Linksys WET610N Owner's Manual

USER GUIDE

Wireless-N Ethernet Bridge

with Dual-Band

Model: WET610N

About This Guide

Icon Descriptions

While reading through the User Guide you may see various icons that call attention to specific items. Below is a description of these icons:

NOTE: This check mark indicates that there is

a note of interest and is something that you should pay special attention to while using the product.

WARNING: This exclamation point indicates

that there is a caution or warning and it is something that could damage your property or product.

About This Guide

WEB: This globe icon indicates a noteworthy

website address or e-mail address.

Online Resources

Website addresses in this document are listed without http:// in front of the address because most current web browsers do not require it. If you use an older web browser, you may have to add http:// in front of the web address.

Resource Website

Linksys www.linksysbycisco.com

Linksys International

Glossary www.linksysbycisco.com/glossary

Network Security

www.linksysbycisco.com/international

www.linksysbycisco.com/security

Linksys, Cisco and the Cisco Logo are registered trademarks or trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Other brands and product names are trademarks or registered trademarks of their respective holders. Copyright © 2009 Cisco Systems, Inc. All rights reserved.

Wireless-N Ethernet Bridge with Dual-Band

Table of Contents

Chapter 1: Product Overview 1

LEDs Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Ports Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Chapter 2: Wireless Security Checklist 2

General Network Security Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Additional Security Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Chapter 3: Advanced Conguration 3

Setup > Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Wireless > Basic Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Wireless > Wireless Network Site Survey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Wireless > WMM® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Wireless > Advanced Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Administration > Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Administration > Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Administration > Upgrade Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Status > Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Status > Wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Status > About . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Appendix A: Troubleshooting 12

Appendix B: Specications 13

Appendix C: Warranty Information 14

Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Exclusions and Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Obtaining Warranty Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Appendix D: Regulatory Information 16

FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Safety Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Industry Canada Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Wireless Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Avis de non-responsabilité concernant les appareils sans l . . . . . . . . . . . . . . . . . .17

Declaration of Conformity with Regard to EU Directive 1999/5/EC (R&TTE Directive) . .18

Wireless Equipment (Wireless-N/G/A/B Products) . . . . . . . . . . . . . . . . . . . . . . . . .19

CE Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

National Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Product Usage Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Technical Documents on www.linksysbycisco.com/international . . . . . . . . . . . . . . .20

User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste

Electric and Electronic Equipment (WEEE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Wireless-N Ethernet Bridge with Dual-Band

Table of Contents

Appendix E: Software Licence Agreement 25

Software in Linksys Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Software Licences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Wireless-N Ethernet Bridge with Dual-Band

iii

Chapter 1

Product Overview

Chapter 1: Product Overview

Thank you for choosing the Linksys by Cisco Wireless-N Ethernet Bridge with Dual-Band. The Bridge can connect any wired, Ethernet device to your wireless network. The Bridge is based on dual-band Wireless-N, so it is compatible with any Wireless-N, -G, -A, or -B router or access point. For first-time installation, run the Setup Wizard on the enclosed CD. To configure advanced settings, use the convenient, browser-based utility.

LEDs Panel

Ethernet (Blue) The Ethernet LED lights up

when there is a wired connection. The LED flashes when the Bridge is actively sending or receiving data over the Ethernet port.

Power (Blue) The Power LED lights up when

the Bridge is powered on.

Ports Panel

Wireless (Blue) The Wireless LED lights up

when there is a wireless connection. The LED flashes when the Bridge is actively sending or receiving data over the wireless network.

Wi-Fi Protected Setup Button If your router

supports Wi-Fi Protected Setup and uses WPA or WPA2 security, then you can use Wi-Fi Protected Setup to automatically connect the Bridge. To use Wi-Fi Protected Setup, run the Setup Wizard, or refer to Wireless > Basic Wireless Settings,

page 4.

Wi-Fi Protected Setup LED (Blue/Amber) The

LED flashes blue for two minutes during Wi-Fi Protected Setup. It lights up blue when wireless security is enabled. If there is an error during the Wi-Fi Protected Setup process, then the LED lights up amber. Make sure the network router supports Wi-Fi Protected Setup. Wait until the LED is off, and then try again.

Ethernet The Ethernet port connects the

Bridge to a computer or other Ethernet network device.

Reset There are two ways to reset the Bridge’s

factory defaults. Either press and hold the Reset button for approximately five seconds, or restore the defaults from Administration > Factory Defaults in the Bridge’s web-based utility.

Power The Power port connects the Bridge to

the included power adapter.

Wireless-N Ethernet Bridge with Dual-Band

Chapter 2

Wireless Security Checklist

Chapter 2: Wireless Security Checklist

Wireless networks are convenient and easy to install, so homes with high-speed Internet access are adopting them at a rapid pace. Because wireless networking operates by sending information over radio waves, it can be more vulnerable to intruders than a traditional wired network. Like signals from your cellular or cordless phones, signals from your wireless network can also be intercepted. Since you cannot physically prevent someone from connecting to your wireless network, you need to take some additional steps to keep your network secure.

1. Change the default wireless network name or SSID

Wireless devices have a default wireless network name or Service Set Identifier (SSID) set by the factory. This is the name of your wireless network, and can be up to 32 characters in length. Linksys wireless products use linksys as the default wireless network name. You should change the wireless network name to something unique to distinguish your wireless network from other wireless networks that may exist around you, but do not use personal information (such as your Social Security number) because this information may be available for anyone to see when browsing for wireless networks.

2. Change the default password

For wireless products such as access points and routers, you will be asked for a password when you want to change their settings. These devices have a default password set by the factory. The Linksys default password is admin. Hackers know these defaults and may try to use them to access your wireless device and change your network settings. To thwart any unauthorized changes, customize the device’s password so it will be hard to guess.

4. Enable encryption

Encryption protects data transmitted over a wireless network. Wi-Fi Protected Access (WPA/WPA2) and Wired Equivalent Privacy (WEP) offer different levels of security for wireless communication.

A network encrypted with WPA/WPA2 is more secure than a network encrypted with WEP, because WPA/WPA2 uses dynamic key encryption. To protect the information as it passes over the airwaves, you should enable the highest level of encryption supported by your network equipment.

WEP is an older encryption standard and may be the only option available on some older devices that do not support WPA.

General Network Security Guidelines

Wireless network security is useless if the underlying network is not secure.

Password protect all computers on the network and • individually password protect sensitive files.

Change passwords on a regular basis. •

Install anti-virus software and personal firewall • software.

Disable file sharing (peer-to-peer). Some applications • may open file sharing without your consent and/or knowledge.

Additional Security Tips

Keep wireless routers, access points, or gateways away • from exterior walls and windows.

Turn wireless routers, access points, or gateways • off when they are not being used (at night, during vacations).

Use strong passphrases that are at least eight characters • in length. Combine letters and numbers to avoid using standard words that can be found in the dictionary.

3. Enable MAC address filtering

Linksys routers give you the ability to enable Media Access Control (MAC) address filtering. The MAC address is a unique series of numbers and letters assigned to every networking device. With MAC address filtering enabled, wireless network access is provided solely for wireless devices with specific MAC addresses. For example, you can specify the MAC address of each computer in your home so that only those computers can access your wireless network.

Wireless-N Ethernet Bridge with Dual-Band

WEB: For more information on wireless security,

visit www.linksysbycisco.com/security

Chapter 3

Advanced Configuration

Chapter 3: Advanced Configuration

After setting up the Bridge with the Setup Wizard (located on the CD-ROM), the Bridge will be ready for use. However, if you want to change its advanced settings, use the Bridge’s web-based utility. This chapter describes each web page of the utility and each page’s key functions. You can access the utility via a web browser on a computer networked with the Bridge.

The web-based utility has these main tabs: Wireless, Network Setup, Administration, and Status. Additional tabs will be available after you click one of the main tabs.

How to Access the Web-Based Utility

Use a web browser to access the web-based utility.

If the Bridge is connected to a network with a DHCP server (usually the network router), then the Bridge will obtain its IP address from the DHCP server. If there is no DHCP server, then the Bridge will use its default static IP address,

169.254.1.250. (If you set a permanent static IP address on the Bridge through the web-based utility, then enter the static IP address instead.)

In the2. Subnet mask field, enter 255.255.0.0.

NOTE: The steps to assign a static IP address to

the Ethernet adapter on your computer vary by operating system. For instructions, please refer to the help documentation of your specific operating system.

After you have assigned your Ethernet adapter with a static IP address, launch your web browser, and enter the Adapter’s IP address (the default setting is 169.254.1.250) in the Address field. Press Enter.

A password request screen appears. (Non-Windows XP users will see a similar screen.) Leave the User name field blank. Enter the password you created during the Setup Wizard. If you did not create a new password, use the default password admin. (You can set a new password from the Administration > Management screen.) Click OK to continue.

Password Screen

NOTE: If you do not know the Bridge’s IP address,

then find its IP address in the DHCP clients table of your router. (Refer to the documentation for your router.)

If you cannot locate the Bridge’s IP address, you can reset the Bridge; press the Reset button on the Bridge for approximately five seconds, using a straightened paper clip. This will reset the Bridge back to the factory default settings. The Bridge will request an IP address from the DHCP server (usually the network router). If no DHCP server is found, then the Bridge will use its default static IP address, 169.254.1.250, until it detects a DHCP server and is assigned a dynamic IP address.

If the Bridge is not associated with a router and is using the factory default settings, connect a computer to the Bridge using an Ethernet connection to access the web-based utility. You will need to configure the Ethernet connection on the computer with a static IP address and subnet mask.

The IP address of your Ethernet adapter should be set to a specific IP address.

NOTE: If the password request screen does not

appear, wait two minutes and try again.

Setup > Basic Setup

The first screen that appears is the Basic Setup screen. Use this screen to change the web-based utility’s language, or to change the Bridge’s wired, Ethernet network settings.

Setup > Basic Setup (Automatic Configuration - DHCP)

In the1. IP address field, enter 169.254.x.y (x should be replaced by a number between 1 and 254, and y should be replaced by a number between 0 and 255).

Wireless-N Ethernet Bridge with Dual-Band

Chapter 3

Setup > Basic Setup (Static IP)

Language

Language This is used to set the language displayed by

the web-based utility. Select the desired language from the drop-down menu.

Network Setup

Advanced Configuration

network. If your network router supports Wi-Fi Protected Setup and uses WPA or WPA2 security, then you can use Wi-Fi Protected Setup to automatically connect the Bridge.

