device, or any device running the Microsoft Windows CE operating system.

Terms of Service for Subscription Licenses. These Terms of Service only apply if you have obtained a subscription license to Network Magic as specified in your order.

1. Network Magic Cancellation. You may cancel the Services at any time. If you cancel the Services, Cisco will not be obligated to provide you any Network Magic product Upgrades. To the extent not prohibited by applicable law, you understand and agree that cancellation of your Services is your sole remedy with respect to any dispute with Cisco.

2. Modifications. Cisco may modify or cancel the terms of this Agreement or the price, content, or nature of the Services (including discontinuing the Services program), upon notice to you. If Cisco modifies any of these terms, you may cancel the Service by providing written notice to Cisco via

Wireless-N Broadband Router

END OF SCHEDULE 2

Schedule 3 Open Source and Third Party Licenses

Schedule 3-A

If this Cisco product contains open source software licensed under Version 2 of the “GNU General Public License” then the license terms below in this Schedule 3-A will apply to that open source software. The license terms below in this Schedule 3-A are from the public web site at

http://www.gnu.org/copyleft/gpl.html

GNU GENERAL PUBLIC LICENSE

Version 2, June 1991

51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your

45

Appendix E

Software End User License Agreement

freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public License instead.) You can apply it to your programs, too.

When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.

To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.

For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.

We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.

Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors’ reputations.

Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all.

The precise terms and conditions for copying, distribution and modification follow.

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

0. This License applies to any program or other work

which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/ or translated into another language. (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”.

Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.

1. You may copy and distribute verbatim copies of the

Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2. You may modify your copy or copies of the Program

or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:

a. You must cause the modified files to carry

prominent notices stating that you changed the files and the date of any change.

b. You must cause any work that you distribute or

publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.

Wireless-N Broadband Router

46

Appendix E

Software End User License Agreement

c. If the modified program normally reads commands

interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.)

These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program.

In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.

3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following:

a. Accompany it with the complete corresponding

machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,

b. Accompany it with a written offer, valid for at least

three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,

c. Accompany it with the information you received as

to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)

The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.

If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.

4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.

6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.

Wireless-N Broadband Router

47

Appendix E

Software End User License Agreement

7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does

Wireless-N Broadband Router

not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.

10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

END OF SCHEDULE 3-A

Schedule 3-B

If this Cisco product contains open source software licensed under Version 2.1 of the “GNU Lesser General Public License” then the license terms below in this Schedule 3-B will apply to that open source software. The license terms below in this Schedule 3-B are from the public web site at

http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html

48

Appendix E

Software End User License Agreement

GNU LESSER GENERAL PUBLIC LICENSE

Version 2.1, February 1999

51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.]

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software—to make sure the software is free for all its users.

This license, the Lesser General Public License, applies to some specially designated software packages—typically libraries—of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below.

When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things.

To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it.

For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights.

We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/ or modify the library.

To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author’s reputation will not be affected by problems that might be introduced by others.

Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license.

Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free programs.

When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library.

We call this license the “Lesser” General Public License because it does Less to protect the user’s freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances.

For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License.

In other cases, permission to use a particular library in nonfree programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.

Although the Lesser General Public License is Less protective of the users’ freedom, it does ensure that the user of a program that is linked with the Library has the

Wireless-N Broadband Router

49

Appendix E

Software End User License Agreement

freedom and the wherewithal to run that program using a modified version of the Library.

The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a “work based on the library” and a “work that uses the library”. The former contains code derived from the library, whereas the latter must be combined with the library in order to run.

GNU LESSER GENERAL PUBLIC LICENSE

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called “this License”). Each licensee is addressed as “you”.

A “library” means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables.

The “Library”, below, refers to any such software library or work which has been distributed under these terms. A “work based on the Library” means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term “modification”.)

“Source code” for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library.

Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does.

Wireless-N Broadband Router

1. You may copy and distribute verbatim copies of the Library’s complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:

a) The modified work must itself be a software

library.

b) You must cause the files modified to carry

prominent notices stating that you changed the files and the date of any change.

c) You must cause the whole of the work to be

licensed at no charge to all third parties under the terms of this License.

d) If a facility in the modified Library refers to a function

or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.

(For example, a function in a library to compute square roots has a purpose that is entirely welldefined independent of the application. Therefore, Subsection 2d requires that any applicationsupplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.)

These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Library, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

50

Appendix E

Software End User License Agreement

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Library.

In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.

3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices.

Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy.

This option is useful when you wish to copy part of the code of the Library into a program that is not a library.

4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange.

If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code.

5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a “work that uses the Library”. Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License.

However, linking a “work that uses the Library” with the Library creates an executable that is a derivative of the Library (because it contains portions of the Library), rather than a “work that uses the library”. The executable is therefore covered by this License. Section 6 states terms for distribution of such executables.

When a “work that uses the Library” uses material from a header file that is part of the Library, the object code for the work may be a derivative work of the Library even though the source code is not. Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law.

If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.)

Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself.

6. As an exception to the Sections above, you may also combine or link a “work that uses the Library” with the Library to produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer’s own use and reverse engineering for debugging such modifications.

You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things:

a) Accompany the work with the complete

corresponding machine-readable source code for the Library including whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable “work that uses the Library”, as object code and/or source code, so that the user can modify the Library and then relink to produce a modified executable containing the modified Library. (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.)

Wireless-N Broadband Router

51

Appendix E

Software End User License Agreement

b) Use a suitable shared library mechanism for linking

with the Library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the user’s computer system, rather than copying library functions into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with.

c) Accompany the work with a written offer, valid

for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution.

d) If distribution of the work is made by offering access

to copy from a designated place, offer equivalent access to copy the above specified materials from the same place.

e) Verify that the user has already received a copy of

these materials or that you have already sent this user a copy.

For an executable, the required form of the “work that uses the Library” must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.

It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute.

7. You may place library facilities that are a work based on the Library side-by-side in a single library together with other library facilities not covered by this License, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things:

a) Accompany the combined library with a copy of the

same work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the Sections above.

b) Give prominent notice with the combined library of

the fact that part of it is a work based on the Library, and explaining where to find the accompanying uncombined form of the same work.

8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it.

10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this License.

11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Library.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of

Wireless-N Broadband Router

52

Appendix E

Software End User License Agreement

software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation.

14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

END OF SCHEDULE 3-B

Schedule 3-C OPENSSL LICENSE

If this Cisco product contains open source software licensed under the OpenSSL license:

This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/).

Wireless-N Broadband Router

This product includes cryptographic software written by Eric Young (eay@cryptsoft.com).

This product includes software written by Tim Hudson (tjh@cryptsoft.com).

In addition, if this Cisco product contains open source software licensed under the OpenSSL license then the license terms below in this Schedule 3-C will apply to that open source software. The license terms below in this Schedule 3-C are from the public web site at

http://www.openssl.org/source/license.html.

53

Appendix E

Software End User License Agreement

The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit. See below for the actual license texts. Actually both licenses are BSD-style Open Source licenses. In case of any license issues related to OpenSSL please contact openssl-core@openssl.org.

OpenSSL License

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgment: “This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)”

4. The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact openssl-core@openssl.org.

5. Products derived from this software may not be called “OpenSSL” nor may “OpenSSL” appear in their names without prior written permission of the OpenSSL Project.

6. Redistributions of any form whatsoever must retain the following acknowledgment: “This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)”

THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS” AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

This product includes cryptographic software written by Eric Young (eay@cryptsoft.com). This product includes software written by Tim Hudson (tjh@cryptsoft.com).

Original SSLeay License

This package is an SSL implementation written by Eric Young (eay@cryptsoft.com).

The implementation was written so as to conform with Netscape’s SSL.

This library is free for commercial and non-commercial use as long as the following conditions are adhered to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson (tjh@cryptsoft. com).

Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be removed.

If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgement:

“This product includes cryptographic software written by Eric Young (eay@cryptsoft.com)”

The word ‘cryptographic’ can be left out if the routines from the library being used are not cryptographic related.

4. If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement: “This product includes software written by Tim Hudson (tjh@ cryptsoft.com)”

THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING,

Wireless-N Broadband Router

54

Appendix E

BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

The license and distribution terms for any publicly available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution license [including the GNU Public License.]

END OF SCHEDULE 3-C

Software End User License Agreement

Wireless-N Broadband Router

9010910A-ST

55

GUÍA DEL USUARIO

Router de banda ancha

Wireless-N

Modelo: WRT160N

Acerca de esta guía

Descripciones de los iconos

Al leer la Guía del usuario pueden aparecer varios iconos que llaman la atención sobre ciertos aspectos. A continuación, se describen dichos iconos:

NOTA: Esta marca de verificación indica que hay una

nota útil a la que se debe prestar especial atención mientras se utiliza el producto.

ADVERTENCIA: Este signo de exclamación indica la

existencia de algún elemento que podría provocar daños en las instalaciones o en el producto.

WEB: Este icono con forma de globo terráqueo

indica que se trata de una dirección de correo electrónico o una dirección web de interés.

Acerca de esta guía

Recursos en línea

Las direcciones de los sitios web de este documento aparecen sin http:// delante de ellas, ya que la mayoría de los exploradores actuales no lo requieren. Si utiliza un explorador web más antiguo, es posible que deba agregar http:// delante de la dirección.

Recurso Sitio web

Linksys www.linksys.es

Linksys International www.linksys.com/international

Glosario www.linksys.com/glossary

Seguridad de red www.linksys.com/security

Copyright y marcas comerciales

Linksys, Cisco y el logotipo de Cisco son marcas registradas o marcas comerciales de Cisco Systems, Inc. o sus filiales en EE. UU. y otros países. Copyright © 2009 Cisco Systems, Inc. Todos los derechos reservados. Otras marcas y nombres de productos son marcas comerciales o marcas registradas de sus respectivos propietarios.

Router de banda ancha Wireless-N

i

Contenido

Capítulo 1: Descripción del producto 4

Panel frontal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Panel posterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Posiciones de colocación. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Capítulo 2: Lista de comprobación de seguridad inalámbrica 6

Directrices generales de seguridad de la red . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Sugerencias de seguridad adicionales . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Capítulo 3: Conguración avanzada 7

Setup > Basic Setup (Conguración > Conguración básica) . . . . . . . . . . . . . . . . . . 7

Setup (Conguración) > DDNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Setup > MAC Address Clone (Conguración > Clonación de direcciones MAC) . . . . . .12

Setup > Advanced Routing (Conguración > Enrutamiento avanzado) . . . . . . . . . . .12

Wireless > Basic Wireless Settings (Inalámbrico > Parámetros inalámbricos básicos) . . . . 13

Wireless > Wireless Security (Inalámbrico > Seguridad inalámbrica) . . . . . . . . . . . . .14

Wireless > Wireless MAC Filter (Inalámbrico > Wireless > Advanced Wireless Settings (Inalámbrico > Parámetros inalámbricos

avanzados). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Security (Seguridad) > Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Security > VPN Passthrough (Seguridad > Paso a través de VPN). . . . . . . . . . . . . . . .18

Access Restrictions (Restricciones de acceso) > Acceso a Internet . . . . . . . . . . . . . . .19

Applications and Gaming > Single Port Forwarding (Aplicaciones y juegos >

Reenvío de puerto único) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Applications and Gaming > Port Range Forwarding (Aplicaciones y juegos >

Reenvío de intervalos de puertos) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Applications & Gaming > Port Range Triggering (Aplicaciones y juegos >

Desencadenado de intervalos de puertos) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Applications and Gaming (Aplicaciones y juegos) > DMZ . . . . . . . . . . . . . . . . . . . .22

Applications and Gaming (Aplicaciones y juegos) > QoS . . . . . . . . . . . . . . . . . . . .22

Administration > Management (Administración > Gestión). . . . . . . . . . . . . . . . . . .24

Administration > Log (Administración > Registro) . . . . . . . . . . . . . . . . . . . . . . . . .25

Administration > Diagnostics (Administración > Diagnóstico) . . . . . . . . . . . . . . . . .25

Administration > Factory Defaults (Administración > Parámetros

predeterminados de fábrica) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Administration > Firmware Upgrade (Administración > Actualización del rmware) . . . . 27

Status (Estado) > Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Status > Local Network (Estado > Red local). . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Status > Wireless Network (Estado > Red inalámbrica) . . . . . . . . . . . . . . . . . . . . . .28

Filtro de MAC inalámbrico) . . . . . . . . . . .16

Router de banda ancha Wireless-N

Apéndice A: Resolución de problemas 29

Apéndice B: Especicaciones 30

ii

Contenido

Apéndice C: Información de garantía 31

Garantía limitada. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Exclusiones y limitaciones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Obtención del servicio de garantía . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Asistencia técnica . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Apéndice D: Información sobre normativa 33

FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Safety Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Industry Canada Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Avis d’Industrie Canada. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Wireless Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Avis de non-responsabilité concernant les appareils sans l . . . . . . . . . . . . . . . . . .34

Declaración de conformidad con la directiva de la UE 1999/5/CE (directiva RTTE) . . . .35

Equipo inalámbrico (productos Wireless-N/G/A/B) . . . . . . . . . . . . . . . . . . . . . . . .36

Marca CE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Restricciones nacionales . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Restricciones de uso del producto. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Documentos técnicos en www.linksys.com/international . . . . . . . . . . . . . . . . . . . .37

Información para el usuario sobre productos de consumo incluidos en la directiva

de la UE 2002/96/CE sobre residuos de aparatos eléctricos y electrónicos (WEEE). . . . .38

Apéndice E: Acuerdo de licencia del software para el usuario nal 42

Productos de Cisco . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Licencias de software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Router de banda ancha Wireless-N

iii

Capítulo 1

Descripción del producto

Capítulo 1: Descripción del producto

Gracias por elegir el router de banda ancha Wireless-N de Linksys. El router le permite acceder a Internet mediante una conexión inalámbrica o a través de uno de sus cuatro puertos conmutados. También puede utilizar el router para compartir recursos como ordenadores. Una selección de funciones de seguridad le ayuda a proteger los datos y su privacidad mientras se encuentra en línea. Entre las funciones de seguridad se incluyen seguridad WPA2, un firewall con inspección exhaustiva de paquetes (SPI) y tecnología NAT. Con la utilidad basada en explorador proporcionada es fácil configurar el router.

Panel frontal

1, 2, 3, 4 (Verde/Azul) Estas luces numeradas, que

corresponden a los puertos numerados del panel posterior del router, tienen dos finalidades. La luz está encendida de forma continua cuando el router está conectado a un dispositivo mediante ese puerto y parpadea para indicar la actividad de la red.

Conexión inalámbrica (Azul) La luz de conexión

inalámbrica se enciende cuando la función inalámbrica está activada. Si parpadea, esto indica que el router está enviando o recibiendo datos por la red.

Internet (Azul) La luz de Internet se enciende

cuando se ha establecido una conexión a través del puerto de Internet. Si parpadea, esto indica que existe actividad de red en el puerto de Internet.

Alimentación (Azul) La luz de alimentación se

ilumina y permanece encendida mientras el router está encendido. Cuando el router esté en el modo de autodiagnóstico durante el arranque, esta luz parpadeará. Cuando el diagnóstico termine, la luz quedará encendida de forma continua.

Panel posterior

Internet En este puerto se conecta la conexión a

Internet por cable o DSL.

4, 3, 2, 1 Estos puertos (4, 3, 2, 1) conectan el router

al ordenador y a otros dispositivos de red Ethernet en su red con cables.

Botón de configuración Wi-Fi protegida Si tiene

dispositivos cliente, como adaptadores inalámbricos, que admitan la configuración Wi-Fi protegida, puede hacer que esta configuración configure de forma automática la seguridad inalámbrica de sus redes inalámbricas.

Para utilizar la configuración Wi-Fi protegida, ejecute el asistente de configuración o consulte la sección “Wireless > Basic Wireless Settings (Inalámbrico > Parámetros inalámbricos básicos)” del “Capítulo 3: Configuración avanzada”.

Luz de configuración Wi-Fi protegida (Azul/ámbar)

Esta luz se ilumina en azul cuando la seguridad inalámbrica está activada. La luz parpadea en azul durante dos minutos en la configuración Wi-Fi protegida.

La luz se ilumina en ámbar si se produce un error durante el proceso de configuración Wi-Fi protegida. Asegúrese de que el dispositivo cliente es compatible con la configuración Wi-Fi protegida. Espere a que la luz se apague y vuelva a intentarlo.

La luz parpadea en ámbar cuando una sesión de configuración Wi-Fi protegida está activa y se inicia una segunda sesión. El router admite las sesiones de una en una. Espere a que la luz se apague antes de iniciar la siguiente sesión de configuración Wi-Fi protegida.

Reset (Reinicio) Hay dos formas de restablecer los

parámetros predeterminados de fábrica del router. Pulse el botón de reinicio durante unos cinco segundos o restaure los parámetros predeterminados desde Administration > Factory Defaults (Administración > Parámetros predeterminados de fábrica) en la utilidad basada en web del router.

Alimentación El adaptador de alimentación se

conectará a través del puerto de alimentación.

Posiciones de colocación

Hay dos maneras de instalar físicamente el router. La primera es colocarlo horizontalmente en una superficie. La segunda es montarlo en una pared.

Colocación horizontal

El router tiene cuatro pies de goma en el panel inferior. Coloque el router en una superficie nivelada, cerca de una toma eléctrica.

Router de banda ancha Wireless-N

4

Capítulo 1

152 mm

Descripción del producto

Colocación en la pared

El router tiene dos ranuras en el panel inferior para el montaje en pared. La distancia entre las ranuras es de 152 mm (6 pulgadas).

Se necesitan dos tornillos para montar el router.

Piezas de montaje recomendadas

4-5 mm 1-1,5 mm

Nota: Las ilustraciones de las piezas de montaje no † se muestran a escala real.

NOTA: Linksys no se hace responsable de los daños

que se produzcan por un montaje poco seguro del dispositivo en la pared.

2,5-3,0 mm

Siga estas instrucciones:

Decida dónde desea montar el router. Asegúrese de que la 1. pared elegida sea lisa, plana, sólida y esté seca. Asegúrese también de que la ubicación está cerca de una toma eléctrica.

Taladre dos orificios en la pared. Asegúrese hay una 2. separación de 152 mm (6 pulgadas) entre los orificios.

Introduzca un tornillo en cada orificio y deje que 3. sobresalga 3 mm (0,2 pulgadas).

Coloque el router de tal manera que las ranuras para 4. montaje en pared queden alineadas con los dos tornillos.

Coloque las ranuras para el montaje en pared sobre los 5. tornillos y deslice el router hacia abajo hasta que los tornillos encajen perfectamente en las ranuras.

Imprima esta página al 100 % de su tamaño.

Corte por la línea de puntos y coloque la plantilla en la pared para perforar en los puntos exactos.

Router de banda ancha Wireless-N

Plantilla para montaje en pared

5

Capítulo 2

Lista de comprobación de seguridad inalámbrica

Capítulo 2: Lista de comprobación de seguridad inalámbrica

Las redes inalámbricas son prácticas y fáciles de instalar, por lo que el número de hogares que están instalando un acceso a Internet de alta velocidad está creciendo rápidamente. Puesto que las redes inalámbricas funcionan enviando información a través de las ondas de radio, pueden ser más vulnerables frente a los intrusos que una red con cables tradicional. Al igual que las señales que emiten los teléfonos móviles o inalámbricos, las señales de la red inalámbrica también se pueden interceptar. Dado que no se puede prevenir físicamente que alguien se conecte a su red inalámbrica, deberá tomar algunas medidas adicionales para mantener la seguridad de la red.

1. Cambie el SSID o nombre predeterminado de la red inalámbrica

Los dispositivos inalámbricos tienen un nombre de red inalámbrica o identificador del conjunto de servicios (SSID) predeterminado y configurado de fábrica. Éste es el nombre de su red inalámbrica y puede tener una longitud de hasta 32 caracteres. Los productos inalámbricos de Linksys utilizan linksys como nombre predeterminado de la red inalámbrica. Debe cambiar el nombre de la red inalámbrica a algo exclusivo que distinga su red de otras redes inalámbricas que puedan existir cerca, pero no utilice información personal (como el número de la seguridad social o el DNI) porque esta información podría estar disponible para cualquier persona que busque redes inalámbricas.

ejemplo, puede especificar la dirección MAC de cada ordenador de su hogar para que sólo estos puedan acceder a su red inalámbrica.

4. Active la encriptación

La encriptación protege los datos que se transmiten a través de una red inalámbrica. El acceso Wi-Fi protegido (WPA/WPA2) y la privacidad equivalente a conexión con cables (WEP) ofrecen varios niveles de seguridad para la comunicación inalámbrica.

Una red encriptada con WPA/WPA2 es más segura que una red encriptada con WEP porque WPA/WPA2 utiliza una encriptación de clave dinámica. Para proteger la información que pasa a través de las ondas, deberá activar el nivel más alto de encriptación que admita el equipo de red.

WEP es un estándar de encriptación antiguo y puede ser la única opción disponible en algunos dispositivos que no admitan WPA.

Directrices generales de seguridad de la red

La seguridad de la red inalámbrica no sirve de nada si la red subyacente no es segura.

Una contraseña protege todos los ordenadores de la red y • la contraseña individual protege los archivos confidenciales.

Cambie las contraseñas de forma regular. •

Instale un software de antivirus y un software de firewall • personal.

Desactive el intercambio de archivos (de igual a igual). • Algunas aplicaciones pueden activar el intercambio de archivos sin su consentimiento o conocimiento.

2. Cambie la contraseña

predeterminada

Se le solicitará una contraseña cuando desee modificar los parámetros de los productos inalámbricos como puntos de acceso y routers. Estos dispositivos tienen una contraseña predeterminada configurada de fábrica. La contraseña predeterminada de Linksys es admin. Los hackers conocen estas contraseñas predeterminadas y podrían intentar utilizarlas para acceder a su dispositivo inalámbrico y cambiar los parámetros de la red. Para evitar los cambios no autorizados, personalice la contraseña del dispositivo para que resulte difícil de adivinar.

3.

Active el filtrado de direcciones MAC

Los routers de Linksys le permiten activar el filtrado de direcciones MAC (control de acceso a medios). La dirección MAC es una serie única de números y letras que se asigna a cada dispositivo de red. Sólo se proporcionará acceso a la red inalámbrica con el filtrado de direcciones MAC activado a los dispositivos inalámbricos con direcciones MAC específicas. Por

Router de banda ancha Wireless-N

Sugerencias de seguridad adicionales

Mantenga los puntos de acceso, gateways o routers • inalámbricos alejados de paredes exteriores y ventanas.

Apague los puntos de acceso, gateways o routers • inalámbricos cuando no los esté utilizando (por la noche, durante las vacaciones).

Utilice frases de paso seguras que tengan una longitud • mínima de ocho caracteres. Combine letras y números

evitar el uso de palabras estándar que puedan

para encontrarse en un diccionario.

WEB: Para obtener más información sobre la seguridad

inalámbrica, visite www.linksys.com/security.

6

Capítulo 3

Capítulo 3: Configuración avanzada

Después de configurar el router con el asistente de configuración (ubicado en el CD-ROM), el router estará listo para utilizarse. Sin embargo, si desea modificar los parámetros avanzados, utilice la utilidad basada en web del router. En este capítulo se describen las páginas web de la utilidad y las funciones clave de cada una. Puede acceder a la utilidad mediante un explorador web en un equipo conectado al router.

La utilidad basada en web cuenta con las siguientes fichas principales: Setup (Configuración), Wireless (Inalámbrico), Security (Seguridad), Access Restrictions (Restricciones de acceso), Applications & Gaming (Aplicaciones y juegos), Administration (Administración) y Status (Estado). Al hacer clic en una de las fichas principales, aparecerán fichas adicionales.

NOTA: Al instalar por primera vez el router, debería

utilizar el CD-ROM del asistente de configuración. Si desea configurar los parámetros avanzados, utilice este capítulo para obtener información sobre la utilidad basada en web.

Configuración avanzada

Cómo acceder a la utilidad basada en web

Para acceder a la utilidad basada en web, abra el explorador web en su equipo e introduzca la dirección IP predeterminada del router, 192.168.1.1, en el campo Dirección. A continuación, pulse Intro.

Aparecerá una pantalla de inicio de sesión. (Si no es usuario de Windows XP, verá una pantalla parecida). Deje el campo Usuario en blanco. La primera vez que abra la utilidad basada en web, utilice la contraseña predeterminada admin. Puede establecer una nueva contraseña en la ficha Administration (Administración) de la pantalla Management (Gestión). Haga clic en Aceptar para continuar.

Pantalla de inicio de sesión

Setup > Basic Setup (Configuración >

Setup > Basic Setup (Configuración > Configuración básica)

Internet Setup (Configuración de Internet)

En la sección Internet Setup (Configuración de Internet) se configura el router para la conexión a Internet. La mayor parte de esta información se puede obtener del ISP.

Internet Connection Type (Tipo de conexión a Internet)

Seleccione el tipo de conexión a Internet que proporcione el ISP en el menú desplegable. Estos son los tipos disponibles:

Automatic Configuration - DHCP (Configuración automática - • DHCP)

Static IP (IP estática) •

PPPoE •

PPTP •

L2TP •

Telstra Cable •

Automatic Configuration - DHCP (Configuración automática - DHCP)

De forma predeterminada, el tipo de conexión a Internet del router está establecido en Automatic Configuration - DHCP (Configuración automática - DHCP), que sólo se debe conservar si el ISP admite DHCP o si se realiza la conexión mediante una dirección IP dinámica. (Esta opción se aplica normalmente a las conexiones por cable.)

Configuración básica)

La primera pantalla que aparece es Basic Setup (Configuración básica). Permite cambiar los parámetros generales del router.

Router de banda ancha Wireless-N

Internet Connection Type > Automatic Configuration - DHCP

(Tipo de conexión a Internet > Configuración automática - DHCP)

7

Capítulo 3

Configuración avanzada

Static IP (IP estática)

Si necesita utilizar una dirección IP permanente para conectarse a Internet, seleccione Static IP (IP estática).

Internet Connection Type > Static IP (Tipo de conexión a Internet > IP estática)

Internet IP Address (Dirección IP de Internet) Se trata

de la dirección IP del router, vista desde Internet. El ISP le proporcionará la dirección IP que debe especificar aquí.

Subnet Mask (Máscara de subred) Se trata de la máscara

de subred del router, tal como la ven los usuarios en Internet (incluido el ISP). El ISP le proporcionará la máscara de subred.

Default Gateway (Gateway predeterminada) Su ISP le

proporcionará la dirección IP del servidor ISP.

DNS 1-3 El ISP le proporcionará al menos una dirección IP de

servidor DNS (sistema de nombres de dominio).

PPPoE

Algunos ISP basados en DSL utilizan PPPoE (protocolo de punto a punto en Ethernet) para establecer conexiones a Internet. Si se conecta a Internet a través de una línea DSL, consulte con el ISP si utiliza PPPoE. En ese caso, tendrá que activar PPPoE.

Internet Connection Type (Tipo de conexión a Internet) > PPPoE

User Name y Password (Nombre de usuario y Contraseña)

Introduzca el nombre de usuario y la contraseña proporcionados por el ISP.

Service Name (Nombre de servicio) Si se lo ha proporcionado

el ISP, introduzca el nombre de servicio.

Connect on Demand: Max Idle Time (Conectar cuando se

solicite: Tiempo máximo de inactividad) Puede configurar el router para que interrumpa la conexión a Internet cuando esté inactiva durante un periodo de tiempo especificado (Max Idle Time [Tiempo máximo de inactividad]). Si la conexión a Internet finaliza debido a la inactividad, Conectar cuando se solicite permite al router restablecer automáticamente la conexión si intenta acceder de nuevo a Internet. Para utilizar esta opción, seleccione Connect on Demand (Conectar cuando se solicite). En el campo Max Idle Time (Tiempo máximo de inactividad), introduzca el número de minutos que desea que transcurran para que finalice la conexión a Internet. El tiempo máximo de inactividad predeterminado es de 15 minutos.

Keep Alive: Redial Period (Mantener activo: Periodo para nueva

marcación) Si selecciona esta opción, el router comprobará

periódicamente la conexión a Internet. Si se desconecta, el router restablecerá automáticamente la conexión. Para utilizar esta opción, seleccione Keep Alive (Mantener activo).

campo Redial Period (Periodo para nueva marcación),

En el especifique compruebe la conexión a Internet. El periodo predeterminado para la nueva marcación es de 30 segundos.

la frecuencia con que desea que el router

PPTP

El protocolo de túnel de punto a punto (PPTP) es un servicio que se utiliza únicamente en conexiones europeas.

Internet Connection Type (Tipo de conexión a Internet) > PPTP

Si su ISP admite DHCP o si la conexión se realiza mediante una dirección IP dinámica, seleccione Obtain an IP Address Automatically (Obtener una dirección IP automáticamente). Si necesita utilizar una dirección IP permanente para conectarse a Internet, seleccione Specify an IP Address (Especificar una dirección IP). A continuación, realice las siguientes configuraciones:

Specify an IP Address • (Especificar una dirección IP) Se trata

de la dirección IP del router, vista desde Internet. El ISP le proporcionará la dirección IP que debe especificar aquí.

Subnet Mask • (Máscara de subred) Se trata de la máscara de

subred del router, tal como la ven los usuarios en Internet (incluido el ISP). El ISP le proporcionará la máscara de subred.

Default Gateway • (Gateway predeterminada) Su ISP le

proporcionará la dirección IP del servidor ISP.

DNS 1-3 • El ISP le proporcionará al menos una dirección

IP de servidor DNS (sistema de nombres de dominio).

PPTP Server IP Address (Dirección IP del servidor PPTP) Su

ISP le proporcionará la dirección IP del servidor PPTP.

User Name y Password (Nombre de usuario y Contraseña)

Introduzca el nombre de usuario y la contraseña proporcionados por el ISP.

Connect on Demand: Max Idle Time (Conectar cuando se

solicite: Tiempo máximo de inactividad) Puede configurar el router para que interrumpa la conexión a Internet cuando esté inactiva durante un periodo de tiempo especificado (Max Idle Time [Tiempo máximo de inactividad]). Si la conexión a Internet finaliza debido a la inactividad, Conectar cuando se solicite permite al router restablecer automáticamente la conexión si intenta acceder de nuevo a Internet. Para utilizar esta opción, seleccione Connect on Demand (Conectar cuando se solicite). En el campo Max Idle Time (Tiempo máximo de inactividad), introduzca el número de minutos que desea que transcurran

Router de banda ancha Wireless-N

8

Capítulo 3

para que finalice la conexión a Internet. El tiempo máximo de inactividad predeterminado es de 15 minutos.

Keep Alive: Redial Period (Mantener activo: Periodo para

nueva marcación) Si selecciona esta opción, el router comprobará periódicamente la conexión a Internet. Si se desconecta, el router restablecerá automáticamente la conexión. Para utilizar esta opción, seleccione Redial Period (Periodo para nueva marcación), especifique la frecuencia con que desea que el router compruebe la conexión a Internet. El valor predeterminado es de

L2TP

L2TP es un servicio que se utiliza únicamente en conexiones en Israel.