Configuration View To manually configure your wireless

network, select Manual. Refer to Basic Wireless Settings, page 4. To use Wi-Fi Protected Setup, select Wi-Fi Protected Setup. Refer to Wi-Fi Protected Setup, page

Basic Wireless Settings

This section determines if the Bridge’s IP address is obtained automatically from a DHCP server, such as your network router (Automatic Configuration - DHCP), or set manually (Static IP).

Bridge IP If your network has a DHCP server, such as your

network router, assigning IP addresses to your network devices, then keep the default, Automatic Configuration

- DHCP. The Bridge will request an IP address from the DHCP server (usually the network router). If no DHCP server is found, then the Bridge will use its default static IP address, 169.254.1.250, until it detects a DHCP server and is assigned a dynamic IP address.

If you want to set a permanent static IP address for the Bridge, then select Static IP.

If you select Static IP, then complete the following fields:

Static IP Address • Enter a unique IP address that will

be used to access the web-based utility.

Subnet Mask • Enter the subnet mask of your wired

network.

Default Gateway • Enter the IP address of the default

gateway for your network (in most cases, this is your router).

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Wireless > Basic Wireless Settings

Use the Basic Wireless Settings screen to configure the Bridge’s basic wireless and security settings.

There are two ways to configure the Bridge’s settings, manual and Wi-Fi Protected Setup. Wi-Fi Protected Setup is a feature that makes it easy to set up your wireless

Wireless > Basic Wireless Settings (Manual)

Network Name (SSID) The SSID is the network name

shared among all points in a wireless network. The SSID must be identical for all devices in the wireless network. It is case-sensitive and must not exceed 32 characters (use any characters on the keyboard). Make sure this setting matches the setting on your wireless router or access point. For added security, you should change the default SSID (linksys) to a unique name.

Wireless Security

The Bridge supports the following wireless security options: WPA Personal, WPA2 Personal, and WEP. WPA (Wi-Fi Protected Access) and WPA2 are stronger security methods than WEP (Wired Equivalent Privacy). For more information about wireless security, refer to Chapter 2: Wireless Security Checklist, page 2.

Security Mode

Select the security method for your wireless network. If you do not want to use wireless security, keep the default,

Disabled.

NOTE: Remember that each device in your

wireless network MUST use the same security method and passphrase/key, or else the wireless devices will not be able to communicate with each other.

Wireless-N Ethernet Bridge with Dual-Band

Chapter 3

Advanced Configuration

WPA Personal

WPA is a security standard stronger than WEP encryption.

Security Mode > WPA Personal

Encryption WPA supports the TKIP encryption method,

with dynamic encryption keys.

Passphrase Enter the key shared by the Bridge and

your wireless router or access point. It must have 8-63 characters.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

WPA2 Personal

WPA2 is a more advanced, more secure version of WPA.

WEP

WEP is a basic encryption method, which is not as secure as WPA or WPA2.

Security Mode > WEP

Encryption Select a level of WEP encryption, 40/64 bits

(10 hex digits) or 104/128 bits (26 hex digits). The default is 40/64 bits (10 hex digits).

Key 1 Enter the WEP key of your network.

Tx Key Key 1 is the transmit key used by the Bridge.

Authentication The default is Auto, which allows either

Open system or Shared key authentication to be used. Select Open to use open system authentication; the sender and recipient do not use a WEP key for authentication. Select Shared to use shared key authentication; the sender and recipient use a WEP key for authentication.

Security Mode > WPA2 Personal

Encryption WPA2 supports two encryption methods,

TKIP and AES, with dynamic encryption keys. Select the encryption method, AES or TKIP or AES. The default selection is AES.

Passphrase Enter the key shared by the Bridge and

wireless router or access point. It must have 8-63 characters.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Wi-Fi Protected Setup

There are two methods available. Use the method that applies to the router you are using.

Wireless > Basic Wireless Settings (Wi-Fi Protected Setup)

Wireless-N Ethernet Bridge with Dual-Band

Chapter 3

Advanced Configuration

Wi-Fi Protected Setup > Congratulations

Method #1

Use this method if your router has a Wi-Fi Protected Setup button.

Click or press the1. Wi-Fi Protected Setup button on the router.

Within two minutes, click the 2. Wi-Fi Protected Setup button on the Bridge’s Wi-Fi Protected Setup screen.

After the Bridge has been configured, click 3. Close.

The Wi-Fi Protected Setup screen displays the Link Status, Network Name (SSID), and Security method.

Method #2

Use this method if your router requests the PIN number of the Bridge.

On the 1. router’s Wi-Fi Protected Setup screen, enter the PIN number on the Bridge’s Wi-Fi Protected Setup screen. Then click Register or the appropriate button. (It is also listed on the label on the bottom of the Bridge.)

On the 2. Bridge’s Wi-Fi Protected Setup screen, click OK. After the Bridge has been configured, click 3. Close.

The Wi-Fi Protected Setup screen displays the Link Status, Network Name (SSID), and Security method.

Wireless > Wireless Network Site Survey

Wireless Network Site Survey

Number of Wireless Networks The number of wireless

networks detected by the Bridge is displayed.

Select To connect to a wireless network, click Select.

Then click Connect.

Wireless Network Name The network name or SSID of

the wireless network is displayed.

GHz The radio band of the wireless network is displayed.

Signal The percentage of signal strength is displayed.

100% is the strongest signal strength possible; 0% is the weakest possible.

Security

the Wi-Fi Protected Setup icon method used by the wireless network is displayed.

Click Refresh to update the on-screen information.

After you have selected a network, click Connect. A new screen appears. Follow the instructions for the security method of your network.

WPA

the network supports Wi-Fi Protected Setup,

is displayed

. The security

Wireless > Wireless Network Site Survey

Click the Wireless Network Site Survey tab to begin a site survey. The Wireless Network Site Survey screen lists the wireless networks detected by the Bridge.

Wireless-N Ethernet Bridge with Dual-Band

Wireless Network Site Survey > Wireless Security (WPA)

Network Name (SSID) The name of the network you

selected is automatically displayed.

Security Mode WPA Personal is automatically displayed.

Chapter 3

Advanced Configuration

Encryption WPA supports the TKIP encryption method,

with dynamic encryption keys.

Passphrase Enter the key shared by the Bridge and

wireless router or access point. It must have 8-63 characters.

Click Refresh to update the on-screen information.

After you have entered the security settings, click Connect.

WPA2

Wireless Network Site Survey > Wireless Security (WPA2)

Network Name (SSID) The name of the network you

selected is automatically displayed.

Security Mode WEP is automatically displayed.

Encryption Select a level of WEP encryption, 40/64 bits

(10 hex digits) or 104/128 bits (26 hex digits).

Key 1 Enter the WEP key of your network.

Tx Key Key 1 is the transmit key used by the Bridge.

Authentication The default is Auto, which allows either

Click Refresh to update the on-screen information.

After you have entered the security settings, click Connect.

Wireless > WMM®

Configure the Wireless MultiMedia (WMM) settings. WMM prioritizes packets depending on their respective access mode (traffic type): Background, Best Effort, Video, or Voice. These settings should only be adjusted by an expert administrator as incorrect settings can reduce wireless performance.

Security Mode WPA2 Personal is automatically

displayed.

Encryption WPA2 supports two encryption methods,

TKIP and AES, with dynamic encryption keys. Select the encryption method, AES or TKIP or AES.

Passphrase Enter the key shared by the Bridge and

wireless router or access point. It must have 8-63 characters.

Click Refresh to update the on-screen information.

After you have entered the security settings, click Connect.

WEP

Wireless Network Site Survey > Wireless Security (WEP)

Wireless > WMM

NOTE: The settings on the WMM screen are

designed for advanced users only.

WMM

Access Mode

You can assign different settings to the four access modes available. Select the mode you want to configure: Background, Best Effort, Video, or Voice. Follow the instructions for the mode you select.

Network Name (SSID) The name of the network you

selected is automatically displayed.

Wireless-N Ethernet Bridge with Dual-Band

Chapter 3

Advanced Configuration

Background

Use Aggregation This option defines whether or not the

Media Access Control (MAC) layer will set up an Add Block Acknowledgement (ADDBA) session. The default is No. Select Yes to enable this option.

Accept Aggregation This option defines whether or not

the MAC layer will accept an ADDBA request. The default is Yes. Select No to disable this option.

Max. Number of Packets in Aggregation This option

defines the maximum number of packets (sub-frames) in the aggregate. The range is 0 to 7. The default is 7.

Max. Aggregation Size This option defines the maximum

size of the aggregate (in bytes). The range is 0 to 16000. The default is 12000.

Timeout Internal This option defines the timeout period

in which the aggregate should be closed with a “closing condition” before it is closed by the timer. The range is 0 to

100 ms. The default is 3.

Min. Size of Packet in Aggregation This option defines

the minimum size (in bytes) of packets to be accumulated in the aggregate. The range is 0 to 1500. The default is 10.

ADDBA Timeout This option defines the duration

after which the ADDBA setup is terminated, if there are no frame exchanges within this duration by the Block Acknowledgement (ACK) agreement. The range is 0 to

65535 ms. The default is 0, which disables the timeout.

Aggregation Window Size This option defines the

maximum number of packets transmitted without getting ACKs. The range is 0 to 64. The default is 64.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Best Effort

Use Aggregation This option defines whether or not the

Media Access Control (MAC) layer will set up an Add Block Acknowledgement (ADDBA) session. The default is Yes. Select No to disable this option.

Accept Aggregation This option defines whether or not

the MAC layer will accept an ADDBA request. The default is Yes. Select No to disable this option.

Max. Number of Packets in Aggregation This option

defines the maximum number of packets (sub-frames) in the aggregate. The range is 0 to 10. The default is 10.

Max. Aggregation Size This option defines the maximum

size of the aggregate (in bytes). The range is 0 to 20000. The default is 16000.

Timeout Internal This option defines the timeout period

in which the aggregate should be closed with a “closing

condition” before it is closed by the timer. The range is 0 to

100 ms. The default is 3.

Min. Size of Packet in Aggregation This option defines

the minimum size (in bytes) of packets to be accumulated in the aggregate. The range is 0 to 1500. The default is 10.

ADDBA Timeout This option defines the duration

after which the ADDBA setup is terminated, if there are no frame exchanges within this duration by the Block Acknowledgement (ACK) agreement. The range is 0 to

65535 ms. The default is 0, which disables the timeout.

Aggregation Window Size This option defines the

maximum number of packets transmitted without getting ACKs. The range is 0 to 64. The default is 64.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Video

Use Aggregation This option defines whether or not the

Media Access Control (MAC) layer will set up an Add Block Acknowledgement (ADDBA) session. The default is Yes. Select No to disable this option.

Accept Aggregation This option defines whether or not

the MAC layer will accept an ADDBA request. The default is Yes. Select No to disable this option.

Max. Number of Packets in Aggregation This option

defines the maximum number of packets (sub-frames) in the aggregate. The range is 0 to 7. The default is 7.

Max. Aggregation Size This option defines the maximum

size of the aggregate (in bytes). The range is 0 to 16000. The default is 12000.

Timeout Internal This option defines the timeout period

in which the aggregate should be closed with a “closing condition” before it is closed by the timer. The range is 0 to

100 ms. The default is 3.

Min. Size of Packet in Aggregation This option defines

the minimum size (in bytes) of packets to be accumulated in the aggregate. The range is 0 to 1500. The default is 10.

ADDBA Timeout This option defines the duration

after which the ADDBA setup is terminated, if there are no frame exchanges within this duration by the Block Acknowledgement (ACK) agreement. The range is 0 to

65535 ms. The default is 0, which disables the timeout.

Aggregation Window Size This option defines the

maximum number of packets transmitted without getting ACKs. The range is 0 to 64. The default is 64.

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Wireless-N Ethernet Bridge with Dual-Band

Chapter 3

Advanced Configuration

Voice

Use Aggregation This option defines whether or not the

Media Access Control (MAC) layer will set up an Add Block Acknowledgement (ADDBA) session. The default is Yes. Select No to disable this option.

Accept Aggregation This option defines whether or not

the MAC layer will accept an ADDBA request. The default is Yes. Select No to disable this option.

Max. Number of Packets in Aggregation This option

defines the maximum number of packets (sub-frames) in the aggregate. The range is 0 to 2. The default is 2.

Max. Aggregation Size This option defines the maximum

size of the aggregate (in bytes). The range is 0 to 16000. The default is 10000.

Timeout Internal This option defines the timeout period

in which the aggregate should be closed with a “closing condition” before it is closed by the timer. The range is 0 to

100 ms. The default is 10.

Min. Size of Packet in Aggregation This option defines

the minimum size (in bytes) of packets to be accumulated in the aggregate. The range is 0 to 1500. The default is 10.

ADDBA Timeout This option defines the duration

after which the ADDBA setup is terminated, if there are no frame exchanges within this duration by the Block Acknowledgement (ACK) agreement. The range is 0 to

65535 ms. The default is 0, which disables the timeout.

Aggregation Window Size This option defines the

maximum number of packets transmitted without getting ACKs. The range is 0 to 64. The default is 64.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Wireless > Advanced Wireless Settings

Configure the Bridge’s advanced wireless functions. These settings should only be adjusted by an expert administrator as incorrect settings can reduce wireless performance.

NOTE: The settings on the Advanced Wireless

Settings screen are designed for advanced users

only.

Advanced Wireless

Use LDPC Low-Density Parity-Check Code (LDPC) enables

or disables error correction to reduce the probability of data loss in noisy channels. The Rate Adaptation algorithm automatically disabled LDPC coding when working at high PHY rates (higher than 162). To use the LDCP advanced error correction scheme, keep the default, Yes. Otherwise, select No.

ERP Protection Type This option configures protection

of OFDM packets despite the presence of 802.11b stations within the wireless network. By sending RTS/CTS or CTS2Self packets in 802.11b rates, the Bridge informs the wireless network that OFDM packets are going to be transferred and protects the packets in the wireless network. The RTS/CTS and CTS2Self packets create overhead, which may result in lower throughputs.

The RTS/CTS option provides better coverage but lower throughputs when compared to CTS2Self, because the RTS/CTS option includes acknowledgement from the receiving device. To use the RTS/CTS option, keep the default, RTS/CTS. The None option may cause collisions between OFDM and CCK packets. To use the None option, select None. To use the CTS2Self option, select CTS2Self.

11n Protection Type This option configures protection

from non-High Throughput (HT) devices within the wireless network. In case the wireless router (or access point) detects an association of a non-HT legacy device, it will signal all the HT devices to use RTS/CTS or CTS2Self mechanisms before each data transmission. This feature also supports all 802.11n standard protections, including MIMO.

The RTS/CTS option provides better coverage but lower throughputs when compared to CTS2Self, because the RTS/CTS option includes acknowledgement from the receiving device. To use the RTS/CTS option, keep the default, RTS/CTS. The None option may cause collisions between HT and legacy packets. To use the None option, select None. To use the CTS2Self option, select CTS2Self.

Wireless > Advanced Wireless Settings

Wireless-N Ethernet Bridge with Dual-Band

Percentage of maximal transmit power This option

sets the percentage of maximal transmit power relative to the regulatory domain restrictions. For example, if the regulatory domain restriction allows transmissions of up to 20 dB, then setting the percentage at 50% allows maximal transmit power of 10 dB. Select the percentage you want to use: 12%, 25%, 50%, or 100%. The default is 100%.

QoS Classification Type This option sets 802.1D or

802.1Q mapping from the IP DSCP/TOS field to WMM priorities (Background, Best Effects, Video, Voice). Keep

Chapter 3

Advanced Configuration

the default, 802.1D, or select 802.1Q, which is used by some IPTV streams.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Administration > Management

Use this screen to manage specific Bridge functions: access to the web-based utility, backup of the configuration file, and reboot.

System Reboot

Reboot To reboot or restart the Bridge, click Start to

Reboot.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Administration > Factory Defaults

Use this screen to restore the Bridge’s configuration to its factory default settings.

Factory Defaults

Restore All Settings To reset the Bridge’s settings to the

factory defaults, click Restore All Settings. Any settings you have saved will be lost when the default settings are restored.

Administration > Management

Management

Bridge Access

Use a password to protect access to the web-based utility.

Bridge Password Enter a new Password for the Bridge.

Re-enter to confirm Enter the Password again to confirm.

Idle Timeout The login times out after a period of

inactivity that you specify. The range is 60 to 3600 seconds. The default is 600.

Web Access

Access via Wireless If you are using the Bridge in a public

domain where you are giving wireless access to your guests, you can disable wireless access to the Bridge’s web-based utility. You will only be able to access the web-based utility via a wired connection if you disable the setting. Keep the default, Enabled, to allow wireless access to the Bridge’s web-based utility, or select Disabled to block wireless access to the utility.

Backup and Restore

Administration > Factory Defaults

Administration > Upgrade Firmware

Use this screen to upgrade the Bridge’s firmware. Do not upgrade the firmware unless you are experiencing problems with the Bridge or the new firmware has a feature you want to use.

Administration > Upgrade Firmware

Before upgrading the firmware, download the Bridge’s firmware upgrade file from the Linksys website,

www.linksysbycisco.com.

Backup To back up the Bridge’s configuration file, click

Backup Configurations. Then follow the on-screen

instructions.

Restore Click Browse and select the configuration file.

Then click Restore Configurations.

Wireless-N Ethernet Bridge with Dual-Band

Upgrade Firmware

Please select a file to upgrade the firmware Click

Browse and select the firmware upgrade file. Then c Start to Upgrade and follow the on-screen instructions.

lick

Chapter 3

Advanced Configuration

Status > Bridge

The Bridge’s current status information is displayed.

Status > Bridge

Bridge Information

Firmware Version The Bridge’s current firmware is

displayed.

Local Network

Local MAC Address The Bridge’s MAC Address, as seen

on your local, Ethernet network, is displayed.

IP Address The Bridge’s IP Address, as seen on your local,

Ethernet network, is displayed.

Subnet Mask The Subnet Mask configured for your local

network is displayed.

Network Name (SSID) The wireless network name or

SSID is displayed.

BSSID The wireless MAC address of the connected

wireless router (or access point) is displayed.

Radio Band The radio band of your wireless network is

displayed.

Channel Width The channel width, in MHz, used by your

wireless network is displayed.

Wide Channel Depending on the channel settings of

your network router, the Wide Channel is displayed. If you selected Wide - 40MHz Channel for the router’s Radio Band or Channel Width setting, then this will be your primary Wireless-N channel.

Standard Channel The Standard Channel setting is

displayed. If you selected Wide – 40MHz Channel for the router’s Radio Band or Channel Width setting, then the Standard Channel will be a secondary channel for Wireless-N.

Bit Rate The data transmission rate is displayed.

Signal The percentage of signal strength is displayed.

100% is the strongest signal strength possible; 0% is the weakest possible.

Security The security method of your wireless network

is displayed.

Status > About

Status > Wireless

Information about your wireless network is displayed.

Status > Wireless

Wireless

Link Status The status of the connection to your wireless

network is displayed.

MAC Address The Bridge’s MAC Address, as seen on your

local, wireless network, is displayed.

Information about the web-based utility is displayed.

Status > About

Web Server

displayed.

Wireless-N Ethernet Bridge with Dual-Band

Appendix A

Troubleshooting

Appendix A: Troubleshooting

Your computer or other wired, Ethernet device cannot communicate with the wireless router.

Access the web-based utility of the Bridge (refer to 1. Chapter 3: Advanced Configuration, page 3).

On the 2. Basic Wireless Settings screen, make sure the Network Name (SSID) matches the name of your wireless network.

Make sure the security settings (WPA, WPA2, or WEP) 3. match the security settings of your wireless network.

The Bridge’s IP address needs to be changed.

169.254.1.250.

If you want the Bridge to always use a static IP address, then follow these instructions:

Press and hold the Bridge’s Reset button for approximately five seconds; the password will be reset to its factory default, admin. All other Bridge settings will be reset to the factory defaults as well. (To access the web-based utility, enter admin in the Password field.)

After you make changes through the web-based utility, the new settings are not displayed on-screen.

On your web browser, click Refresh. If the new settings are not displayed, then follow these instructions:

Unplug the power adapter from the Bridge. 1. Wait five seconds, and then plug the power adapter 2.

back into the Bridge. On your web browser, click 3. Refresh.

WEB: If your questions are not addressed

here, refer to the Linksys website,

www.linksysbycisco.com

Access the web-based utility of the Bridge (refer to 1. Chapter 3: Advanced Configuration, page 3).