Internet Connection Type (Tipo de conexión a Internet) > L2TP

Server IP Address (Dirección IP del servidor) Ésta es la dirección

IP del servidor L2TP. El ISP le proporcionará la dirección IP que debe especificar aquí.

User Name y Password (Nombre de usuario y Contraseña)

Introduzca el nombre de usuario y la contraseña proporcionados por el ISP.

Connect on Demand: Max Idle Time (Conectar cuando se

solicite: Tiempo máximo de inactividad) Puede configurar el router para que interrumpa la conexión a Internet cuando esté inactiva durante un periodo de tiempo especificado (Max Idle Time [Tiempo máximo de inactividad]). Si la conexión a Internet finaliza debido a la inactividad, Conectar cuando se solicite permite al router restablecer automáticamente la conexión si intenta acceder de nuevo a Internet. Para utilizar esta opción, seleccione Connect on Demand (Conectar cuando se solicite). En el campo Max Idle Time (Tiempo máximo de inactividad), introduzca el número de minutos que desea que transcurran para que finalice la conexión a Internet. El tiempo máximo de inactividad predeterminado es de 15 minutos.

Keep Alive: Redial Period (Mantener activo: Periodo para nueva

marcación) Si selecciona esta opción, el router comprobará periódicamente la conexión a Internet. Si se desconecta, el router restablecerá automáticamente la conexión. Para utilizar esta opción, seleccione Keep Alive (Mantener activo). En el campo Redial Period (Periodo para nueva marcación), especifique la frecuencia con que desea que el router compruebe la conexión a Internet. El periodo predeterminado para la nueva marcación es de 30 segundos.

Telstra Cable

Telstra Cable es un servicio que se utiliza únicamente en las conexiones australianas.

Router de banda ancha Wireless-N

Keep Alive (Mantener activo). En el campo

30 segundos.

Configuración avanzada

Internet Connection Type (Tipo de conexión a Internet) > Telstra Cable

Server IP Address (Dirección IP del servidor) Ésta es la

dirección IP del servidor HeartBeat. El ISP le proporcionará la dirección IP que debe especificar aquí.

User Name y Password (Nombre de usuario y Contraseña)

Introduzca el nombre de usuario y la contraseña proporcionados por el ISP.

Connect on Demand: Max Idle Time (Conectar cuando se

solicite: Tiempo máximo de inactividad) Puede configurar el router para que interrumpa la conexión a Internet cuando esté inactiva durante un periodo de tiempo especificado (Max Idle Time [Tiempo máximo de inactividad]). Si la conexión a Internet finaliza debido a la inactividad, Conectar cuando se solicite permite al router restablecer automáticamente la conexión si intenta acceder de nuevo a Internet. Para utilizar esta opción, seleccione Connect on Demand (Conectar cuando se solicite). En el campo Max Idle Time (Tiempo máximo de inactividad), introduzca el número de minutos que desea que transcurran para que finalice la conexión a Internet. El tiempo máximo de inactividad predeterminado es de 15 minutos.

Keep Alive: Redial Period (Mantener activo: Periodo para nueva

marcación) Si selecciona esta opción, el router comprobará periódicamente la conexión a Internet. Si se desconecta, el router restablecerá automáticamente la conexión. Para utilizar esta opción, seleccione Keep Alive (Mantener activo). En el campo Redial Period (Periodo para nueva marcación), especifique la frecuencia con que desea que el router compruebe la conexión a Internet. El periodo predeterminado para la nueva marcación es de 30 segundos.

Optional Settings (Parámetros opcionales)

Es posible que el ISP exija el uso de algunos de estos parámetros. Verifique con el ISP si es necesario realizar algún cambio.

Optional Settings (Parámetros opcionales)

Host Name y Domain Name (Nombre de host y Nombre de

dominio) En estos campos puede proporcionar un nombre de host y de dominio para el router. Algunos ISP, normalmente los de cable, solicitan estos nombres como identificación. Puede que deba consultar al ISP si el servicio de Internet de banda ancha se ha configurado con un nombre de host y de dominio. En la mayoría de los casos, no habrá ningún problema si se dejan estos campos en blanco.

MTU MTU es la unidad de transmisión máxima. Especifica el

tamaño máximo de paquete permitido para la transmisión de Internet. Seleccione Manual si desea introducir manualmente el tamaño máximo de paquete que se transmitirá. Para que el router seleccione la MTU óptima para la conexión a Internet, mantenga el parámetro predeterminado, Auto (Automático).

9

Capítulo 3

Size (Tamaño) Esta opción está habilitada cuando se selecciona

Manual en el campo MTU. Este valor debe estar en el intervalo de 1200 a 1500. El tamaño predeterminado depende del tipo de conexión a Internet:

DHCP, IP estática o Telstra: • 1500

PPPoE: • 1492

PPTP o L2TP: • 1460

Network Setup (Configuración de red)

La sección Network Setup (Configuración de red) permite cambiar los parámetros de la red conectada a los puertos Ethernet del router. La configuración inalámbrica se efectúa mediante la ficha Wireless (Inalámbrico).

IP del router

Muestra la dirección IP y la máscara de subred del router tal y como las ve la red.

Router IP (IP del router)

DHCP Server Setting (Parámetro de servidor DHCP)

Los parámetros le permiten configurar la función de servidor de protocolo de configuración dinámica de host (DHCP) del router. El router se puede utilizar como servidor DHCP para la red. Un servidor DHCP asigna automáticamente una dirección IP a cada ordenador de la red. Si desea activar la opción de servidor DHCP del router, asegúrese de que no hay otro servidor DHCP en la red.

DHCP Server Setting (Parámetro de servidor DHCP)

DHCP Server (Servidor DHCP) DHCP viene activado de fábrica,

de forma predeterminada. Si ya dispone de un servidor DHCP en la red o si no desea utilizar un servidor DHCP, seleccione Disabled (Desactivado) (no estarán disponibles otras funciones de DHCP).

DHCP Reservation (Reserva DHCP) Haga clic en este botón si

desea asignar una dirección de IP local fija a una dirección MAC.

Reserva DHCP

Aparecerá una lista de los clientes DHCP con la siguiente información: Client Name (Nombre de cliente), Interface (Interfaces), IP Address (Direcciones IP) y MAC Address (Direcciones MAC).

Configuración avanzada

DHCP Reservation (Reserva DHCP)

Select Clients from DHCP Table • (Seleccionar clientes de

tablas DHCP) Haga clic en la casilla de verificación Select (Seleccionar) para reservar una dirección IP de cliente. A continuación, haga clic en Add Clients (Agregar clientes).

Manually Adding Client • (Adición manual de cliente)

Para asignar una dirección IP de forma manual, introduzca el nombre del cliente en el campo Enter Client Name (Introducir nombre de cliente). Introduzca la dirección IP que desee en el campo Assign IP Address (Asignar dirección IP). Introduzca la dirección MAC en el campo To This MAC Address (A esta dirección MAC). A continuación, haga clic en Add (Agregar).

Clients Already Reserved (Clientes ya reservados)

En la parte inferior de la pantalla aparecerá una lista de clientes DHCP y sus direcciones IP locales fijas. Si desea eliminar un cliente de la lista, haga clic en Remove (Eliminar).

Haga clic en Save Settings (Guardar parámetros) para guardar los cambios o en Cancel Changes (Cancelar cambios) para cancelarlos. Para ver la información más reciente, haga clic en Refresh (Actualizar). Para salir de esta pantalla, haga clic en Close (Cerrar).

Starting IP Address (Dirección IP inicial) Introduzca un

valor para el servidor DHCP con el que se empezarán a direcciones IP. Debido a que la dirección IP predeterminada del router es 192.168.1.1, la dirección IP inicial debe ser 192.168.1.2 o mayor, pero menor que 192.168.1.253. La dirección IP inicial predeterminada es 192.168.1.100

Maximum Number of Users (Número máximo de usuarios)

Introduzca el número máximo de ordenadores a los que desea que el servidor DHCP asigne direcciones IP. Este número no puede ser superior a 253. El valor predeterminado es 50.

IP Address Range (Intervalo de direcciones IP) Aquí se

muestra el intervalo de direcciones IP disponibles.

Client Lease Time (Tiempo de concesión del cliente) El

tiempo de concesión del cliente es la cantidad de tiempo que un usuario podrá estar conectado al router con la dirección IP dinámica actual. Introduzca el tiempo, en minutos, durante el que se “concederá” al usuario esta dirección IP dinámica. Una vez transcurrido este tiempo, al usuario se le asignará automáticamente una nueva dirección IP dinámica. De forma predeterminada es 0 minutos, lo que significa un día.

.

emitir

Router de banda ancha Wireless-N

10

Capítulo 3

Configuración avanzada

Static DNS 1-3 (DNS estático 1-3)

dominio (DNS) es el método que se utiliza en Internet para traducir los nombres de dominio o sitio web a direcciones de Internet o URL. El ISP le proporcionará al menos una dirección IP de servidor DNS. Si desea utilizar otra, introduzca dicha dirección IP en uno de estos campos. Puede introducir aquí hasta tres direcciones IP de servidor DNS. El router las utilizará para acceder más rápidamente a los servidores DNS en funcionamiento.

WINS El servicio de nombres de Internet de Windows (WINS)

administra la interacción de cada PC con Internet. Si va a utilizar un servidor WINS, introduzca aquí la dirección IP del mismo. De lo contrario, deje los campos en blanco.

El sistema de nombres de

Time Setting (Parámetro de hora)

Time Zone (Zona horaria) Seleccione la zona horaria en la

que funciona la red, en el menú desplegable. (Puede incluso ajustarla automáticamente para el horario de verano.)

Time Setting (Parámetro de hora)

Haga clic en Save Settings (Guardar parámetros) para guardar los cambios o en Cancel Changes (Cancelar cambios) para cancelarlos.

Setup (Configuración) > DDNS

El router proporciona una función de sistema dinámico de nombres de dominio (DDNS). DDNS permite asignar un nombre de host y de dominio fijo a una dirección IP dinámica de Internet. Así podrá alojar su propio sitio web, servidor FTP u otro servidor que se encuentre detrás del router.

Para poder utilizar esta función debe suscribirse al servicio DDNS con un distribuidor de dicho servicio en www.dyndns.org o www.TZO.com. Si no desea utilizar esta función, mantenga el parámetro predeterminado, Disabled (Desactivado).

DDNS

DDNS Service (Servicio DDNS)

Si DynDNS.org proporciona el servicio DDNS, seleccione DynDNS.org en el menú desplegable. Si TZO proporciona el servicio DDNS, seleccione TZO.com. Las funciones disponibles en la pantalla DDNS varían según el proveedor del servicio DDNS que utilice.

DynDNS.org

Setup (Configuración) > DDNS > DynDNS

User Name (Nombre de usuario) Introduzca el nombre de

usuario de la cuenta DDNS.

Password (Contraseña) Introduzca la contraseña de la cuenta

DDNS.

Host Name (Nombre de host) Se trata de la URL de DDNS

asignada por el servicio DDNS.

System (Sistema) Seleccione el servicio DynDNS que utiliza:

Dynamic (Dinámico), Static (Estático) o Custom (Personalizado). La selección predeterminada es Dynamic (Dinámico).

Mail Exchange (Optional) (Intercambio de correo, Opcional)

Introduzca la dirección del servidor de intercambio de correo para que los correos electrónicos de la dirección DynDNS vayan a este servidor.

Backup MX (Copia de seguridad MX) Esta función permite

que el servidor de intercambio de correo sea una copia de seguridad. Para desactivar esta función, mantenga el valor predeterminado Disabled (Desactivado). Para activar esta función, seleccione Enabled (Activado). Si no está seguro del valor que debe seleccionar, mantenga el parámetro predeterminado,

Disabled (Desactivado).

Wildcard (Comodín) Este parámetro activa o desactiva los

comodines para el host. Por ejemplo, si la dirección DDNS es

myplace.dyndns.org y activa los comodines, x.myplace.dyndns. org también funcionará (x es el comodín). Para desactivar los

comodines, mantenga el valor predeterminado, Disabled (Desactivado). Para activar comodines, seleccione Enabled (Activado). Si no está seguro del valor que debe seleccionar, mantenga el parámetro predeterminado, Disabled (Desactivado).

Internet IP Address (Dirección IP de Internet) Aquí se muestra

la dirección IP de Internet del router. Esta dirección cambiará, ya que es dinámica.

Status (Estado) Aquí se muestra el estado de la conexión del

servicio DDNS.

Update (Actualizar) Para desencadenar una actualización

manualmente, haga clic en este botón. Haga clic en Save Settings (Guardar parámetros) para

guardar los cambios o en Cancel Changes (Cancelar cambios) para cancelarlos.

Router de banda ancha Wireless-N

11

Capítulo 3

Configuración avanzada

TZO.com

Setup (Configuración) > DDNS > TZO

E-mail Address (Correo electrónico), TZO Key (Clave TZO)

y Domain Name (Nombre de dominio) Introduzca los parámetros de la cuenta que haya configurado en TZO.

Internet IP Address (Dirección IP de Internet) Aquí se muestra

la dirección IP de Internet del router. Esta dirección cambiará, ya que es dinámica.

Status (Estado) Aquí se muestra el estado de la conexión del

servicio DDNS.

Update (Actualizar) Para desencadenar una actualización

manualmente, haga clic en este botón. Haga clic en Save Settings (Guardar parámetros) para guardar

los cambios o en Cancel Changes (Cancelar cambios) para cancelarlos.

Clone Your PC’s MAC (Clonar la MAC del PC) Haga clic en este

botón para clonar la dirección MAC del ordenador que esté utilizando.

Haga clic en Save Settings (Guardar parámetros) para guardar los cambios o en Cancel Changes (Cancelar cambios) para cancelarlos.

Setup > Advanced Routing (Configuración > Enrutamiento avanzado)

Esta pantalla se utiliza para configurar las funciones avanzadas del router. En el modo de funcionamiento puede seleccionar los tipos de funciones avanzadas que utilice. Con Dynamic Routing (Enrutamiento dinámico) se ajusta automáticamente el modo en que los paquetes recorren la red. Con Enrutamiento estático (Static Routing) se puede configurar una ruta fija a otro destino de red.

Setup > MAC Address Clone (Configuración > Clonación de direcciones MAC)

Una dirección MAC es un código de 12 dígitos asignado a un dispositivo de hardware para su identificación. Algunos ISP requieren que se registre una dirección MAC para acceder a Internet. Si no desea volver a registrar la dirección MAC con el ISP, puede asignar al router la dirección MAC que tiene registrada actualmente con el ISP mediante la función de clonación de direcciones MAC.

Setup > MAC Address Clone (Configuración > Clonación de direcciones MAC)

MAC Address Clone (Clonación de direcciones MAC)

Enabled/Disabled (Activado/Desactivado) Para que se clone

la dirección MAC, seleccione Enabled (Activado).

MAC Address (Dirección MAC) Introduzca aquí la dirección

MAC registrada con el ISP.

Setup > Advanced Routing (Configuración > Enrutamiento avanzado)

Advanced Routing (Enrutamiento avanzado)

NAT

Enabled/Disabled (Activado/Desactivado) Si el router aloja

la conexión a Internet de la red, mantenga el parámetro predeterminado, Enabled (Activado). Si existe otro router en la red, seleccione Disabled (Desactivado). Cuando se desactiva el parámetro NAT, se activa el enrutamiento dinámico.