Click the 2. Network Setup tab. From the 3. Network Connection Type drop-down menu,

select Static IP. Complete the 4. Static IP Address, Subnet Mask, and

Default Gateway fields. Click5. Save Settings.

The Bridge-enabled computer or other wired, Ethernet device will not communicate with another wirelessenabled device (such as a computer or printer).

Check the following:

Make sure the wireless-enabled device is on the same • wireless network as the computer or other wired, Ethernet device connected to the Bridge.

Make sure that the same Network Name (SSID) is used • for all devices on the wireless network.

Make sure all devices are on the same IP network, • using compatible IP addresses.

The web-based utility does not accept your password.

Check the following:

The password is case-sensitive. Make sure that you are • using the correct case(s) when entering the password.

If you forget your password, you can reset the Bridge • to its factory defaults.

Wireless-N Ethernet Bridge with Dual-Band

Appendix B

Specifications

Appendix B: Specifications

Model WET610N Standards IEEE 802.3u, 802.11g, 802.11b,

802.11a, draft 802.11n LEDs Power, Ethernet, Wi-Fi Protected

Setup™, Wireless Ports Ethernet, Power Buttons Reset, Wi-Fi Protected Setup™ Cabling Type CAT5e # of Antennas 3 (internal) Antenna Connector

Type N/A Detachable (Yes/No) No Modulations 802.11a: OFDM/BPSK, QPSK,

16-QAM, 64-QAM

802.11b: CCK/QPSK, BPSK

802.11g: OFDM/BPSK, QPSK, 16-QAM, 64-QAM

802.11n: OFDM/BPSK, QPSK, 16-QAM, 64-QAM

RF Pwr (EIRP) in dBm 802.11a: 15 dBm (typical) @ 54Mbps

802.11b: 18 dBm (typical) @ 11 Mbps

802.11g: 16 dBm (typical) @ 54 Mbps

802.11n: 12 dBm (typical) @ 130 Mbps (HT20), 270 Mbps (HT40)

Receive Sensitivity 802.11a: -72 dBm (typical) @ 54 Mbps

802.11b: -85 dBm (typical) @ 11 Mbps

802.11g: -73 dBm (typical) @ 54 Mbps

802.11n: -70 dBm (typical) @ MCS15/2.4 GHz,

-69 dBm (typical) @ MCS15/5.0 GHz

Antenna Gain in dBi 1 Wireless Security WEP, Wi-Fi Protected Access™ 2

(WPA2) Security Key Bits Up to 128-Bit Encryption OS Requirements Windows XP, Vista, or Vista 64-Bit

Edition with Latest Updates (for Setup Wizard only)

Weight 5.61 oz (159 g) Certication FCC, UL/cUL, ICES-003, RSS210,

Wi-Fi (IEEE 802.11a/b/g/draft n), WPA2™, Wi-Fi Protected Setup™

Power 12V, 1A Operating Temp. 32 to 104ºF (0 to 40ºC) Storage Temp. -4 to 140ºF (-20 to 60ºC) Operating Humidity 10 to 85% Noncondensing Storage Humidity 5 to 90% Noncondensing

Specications are subject to change without notice.

Environmental

Dimensions 5.71" x 4.17" x 2.05" (145 x 106 x 52 mm)

Wireless-N Ethernet Bridge with Dual-Band

Appendix C

Warranty Information

Appendix C: Warranty Information

Limited Warranty

Linksys warrants that this Linksys hardware product will be substantially free of defects in materials and workmanship arising under normal use during the Warranty Period, which begins on the date of purchase by the original enduser purchaser and lasts for the period specified below:

Two (2) years for new product •

Ninety (90) days for refurbished product •

This limited warranty is non-transferable and extends only to the original end-user purchaser. Your exclusive remedy and Linksys' entire liability under this limited warranty will be for Linksys, at its option, to (a) repair the product with new or refurbished parts, (b) replace the product with a reasonably available equivalent new or refurbished Linksys product or (c) refund the purchase price of the product less any rebates. Any repaired or replacement products will be warranted for the remainder of the original Warranty Period or thirty (30) days, whichever is longer. All products and/or parts that are replaced become the property of Linksys.

This limited warranty shall apply in addition to any statutory or other rights which you may have under a contract of sale.

Exclusions and Limitations

This limited warranty does not apply if: (a) the product assembly seal has been removed or damaged, (b) the product has been altered or modified, except by Linksys, (c) the product damage was caused by use with non-Linksys products, (d) the product has not been installed, operated, repaired or maintained in accordance with instructions supplied by Linksys, (e) the product has been subjected to abnormal physical or electrical stress, misuse, negligence or accident, (f) the serial number on the Product has been altered, defaced or removed or (g) the product is supplied or licensed for beta, evaluation, testing or demonstration purposes for which Linksys does not charge a purchase price or licence fee.

ALL SOFTWARE PROVIDED BY LINKSYS WITH THE PRODUCT, WHETHER FACTORY LOADED ON THE PRODUCT OR CONTAINED ON MEDIA ACCOMPANYING THE PRODUCT, IS PROVIDED "AS IS" WITHOUT ANY WARRANTY OF ANY KIND. Without limiting the foregoing, Linksys does not warrant that the operation of the product or software will be uninterrupted or error-free. Also, due to the continual development of new techniques for intruding upon and attacking networks, Linksys does not warrant that the product, service, software or any equipment, system or

network on which the product or software is used will be free of vulnerability to intrusion or attack. The product may include or be bundled with third party software or service offerings. This limited warranty shall not apply to such third party software or service offerings. This limited warranty does not guarantee any continued availability of a third party's service for which this product's use or operation may require.

TO THE EXTENT NOT PROHIBITED BY LAW, ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY, SATISFACTORY QUALITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THE WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This limited warranty gives you specific legal rights and you may also have other rights which vary by jurisdiction.

TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT WILL LINKSYS BE LIABLE FOR ANY LOST DATA, TURNOVER OR PROFIT OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT (INCLUDING ANY SOFTWARE), EVEN IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL LINKSYS' LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even if any warranty or remedy provided under this limited warranty fails of its essential purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

Obtaining Warranty Service

If you have a question about your product or experience a problem with it, please go to www.linksys.com/support where you will find a variety of online support tools and information to assist you with your product. If the product proves defective during the Warranty Period, contact Linksys Technical Support for instructions on how to obtain warranty service. The telephone number for Linksys Technical Support in your area can be found in the product User Guide and at www.linksys.com. Have your product serial number and proof of purchase on hand when calling. A DATED PROOF OF ORIGINAL PURCHASE IS REQUIRED TO PROCESS WARRANTY CLAIMS. If you are requested to return your product, you will be given a Return Materials Authorisation (RMA) number. You are responsible for properly packaging and shipping your product to Linksys at your cost and risk. You must include the RMA number

Dual-Band Wireless-N Gigabit Router

Appendix C

and a copy of your dated proof of original purchase when returning your product. Products received without a RMA number and dated proof of original purchase will be rejected. Do not include any other items with the product you are returning to Linksys. Defective product covered by this limited warranty will be repaired or replaced and returned to you without charge. Customers outside of the United States of America and Canada are responsible for all shipping and handling charges, custom duties, VAT and other associated taxes and charges. Repairs or replacements not covered under this limited warranty will be subject to charge at Linksys' then-current rates.

Technical Support

This limited warranty is neither a service nor a support contract. Information about Linksys' current technical support offerings and policies (including any fees for support services) can be found at

www.linksys.com/support

Warranty Information

General

This limited warranty is governed by the laws of the jurisdiction in which the Product was purchased by you.

If any portion of this limited warranty is found to be void or unenforceable, its remaining provisions shall remain in full force and effect.

Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623.

For more information, please contact us

www.linksys.com

Select your country and then select SUPPORT/ TECHNICAL

For product returns:

Select your Country and then select CUSTOMER SUPPORT

Dual-Band Wireless-N Gigabit Router

Appendix D

Regulatory Information

Appendix D: Regulatory Information

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Safety Notices

WARNING: Do not use this product near water,

for example, in a wet basement or near a swimming pool.

WARNING: Avoid using this product during an

electrical storm. There may be a remote risk of electric shock from lightning.

•

Reorient or relocate the receiving antenna

Increase the separation between the equipment or • devices

Connect the equipment to an outlet other than the • receiver’s

•

Consult a dealer or an experienced radio/TV technician for assistance

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.

Wireless-N Ethernet Bridge with Dual-Band

Appendix D

Regulatory Information

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003 and RSS210.

Operation is subject to the following two conditions:

This device may not cause interference and1. This device must accept any interference, including 2.

interference that may cause undesired operation of the device.

Industry Canada Radiation Exposure Statement

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Avis d’Industrie Canada

Cet appareil numérique de la classe B est conforme aux normes NMB-003 et RSS210 du Canada.

L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes :

il ne doit pas produire de brouillage et 1. il doit accepter tout brouillage radioélectrique reçu, 2.

même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.

Wireless Disclaimer

The maximum performance for wireless is derived from IEEE Standard 802.11 specifications. Actual performance can vary, including lower wireless network capacity, data throughput rate, range and coverage. Performance depends on many factors, conditions and variables, including distance from the access point, volume of network traffic, building materials and construction, operating system used, mix of wireless products used, interference and other adverse conditions.

Avis de non-responsabilité concernant les appareils sans fil

Les performances maximales pour les réseaux sans fil sont tirées des spécifications de la norme IEEE 802.11. Les performances réelles peuvent varier, notamment en fonction de la capacité du réseau sans fil, du débit de la transmission de données, de la portée et de la couverture. Les performances dépendent de facteurs, conditions et variables multiples, en particulier de la distance par rapport au point d’accès, du volume du trafic réseau, des matériaux utilisés dans le bâtiment et du type de construction, du système d’exploitation et de la combinaison de produits sans fil utilisés, des interférences et de toute autre condition défavorable.

Avis d’Industrie Canada concernant l’exposition aux radiofréquences

Ce matériel est conforme aux limites établies par IC en matière d’exposition aux radiofréquences dans un environnement non contrôlé. Ce matériel doit être installé et utilisé à une distance d’au moins 20 cm entre l’antenne et le corps de l’utilisateur.

L’émetteur ne doit pas être placé près d’une autre antenne ou d’un autre émetteur, ou fonctionner avec une autre antenne ou un autre émetteur.