Dynamic Routing (Enrutamiento dinámico) (RIP)

Enabled/Disabled (Activado/Desactivado) Esta función permite

que el router se ajuste automáticamente a los cambios físicos que se produzcan en el diseño de la red e intercambie tablas de enrutamiento con el resto de routers. El router determina la ruta de los paquetes de red basándose en el menor número de saltos entre el origen y el destino. Cuando el parámetro NAT está activado, la función Dynamic Routing (Enrutamiento dinámico) se desactiva automáticamente. Cuando el parámetro NAT está desactivado, esta función estará disponible. Seleccione Enabled (Activado) para utilizar la función Dynamic Routing (Enrutamiento dinámico).

Static Routing (Enrutamiento estático)

Una ruta estática es la ruta predeterminada por la que se desplaza la información de red hasta alcanzar un host determinado o una red concreta. Introduzca la información descrita a continuación para configurar una nueva ruta estática.

Router de banda ancha Wireless-N

12

Capítulo 3

Configuración avanzada

Route Entries (Entradas de ruta) Para configurar una ruta

estática entre el router y otra red, seleccione un número en la lista desplegable. Haga clic en Delete This Entry (Eliminar esta entrada) para eliminar una ruta estática.

Enter Route Name (Introducir nombre de ruta) Introduzca

aquí el nombre de la ruta, con un máximo de 25 caracteres alfanuméricos.

Destination LAN IP (IP de red LAN de destino) La IP de la red

LAN de destino es la dirección de la red o el host remoto al que desea asignar una ruta estática.

Subnet Mask (Máscara de subred) La máscara de subred

determina qué parte de una dirección IP de red LAN de destino corresponde a la parte de la red y cuál a la parte del host.

Gateway Se trata de la dirección IP del dispositivo de gateway

que permite el contacto entre el router y la red o el host remoto.

Interface (Interfaz) Esta interfaz indica si la dirección IP de

destino está en LAN & Wireless (Red LAN e inalámbrica) (para redes Ethernet e inalámbricas) o WAN (Internet).

Haga clic en Show Routing Table (Mostrar tabla de enrutamiento) para ver las rutas estáticas que ya ha configurado.

Enrutamiento avanzado > Tabla de enrutamiento

Routing Table (Tabla de enrutamiento)

Para cada ruta se muestran la dirección IP de red LAN de destino, la máscara de subred, la gateway y la interfaz. Haga clic en Refresh (Actualizar) para actualizar la información. Haga clic en Close (Cerrar) para salir de esta pantalla.

Haga clic en Save Settings (Guardar parámetros) para guardar los cambios o en Cancel Changes (Cancelar cambios) para cancelarlos.

Wireless > Basic Wireless Settings (Inalámbrico > Parámetros inalámbricos básicos)

Los parámetros básicos para la red inalámbrica se establecen en esta pantalla.

Hay dos formas de configurar la red o redes inalámbricas del router: Manual y Wi-Fi Protected Setup (Configuración Wi-Fi protegida).

Ésta última facilita la configuración de la red inalámbrica. Si tiene dispositivos cliente, como adaptadores inalámbricos, que sean compatibles con la configuración Wi-Fi protegida, podrá utilizar este tipo de configuración.

Configuration View (Vista de configuración) Para configurar

una red inalámbrica de manera manual, seleccione Manual. Vaya a la sección “Basic Wireless Settings” (Parámetros inalámbricos básicos). Para utilizar la configuración Wi-Fi protegida, seleccione Wi-Fi Protected Setup (Configuración Wi-Fi protegida). Vaya a la sección “Wi-Fi Protected Setup" (Configuración Wi-Fi protegida).

Basic Wireless Settings (Parámetros inalámbricos básicos)

Inalámbrico > Parámetros inalámbricos básicos (Configuración manual)

Network Mode (Modo de red) En este menú desplegable puede

seleccionar los estándares inalámbricos que se utilizan en la red. Si cuenta con dispositivos Wireless-N, Wireless-G y Wireless-B en la red, mantenga el parámetro predeterminado, Mixed (Mixto). Si sólo dispone de dispositivos Wireless-G y Wireless-B en la red, seleccione BG-Mixed (Mixto BG). Si sólo tiene dispositivos Wireless-N, seleccione Wireless-B Only (Sólo Wireless-N). Si sólo tiene dispositivos Wireless-G, seleccione Sólo Wireless-G. Si sólo tiene dispositivos Wireless-B, seleccione Sólo Wireless-B. Si la red no tiene dispositivos inalámbricos, seleccione

Disabled (Desactivado).

Network Name (SSID) (Nombre de la red) El SSID es el

nombre de red que comparten todos los puntos de una red inalámbrica. Debe ser el mismo para todos los dispositivos de la red inalámbrica. El nombre distingue entre mayúsculas y minúsculas y no debe tener una longitud superior a los 32 caracteres (se puede utilizar cualquier carácter del teclado). Asegúrese de que este parámetro es el mismo para todos los puntos de la red inalámbrica. Para mayor seguridad, debe cambiar el SSID predeterminado (linksys) por otro.

Channel Width (Ancho de canal) Seleccione Auto (Automático)

si desea que el router determine automáticamente el ancho de canal más adecuado (20 MHz o 40 MHz), o bien seleccione la opción predeterminada 20 MHz only (Sólo 20 MHz) si desea que el router funcione sólo en modo Wireless-B y Wireless-G. Para conseguir un mejor rendimiento, se recomienda seleccionar la opción Auto (Automático).

Channel (Canal) Seleccione un canal entre 1 y 11 o la opción

predeterminada Auto (Automático).

SSID Broadcast (Difusión de SSID) Cuando los clientes

inalámbricos sondeen el área local en busca de redes inalámbricas con las que asociarse, detectarán el SSID que difunde el router. Para difundir el SSID del router, mantenga el parámetro predeterminado, Enabled (Activado). Si no desea difundir el SSID del router, seleccione Disabled (Desactivado).

Haga clic en Save Settings (Guardar parámetros) para guardar los cambios o en Cancel Changes (Cancelar cambios) para cancelarlos.

Router de banda ancha Wireless-N

13

Capítulo 3

Configuración avanzada

Wi-Fi Protected Setup (Configuración Wi-Fi protegida)

Hay tres métodos disponibles. Utilice el método que corresponda al dispositivo cliente que está configurando.

Wireless > Basic Wireless Settings (Wi-Fi Protected Setup) (Inalámbrico >

Parámetros inalámbricos básicos, Configuración Wi-Fi protegida)

NOTA: La configuración Wi-Fi protegida configura

los dispositivos cliente de uno en uno. Repita las instrucciones para cada dispositivo cliente que sea compatible con la configuración Wi-Fi protegida.

Método n.º 1

Utilice este método si el dispositivo cliente tiene un botón Wi-Fi Protected Setup (Configuración Wi-Fi protegida).

Haga clic o pulse el botón 1. Wi-Fi Protected Setup (Configuración Wi-Fi protegida) del dispositivo cliente.

Haga clic en el botón 2. Wi-Fi Protected Setup (Configuración Wi-Fi protegida) que aparece en esta pantalla.

Una vez que el dispositivo cliente se haya configurado, 3. haga clic en OK (Aceptar). A continuación, vuelva al dispositivo cliente o consulte la documentación para obtener más instrucciones.

Método n.º 2

Utilice este método si el dispositivo cliente tiene un número PIN de configuración Wi-Fi protegida.

Introduzca el número PIN en el1. campo que aparece en esta pantalla.

Haga clic en 2. Register (Registro). Una vez que el dispositivo cliente se haya configurado, haga 3.

clic en OK (Aceptar). A continuación, vuelva al dispositivo cliente o consulte la documentación para obtener más instrucciones.

Introduzca el número PIN que aparece en esta pantalla. 1. (También aparece en la etiqueta que hay en la parte inferior del router.)

Una vez que el dispositivo cliente se haya configurado, haga 2. clic en OK (Aceptar). A continuación, vuelva al dispositivo cliente o consulte la documentación para obtener más instrucciones.

En la parte inferior de la pantalla aparecen las opciones Wi-Fi Protected Setup Status (Estado de la configuración Wi-Fi protegida), Nombre de la red (SSID) (Network Name, SSID), Security (Seguridad), Encryption (Encriptación) y Passphrase (Frase de paso).

NOTA: Si el cliente tiene dispositivos que no son

compatibles con la configuración Wi-Fi protegida, anote los parámetros inalámbricos y, a continuación, configure los dispositivos cliente de forma manual.

Wireless > Wireless Security (Inalámbrico > Seguridad inalámbrica)

La pantalla Wireless Security (Seguridad inalámbrica) configura la seguridad de la red inalámbrica. El router admite seis opciones de modo de seguridad inalámbrica: WPA Personal, WPA Enterprise, WPA2 Personal, WPA2 Enterprise, RADIUS y WEP. WPA quiere decir acceso Wi-Fi protegido y es un estándar de seguridad más fiable que la encriptación WEP. WEP significa privacidad equivalente a conexión con cables, mientras que RADIUS significa servicio de usuario de acceso telefónico de autenticación remota. Estas seis opciones se analizan a continuación. Para obtener información detallada sobre la configuración de la seguridad inalámbrica del router, consulte el “Capítulo 2: Seguridad inalámbrica”.

Wireless Security (Seguridad inalámbrica)

Security Mode (Modo de seguridad)

Seleccione el método de seguridad para la red inalámbrica. Si no desea utilizar la seguridad inalámbrica, mantenga el parámetro predeterminado, Disabled (Desactivado).

WPA Personal

NOTA: Si utiliza WPA, recuerde siempre que cada

dispositivo de la red inalámbrica DEBE utilizar el mismo método WPA y la misma clave compartida; de lo contrario, la red no funcionará correctamente.

Método n.º 3

Utilice este método si el dispositivo cliente solicita el número PIN del router.

Router de banda ancha Wireless-N

Security Mode (Modo de seguridad) > WPA Personal

14

Capítulo 3

Configuración avanzada

Passphrase (Frase de paso) Introduzca una frase de paso de

entre 8 y 63 caracteres.

Key Renewal (Renovación de claves) Introduzca un periodo

de renovación de claves que indique al router la frecuencia con que debe cambiar las claves de encriptación. El periodo de renovación de clave de grupo predeterminado es de 3600 segundos.

WPA2 Personal

Security Mode (Modo de seguridad) > WPA2 Personal

Encryption (Encriptación) WPA2 es compatible con dos

métodos de encriptación, TKIP y AES, con claves de encriptación dinámica. Seleccione el tipo de algoritmo, AES o TKIP or AES (TKIP o AES). El algoritmo predeterminado es TKIP or AES (TKIP o AES).

Passphrase (Frase de paso) Introduzca una frase de paso de

entre 8 y 63 caracteres.

Key Renewal (Renovación de claves) Introduzca un periodo

de renovación de claves que indique al router la frecuencia con que debe cambiar las claves de encriptación. El periodo de renovación de clave de grupo predeterminado es de 3600 segundos.

WPA Enterprise

Esta opción permite el uso de WPA junto con un servidor RADIUS. (Sólo se debe utilizar si hay un servidor RADIUS conectado al router.)

Key Renewal (Renovación de claves) Introduzca un periodo

de renovación de claves que indique al router la frecuencia con que debe cambiar las claves de encriptación. El periodo de renovación de claves predeterminado es de 3600 segundos.

WPA2 Enterprise

Esta opción permite el uso de WPA2 junto con un servidor RADIUS. (Sólo se debe utilizar si hay un servidor RADIUS conectado al router.)

Security Mode (Modo de seguridad) > WPA2 Enterprise

Encryption (Encriptación) WPA2 es compatible con dos métodos

de encriptación, TKIP y AES, con claves de encriptación dinámica. Seleccione el tipo de algoritmo, AES o TKIP or AES (TKIP o AES). El algoritmo predeterminado es TKIP or AES (TKIP o AES).

RADIUS Server (Servidor RADIUS) Introduzca la dirección IP

del servidor RADIUS.

RADIUS Port (Puerto RADIUS) Introduzca el número de

puerto del servidor RADIUS. El valor predeterminado es 1812.

Shared Key (Clave compartida) Introduzca la clave

compartida entre el router y el servidor.

Key Renewal (Renovación de claves) Introduzca un periodo

de renovación de claves que indique al router la frecuencia con que debe cambiar las claves de encriptación. El periodo de renovación de claves predeterminado es de 3600 segundos.

RADIUS

Esta opción permite el uso de WEP junto con un servidor RADIUS (Sólo se debe utilizar si hay un servidor RADIUS conectado al router.)

Security Mode (Modo de seguridad) > WPA Enterprise

RADIUS Server (Servidor RADIUS) Introduzca la dirección IP

del servidor RADIUS.

RADIUS Port (Puerto RADIUS) Introduzca el número de

puerto del servidor RADIUS. El valor predeterminado es 1812.

Shared Key (Clave compartida) Introduzca la clave compartida

entre el router y el servidor.

Router de banda ancha Wireless-N

Security Mode (Modo de seguridad) > RADIUS

15

Capítulo 3

IMPORTANTE: Si utiliza encriptación WEP, recuerde

siempre que cada dispositivo de la red inalámbrica DEBE utilizar el mismo método de encriptación WEP y la misma clave de encriptación; de lo contrario, la red inalámbrica no funcionará correctamente.

RADIUS Server (Servidor RADIUS) Introduzca la dirección IP

del servidor RADIUS.

RADIUS Port (Puerto RADIUS) Introduzca el número de

puerto del servidor RADIUS. El valor predeterminado es 1812.

Shared Key (Clave compartida) Introduzca la clave

compartida entre el router y el servidor.

Encryption (Encriptación) Seleccione un nivel de encriptación

WEP, 40/64 bits (10 hex digits) (40/64 bits, 10 dígitos hexadecimales) o 104/128 bits (26 hex digits) (104/128 bits, 26 dígitos hexadecimales). El valor predeterminado es 40 / 64 bits

(10 hex digits) (40 / 64 bits [10 dígitos hexadecimales]).

Passphrase (Frase de paso) Introduzca una frase de paso para

generar las claves WEP de forma automática. A continuación, haga clic en Generate (Generar).

Key 1-4 (Clave 1-4) Si no ha introducido ninguna frase de paso,

introduzca las claves WEP de forma manual.

Configuración avanzada

WEP

WEP es un método de encriptación básico y no es tan seguro como WPA.

Security Mode (Modo de seguridad) > WEP

Encryption (Encriptación) Seleccione un nivel de encriptación

WEP, 40/64 bits (10 hex digits) (40/64 bits, 10 dígitos hexadecimales) o 104/128 bits (26 hex digits) (104/128 bits, 26 dígitos hexadecimales). El valor predeterminado es 40 / 64 bits

(10 hex digits) (40 / 64 bits [10 dígitos hexadecimales]).

Passphrase (Frase de paso) Introduzca una frase de paso para

generar las claves WEP de forma automática. A continuación, haga clic en Generate (Generar).

Key 1-4 (Clave 1-4) Si no ha introducido ninguna frase de paso,

introduzca las claves WEP de forma manual. Haga clic en Save Settings (Guardar parámetros) para guardar

los cambios o en Cancel Changes (Cancelar cambios) para cancelarlos.

Wireless > Wireless MAC Filter (Inalámbrico > Filtro de MAC inalámbrico)

Wireless MAC Filter (Filtro de MAC inalámbrico)

Enabled/Disabled (Activado/Desactivado) Para filtrar los

usuarios por dirección MAC, ya sea para permitir o bloquear el acceso, seleccione Enabled (Activado). Si no desea filtrar los usuarios por dirección MAC, mantenga el valor predeterminado,

Disabled

Access Restriction (Restricción de acceso)

Prevent (Evitar) Selecciónelo para bloquear el acceso

inalámbrico por dirección MAC. Esta opción está activada de forma predeterminada.

Permit (Permitir) Seleccione esta opción para permitir el acceso

inalámbrico por dirección MAC. Esta opción está activada de forma predeterminada.

Lista de filtros de direcciones MAC

Wireless Client List (Lista de clientes inalámbricos) Haga

clic aquí para abrir la pantalla Wireless Client List (Lista de clientes inalámbricos).

(Desactivado).

Wireless > Wireless MAC Filter (Inalámbrico > Filtro de MAC inalámbrico)

Se puede filtrar el acceso inalámbrico mediante el uso de las direcciones MAC de los dispositivos inalámbricos que transmiten en el radio de la red.

Router de banda ancha Wireless-N

Wireless Client List (Lista de clientes inalámbricos)

16

Capítulo 3

Configuración avanzada

Wireless Client List (Lista de clientes inalámbricos)

Esta pantalla muestra los ordenadores y otros dispositivos de la red inalámbrica. La lista se puede ordenar por Client Name (Nombre de cliente), Interface (Interfaz), IP Address (Dirección IP), MAC Address (Dirección MAC) y Status (Estado).

Seleccione Save to MAC Address Filter List (Guardar en la lista de filtros de direcciones MAC) si desea agregar un dispositivo a la lista de filtros de direcciones MAC. A continuación, haga clic en Add (Agregar).

Para recuperar la información más reciente, haga clic en Refresh (Actualizar). Para salir de esta pantalla y volver a la pantalla Wireless MAC Filter (Filtro de MAC inalámbrico), haga clic en Close (Cerrar).

MAC 01-50 Introduzca las direcciones MAC de los dispositivos

cuyo acceso inalámbrico desee bloquear o permitir. Haga clic en Save Settings (Guardar parámetros) para guardar

los cambios o en Cancel Changes (Cancelar cambios) para cancelarlos.

Wireless > Advanced Wireless Settings (Inalámbrico > Parámetros inalámbricos avanzados)

La pantalla Advanced Wireless Settings (Parámetros inalámbricos avanzados) se utiliza para configurar las funciones inalámbricas avanzadas del router Estos parámetros sólo los debe ajustar un administrador experto, ya que unos parámetros incorrectos pueden reducir el rendimiento inalámbrico.

Wireless > Advanced Wireless Settings (Inalámbrico > Parámetros

inalámbricos avanzados)

Advanced Wireless (Parámetros inalámbricos avanzados)

AP Isolation (Aislamiento de PA) Este parámetro aísla entre

sí todos los clientes y dispositivos inalámbricos de la red. Los dispositivos inalámbricos se podrán comunicar con el router, pero no entre ellos. Para utilizar esta función, seleccione Enabled (Activado). El aislamiento de PA está desactivado de forma predeterminada.

Frame Burst (Ráfaga de tramas) Al activar esta opción se

debe conseguir un mayor rendimiento de la red, en función del fabricante de los productos inalámbricos. Para utilizar esta

opción, mantenga el valor predeterminado Enabled (Activado). De lo contrario, seleccione Disabled (Desactivado).

Authentication Type (Tipo de autenticación) El valor

predeterminado está establecido en Auto (Automático), que permite utilizar la autenticación Open System (Sistema abierto) o Shared Key (Clave compartida). Con la autenticación Open System (Sistema abierto), el emisor y el receptor NO utilizan una clave WEP para la autenticación. Con la autenticación Clave compartida, el emisor y el receptor utilizan una clave WEP para la autenticación. Seleccione Shared Key (Clave compartida) para utilizar sólo la autenticación de clave compartida.

Basic Rate (Velocidad básica) Este parámetro en realidad no es

una única velocidad de transmisión, sino una serie de velocidades a las que puede transmitir el router. El router anunciará su velocidad básica a los demás dispositivos inalámbricos de la red para que conozcan las velocidades que se utilizarán. El router también anunciará que seleccionará automáticamente la mejor velocidad para la transmisión. El parámetro predeterminado es Default (Predeterminada), con el que el router puede transmitir a todas las velocidades inalámbricas estándar (1-2 Mbps, 5,5 Mbps, 11 Mbps, 18 Mbps y 24 Mbps). Otras opciones son 1-2 Mbps, para su uso con tecnología inalámbrica antigua y All (Todas), con la que el router puede transmitir a todas las velocidades inalámbricas. La velocidad básica no es la velocidad real de transmisión de datos. Si desea especificar la velocidad de transmisión de datos del router, configure el parámetro Velocidad de transmisión.

Transmission Rate (Velocidad de transmisión) La velocidad

de transmisión de datos se debe establecer según la velocidad

la red inalámbrica. Puede seleccionar un valor entre una

de serie de (Automática) para que el router utilice automáticamente la máxima velocidad de transferencia de datos posible y active la función Auto-Fallback (Reserva automática). Auto-Fallback (Reserva automática) negociará la mejor velocidad de conexión posible entre el router y un cliente inalámbrico. El valor predeterminado es Auto (Automática).

N Transmission Rate (Velocidad de transmisión N) La velocidad

de transmisión de datos se debe establecer según la velocidad de la red Wireless-N. Puede seleccionar un valor entre una serie de velocidades de transmisión o bien seleccionar Auto (Automática) para que el router utilice automáticamente la máxima velocidad de transferencia de datos posible y active la función Auto-Fallback (Reserva automática). Auto-Fallback (Reserva automática) negociará la mejor velocidad de conexión posible entre el router y un cliente inalámbrico. El valor predeterminado es Auto (Automática).

CTS Protection Mode (Modo de protección CTS) El router

utilizará el modo de protección CTS (listo para emitir) de forma automática cuando los productos Wireless-N y Wireless-G experimenten problemas graves y no puedan transmitir al router en un entorno con tráfico 802.11b intenso. Esta función incrementa la capacidad del router para captar todas las transmisiones Wireless-N y Wireless-G, pero reduce el rendimiento en gran medida. El valor predeterminado es

Auto (Automática).

Beacon Interval (Intervalo de baliza) Introduzca un valor

entre 1 y 65.535 milisegundos. Este valor indica el intervalo de frecuencia de la baliza. Una baliza consiste en un paquete difundido por el router para sincronizar la red inalámbrica. El valor predeterminado es 100.

DTIM Interval (Intervalo DTIM) Este valor, entre 1 y 255, indica

el intervalo de mensajes de indicación de tráfico de entrega

velocidades de transmisión o bien seleccionar Auto

Router de banda ancha Wireless-N

17

Capítulo 3

Configuración avanzada

(DTIM). El campo DTIM es un campo de cuenta atrás que informa a los clientes del siguiente intervalo para la recepción de mensajes de difusión y multidifusión. Una vez que el router ha almacenado en el búfer los mensajes de difusión o multidifusión para los clientes asociados, envía el siguiente DTIM con un valor de intervalo DTIM. Sus clientes reciben las balizas y se activan para recibir los mensajes de difusión y multidifusión. El valor predeterminado es 1.

Fragmentation Threshold (Umbral de fragmentación) Este

valor especifica el tamaño máximo de un paquete antes de fragmentar los datos en varios paquetes. Si experimenta una tasa alta de errores de paquete, puede aumentar ligeramente el umbral de fragmentación. Si establece un umbral de fragmentación demasiado bajo, se puede reducir el rendimiento de la red. Sólo se recomiendan reducciones mínimas del valor predeterminado. En la mayoría de los casos, debe permanecer en su valor predeterminado de 2346.

RTS Threshold (Umbral RTS) Si detecta un flujo de datos irregular,

sólo se recomienda realizar una reducción mínima del valor predeterminado, 2347. Si un paquete de red es más pequeño que el tamaño de umbral RTS predefinido, el mecanismo RTS/ CTS no se activará. El router envía tramas de petición de envío (RTS) a una determinada estación de recepción y negocia el envío de una trama de datos. Después de recibir una RTS, la estación inalámbrica responde con una trama de listo para emitir (CTS) para confirmar el inicio de la transmisión. El valor del umbral RTS debe permanecer en su valor predeterminado de 2347.

Haga clic en Save Settings (Guardar parámetros) para guardar los cambios o en Cancel Changes (Cancelar cambios) para cancelarlos.

Security (Seguridad) > Firewall

La pantalla Firewall se utiliza para configurar un firewall que pueda filtrar varios tipos de tráficos no deseados en la red local del router.

externos el acceso a la red. Esta función está seleccionada de forma predeterminada. Desactive la función para permitir las solicitudes de Internet anónimas

Filter Multicast (Filtrar multidifusión) Esta función permite

varias transmisiones simultáneas a receptores específicos. Si activa la multidifusión, el router permitirá que los paquetes de multidifusión IP se reenvíen a los ordenadores adecuados. Seleccione esta función para filtrar multidifusión. Esta función está activada de forma predeterminada.

Filter Internet NAT Redirection (Filtrar redirección NAT de

Internet) Esta función utiliza el reenvío de puertos para bloquear

acceso a los servidores locales desde ordenadores en red

el

Seleccione esta función para filtrar la redirección NAT de

locales. Internet. No está seleccionada de forma predeterminada.

Filter IDENT (Port 113) (Filtrar IDENT, Puerto 113) Esta función

impide que los dispositivos externos a la red local analicen el puerto 113. Esta función está activada de forma predeterminada. Desactive esta función para desactivarla.

.

Web Filter (Filtro web)

Proxy El uso de servidores proxy de WAN puede poner en peligro

la seguridad de la gateway. Con el filtro proxy se desactivará el acceso a los servidores proxy de WAN. Seleccione esta función para activar el filtrado de proxy. Desactive esta función para permitir el acceso de proxy

Java Java es un lenguaje de programación para sitios web.

Si deniega Java, corre el riesgo de no tener acceso a los sitios de Internet creados con este lenguaje de programación. Seleccione esta función para activar el filtrado de Java. Desactive esta función para permitir el uso de Java.

ActiveX ActiveX es un lenguaje de programación para sitios web.

Si deniega ActiveX, corre el riesgo de no tener acceso a los sitios de Internet creados con este lenguaje de programación. Seleccione esta función para activar el filtrado de Active X. Desactive esta función para permitir el uso de Active X.

Cookies Una cookie consiste en datos almacenados en el

ordenador y utilizados en sitios de Internet al interactuar con los mismos. Seleccione esta función para filtrar cookies. Desactive esta función para permitir el uso de cookies.

Haga clic en Save Settings (Guardar parámetros) para guardar los cambios o en Cancel Changes (Cancelar cambios) para cancelarlos.

.

Security (Seguridad) > Firewall

Firewall

SPI Firewall Protection (Protección de firewall SPI) Para utilizar

la protección de firewall, mantenga la selección predeterminada, Enabled (Activada). Para desactivar la protección de firewall, seleccione Disabled (Desactivada).

Internet Filter (Filtros de Internet)

Filter Anonymous Internet Requests (Filtrar solicitudes

anónimas de Internet) Esta función dificulta a los usuarios

Router de banda ancha Wireless-N

Security > VPN Passthrough (Seguridad > Paso a través de VPN)

La pantalla VPN Passthrough (Paso a través de VPN) le permite activar los túneles VPN que utilicen los protocolos IPSec, PPTP o L2TP para pasar a través del firewall del router.

Security > VPN Passthrough (Seguridad > Paso a través de VPN)

18

Capítulo 3

Configuración avanzada

VPN Passthrough (Paso a través de VPN)

IPSec Passthrough (Paso a través de IPSec) La seguridad

de protocolo de Internet (IPSec) es una suite de protocolos utilizados para implantar el intercambio seguro de paquetes en la capa IP. Para permitir que los túneles IPSec pasen a través del router, mantenga el valor predeterminado Enabled (Activado).

PPTP Passthrough (Paso a través de PPTP) El protocolo de

túnel de punto a punto (PPTP) permite establecer túneles para el protocolo de punto a punto (PPP) a través de una red IP. Para permitir que los túneles PPTP pasen a través del router, mantenga el valor predeterminado Enabled (Activado).

L2TP Passthrough (Paso a través de L2TP) El protocolo de túnel

de capa 2 es el método que se utiliza para activar las sesiones de punto a punto a través de Internet en el nivel de capa 2. Para permitir que los túneles L2TP pasen a través del router, mantenga el valor predeterminado Enabled (Activado).

Haga clic en Save Settings (Guardar parámetros) para guardar los cambios o en Cancel Changes (Cancelar cambios) para cancelarlos.

Access Restrictions (Restricciones de acceso) > Acceso a Internet

La pantalla Internet Access (Acceso a Internet) permite bloquear o aceptar determinados tipos de uso y tráfico de Internet, como el acceso a Internet, servicios concretos y sitios web a determinados días y horas.

Internet Access Policy (Directiva de acceso a Internet)

Access Policy (Directiva de acceso) El acceso se puede

administrar mediante una directiva. Utilice los parámetros de esta pantalla para establecer una directiva de acceso (después de hacer clic en Save Settings [Guardar parámetros]). Al seleccionar una directiva en el menú desplegable se mostrarán los parámetros de la misma. Para eliminar una directiva, seleccione su número y haga clic en el botón Delete This Policy (Eliminar esta directiva). Para ver todas las directivas, haga clic en el botón Summary (Resumen).

Resumen

Las directivas se enumeran con la siguiente información: No. (N.º), Policy Name (Nombre de directiva), Access (Acceso), Days (Días), Time (Hora) y estado (Enabled [Activada]). Para activar una directiva, seleccione Enabled (Activada). Para eliminar una directiva, haga clic en Delete (Eliminar). Haga clic en Save Settings (Guardar parámetros) para aplicar los cambios o en Cancel Changes (Cancelar cambios) para cancelarlos. Para volver a la pantalla Internet Access Policy (Directiva de acceso a Internet), haga clic en Close (Cerrar).

Access Restrictions (Restricciones de acceso) > Acceso a Internet

Router de banda ancha Wireless-N

Resumen

Status (Estado) De forma predeterminada, las directivas

están desactivadas. Para activar una directiva, seleccione su número en el menú desplegable, y seleccione Enabled (Activada).

Para crear una directiva, siga los pasos del 1 al 11. Repita estos pasos para crear directivas adicionales de una en una.

Seleccione un número en el menú desplegable 1. Access Policy (Directiva de acceso).

Introduzca un nombre de directiva en el campo 2. proporcionado.

Para activar esta directiva, seleccione 3. Enabled (Activada). Haga clic en 4. Edit List (Editar lista) para seleccionar los PC a

los que afectará esta directiva. Aparecerá la pantalla List of PCs (Lista de PC). Puede seleccionar un PC por dirección MAC o por dirección IP. También puede introducir un intervalo de direcciones IP si desea que esta directiva afecte a un grupo de PC. Tras efectuar los cambios, haga clic en Save Settings (Guardar parámetros) para aplicar los cambios, o bien en Cancel Changes (Cancelar cambios) para cancelarlos. A continuación, haga clic en Close (Cerrar).

19

Capítulo 3

List of PCs (Lista de PC)

Seleccione la opción correspondiente, 5. Deny (Denegar) o Allow (Permitir), en función de si desea bloquear o permitir el acceso a Internet de los PC enumerados en la pantalla List of PCs (Lista de PC).

Decida los días y las horas en que desea que se aplique esta 6. directiva. Seleccione cada día en que se aplicará la directiva o seleccione Everyday (Todos los días). A continuación, introduzca un intervalo de horas y minutos durante los que se aplicará la directiva o seleccione 24 Hours (24 horas).