Wireless-N Ethernet Bridge with Dual-Band

Appendix D

Regulatory Information

Declaration of Conformity with Regard to EU Directive 1999/5/EC (R&TTE Directive)

Compliance Information for 2,4-GHz and 5-GHz Wireless Products Relevant to the EU and Other Countries Following the EU Directive 1999/5/EC (R&TTE Directive)

Бъ л га р ск и [Bulgarian]

Česky [Czech]:

Dansk [Danish]:

Deutsch [German]:

Eesti [Estonian]:

Това оборудване отговаря на съществените изисквания и приложими клаузи на Директива 1999/5/ЕС.

Toto zařízení je v souladu se základními požadavky a ostatními odpovídajícími ustanoveními Směrnice 1999/5/EC.

Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i Direktiv 1999/5/EF.

Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden Vorgaben der Richtlinie 1999/5/EU.

See seade vastab direktiivi 1999/5/EÜ olulistele nõuetele ja teistele asjakohastele sätetele.

Nederlands [Dutch]:

Malti [Maltese]:

Magyar [Hungarian]:

Norsk [Norwegian]:

Polski [Polish]:

Português [Portuguese]:

Română [Romanian]

Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de Richtlijn 1999/5/EC.

Dan l-apparat huwa konformi mal-ħtiġiet essenzjali u l-provedimenti l-oħra rilevanti tad-Direttiva 1999/5/EC.

Ez a készülék teljesíti az alapvető követelményeket és más 1999/5/EK irányelvben meghatározott vonatkozó rendelkezéseket.

Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-direktiv 1999/5/EF.

Urządzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi warunkami określonymi Dyrektywą UE: 1999/5/EC.

Este equipamento está em conformidade com os requisitos essenciais e outras provisões relevantes da Directiva 1999/5/EC.

Acest echipament este in conformitate cu cerintele esentiale si cu alte prevederi relevante ale Directivei 1999/5/EC.

English:

Español [Spanish]:

Ελληνική [Greek]:

Français [French]:

Íslenska [Icelandic]:

Italiano [Italian]:

Latviski [Latvian]:

Lietuvių [Lithuanian]:

This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directiva 1999/5/CE.

Αυτός ο εξοπλισµός είναι σε συµµόρφωση µε τις ουσιώδεις απαιτήσεις και άλλες σχετικές διατάξεις της Οδηγίας 1999/5/EC.

Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la Directive 1999/5/EC.

Þetta tæki er samkvæmt grunnkröfum og öðrum viðeigandi ákvæðum Tilskipunar 1999/5/EC.

Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva 1999/5/CE.

Šī iekārta atbilst Direktīvas 1999/5/ EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.

Šis įrenginys tenkina 1999/5/EB Direktyvos esminius reikalavimus ir kitas šios direktyvos nuostatas.

Slovensko [Slovenian]:

Slovensky [Slovak]:

Suomi [Finnish]:

Svenska [Swedish]:

Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi pogoji Direktive 1999/5/EC.

Toto zariadenie je v zhode so základnými požiadavkami a inými príslušnými nariadeniami direktív: 1999/5/EC.

Tämä laite täyttää direktiivin 1999/5/EY olennaiset vaatimukset ja on siinä asetettujen muiden laitetta koskevien määräysten mukainen.

Denna utrustning är i överensstämmelse med de väsentliga kraven och andra relevanta bestämmelser i Direktiv 1999/5/EC.

For all products, the Declaration of Conformity (DofC) is available through one or more of these options:

A pdf file is included on the product’s CD. •

A print copy is included with the product. •

A pdf file is available on the product’s webpage. • Visit www.linksysbycisco.com/international and select your country or region. Then select your product.

If you need any other technical documentation, see the “Technical Documents on www.linksysbycisco.com/ international” section, as shown later in this appendix.

Wireless-N Ethernet Bridge with Dual-Band

Appendix D

XXXX

Regulatory Information

Wireless Equipment (Wireless-N/G/A/B Products)

The following standards were applied during the assessment of the product against the requirements of the Directive 1999/5/EC:

Radio: EN 300 328 and/or EN 301 893 as applicable • EMC: EN 301 489-1, EN 301 489-17 • Safety: EN 60950 and either EN 50385 or EN 50371 •

Dynamic Frequency Selection (DFS) and Transmit Power Control (TPC) are required for operation in the 5 GHz band.

DFS: The equipment meets the DFS requirements as defined in ETSI EN 301 893. This feature is required by the regulations to avoid interference with Radio Location Services (radars).

TPC: For operation in the 5 GHz band, the maximum power level is 3 dB or more below the applicable limit. As such, TPC is not required.

CE Marking

For the Linksys Wireless-N, -G, -B, and/or -A products, the following CE mark, notified body number (where applicable), and class 2 identifier are added to the equipment.

In the majority of the EU and other European countries, the 2,4- and 5-GHz bands have been made available for the use of wireless local area networks (LANs). The table labeled “Overview of Regulatory Requirements for Wireless LANs” provides an overview of the regulatory requirements applicable for the 2,4- and 5-GHz bands.

Later in this document you will find an overview of countries in which additional restrictions or requirements or both are applicable.

The requirements for any country may evolve. Linksys recommends that you check with the local authorities for the latest status of their national regulations for both the 2,4- and 5-GHz wireless LANs.

Overview of Regulatory Requirements for Wireless LANs

Frequency

Band (MHz)

2400-2483,5 100 X

5150-5250 200 X

5250-5350

5470-5725

Dynamic Frequency Selection and Transmit Power Control are required † in the frequency ranges of 5250-5350 MHz and 5470-5725 MHz.

The following countries have restrictions and/or requirements in addition to those given in the table labeled “Overview of Regulatory Requirements for Wireless LANs”:

Max Power Level

†

Indoor

(EIRP) (mW)

200 X

1000 X

ONLY

Indoor &

Outdoor

Check the CE label on the product to find out which notified body was involved during the assessment.

National Restrictions

This product may be used in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:

Ce produit peut être utilisé dans tous les pays de l’UE (et dans tous les pays ayant transposés la directive 1999/5/CE) sans aucune limitation, excepté pour les pays mentionnés cidessous:

Questo prodotto è utilizzabile in tutte i paesi EU (ed in tutti gli altri paesi che seguono le direttive EU 1999/5/EC) senza nessuna limitazione, eccetto per i paesi menzionati di seguito:

Das Produkt kann in allen EU Staaten ohne Einschränkungen eingesetzt werden (sowie in anderen Staaten die der EU Direktive 1999/5/CE folgen) mit Außnahme der folgenden aufgeführten Staaten:

Wireless-N Ethernet Bridge with Dual-Band

Croatia

License is required in the band 5150-5350 MHz.

Za pojas od 5150-5350 MHz potrebna je licenca.

Denmark

In Denmark, the band 5150 - 5350 MHz is also allowed for outdoor usage.

I Danmark må frekvensbåndet 5150 - 5350 også anvendes udendørs.

France

For 2,4 GHz, the product is allowed to be used outdoors in the band 2454 - 2483,5 MHz with the condition of eirp limited to 10mW (10 dBm). When operating in the band 2400-2454 MHz, it is restricted for indoor and outdoor use with eirp limited to 100mW (20 dBm). Check http://www.arcep.fr/ for more details.

Pour la bande 2,4 GHz, l’équipement peut être utilisé en extérieur dans la bande 2 454 – 2 483,5 MHz, seulement si la puissance PIRE ne dépasse pas 10 mW (10 dBm). Lors du fonctionnement dans la bande 2 400 – 2 454 MHz, l’utilisation est limitée en intérieur et en extérieur avec une

Appendix D

Regulatory Information

puissance PIRE de à 100 mW (20 dBm) maximum. Consultez

http://www.arcep.fr/ pour de plus amples détails.

Applicable Power Levels in France

Frequency

Band (MHz)

2400-2454 100 (20 dBm) X X

2454-2483,5 100 (20 dBm) X

2454-2483,5 10 (10 dBm) X

Power Level

(EIRP), (mW)

Indoor Outdoor

Italy

This product meets the National Radio Interface and the requirements specified in the National Frequency Allocation Table for Italy. Unless this 2,4-GHz wireless LAN product is operating within the boundaries of the owner’s property, its use requires a “general authorization”. Bands 5150-5350 MHz and 5470-5725 MHz require general authorization if used outdoors. Please check http://www.comunicazioni.it/it/ for more details.

Questo prodotto è conforme alla specifiche di Interfaccia Radio Nazionali e rispetta il Piano Nazionale di ripartizione delle frequenze in Italia. Se non viene installato all’interno del proprio fondo, l’utilizzo di prodotti Wireless LAN a 2,4 GHz richiede una “Autorizzazione Generale”. L’utilizzo all’aperto delle bande di frequenza 5150-5350 MHz e 54705725 MHz è soggetto ad autorizzazione generale. Consultare http://www.comunicazioni.it/it/ per maggiori dettagli.

Latvia

The outdoor usage of the 2,4 GHz band requires an authorization from the Electronic Communications Office. Please check http://www.esd.lv for more details.

2,4 GHz frekveču joslas izmantošanai ārpus telpām nepieciešama atļauja no Elektronisko sakaru direkcijas. Vairāk informācijas: http://www.esd.lv.

Notes:

Although Norway, Switzerland and Liechtenstein are 1. not EU member states, the EU Directive 1999/5/EC has also been implemented in those countries.

The regulatory limits for maximum output power are 2. specified in EIRP. The EIRP level of a device can be calculated by adding the gain of the antenna used (specified in dBi) to the output power available at the connector (specified in dBm).

2,4 GHz Restrictions

This product is designed for use with the standard, integral or dedicated (external) antenna(s) that is/are shipped together with the equipment. However, some applications may require the antenna(s), if removable, to be separated from the product and installed remotely from the device by using extension cables. For these applications, Linksys offers an R-SMA extension cable (AC9SMA) and an R-TNC extension cable (AC9TNC). Both of these cables are 9 meters long and have a cable loss (attenuation) of 5 dB. To compensate for the attenuation, Linksys also offers higher gain antennas, the HGA7S (with R-SMA connector) and HGA7T (with R-TNC connector). These antennas have a gain of 7 dBi and may only be used with either the R-SMA or R-TNC extension cable.

Combinations of extension cables and antennas resulting in a radiated power level exceeding 100 mW EIRP are illegal.

Third-Party Software or Firmware

The use of software or firmware not supported/provided by Linksys may result that the equipment is no longer compliant with the regulatory requirements.

Technical Documents on www.linksysbycisco.com/international

Follow these steps to access technical documents:

Enter 1. http://www.linksysbycisco.com/international in your web browser.