Es posible bloquear sitios web con direcciones URL 7. específicas. Introduzca cada URL en un campo URL distinto.

También puede bloquear sitios web mediante palabras 8. clave específicas. Introduzca cada palabra clave en un campo Keyword (Palabra clave) distinto.

Puede filtrar el acceso a diferentes servicios a los que se 9. puede acceder a través de Internet, como FTP o Telnet. (Puede bloquear hasta tres aplicaciones por directiva.)

En la lista Applications (Aplicaciones), seleccione la aplicación que desee bloquear. A continuación, haga clic

el botón >> para mover el elemento a la lista Blocked

en List (Lista de bloqueos). Para eliminar una aplicación de la lista de bloqueos (Blocked List), selecciónela y haga clic en el botón <<.

Si la aplicación que desea bloquear no aparece o desea 10. editar los parámetros de un servicio, introduzca el nombre de la aplicación en el campo Application Name (Nombre de aplicación). Introduzca su intervalo en los campos Port Range (Intervalo de puertos). Seleccione su protocolo en el menú desplegable Protocol (Protocolo). A continuación, haga clic en Add (Agregar).

Para modificar un servicio, selecciónelo en la lista de aplicaciones. Cambie el nombre, el intervalo de puertos o el parámetro de protocolo. A continuación, haga clic en Modify (Modificar).

Para eliminar un servicio, selecciónelo en la lista Application (Aplicaciones). A continuación, haga clic en Delete (Eliminar).

Haga clic en 11. Save Settings (Guardar parámetros) para guardar los parámetros de la directiva. Para cancelar los parámetros de la directiva, haga clic en Cancel Changes (Cancelar cambios).

Configuración avanzada

Applications and Gaming > Single Port Forwarding (Aplicaciones y juegos > Reenvío de puerto único)

La pantalla Single Port Forwarding (Reenvío de puerto único) le permite personalizar los servicios de puertos para aplicaciones comunes en esta pantalla.

Cuando los usuarios envían estos tipos de solicitudes a la red a través de Internet, el router las reenvía a los servidores apropiados (ordenadores). Antes de utilizar el reenvío, debe asignar direcciones IP estáticas a los servidores designados (utilice la función DHCP Reservation [Reserva DHCP] de la pantalla Basic Setup [Configuración básica]).

Applications and Gaming > Single Port Forwarding

(Aplicaciones y juegos > Reenvío de puerto único)

Single Port Forwarding (Reenvío de puerto único)

Para las cinco primeras entradas hay aplicaciones comunes disponibles. Seleccione la aplicación adecuada. A continuación, introduzca la dirección IP del servidor que debe recibir estas solicitudes. Seleccione Enabled (Activada) para activar esta entrada.

Para aplicaciones adicionales, rellene los siguientes campos:

Application Name (Nombre de aplicación) Introduzca en

este campo el nombre que desea asignar a la aplicación. Cada nombre puede tener hasta 12 caracteres.

External Port (Puerto externo) Introduzca el número de

puerto externo que utiliza el servidor o la aplicación de Internet. Consulte la documentación de la aplicación de Internet para obtener más información.

Internal Port (Puerto interno) Introduzca el número de puerto

interno que utiliza el servidor o la aplicación de Internet. Consulte la documentación de la aplicación de Internet para obtener más información.

Protocol (Protocolo) Introduzca el protocolo que se utilizará

para esta aplicación, TCP, UDP o Both (Ambos).

Router de banda ancha Wireless-N

20

Capítulo 3

Configuración avanzada

To IP Address (Dirección IP) Para cada aplicación, introduzca la

dirección IP del PC que debe recibir las solicitudes. Si ha asignado una dirección IP estática al ordenador, puede buscar su dirección IP estática haciendo clic en la opción DHCP Reservation (Reserva DHCP) de la pantalla Basic Setup (Configuración básica).

Enabled (Activado) Para cada aplicación, seleccione

Enabled (Activado) para activar el reenvío de puertos.

Haga clic en Save Settings (Guardar parámetros) para guardar los cambios o en Cancel Changes (Cancelar cambios) para cancelarlos.

Applications and Gaming > Port Range Forwarding (Aplicaciones y juegos > Reenvío de intervalos de puertos)

La pantalla Port Range Forwarding (Reenvío de intervalos de puertos) permite configurar servicios públicos en la red, como servidores web, servidores FTP, servidores de correo electrónico u otras aplicaciones especializadas de Internet. (Las aplicaciones de Internet especializadas son aquéllas que utilizan el acceso a Internet para realizar funciones como videoconferencias o juegos en línea. Puede que algunas aplicaciones de Internet no requieran ningún reenvío).

Cuando los usuarios envían estos tipos de solicitudes a la red a través de Internet, el router las reenvía a los servidores apropiados (ordenadores). Antes de utilizar el reenvío, debe asignar direcciones IP estáticas a los servidores designados (utilice la función DHCP Reservation [Reserva DHCP] de la pantalla Basic Setup [Configuración básica]).

Si tiene que reenviar todos los puertos a un ordenador, haga clic en la ficha DMZ.

Start ~ End Port (Puerto inicial ~ final) Introduzca el número

intervalo de puertos utilizados por el servidor o las aplicaciones

o de Internet. Consulte la documentación de la aplicación de Internet para obtener más información.

Protocol (Protocolo) Introduzca el protocolo que se utilizará

para esta aplicación, TCP, UDP o Both (Ambos).

To IP Address (Dirección IP) Introduzca para cada aplicación la

dirección IP del ordenador que ejecuta la aplicación específica. Si ha asignado una dirección IP estática al ordenador, puede buscar su dirección IP estática haciendo clic en la opción

DHCP Reservation (Reserva DHCP) de la pantalla Basic Setup (Configuración básica).

Enabled (Activado) Seleccione Enabled (Activado) para

activar el reenvío de puertos para las aplicaciones que haya definido.

Haga clic en Save Settings (Guardar parámetros) para guardar los cambios o en Cancel Changes (Cancelar cambios) para cancelarlos.

Applications & Gaming > Port Range Triggering (Aplicaciones y juegos > Desencadenado de intervalos de puertos)

La pantalla Port Range Triggering (Desencadenado de intervalos de puertos) permite que el router controle los datos salientes de números de puerto específicos. El router recuerda la dirección IP del ordenador que envía los datos coincidentes, de forma que, cuando los datos solicitados circulen a través del router, se dirijan al ordenador correspondiente mediante la dirección IP y las reglas de asignación de puertos.

Applications and Gaming > Port Range Forwarding (Aplicaciones y

juegos > Reenvío de intervalos de puertos)

Port Range Forwarding (Reenvío de intervalos de puertos)

Para reenviar un puerto, introduzca la información solicitada en cada línea, según los criterios pertinentes.

Application Name (Nombre de aplicación) Introduzca en

este campo el nombre que desea asignar a la aplicación. Cada nombre puede tener hasta 12 caracteres.

Router de banda ancha Wireless-N

Applications and Gaming > Port Range Triggering (Aplicaciones y

juegos > Desencadenado de intervalos de puertos)

Port Range Triggering (Desencadenado de intervalos de puertos)

Application Name (Nombre de aplicación) Introduzca el

nombre de aplicación del desencadenador.

Triggered Range (Intervalo desencadenado) Introduzca para

cada aplicación los números inicial y final del intervalo de números de puertos desencadenados. Consulte en la documentación de la aplicación de Internet los números de puerto necesarios.

21

Capítulo 3

Forwarded Range (Intervalo reenviado) Introduzca para cada

aplicación los números inicial y final del intervalo de números de puertos reenviados. Consulte en la documentación de la aplicación de Internet los números de puerto necesarios.

Enabled (Activado) Seleccione Enabled (Activado) para

activar el desencadenado de puertos para las aplicaciones que haya definido.

Haga clic en Save Settings (Guardar parámetros) para guardar los cambios o en Cancel Changes (Cancelar cambios) para cancelarlos.

Configuración avanzada

Applications and Gaming (Aplicaciones y juegos) > DMZ

La función DMZ permite exponer a un ordenador de red a Internet para el uso de un servicio especial, como juegos por Internet y videoconferencias. La asignación de DMZ reenvía todos los puertos a un PC al mismo tiempo. La función de reenvío de intervalos de puertos es más segura porque sólo abre los puertos que usted desee, mientras que la asignación de DMZ abre todos los puertos de un ordenador, exponiéndolo a Internet.

Applications and Gaming (Aplicaciones y juegos) > DMZ

DMZ > DHCP Client Table (Tabla de clientes DHCP)

DHCP Clients Table (Tabla de clientes DHCP)

La tabla de clientes DHCP indica los ordenadores y otros dispositivos a los que el router ha asignado direcciones IP. La lista se puede ordenar por Nombre de cliente (Client Name), Interfaz (Interface), Dirección IP (IP Address), Dirección MAC (MAC Address) y Hora de caducidad (Expired Time) (tiempo que le queda a la dirección IP actual). Para seleccionar un cliente DHCP, haga clic en Select (Seleccionar). Para recuperar la información más-reciente, haga clic en Refresh (Actualizar). Para salir de esta pantalla y volver a la pantalla DMZ, haga clic en Close (Cerrar).

Haga clic en Save Settings (Guardar parámetros) para guardar los cambios o en Cancel Changes (Cancelar cambios) para cancelarlos.

Applications and Gaming (Aplicaciones y juegos) > QoS

La calidad de servicio (QoS) garantiza un servicio óptimo para tipos de tráfico de red de alta prioridad, que pueden consistir en aplicaciones en tiempo real y muy exigentes, como las videoconferencias.

DMZ

Cualquier PC cuyo puerto se reenvíe debe tener la función de cliente DHCP desactivada y debe tener asignada una nueva dirección IP estática, ya que su dirección IP puede cambiar al utilizar la función DHCP.

Enabled/Disabled (Activado/Desactivado) Para desactivar la

asignación de DMZ, seleccione Disabled (Desactivado). Para exponer un PC, seleccione Enabled (Activado). A continuación, configure los siguientes parámetros:

Source IP Address (Dirección IP de origen) Si desea que el

origen sea una dirección IP, seleccione Any IP Address (Cualquier dirección IP). Si desea especificar como origen designado una dirección IP o un intervalo de direcciones IP, seleccione y complete los campos de intervalos de direcciones IP.

Destination (Destino) Si desea especificar la asignación de

DMZ por dirección IP, seleccione IP Address (Dirección IP) y rellene el campo correspondiente con la dirección IP. Si desea especificar la asignación de DMZ por dirección MAC, seleccione MAC Address (Dirección MAC) y rellene el campo correspondiente con la dirección MAC. Para recuperar esta información, haga clic en DHCP Client Table (Tabla de clientes DHCP).

Router de banda ancha Wireless-N

Applications and Gaming (Aplicaciones y juegos) > QoS

QoS (calidad de servicio)

Wireless (Inalámbrico)

Puede configurar los parámetros No Acknowledgement (Sin confirmación) y de compatibilidad en esta sección.

WMM Support (Compatibilidad con WMM) Si tiene otros

dispositivos compatibles con Wi-Fi Multimedia (WMM) en la red, mantenga el valor predeterminado Enabled (Activado). De lo contrario, seleccione Disabled (Desactivado).

22

Capítulo 3

Configuración avanzada

No Acknowledgement (Sin confirmación) Si desea desactivar

la función de confirmación del router para que no envíe los datos de nuevo si se produce un error, seleccione Enabled (Activado). De lo contrario, mantenga el valor predeterminado Disabled (Desactivado).

Internet Access Priority (Prioridad de acceso a Internet)

En esta sección, puede establecer la prioridad de ancho de banda para varias aplicaciones y dispositivos. Hay cuatro niveles de prioridad: High (Alta), Medium (Media), Normal o Low (Baja). Al establecer la prioridad, no configure todas las aplicaciones con prioridad Alta porque esto rechazará la asignación del ancho de banda disponible. Si desea seleccionar un ancho de banda por debajo de lo normal, seleccione Baja. En función de la aplicación, es posible que sean necesarios varios intentos para establecer la prioridad de ancho de banda adecuada.

Enabled/Disabled (Activado/Desactivado) Para utilizar

las directivas de QoS que ha configurado, mantenga el valor predeterminado, Enabled (Activado). De lo contrario, seleccione Disabled (Desactivado).

Category (Categoría)

Hay cuatro categorías disponibles. Seleccione una de las siguientes: Applications (Aplicaciones), Online Games (Juegos en línea), MAC Address (Dirección MAC), Ethernet Port (Puerto Ethernet) o Voice Device (Dispositivo de voz). Siga las instrucciones para realizar la selección.

Seleccione el protocolo TCP o UDP o seleccione Both (Ambos).

Priority (Prioridad) Seleccione la prioridad adecuada: High

(Alta), Medium (Recommend) (Media [recomendada]), Normal o Low (Baja).

Haga clic en Add (Agregar) para guardar los cambios. La nueva entrada aparecerá en la lista Summary (Resumen).

Online Games (Juegos en línea)

QoS > Online Games (Juegos en línea)

Games (Juegos) Seleccione el juego adecuado. Priority (Prioridad) Seleccione la prioridad adecuada: High

(Alta), Medium (Recommend) (Media [recomendada]), Normal o Low (Baja).

Haga clic en Add (Agregar) para guardar los cambios. La nueva entrada aparecerá en la lista Summary (Resumen).

MAC Address (Dirección MAC)

Applications (Aplicaciones)

Applications (Aplicaciones) Seleccione la aplicación adecuada.

Si selecciona Add a New Application (Agregar una nueva aplicación), siga las instrucciones que se indican en esta opción.

Priority (Prioridad) Seleccione la prioridad adecuada:

High (Alta), Medium (Media), Normal o Low (Baja).

Haga clic en Add (Agregar) para guardar los cambios. La nueva entrada aparecerá en la lista Summary (Resumen).

Add a New Application (Agregar una nueva aplicación)

QoS > Add a New Application (Agregar una nueva aplicación)

Enter a Name (Introducir un nombre) Introduzca un nombre

para indicar el nombre de la entrada.

Port Range (Intervalo de puertos) Introduzca el intervalo de

puertos que va a utilizar la aplicación. Por ejemplo, si desea asignar un ancho de banda al servidor FTP, puede introducir 21-21. Si necesita servicios para una aplicación que utiliza un ancho de banda de 1000 a 1250, debe introducir 1000-1250 como parámetro. Puede definir hasta tres intervalos para esta asignación de ancho de banda. Los números de puerto pueden oscilar entre 1 y 65535. Consulte la documentación de las aplicaciones para obtener más información sobre los puertos de servicio utilizados.

QoS > MAC Address (Dirección MAC)

Enter a Name (Introducir un nombre) Introduzca un nombre

para el dispositivo.

MAC Address (Dirección MAC) Introduzca la dirección MAC del

dispositivo.

Priority (Prioridad) Seleccione la prioridad adecuada: High

(Alta), Medium (Recommend) (Media [recomendada]), Normal o Low (Baja).

Haga clic en Add (Agregar) para guardar los cambios. La nueva entrada aparecerá en la lista Summary (Resumen).

Ethernet Port (Puerto Ethernet)

QoS > Ethernet Port (Puerto Ethernet)

Ethernet Seleccione el puerto Ethernet apropiado. Priority (Prioridad) Seleccione la prioridad adecuada: High

(Alta), Medium (Recommend) (Media [recomendada]), Normal o Low (Baja).

Haga clic en Add (Agregar) para guardar los cambios. La nueva entrada aparecerá en la lista Summary (Resumen).