Select the country or region in which you live.2. Click the 3. Products tab. Select the appropriate product category.4. Select the product sub-category, if necessary.5. Select the product.6. Select the type of documentation you want from the 7.

More Information section. The document will open in PDF format if you have Adobe Acrobat installed on your computer.

NOTE: If you have questions regarding

the compliance of this product or you cannot find the information you need, please contact your local sales office or visit

www.linksysbycisco.com/international

Product Usage Restrictions

This product is designed for indoor usage only. Outdoor usage is not recommended, unless otherwise noted.

Wireless-N Ethernet Bridge with Dual-Band

Appendix D

Regulatory Information

User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE)

This document contains important information for users with regards to the proper disposal and recycling of Linksys products. Consumers are required to comply with this notice for all electronic products bearing the following symbol:

English - Environmental Information for Customers in the European Union

European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.

Български (Bulgarian) - Информация относно опазването на околната среда за потребители в Европейския съюз

Европейска директива 2002/96/EC изисква уредите, носещи този символ върху изделието и/или опаковката му, да не се изхвърля т с несортирани битови отпадъци. Символът обозначава, че изделието трябва да се изхвърля отделно от сметосъбирането на обикновените битови отпадъци. Ваша е отговорността този и другите електрически и електронни уреди да се изхвърлят в предварително определени от държавните или общински органи специализирани пунктове за събиране. Правилното изхвърляне и рециклиране ще спомогнат да се предотвратят евентуални вредни за околната среда и здравето на населението последствия. За по-подробна информация относно изхвърлянето на вашите стари уреди се обърнете към местните власти, службите за сметосъбиране или магазина, от който сте закупили уреда.

Čeština (Czech) - Informace o ochraně životního prostředí pro zákazníky v zemích Evropské unie

Evropská směrnice 2002/96/ES zakazuje, aby zařízení označené tímto symbolem na produktu anebo na obalu bylo likvidováno s netříděným komunálním odpadem. Tento symbol udává, že daný produkt musí být likvidován odděleně od běžného komunálního odpadu. Odpovídáte za likvidaci tohoto produktu a dalších elektrických a elektronických zařízení prostřednictvím určených sběrných míst stanovených vládou nebo místními úřady. Správná likvidace a recyklace pomáhá předcházet potenciálním negativním dopadům na životní prostředí a lidské zdraví. Podrobnější informace o likvidaci starého vybavení si laskavě vyžádejte od místních úřadů, podniku zabývajícího se likvidací komunálních odpadů nebo obchodu, kde jste produkt zakoupili.

Dansk (Danish) - Miljøinformation for kunder i EU

EU-direktiv 2002/96/EF kræver, at udstyr der bærer dette symbol

på produktet og/eller emballagen ikke må bortskaffes som usorteret kommunalt affald. Symbolet betyder, at dette produkt skal bortskaffes adskilt fra det almindelige husholdningsaffald. Det er dit ansvar at bortskaffe dette og andet elektrisk og elektronisk udstyr via bestemte indsamlingssteder udpeget af staten eller de lokale myndigheder. Korrekt bortskaffelse og genvinding vil hjælpe med til at undgå mulige skader for miljøet og menneskers sundhed. Kontakt venligst de lokale myndigheder, renovationstjenesten eller den butik, hvor du har købt produktet, angående mere detaljeret information om bortskaffelse af dit gamle udstyr.

Deutsch (German) - Umweltinformation für Kunden innerhalb der Europäischen Union

Die Europäische Richtlinie 2002/96/EC verlangt, dass technische Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem Symbol versehen ist , nicht zusammen mit unsortiertem Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische und elektronische Geräte über die dafür zuständigen und von der Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei, potentielle negative Folgen für Umwelt und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das Produkt erworben haben.

Wireless-N Ethernet Bridge with Dual-Band

Appendix D

Regulatory Information

Eesti (Estonian) - Keskkonnaalane informatsioon Euroopa Liidus asuvatele klientidele

Euroopa Liidu direktiivi 2002/96/EÜ nõuete kohaselt on seadmeid, millel on tootel või pakendil käesolev sümbol , keelatud kõrvaldada koos sorteerimata olmejäätmetega. See sümbol näitab, et toode tuleks kõrvaldada eraldi tavalistest olmejäätmevoogudest. Olete kohustatud kõrvaldama käesoleva ja ka muud elektri- ja elektroonikaseadmed riigi või kohalike ametiasutuste poolt ette nähtud kogumispunktide kaudu. Seadmete korrektne kõrvaldamine ja ringlussevõtt aitab vältida võimalikke negatiivseid tagajärgi keskkonnale ning inimeste tervisele. Vanade seadmete kõrvaldamise kohta täpsema informatsiooni saamiseks võtke palun ühendust kohalike ametiasutustega, jäätmekäitlusfirmaga või kauplusega, kust te toote ostsite.

Español (Spanish) - Información medioambiental para clientes de la Unión Europea

La Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación. Es responsabilidad suya desechar este y cualesquiera otros aparatos eléctricos y electrónicos a través de los puntos de recogida que ponen a su disposición el gobierno y las autoridades locales. Al desechar y reciclar correctamente estos aparatos estará contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y la salud de las personas. Si desea obtener información más detallada sobre la eliminación segura de su aparato usado, consulte a las autoridades locales, al servicio de recogida y eliminación de residuos de su zona o pregunte en la tienda donde adquirió el producto.

Ελληνικά (Greek) - Στοιχεία περιβαλλοντικής προστασίας για πελάτες εντός της Ευρωπαϊκής Ένωσης

Σύμφωνα με την Κοινοτική Οδηγία 2002/96/EC, ο εξοπλισμός που φέρει αυτό το σύμβολο στο προϊόν ή/και τη συσκευασία του δεν πρέπει να απορρίπτεται μαζί με τα μη διαχωρισμένα αστικά απορρίμματα. Το σύμβολο υποδεικνύει ότι αυτό το προϊόν θα πρέπει να απορρίπτεται ξεχωριστά από τα συνήθη οικιακά απορρίμματα. Είστε υπεύθυνος για την απόρριψη του παρόντος και άλλου ηλεκτρικού και ηλεκτρονικού εξοπλισμού μέσω των καθορισμένων εγκαταστάσεων συγκέντρωσης απορριμμάτων, οι οποίες ορίζονται από το κράτος ή τις αρμόδιες τοπικές αρχές. Η σωστή απόρριψη και ανακύκλωση συμβάλλει στην πρόληψη ενδεχόμενων αρνητικών επιπτώσεων στο περιβάλλον και την υγεία. Για περισσότερες πληροφορίες σχετικά με την απόρριψη του παλαιού σας εξοπλισμού, επικοινωνήστε με τις τοπικές αρχές, τις υπηρεσίες αποκομιδής απορριμμάτων ή το κατάστημα από το οποίο αγοράσατε το προϊόν.

Français (French) - Informations environnementales pour les clients de l’Union européenne

La directive européenne 2002/96/CE exige que l’équipement sur lequel est apposé ce symbole sur le produit et/ou son emballage ne soit pas jeté avec les autres ordures ménagères. Ce symbole indique que le produit doit être éliminé dans un circuit distinct de celui pour les déchets des ménages. Il est de votre responsabilité de jeter ce matériel ainsi que tout autre matériel électrique ou électronique par les moyens de collecte indiqués par le gouvernement et les pouvoirs publics des collectivités territoriales. L’élimination et le recyclage en bonne et due forme ont pour but de lutter contre l’impact néfaste potentiel de ce type de produits sur l’environnement et la santé publique. Pour plus d’informations sur le mode d’élimination de votre ancien équipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des déchets, ou l’endroit où vous avez acheté le produit.

Italiano (Italian) - Informazioni relative all’ambiente per i clienti residenti nell’Unione Europea

La direttiva europea 2002/96/EC richiede che le apparecchiature contrassegnate con questo simbolo sul prodotto e/o sull’imballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti domestici. È responsabilità del proprietario smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze potenzialmente negative per l’ambiente e per la salute dell’essere umano. Per ricevere informazioni più dettagliate circa lo smaltimento delle vecchie apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto.

Latviešu valoda (Latvian) - Ekoloģiska informācija klientiem Eiropas Savienības jurisdikcijā

Direktīvā 2002/96/EK ir prasība, ka aprīkojumu, kam pievienota zīme uz paša izstrādājuma vai uz tā iesaiņojuma, nedrīkst izmest nešķirotā veidā kopā ar komunālajiem atkritumiem (tiem, ko rada vietēji iedzīvotāji un uzņēmumi). Šī zīme nozīmē to, ka šī ierīce ir jāizmet atkritumos tā, lai tā nenonāktu kopā ar parastiem mājsaimniecības atkritumiem. Jūsu pienākums ir šo un citas elektriskas un elektroniskas ierīces izmest atkritumos, izmantojot īpašus atkritumu savākšanas veidus un līdzekļus, ko nodrošina valsts un pašvaldību iestādes. Ja izmešana atkritumos un pārstrāde tiek veikta pareizi, tad mazinās iespējamais kaitējums dabai un cilvēku veselībai. Sīkākas ziņas par novecojuša aprīkojuma izmešanu atkritumos jūs varat saņemt vietējā pašvaldībā, atkritumu savākšanas dienestā, kā arī veikalā, kur iegādājāties šo izstrādājumu.

Wireless-N Ethernet Bridge with Dual-Band

Appendix D

Regulatory Information

Lietuvškai (Lithuanian) - Aplinkosaugos informacija, skirta Europos Sąjungos vartotojams

Europos direktyva 2002/96/EC numato, kad įrangos, kuri ir kurios pakuotė yra pažymėta šiuo simboliu (įveskite simbolį), negalima šalinti kartu su nerūšiuotomis komunalinėmis atliekomis. Šis simbolis rodo, kad gaminį reikia šalinti atskirai nuo bendro buitinių atliekų srauto. Jūs privalote užtikrinti, kad ši ir kita elektros ar elektroninė įranga būtų šalinama per tam tikras nacionalinės ar vietinės valdžios nustatytas atliekų rinkimo sistemas. Tinkamai šalinant ir perdirbant atliekas, bus išvengta galimos žalos aplinkai ir žmonių sveikatai. Daugiau informacijos apie jūsų senos įrangos šalinimą gali pateikti vietinės valdžios institucijos, atliekų šalinimo tarnybos arba parduotuvės, kuriose įsigijote tą gaminį.