Router de banda ancha Wireless-N

23

Capítulo 3

Configuración avanzada

Voice Device (Dispositivo de voz)

QoS > Voice Device (Dispositivo de voz)

Enter a Name (Introducir un nombre) Introduzca un nombre

para el dispositivo de voz.

MAC Address (Dirección MAC) Introduzca la dirección MAC

del dispositivo de voz.

Priority (Prioridad) Seleccione la prioridad adecuada:

High (Recommend) (Alta [recomendada]), Medium (Media), Normal o Low (Baja).

Haga clic en Add (Agregar) para guardar los cambios. La nueva entrada aparecerá en la lista Summary (Resumen).

Summary (Resumen)

Esta opción muestra las entradas de QoS que ha creado para las aplicaciones y los dispositivos.

Priority (Prioridad) Esta columna muestra la prioridad de ancho

de banda High (Alta), Medium (Media), Normal o Low (Baja).

Name (Nombre) Esta columna muestra el nombre de la

aplicación, del dispositivo o del puerto.

Information (Información) Esta columna muestra el intervalo

de puertos o la dirección MAC que haya introducido para la entrada. Si se ha seleccionado una aplicación o juego preconfigurados, no aparecerá ninguna entrada válida en esta sección.

Remove (Eliminar) Haga clic en este botón para eliminar una entrada. Edit (Editar) Haga clic en este botón para realizar cambios.

Haga clic en Save Settings (Guardar parámetros) para guardar los cambios o en Cancel Changes (Cancelar cambios) para cancelarlos.

Administration > Management (Administración > Gestión)

La pantalla Administration > Management (Administración > Gestión) permite que el administrador de la red administre funciones específicas del router para el acceso y la seguridad.

Management (Gestión)

Acceso al router

Para garantizar la seguridad del router, se le solicitará la contraseña cuando acceda a la utilidad basada en web del router. La contraseña predeterminada es admin.

Router Password (Contraseña del router) Introduzca una

nueva contraseña para el router.

Re-enter to confirm (Confirmar contraseña) Vuelva a

introducir la contraseña para confirmarla.

Web Access (Acceso web)

Web Utility Access (Acceso a la utilidad web) HTTP (protocolo de

transferencia de hipertexto) es el protocolo de comunicaciones utilizado para conectarse a los servidores de la web. HTTPS utiliza SSL (capa de socket seguro) para encriptar los datos transmitidos para una mayor seguridad. Seleccione HTTP o HTTPS. HTTP es el protocolo predeterminado.

Web Utility Access via Wireless (Acceso a la utilidad web de

forma inalámbrica) Si utiliza el router en un dominio público donde se concede acceso inalámbrico a los invitados, puede desactivar el acceso inalámbrico a la utilidad basada en web del router. Si desactiva el parámetro, sólo podrá acceder a la utilidad mediante una conexión con cables. Seleccione Enabled (Activado) para permitir el acceso inalámbrico a la utilidad, o bien seleccione Disabled (Desactivado) para bloquear el acceso inalámbrico a la utilidad.

Remote Access (Acceso remoto)

Remote Management (Administración remota) Para permitir

el acceso remoto al router desde fuera de la red local, seleccione Enabled (Activado). De lo contrario, mantenga el valor predeterminado Disabled (Desactivado).

Web Utility Access (Acceso a la utilidad web) HTTP

(protocolo de transferencia de hipertexto) es el protocolo de comunicaciones utilizado para conectarse a los servidores de la web. HTTPS utiliza SSL (capa de socket seguro) para encriptar los datos transmitidos para una mayor seguridad. Seleccione

HTTP o HTTPS. HTTP es el protocolo predeterminado.

Remote Upgrade (Actualización remota) Si desea poder

actualizar el router de forma remota, desde fuera de la red local, seleccione Enabled (Activado). (También debe tener activada la función de administración remota.) De lo contrario, mantenga el parámetro predeterminado Disabled (Desactivado).

Allow Remote IP Address (Permitir Dirección IP remota)

Si desea poder acceder al router desde cualquier dirección IP externa, seleccione Any IP Address (Cualquier dirección IP). Si desea especificar una dirección IP externa o un intervalo de direcciones IP, seleccione la segunda opción y rellene los campos correspondientes.

Remote Management Port (Puerto de administración remota)

Introduzca el número de puerto que se abrirá al acceso exterior.

Administration > Management (Administración > Gestión)

Router de banda ancha Wireless-N

NOTA: Cuando se encuentre en una ubicación remota

y desee administrar el router, escriba

http://<Internet_IP_address>:port o https://<Internet_IP_address>:port, dependiendo

de si utiliza HTTP o HTTPS. Introduzca la dirección IP específica del router en lugar de <dirección_IP_de_Internet> e introduzca el número de puerto de administración remota en lugar de la palabra puerto.

24

Capítulo 3

UPnP

El sistema Universal Plug and Play (UPnP) permite a Windows Me y XP configurar automáticamente el router para varias aplicaciones de Internet, como juegos y videoconferencias.

Upnp Si desea utilizar UPnP, mantenga el parámetro

predeterminado, Enabled (Activado). De lo contrario, seleccione Disabled (Desactivado).

Allow Users to Configure (Permitir a los usuarios la

configuración) Mantenga el parámetro predeterminado Enabled (Activado) si desea poder efectuar cambios manuales en el router mientras se utiliza la función UPnP. De lo contrario, seleccione Disabled (Desactivado).

Allow Users to Disable Internet Access (Permitir que los

usuarios desactiven el acceso a Internet) Seleccione Enabled (Activado), si desea poder prohibir una o todas las conexiones de Internet. De lo contrario, mantenga el valor predeterminado, Disabled (Desactivado).

Backup and Restore (Copia de seguridad y restauración)

Backup Configurations (Copia de seguridad de la configuración)

Para realizar una copia de seguridad de la configuración del router, haga clic en este botón y siga las instrucciones de la pantalla.

Restore Configurations (Restauración de la configuración)

Para restaurar la configuración del router, haga clic en este botón y siga las instrucciones de la pantalla. (Antes debe haber realizado una copia de seguridad de la configuración del router.)

Haga clic en Save Settings (Guardar parámetros) para guardar los cambios o en Cancel Changes (Cancelar cambios) para cancelarlos.

Configuración avanzada

Administración > Registro > Ver registro

Log (Registro)

Type • (Tipo) Seleccione Incoming Log (Registro de entrada),

Outgoing Log (Registro de salida), Security Log (Registro de seguridad) o DHCP Client Log (Registro de clientes DHCP).

<Type> Log • (Registro de <tipo>) El registro de entrada

muestra un registro temporal de las direcciones IP de origen y los números de puerto de destino del tráfico de Internet entrante. El registro de salida muestra un registro temporal de las direcciones IP de LAN, las direcciones URL o IP de destino y los números de servicio o puerto del tráfico de Internet saliente. El registro de seguridad mostrará los datos de inicio de sesión de la utilidad basada en web. El registro de clientes DHCP mostrará la información de estado del servidor DHCP de LAN.

Haga clic en el botón Save the Log (Guardar el registro) para guardar esta información en un archivo del disco duro del PC. Haga clic en Refresh (Actualizar) para actualizar el registro. Haga clic en el botón Clear (Borrar) para borrar toda la información que se muestra.

Haga clic en Save Settings (Guardar parámetros) para guardar los cambios o en Cancel Changes (Cancelar cambios) para cancelarlos.

Administration > Log (Administración > Registro)

El router puede mantener registros de todo el tráfico de la conexión a Internet.

Administration > Log (Administración > Registro)

Registro

Log (Registro) Para desactivar la función Log (Registro),

seleccione Disabled (Desactivado). Para controlar el tráfico entre la red e Internet, mantenga el valor predeterminado Enabled (Activado). Cuando los registros están activados, puede optar por ver los registros temporales.

View Log (Ver registro) Para ver los registros, haga clic en

View Log (Ver registro).

Administration > Diagnostics (Administración > Diagnóstico)

Las pruebas de diagnóstico (ping y traceroute) permiten comprobar las conexiones de los dispositivos de red, incluida la conexión a Internet. Esta pantalla le permite reiniciar el router.

Administration > Diagnostics (Administración > Diagnóstico)

Router de banda ancha Wireless-N

25

Capítulo 3

Reboot (Reinicio)

Reboot (Reinicio) Haga clic en Reboot (Reinicio) para

reiniciar el router.

Diagnostics (Diagnóstico)

Ping Test (Prueba de ping)

La prueba de ping comprueba el estado de una conexión.

IP or URL Address (Dirección IP o URL) Introduzca la

dirección del ordenador cuya conexión desea probar.

Packet Size (Tamaño de paquete) Introduzca el tamaño de

paquete que desea utilizar. El tamaño predeterminado es

32 bytes.

Times to Ping (Número de pings) Inténtelo todas las veces

que desee realizar la prueba.

Start to Ping (Iniciar ping) Para realizar la prueba, haga clic

en este botón. La pantalla Ping Test (Prueba de Ping) mostrará si la prueba se ha realizado con éxito. Haga clic en el botón Close (Cerrar) para volver a la pantalla Diagnostics (Diagnóstico).

Configuración avanzada

Diagnóstico > Traceroute

Administration > Factory Defaults (Administración > Parámetros predeterminados de fábrica)

La pantalla Administration > Factory Defaults (Administración > Parámetros predeterminados de fábrica) permite restaurar la configuración del router con los parámetros predeterminados de fábrica.

Diagnóstico > Ping

Prueba de Traceroute

La prueba de traceroute comprueba el rendimiento de una conexión.

IP or URL Address (Dirección IP o URL) Introduzca la

dirección del ordenador cuya conexión desea probar.

Start to Traceroute (Iniciar traceroute) Para realizar la prueba,

haga clic en este botón. La pantalla Traceroute Test (Prueba de traceroute) mostrará si la prueba se ha realizado con éxito. Haga clic en el botón Close (Cerrar) para volver a la pantalla Diagnostics (Diagnóstico).

Administration > Factory Defaults (Administración > Parámetros

predeterminados de fábrica)

NOTA: No restaure los parámetros de fábrica a menos

que tenga dificultades con el router y haya agotado todas las demás medidas de solución de problemas. Cuando se hayan restaurado los parámetros del router, tendrá que volver a introducir todos los parámetros de configuración.

Factory Defaults (Parámetros predeterminados de fábrica)

Restore All Settings (Restaurar todos los parámetros)

Para restablecer los parámetros del router en los valores predeterminados, haga clic en este botón y siga las instrucciones que aparecen en pantalla. Los parámetros que haya guardado se perderán al restaurar los parámetros predeterminados.

Router de banda ancha Wireless-N

26

Capítulo 3

Administration > Firmware Upgrade (Administración > Actualización del firmware)

La pantalla Firmware Upgrade (Actualización del firmware) permite actualizar el firmware del router. No actualice el firmware a menos que tenga problemas con el router o desee utilizar una función del nuevo router.

Configuración avanzada

Status (Estado) > Router

Administration > Firmware Upgrade (Administración >

NOTA: Es posible que el router pierda los parámetros

que haya personalizado. Antes de actualizar el firmware, anote todos los parámetros personalizados. Después de actualizar el firmware, tendrá que volver

-a introducir los parámetros de configuración.

Actualización del firmware)

Firmware Upgrade (Actualización del firmware)

Antes de actualizar el firmware, descargue el archivo de actualización del firmware del router desde el sitio web de Linksys, www.linksys.es. A continuación, extraiga el archivo.

Please select a file to upgrade the firmware (Seleccione

un archivo para actualizar el firmware) Haga clic en Browse (Examinar) para seleccionar el archivo de actualización de firmware que ha extraído.

Start to Upgrade (Iniciar actualización) Después de

seleccionar el archivo adecuado, haga clic en este botón y

iga las instrucciones de la pantalla.

s

Status (Estado) > Router

La pantalla Router muestra información acerca del router y sus parámetros actuales.

Router Information (Información del router)

Firmware Version (Versión del firmware) Es el número de

versión del firmware actual del router.

Firmware Verification (Verificación del firmware) Muestra el

valor MD5 generado durante la compilación.

Current Time (Hora actual) Muestra la hora configurada en

el router.

Internet MAC Address (Dirección MAC de Internet) Se trata

de la dirección MAC del router tal como la ve el ISP.

Host Name (Nombre de host) Si lo requiere el ISP, se

introduce en la pantalla Basic Setup (Configuración básica).

Domain Name (Nombre de dominio) Si lo requiere el ISP,

se introduce en la pantalla Basic Setup (Configuración básica).

Internet Connection (Conexión a Internet)

Esta sección muestra la información de red actual almacenada en el router. La información varía en función del tipo de conexión a Internet seleccionada en la pantalla Basic Setup (Configuración básica).

Haga clic en el botón Refresh (Actualizar) para actualizar la información de la pantalla.

Status > Local Network (Estado > Red local)

La pantalla Local Network (Red local) muestra información sobre la red con cables local.

Router de banda ancha Wireless-N

27

Capítulo 3

Status > Local Network (Estado > Red local)

Local Network (Red local)

Local MAC Address (Dirección MAC local) Indica la dirección

MAC de la interfaz con cables local del router.

Router IP Address (Dirección IP del router) Indica la dirección

IP del router tal como aparece en la red local.

Subnet Mask (Máscara de subred) Indica la máscara de

subred del router.

DHCP Server (Servidor DHCP)

DHCP Server (Servidor DHCP) En este campo se muestra

el estado del funcionamiento del servidor DHCP del router.

Start IP Address (Dirección IP inicial) Indica la dirección IP

inicial del intervalo de direcciones IP que utilizan los dispositivos de la red local.

End IP Address (Dirección IP final) Indica la dirección IP final

del intervalo de direcciones IP que utilizan los dispositivos de la red local.

DHCP Clients Table (Tabla de clientes DHCP) Haga clic en este

botón para ver la lista de ordenadores que están utilizando el router como servidor DHCP.

Configuración avanzada

Status > Wireless Network (Estado > Red inalámbrica)

La pantalla Wireless Network (Red inalámbrica) muestra información sobre la red inalámbrica.

Status > Wireless (Estado > Inalámbrica)

Wireless Network (Red inalámbrica)

MAC Address (Dirección MAC) Indica la dirección MAC de la

interfaz inalámbrica local del router.

Mode (Modo) Aquí se indica el modo inalámbrico que utiliza

la red.

Network Name (SSID) (Nombre de la red [SSID]) Aquí se

indica el nombre de la red inalámbrica, también llamado SSID.

Channel Width (Ancho de canal) Se muestra el parámetro

de banda de radio seleccionado en la pantalla Basic Wireless Settings (Parámetros inalámbricos básicos).

Channel (Canal) Se muestra el parámetro de canal seleccionado

en la pantalla Basic Wireless Settings (Parámetros inalámbricos básicos).

Security (Seguridad) Se muestra el método de seguridad

inalámbrica utilizado por el router.

SSID Broadcast (Difusión de SSID) Estado de la función SSID

Broadcast (Difusión SSID).

DHCP Clients Table (Tabla de clientes DHCP)

La tabla de clientes DHCP indica los ordenadores y otros dispositivos a los que el router ha asignado direcciones IP. La lista se puede ordenar por Nombre de cliente (Client Name), Interfaz (Interface), Dirección IP (IP Address0), Dirección MAC (MAC Address) y Hora de caducidad (Expired Time) (tiempo que le queda a la dirección IP actual). Para eliminar un cliente DHCP, haga clic en Delete (Eliminar). Para recuperar

información más reciente, haga clic en Refresh (Actualizar).

la Para salir de esta pantalla y volver a la pantalla Local Network (Red local), haga clic en Close (Cerrar).

Router de banda ancha Wireless-N

28

Apéndice A

Resolución de problemas

Apéndice A: Resolución de problemas

Su ordenador no puede conectarse a Internet.

Siga las siguientes instrucciones hasta que el ordenador pueda conectarse a Internet:

Asegúrese de que el router está encendido. La luz de • alimentación debe estar encendida en verde y no debe parpadear.

Si la luz de alimentación parpadea, apague todos • los dispositivos de red, incluidos módem, router y ordenadores. A continuación, encienda cada dispositivo en el siguiente orden:

Módem por cable o DSL1.

Router2.

Ordenador3.

Compruebe las conexiones de los cables. El ordenador • debe estar conectado a uno de los puertos numerados del 1 al 4 del router y el módem al puerto de Internet del router.

El módem no dispone de puerto Ethernet.

El módem es un módem de acceso telefónico para el servicio de acceso telefónico tradicional. Para utilizar este router, necesita un módem por cable/DSL y una conexión a Internet de alta velocidad.

No puede utilizar el servicio DSL para conectarse de forma manual a Internet.

Una vez que haya instalado el router, se conectará automáticamente al proveedor de servicios de Internet (ISP), para que no tenga que volver a conectarse de forma manual.

Al hacer doble clic en el explorador web, se le solicitará un nombre de usuario y una contraseña. Si desea evitar esta solicitud, siga las siguientes instrucciones.

Abra el explorador web y complete los siguientes pasos (estos pasos son específicos para Internet Explorer, pero son similares para otros exploradores):

Seleccione 1. Herramientas > Opciones de Internet. Haga clic en la ficha 2. Conexiones. Seleccione 3. No marcar nunca una conexión. Haga clic en 4. Aceptar.

El router no tiene un puerto coaxial para la conexión por cable.

El router no es un sustituto del módem. El módem por cable sigue siendo necesario para utilizar el router. Conecte la conexión por cable al módem por cable y, a continuación, inserte el CD de configuración en el ordenador. Haga clic en Setup (Configuración) y siga las instrucciones que aparecen en- pantalla.

El ordenador no puede conectarse a la red de forma inalámbrica.

Asegúrese de que el nombre de la red inalámbrica o SSID es el mismo en el ordenador y en el router. Si ha activado la seguridad inalámbrica, asegúrese de que el ordenador y el router utilizan el mismo método de seguridad y la misma clave.

Debe modicar los parámetros del router.

Abra el explorador web (por ejemplo, Internet Explorer o

e introduzca la dirección IP del router en el campo de

Firefox) dirección (la dirección IP predeterminada es 192.168.1.1). Cuando se le solicite, escriba la contraseña del router (la contraseña predeterminada es admin). Haga clic en la ficha correspondiente para cambiar los parámetros.

La línea telefónica DSL no encaja en el puerto Internet del router.

El router no es un sustituto del módem. Sigue siendo necesario para utilizar el router. Conecte la línea telefónica al módem DSL y, a continuación, inserte el CD de configuración en el ordenador. Haga clic en Setup (Configuración) y siga las instrucciones que aparecen en- pantalla.

Router de banda ancha Wireless-N

WEB: Si no ha encontrado respuesta a sus dudas,

consulte el sitio web de Linksys, www.linksys.es.

29

Apéndice B

Apéndice B: Especificaciones

Modelo WRT160N Estándares Borrador 802.11n, 802.11g, 802.11b,

802.3, 802.3u Puertos Alimentación, Internet y Ethernet (1-4) Botones Reset (Reinicio), conguración Wi-Fi

protegida Luces Ethernet (1-4), Conguración Wi-Fi

protegida Inalámbrico, Internet, Alimentación

Tipo de cableado CAT 5e Potencia de

radiofrecuencia (EIRP) en dBm 17 dBm

Ganancia de la antena en dBi 1,5 dBi

Cert./compat. UPnP Compatible Funciones de seguridad WEP, WPA, WPA2 Bits de clave de

seguridad 128 bits

Especificaciones

Condiciones ambientales

Dimensiones 202 x 160 x 34 mm (7,95" x 6,3" x 1,34")

Peso 0,29 kg (10,4 onzas) Alimentación 12 V, 0,5 A Certicaciones FCC, CE, IC-03, Wi-Fi Temperatura de

funcionamiento De 0 a 40 °C (de 32 a 104 °F) Temperatura de

almacenamiento De -20 a 60 °C (de -4 a 140 °F) Humedad de

funcionamiento Entre 10 y 85% sin condensación Humedad de

almacenamiento Entre 5 y 90% sin condensación

Router de banda ancha Wireless-N

30

Apéndice C

Información de garantía

Apéndice C: Información de garantía

Garantía limitada

Linksys garantiza que este producto de hardware de Linksys estará exento de defectos de fabricación en los materiales y en condiciones normales de uso durante el periodo de garantía, que comienza en la fecha de adquisición por parte del comprador y usuario final inicial y se extiende durante el periodo que se especifica a continuación:

Dos (2) años para productos nuevos •

Noventa (90) días para productos reparados •

Esta garantía limitada no es transferible y se aplica únicamente al comprador y usuario final inicial. El único recurso y la responsabilidad de Linksys en virtud de la presente garantía limitada será que Linksys, a su elección, (a) repare el producto con piezas nuevas o reparadas, (b) sustituya el producto por otro producto nuevo o reparado de Linksys equivalente que se encuentre disponible de forma razonable, o (c) reembolse el precio de la compra del producto, excepto los posibles descuentos. Todo producto reparado o sustituido estará garantizado durante el tiempo restante del periodo de garantía original o durante treinta (30) días, siendo válida la opción de mayor duración. Todos los productos y piezas que se sustituyan pasarán a ser propiedad de Linksys.

Esta garantía limitada se aplicará además de cualquier otro reglamento o derecho que pudiera establecerse en un contrato de compraventa.

La presente garantía limitada no asegura la disponibilidad continuada de un servicio de terceros que pudiera ser necesario para la utilización o funcionamiento de este producto.

EN LA MEDIDA EN QUE LA LEGISLACIÓN LO PERMITA, TODAS LAS GARANTÍAS IMPLÍCITAS Y CONDICIONES DE COMERCIALIZACIÓN, CALIDAD SATISFACTORIA O IDONEIDAD PARA UN FIN EN PARTICULAR ESTÁN LIMITADAS A LA DURACIÓN DEL PERIODO DE GARANTÍA. SE EXCLUYEN EL RESTO DE CONDICIONES, DECLARACIONES Y GARANTÍAS, EXPLÍCITAS O IMPLÍCITAS, INCLUIDA, ENTRE OTRAS, CUALQUIER GARANTÍA IMPLÍCITA DE NO INFRACCIÓN. En algunas jurisdicciones no está permitido limitar la duración de una garantía implícita, por lo que es posible que la limitación mencionada no se aplique en su caso. Esta garantía limitada confiere al usuario derechos legales específicos. Además, es posible que goce de otros derechos que varían según la jurisdicción.

EN LA MEDIDA EN QUE LA LEGISLACIÓN LO PERMITA, LINKSYS NO SERÁ RESPONSABLE EN NINGÚN CASO POR LAS PÉRDIDAS DE DATOS, INGRESOS O BENEFICIOS, NI POR DAÑOS O PERJUICIOS CUANTIFICABLES, INDIRECTOS O PUNITIVOS, INDEPENDIENTEMENTE DE LA TEORÍA DE LA RESPONSABILIDAD (INCLUIDA LA NEGLIGENCIA), DERIVADOS DE O RELACIONADOS CON EL USO DEL PRODUCTO O LA IMPOSIBILIDAD DE USARLO (INCLUIDO CUALQUIER SOFTWARE), AUNQUE SE HAYA ADVERTIDO A LINKSYS DE LA POSIBILIDAD DE TALES DAÑOS. EN NINGÚN CASO LA RESPONSABILIDAD DE LINKSYS SERÁ SUPERIOR AL IMPORTE QUE EL USUARIO HAYA ABONADO POR EL PRODUCTO. Se aplicarán las limitaciones precedentes incluso en el caso de que algún recurso o garantía estipulados en esta garantía limitada no cumpla con su finalidad esencial. En algunas jurisdicciones no está permitido excluir o limitar los daños derivados o indirectos, por lo que puede que la limitación o exclusión mencionada no se aplique en su caso.

Exclusiones y limitaciones

Esta garantía limitada dejará de tener vigor si: (a) se ha eliminado o dañado el sello de montaje del producto, (b) el producto se ha modificado o alterado, salvo si Linksys ha efectuado tal modificación o reparación; (c) el producto se ha dañado debido a un uso con productos de otros fabricantes, (d) el producto no se ha instalado, utilizado, reparado o mantenido de acuerdo con las instrucciones suministradas por Linksys, (e) se ha sometido al producto a una fuerza física o eléctrica no habituales, un uso incorrecto, negligencias o accidentes, (f ) el número de serie del producto se ha alterado, eliminado o borrado, o (g) el producto se suministra o u obtiene la licencia para una versión beta, para su evaluación o para realización de demostraciones, por tanto, Linksys no cobra una tasa de compra ni de licencia.

TODO EL SOFTWARE QUE LINKSYS PROPORCIONA JUNTO CON EL PRODUCTO, YA SEA CARGADO EN FÁBRICA, EN EL PRODUCTO O EN UNO DE LOS MEDIOS QUE ACOMPAÑAN AL PRODUCTO, SE FACILITA "TAL CUAL", SIN GARANTÍA DE NINGÚN TIPO. Sin perjuicio de lo anterior, Linksys no garantiza que el funcionamiento del producto o del software se realice de forma continuada o que no tenga errores. Del mismo modo y debido al continuo desarrollo de nuevas técnicas de intrusión y ataques a la red, Linksys no garantiza que el producto, el servicio, el software o cualquier tipo de dispositivo, sistema o red en los que se utilice el producto o el software estén exentos de vulnerabilidades a intrusiones o ataques. Es posible que este producto incluya o contenga software u ofertas de servicio de terceros. Esta garantía limitada no se aplicará a dicho software u ofertas de servicio de terceros.

Obtención del servicio de garantía

Si tiene alguna pregunta sobre el producto o si tiene problemas al utilizarlo, visite http://www.linksys.es > Soporte, donde podrá encontrar diversas herramientas de asistencia técnica en línea, así como información para prestarle asistencia con el producto. Si el producto presenta defectos durante el periodo de garantía, póngase en contacto con el servicio de asistencia técnica de Linksys para obtener instrucciones sobre cómo disfrutar del servicio de garantía. Podrá encontrar el número de teléfono de asistencia técnica de Linksys correspondiente a su zona en la guía del usuario y en la dirección www.linksys.es. Cuando llame, tenga preparado el número de serie de su producto y la prueba de compra. PARA PROCESAR RECLAMACIONES DE GARANTÍA, ES NECESARIO CONTAR CON UNA PRUEBA DE COMPRA ORIGINAL FECHADA. Si se le solicita la devolución del producto, se le asignará un número RMA (Autorización de devolución de material). El envío y el embalaje correctos del producto a Linksys corren por su cuenta y riesgo. Al devolver el producto, debe incluir el número RMA y una copia de la prueba de compra original fechada. No se aceptarán los productos recibidos sin número RMA y sin una prueba de compra original fechada. No incluya ningún otro elemento junto con el producto que vaya a devolver a Linksys. Los productos defectuosos que cubra esta garantía limitada se repararán o sustituirán y se devolverán sin ningún tipo de cargo. Aquellos clientes ubicados fuera de los Estados Unidos de América y Canadá serán responsables de todos los gastos de embalaje y envío, gestión, aduanas, IVA y otros impuestos y cargos asociados. Las reparaciones o sustituciones que no cubra esta garantía limitada estarán sujetas a las tarifas vigentes de Linksys.

Router de banda ancha Wireless-N

31

Apéndice C

Asistencia técnica

Esta garantía limitada no es un contrato de servicio ni de asistencia. Podrá encontrar información acerca de las ofertas y políticas de asistencia técnica actuales de Linksys (incluidas las tarifas de los servicios de asistencia técnica) en http://www.linksys.es > Soporte.

General

Esta garantía limitada está sujeta a las leyes de la jurisdicción donde adquirió el producto.

Si se considera que alguna parte de esta garantía limitada es nula o no se puede aplicar, las demás disposiciones seguirán siendo vigentes y efectivas.

Dirija todas sus preguntas a: Linksys, P.O. Box 18558, Irvine, CA 92623 (EE. UU.).

Si desea obtener información adicional, póngase en contacto con nosotros en

www.linksys.es

Escoja su país y, a continuación, la opción de SOPORTE TÉCNICO.

Para devolución de productos:

Escoja su país y, a continuación, la opción de SOPORTE TÉCNICO AL CLIENTE.

Información de garantía

Router de banda ancha Wireless-N

32

Apéndice D

Información sobre normativa

Apéndice D: Información sobre normativa

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Safety Notices

WARNING: Do not use this product near water,

for example, in a wet basement or near a swimming pool.

WARNING: Avoid using this product during an

electrical storm. There may be a remote risk of electric shock from lightning.

•

Reorient or relocate the receiving antenna

Increase the separation between the equipment or • devices

Connect the equipment to an outlet other than the • receiver’s

•

Consult a dealer or an experienced radio/TV technician for assistance

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.

Router de banda ancha Wireless-N

33

Apéndice D

Información sobre normativa

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003 and RSS210.

Operation is subject to the following two conditions:

This device may not cause interference and1. This device must accept any interference, including 2.

interference that may cause undesired operation of the device.

Industry Canada Radiation Exposure Statement

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Avis d’Industrie Canada

Cet appareil numérique de la classe B est conforme aux normes NMB-003 et RSS210 du Canada.

L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes :

il ne doit pas produire de brouillage et 1. il doit accepter tout brouillage radioélectrique reçu, 2.

même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.

Wireless Disclaimer

The maximum performance for wireless is derived from IEEE Standard 802.11 specifications. Actual performance can vary, including lower wireless network capacity, data throughput rate, range and coverage. Performance depends on many factors, conditions and variables, including distance from the access point, volume of network traffic, building materials and construction, operating system used, mix of wireless products used, interference and other adverse conditions.

Avis de non-responsabilité concernant les appareils sans fil

Les performances maximales pour les réseaux sans fil sont tirées des spécifications de la norme IEEE 802.11. Les performances réelles peuvent varier, notamment en fonction de la capacité du réseau sans fil, du débit de la transmission de données, de la portée et de la couverture. Les performances dépendent de facteurs, conditions et variables multiples, en particulier de la distance par rapport au point d’accès, du volume du trafic réseau, des matériaux utilisés dans le bâtiment et du type de construction, du système d’exploitation et de la combinaison de produits sans fil utilisés, des interférences et de toute autre condition défavorable.

Avis d’Industrie Canada concernant l’exposition aux radiofréquences

Ce matériel est conforme aux limites établies par IC en matière d’exposition aux radiofréquences dans un environnement non contrôlé. Ce matériel doit être installé et utilisé à une distance d’au moins 20 cm entre l’antenne et le corps de l’utilisateur.

L’émetteur ne doit pas être placé près d’une autre antenne ou d’un autre émetteur, ou fonctionner avec une autre antenne ou un autre émetteur.

Router de banda ancha Wireless-N

34

Apéndice D

Información sobre normativa

Declaración de conformidad con la directiva de la UE 1999/5/CE (directiva RTTE)

Información sobre la conformidad de los productos inalámbricos de 2,4 GHz y 5 GHz utilizados en la UE y otros países donde se aplique la directiva de la UE 1999/5/CE (directiva RTTE)