Malti (Maltese) - Informazzjoni Ambjentali għal Klijenti fl-Unjoni Ewropea

Id-Direttiva Ewropea 2002/96/KE titlob li t-tagħmir li jkun fih issimbolu fuq il-prodott u/jew fuq l-ippakkjar ma jistax jintrema ma’ skart muniċipali li ma ġiex isseparat. Is-simbolu jindika li dan il-prodott għandu jintrema separatament minn ma’ liskart domestiku regolari. Hija responsabbiltà tiegħek li tarmi dan it-tagħmir u kull tagħmir ieħor ta’ l-elettriku u elettroniku permezz ta’ faċilitajiet ta’ ġbir appuntati apposta mill-gvern jew mill-awtoritajiet lokali. Ir-rimi b’mod korrett u r-riċiklaġġ jgħin jipprevjeni konsegwenzi negattivi potenzjali għall-ambjent u għas-saħħa tal-bniedem. Għal aktar informazzjoni dettaljata dwar ir-rimi tat-tagħmir antik tiegħek, jekk jogħġbok ikkuntattja lill-awtoritajiet lokali tiegħek, is-servizzi għar-rimi ta’ l-iskart, jew il-ħanut minn fejn xtrajt il-prodott.

Nederlands (Dutch) - Milieu-informatie voor klanten in de Europese Unie

De Europese Richtlijn 2002/96/EC schrijft voor dat apparatuur die is voorzien van dit symbool op het product of de verpakking, niet mag worden ingezameld met niet-gescheiden huishoudelijk afval. Dit symbool geeft aan dat het product apart moet worden ingezameld. U bent zelf verantwoordelijk voor de vernietiging van deze en andere elektrische en elektronische apparatuur via de daarvoor door de landelijke of plaatselijke overheid aangewezen inzamelingskanalen. De juiste vernietiging en recycling van deze apparatuur voorkomt mogelijke negatieve gevolgen voor het milieu en de gezondheid. Voor meer informatie over het vernietigen van uw oude apparatuur neemt u contact op met de plaatselijke autoriteiten of afvalverwerkingsdienst, of met de winkel waar u het product hebt aangeschaft.

Norsk (Norwegian) - Miljøinformasjon for kunder i EU

EU-direktiv 2002/96/EF krever at utstyr med følgende symbol

avbildet på produktet og/eller pakningen, ikke må kastes sammen med usortert avfall. Symbolet indikerer at dette produktet skal håndteres atskilt fra ordinær avfallsinnsamling for husholdningsavfall. Det er ditt ansvar å kvitte deg med dette produktet og annet elektrisk og elektronisk avfall via egne innsamlingsordninger slik myndighetene eller kommunene bestemmer. Korrekt avfallshåndtering og gjenvinning vil være med på å forhindre mulige negative konsekvenser for miljø og helse. For nærmere informasjon om håndtering av det kasserte utstyret ditt, kan du ta kontakt med kommunen, en innsamlingsstasjon for avfall eller butikken der du kjøpte produktet.

Magyar (Hungarian) - Környezetvédelmi információ az európai uniós vásárlók számára

A 2002/96/EC számú európai uniós irányelv megkívánja, hogy azokat a termékeket, amelyeken, és/vagy amelyek csomagolásán az alábbi címke megjelenik, tilos a többi szelektálatlan lakossági hulladékkal együtt kidobni. A címke azt jelöli, hogy az adott termék kidobásakor a szokványos háztartási hulladékelszállítási rendszerektõl elkülönített eljárást kell alkalmazni. Az Ön felelõssége, hogy ezt, és más elektromos és elektronikus berendezéseit a kormányzati vagy a helyi hatóságok által kijelölt gyűjtõredszereken keresztül számolja fel. A megfelelõ hulladékfeldolgozás segít a környezetre és az emberi egészségre potenciálisan ártalmas negatív hatások megelõzésében. Ha elavult berendezéseinek felszámolásához további részletes információra van szüksége, kérjük, lépjen kapcsolatba a helyi hatóságokkal, a hulladékfeldolgozási szolgálattal, vagy azzal üzlettel, ahol a terméket vásárolta.

Polski (Polish) - Informacja dla klientów w Unii Europejskiej o przepisach dotyczących ochrony środowiska

Dyrektywa Europejska 2002/96/EC wymaga, aby sprzęt oznaczony symbolem znajdującym się na produkcie i/lub jego opakowaniu nie był wyrzucany razem z innymi niesortowanymi odpadami komunalnymi. Symbol ten wskazuje, że produkt nie powinien być usuwany razem ze zwykłymi odpadami z gospodarstw domowych. Na Państwu spoczywa obowiązek wyrzucania tego i innych urządzeń elektrycznych oraz elektronicznych w punktach odbioru wyznaczonych przez władze krajowe lub lokalne. Pozbywanie się sprzętu we właściwy sposób i jego recykling pomogą zapobiec potencjalnie negatywnym konsekwencjom dla środowiska i zdrowia ludzkiego. W celu uzyskania szczegółowych informacji o usuwaniu starego sprzętu, prosimy zwrócić się do lokalnych władz, służb oczyszczania miasta lub sklepu, w którym produkt został nabyty.

Wireless-N Ethernet Bridge with Dual-Band

Appendix D

Regulatory Information

Português (Portuguese) - Informação ambiental para clientes da União Europeia

A Directiva Europeia 2002/96/CE exige que o equipamento que exibe este símbolo no produto e/ou na sua embalagem não seja eliminado junto com os resíduos municipais não separados. O símbolo indica que este produto deve ser eliminado separadamente dos resíduos domésticos regulares. É da sua responsabilidade eliminar este e qualquer outro equipamento eléctrico e electrónico através das instalações de recolha designadas pelas autoridades governamentais ou locais. A eliminação e reciclagem correctas ajudarão a prevenir as consequências negativas para o ambiente e para a saúde humana. Para obter informações mais detalhadas sobre a forma de eliminar o seu equipamento antigo, contacte as autoridades locais, os serviços de eliminação de resíduos ou o estabelecimento comercial onde adquiriu o produto.

Română (Romanian) - Informaţii de mediu pentru clienţii din Uniunea Europeană

Directiva europeană 2002/96/CE impune ca echipamentele care prezintă acest simbol pe produs şi/sau pe ambalajul acestuia să nu fie casate împreună cu gunoiul menajer municipal. Simbolul indică faptul că acest produs trebuie să fie casat separat de gunoiul menajer obişnuit. Este responsabilitatea dvs. să casaţi acest produs şi alte echipamente electrice şi electronice prin intermediul unităţilor de colectare special desemnate de guvern sau de autorităţile locale. Casarea şi reciclarea corecte vor ajuta la prevenirea potenţialelor consecinţe negative asupra sănătăţii mediului şi a oamenilor. Pentru mai multe informaţii detaliate cu privire la casarea acestui echipament vechi, contactaţi autorităţile locale, serviciul de salubrizare sau magazinul de la care aţi achiziţionat produsul.

Slovenčina (Slovak) - Informácie o ochrane životného prostredia pre zákazníkov v Európskej únii

Podľa európskej smernice 2002/96/ES zariadenie s týmto symbolom na produkte a/alebo jeho balení nesmie byť likvidované spolu s netriedeným komunálnym odpadom. Symbol znamená, že produkt by sa mal likvidovať oddelene od bežného odpadu z domácností. Je vašou povinnosťou likvidovať toto i ostatné elektrické a elektronické zariadenia prostredníctvom špecializovaných zberných zariadení určených vládou alebo miestnymi orgánmi. Správna likvidácia a recyklácia pomôže zabrániť prípadným negatívnym dopadom na životné prostredie a zdravie ľudí. Ak máte záujem o podrobnejšie informácie o likvidácii starého zariadenia, obráťte sa, prosím, na miestne orgány, organizácie zaoberajúce sa likvidáciou odpadov alebo obchod, v ktorom ste si produkt zakúpili.

Slovenščina (Slovene) - Okoljske informacije za stranke v Evropski uniji

Evropska direktiva 2002/96/ES prepoveduje odlaganje opreme s tem simbolom – na izdelku in/ali na embalaži z nesortiranimi komunalnimi odpadki. Ta simbol opozarja, da je treba izdelek zavreči ločeno od preostalih gospodinjskih odpadkov. Vaša odgovornost je, da to in preostalo električno in elektronsko opremo oddate na posebna zbirališča, ki jih določijo državne ustanove ali lokalne oblasti. S pravilnim odlaganjem in recikliranjem boste preprečili morebitne škodljive vplive na okolje in zdravje ljudi. Če želite izvedeti več o odlaganju stare opreme, se obrnite na lokalne oblasti, odlagališče odpadkov ali trgovino, kjer ste izdelek kupili.

Suomi (Finnish) - Ympäristöä koskevia tietoja EUalueen asiakkaille

EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämä symboli itse tuotteessa ja/tai sen pakkauksessa, laitteistoa ei saa hävittää lajittelemattoman yhdyskuntajätteen mukana. Symboli merkitsee sitä, että tämä tuote on hävitettävä erillään tavallisesta kotitalousjätteestä. Sinun vastuullasi on hävittää tämä elektroniikkatuote ja muut vastaavat elektroniikkatuotteet viemällä tuote tai tuotteet viranomaisten määräämään keräyspisteeseen. Laitteiston oikea hävittäminen estää mahdolliset kielteiset vaikutukset ympäristöön ja ihmisten terveyteen. Lisätietoja vanhan laitteiston oikeasta hävitystavasta saa paikallisilta viranomaisilta, jätteenhävityspalvelusta tai siitä myymälästä, josta ostit tuotteen.

Svenska (Swedish) - Miljöinformation för kunder i Europeiska unionen

Det europeiska direktivet 2002/96/EC kräver att utrustning med denna symbol på produkten och/eller förpackningen inte får kastas med osorterat kommunalt avfall. Symbolen visar att denna produkt bör kastas efter att den avskiljts från vanligt hushållsavfall. Det faller på ditt ansvar att kasta denna och annan elektrisk och elektronisk utrustning på fastställda insamlingsplatser utsedda av regeringen eller lokala myndigheter. Korrekt kassering och återvinning skyddar mot eventuella negativa konsekvenser för miljön och personhälsa. För mer detaljerad information om kassering av din gamla utrustning kontaktar du dina lokala myndigheter, avfallshanteringen eller butiken där du köpte produkten.

WEB: For additional information, please visit

www.linksysbycisco.com

Wireless-N Ethernet Bridge with Dual-Band

Appendix E

Software Licence Agreement

Appendix E: Software Licence Agreement

Software in Linksys Products

This product from Cisco-Linksys LLC or from one of its affiliates Cisco Systems-Linksys (Asia) Pte Ltd. or CiscoLinksys K.K. ("Linksys") contains software (including firmware) originating from Linksys and its suppliers and may also contain software from the open source community. Any software originating from Linksys and its suppliers is licensed under the Linksys Software Licence Agreement contained at Schedule 1 below. You may also be prompted to review and accept that Linksys Software Licence Agreement upon installation of the software

Any software from the open source community is licensed under the specific license terms applicable to that software made available by Linksys at www.linksys.com/gpl or as provided for in Schedules 2, 3 and 4 below.

Where such specific licence terms entitle you to the source code of such software, that source code is upon request available at cost from Linksys for at least three years from the purchase date of this product and may also be available for download from www.linksys.com/gpl. For detailed licence terms and additional information on open source software in Linksys products please look at the Linksys public web site at: www.linksys.com/gpl/ or Schedules 2, 3 or 4 below as applicable.

BY DOWNLOADING OR INSTALLING THE SOFTWARE, OR USING THE PRODUCT CONTAINING THE SOFTWARE, YOU ARE CONSENTING TO BE BOUND BY THE SOFTWARE LICENCE AGREEMENTS BELOW. IF YOU DO NOT AGREE TO ALL OF THESE TERMS, THEN YOU MAY NOT DOWNLOAD, INSTALL OR USE THE SOFTWARE. YOU MAY RETURN UNUSED SOFTWARE (OR, IF THE SOFTWARE IS SUPPLIED AS PART OF ANOTHER PRODUCT, THE UNUSED PRODUCT) FOR A FULL REFUND UP TO 30 DAYS AFTER ORIGINAL PURCHASE, SUBJECT TO THE RETURN PROCESS AND POLICIES OF THE PARTY FROM WHICH YOU PURCHASED SUCH PRODUCT OR SOFTWARE.

Software Licences

The software Licences applicable to software from Linksys are made available at the Linksys public web site at: www.linksys.com. For your convenience of reference, a copy of the Linksys Software Licence Agreement and the main open source code licences used by Linksys in its products are contained in the Schedules below.

Schedule 1 - Linksys Software Licence Agreement

THIS LICENCE AGREEMENT IS BETWEEN YOU AND CISCO-LINKSYS LLC OR ONE OF ITS AFFILIATES CISCO SYSTEMS-LINKSYS (ASIA) PTE LTD. OR CISCO-LINKSYS K.K. ("LINKSYS") LICENSING THE SOFTWARE INSTEAD OF CISCO-LINKSYS LLC. BY DOWNLOADING OR INSTALLING THE SOFTWARE, OR USING THE PRODUCT CONTAINING THE SOFTWARE, YOU ARE CONSENTING TO BE BOUND BY THIS AGREEMENT. IF YOU DO NOT AGREE TO ALL OF THESE TERMS, THEN YOU MAY NOT DOWNLOAD, INSTALL OR USE THE SOFTWARE. YOU MAY RETURN UNUSED SOFTWARE (OR, IF THE SOFTWARE IS SUPPLIED AS PART OF ANOTHER PRODUCT, THE UNUSED PRODUCT) FOR A FULL REFUND UP TO 30 DAYS AFTER ORIGINAL PURCHASE, SUBJECT TO THE RETURN PROCESS AND POLICIES OF THE PARTY FROM WHICH YOU PURCHASED SUCH PRODUCT OR SOFTWARE.

Licence. Subject to the terms and conditions of this Agreement, Linksys grants the original end user purchaser of the Linksys product containing the Software ("You") a non-exclusive licence to use the Software solely as embedded in or (where authorised in the applicable documentation) for communication with such product. This licence may not be sub-licensed and is not transferable except to a person or entity to which you transfer ownership of the complete Linksys product containing the Software, provided you permanently transfer all rights under this Agreement and do not retain any full or partial copies of the Software and the recipient agrees to the terms of this Agreement.

"Software" includes and this Agreement will apply to (a) the software of Linksys or its suppliers provided in or with the applicable Linksys product, excluding technology from the open source community and (b) any upgrades, updates, bug fixes or modified versions ("Upgrades") or backup copies of the Software supplied to You by Linksys or an authorised reseller, provided you already hold a valid licence to the original software and have paid any applicable fee for the Upgrade.

Protection of Information. The Software and documentation contain trade secrets and/or copyrighted materials of Linksys or its suppliers. You will not copy or modify the Software or decompile, decrypt, reverse engineer or disassemble the Software (except to the extent expressly permitted by law notwithstanding this provision) and You will not disclose or make available such trade secrets or copyrighted material in any form to any third party. Title to and ownership of the Software and documentation and any portion thereof, will remain solely with Linksys or its suppliers.

Collection and Processing of Information. You agree that Linksys and/or its affiliates may, from time to time, collect and process information about your Linksys product and/ or the Software and/or your use of either in order (i) to enable Linksys to offer you Upgrades; (ii) to ensure that

Dual-Band Wireless-N Gigabit Router

Appendix E

Software Licence Agreement

your Linksys product and/or the Software is being used in accordance with the terms of this Agreement; (iii) to provide improvements to the way Linksys delivers technology to you and to other Linksys customers; (iv) to enable Linksys to comply with the terms of any agreements it has with any third parties regarding your Linksys product and/or Software and/or (v) to enable Linksys to comply with all applicable laws and/or regulations or the requirements of any regulatory authority or government agency. Linksys and/ or its affiliates may collect and process this information provided that it does not identify you personally. Your use of your Linksys product and/or the Software constitutes this consent by you to Linksys and/ or its affiliates' collection and use of such information and, for EEA customers, to the transfer of such information to a location outside the EEA.

Software Upgrades etc. If the Software enables you to receive Upgrades, you may elect at any time to receive these Upgrades either automatically or manually. If you elect to receive Upgrades manually or you otherwise elect not to receive or be notified of any Upgrades, you may expose your Linksys product and/or the Software to serious security threats and/or some features within your Linksys product and/or Software may become inaccessible. There may be circumstances where we apply an Upgrade automatically in order to comply with changes in legislation, legal or regulatory requirements or as a result of requirements to comply with the terms of any agreements Linksys has with any third parties regarding your Linksys product and/or the Software. You will always be notified of any Upgrades being delivered to you. The terms of this licence will apply to any such Upgrade unless the Upgrade in question is accompanied by a separate licence, in which event the terms of that licence will apply.

Open Source Software. The GPL or other open source code incorporated into the Software and the open source licence for such source code are available for free download at http://www.linksys.com/gpl. If You would like a copy of the GPL or other open source code in this Software on a CD, Linksys will mail to You a CD with such code for $9.99 plus the cost of shipping, upon request.

Term and Termination. You may terminate this Licence at any time by destroying all copies of the Software and documentation. Your rights under this Licence will terminate immediately without notice from Linksys if You fail to comply with any provision of this Agreement.

Limited Warranty. The warranty terms and period specified in the applicable Linksys Product User Guide shall also apply to the Software.

Disclaimer of Liabilities. IN NO EVENT WILL LINKSYS OR ITS SUPPLIERS BE LIABLE FOR ANY LOST DATA, TURNOVER OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF CAUSE (INCLUDING NEGLIGENCE), ARISING OUT OF

Dual-Band Wireless-N Gigabit Router

OR RELATED TO THE USE OF OR INABILITY TO USE THE SOFTWARE, EVEN IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL LINKSYS' LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even if any warranty or remedy under this Agreement fails of its essential purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to You.

Export. Software, including technical data, may be subject to U.S. export control laws and regulations and/or export or import regulations in other countries. You agree to comply strictly with all such laws and regulations.

U.S. Government Users. The Software and documentation qualify as "commercial items" as defined at 48 C.F.R. 2.101 and 48 C.F.R. 12.212. All Government users acquire the Software and documentation with only those rights herein that apply to non-governmental customers.

General Terms. This Agreement will be governed by and construed in accordance with the laws of the State of California, without reference to conflict of laws principles. The United Nations Convention on Contracts for the International Sale of Goods will not apply. If any portion of this Agreement is found to be void or unenforceable, the remaining provisions will remain in full force and effect. This Agreement constitutes the entire agreement between the parties with respect to the Software and supersedes any conflicting or additional terms contained in any purchase order or elsewhere.

END OF SCHEDULE 1

Schedule 2

If this Linksys product contains open source software licensed under Version 2 of the "GNU General Public Licence" then the licence terms below in this Schedule 2 will apply to that open source software. The licence terms below in this Schedule 2 are from the public web site at

http://www.gnu.org/copyleft/gpl.html

GNU GENERAL PUBLIC LICENCE

This is an unofficial translation of the GNU General Public Licence into [language]. It was not published by the Free Software Foundation and does not legally state the distribution terms for software that uses the GNU GPL— only the original English text of the GNU GPL does that. However, we hope that this translation will help [language] speakers understand the GNU GPL better.

Version 2, June 1991

51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA

+ 256 hidden pages

Linksys WET610N Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Chapter 1: Product Overview

LEDs Panel

Ports Panel

Chapter 2: Wireless Security Checklist

General Network Security Guidelines

Additional Security Tips

Chapter 3: Advanced Configuration

Setup > Basic Setup

Wireless > Basic Wireless Settings

Wireless > Wireless Network Site Survey

Wireless > WMM®

Wireless > Advanced Wireless Settings

Administration > Management

Administration > Factory Defaults

Administration > Upgrade Firmware

Status > Bridge

Status > About

Status > Wireless

Appendix A: Troubleshooting

Appendix B: Specifications

Appendix C: Warranty Information

Limited Warranty

Exclusions and Limitations

Obtaining Warranty Service

Technical Support

Appendix D: Regulatory Information

FCC Statement

Safety Notices

Industry Canada Statement

Wireless Disclaimer

Avis de non-responsabilité concernant les appareils sans fil

Declaration of Conformity with Regard to EU Directive 1999/5/EC (R&TTE Directive)

Wireless Equipment (Wireless-N/G/A/B Products)

CE Marking

National Restrictions

Technical Documents on www.linksysbycisco.com/international

Product Usage Restrictions

User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE)

Appendix E: Software Licence Agreement

Software in Linksys Products

Software Licences