Linksys WAP54GP User Manual

High-Speed Wireless Access for Existing Networks!

The Linksys Wireless-G Access Point lets you connect Wireless-G
(802.11g) or Wireless-B (802.11b) devices to your wired network
so you can add PCs to the network with no cabling hassle.
Power over Ethernet support makes it easy to install – you can
mount the Access Point anywhere, even without ready access
to a power plug. With appropriate Power Over Ethernet support
at the other end, you only need to run one cable to the Access
Point to deliver both data and power.

It's also perfect for use as a bridge, a kind of “cable-less cable”
to connect remote areas together. Maybe Shipping is all the
way across the warehouse from Receiving. Or maybe you
want to set up a home office in your detached garage. With
one Wireless-G Access Point in each end, you're connected at
54Mbps – with no cable to run.

To protect your data and privacy, the Wireless-G Exterior Access
Point supports both Wired Equivalent Privacy (WEP) and the
industrial-strength wireless security of Wi-Fi Protected Access™
(WPA), encoding all your wireless transmissions with powerful
encryption. The MAC Address filter lets you decide exactly who
has access to your wireless network, and advanced logging
and e-mailed intrusion alerts keep you appraised. You can
create multiple SSIDs that connect to individual VLANs to keep
your traffic separated. Configuration is a snap with the web
browser-based configuration utility.

Add high-speed
Wireless-G access to
your wired small
business network

Wireless-G

Wireless

Model No.

Access Point

with Power over Ethernet

WAP54GP

The Linksys Wireless-G Access Point with Power Over Ethernet is
the best way to add wireless access to your existing business
network.

Data rates up to 54Mbps
in Wireless-G (802.11g)
mode, or 11Mbps in
Wireless-B (802.11b)

Multiple SSID and VLAN
support keeps your
traffic separated

Advanced security with
WPA encryption,
logging, and wireless
intrusion protection

Product Data

Wireless-G

Access Point with Power over Ethernet

Features

• 802.11g supports data rates
up to 54Mbps

• Backwards compatible with
existing 802.11b devices

• Supports multiple SSID with
VLAN to create separate,
secured networks

• Supports Power over Ethernet
(PoE)

• Supports SNMP management

Linksys
A Division of Cisco Systems, Inc.
18582 Teller Avenue
Irvine, CA 92612 USA

E-mail: [e-mail]

[e-mail]

Web: http://www.linksys.com

Linksys products are available in more than
50 countries, supported by 12 Linksys Regional
Offices throughout the world. For a complete list of
local Linksys Sales and Technical Support contacts,
visit our Worldwide Web Site at www.linksys.com.

Specifications

Model Number WAP54GP
Standards IEEE802.11g, IEEE802.11b, IEEE802.3, IEEE802.3u,

Ports Ethernet, Antenna, Power
Buttons Reset
Cabling Type UTP CAT 5
LEDs Power, Ethernet, Wireless-G

Setup/Configuration

Web UI Built-in Web UI for Easy Browser-based Configuration (HTTP/HTTPS)

Management

SNMP Version SNMP Version 1, 2c
Event Logging Event Logging
Web F/W Upgrade Firmware Upgradeable through Web Browser
Diags: Flash, etc. Diags: Flash, RAM, LAN, WLAN

Operating Modes

Access Point Access Point Mode
Point-to-Point Point-to-Point (Bridge)
Point-to-Multipoint Point-to-MultiPoint (Bridge)
Repeater Repeater

Wireless

Specs/Modulation Radio and Modulation Type: 802.11b/DSSS, 11g/OFDM
Data Rates Data Rates Supported 11b: 1, 2, 5.5, 11 Mbps,

Channels Operating Channels: 11 North America,

# of Internal Ant. None
# of External Ant. 1 (Omni-Directional)
Antenna Connector Type RSMA
Transmit Power Transmit Power (Adjustable) @ Normal Temp Range:

Receiver Sensitivity Receiver Sensitivity 11g: 54Mbps@ -69dBm, 11b: 11Mbps@ -82dBM

Security

WEP/WPA/WPA2 WEP 64bit/128bit, WPA-TKIP/AES, WPA-PSK, WPA-ENT

802.1x RADIUS Auth. 802.1x - RADIUS (MD5, SHA1, TLS, TTLS, PEAP) Dynamically Varying

Access Control Access Control List (ACL) Capability: MAC-Based
SSID Broadcast SSID Broadcast Enable/Disable
Multiple SSID Supports Multiple SSIDs
Wireless VLAN Map Supports SSID to 802.1q VLAN Mapping with Wireless Client Isolation

IEEE802.3af (Power Over Ethernet), IEEE802.1p (QoS Priority),
IEEE802.1q (VLAN), 802.1x (Security Authentication),

802.11i - Ready (Security WPA2), 802.11e - Ready (Wireless QoS)

11g: 6, 9, 11, 12, 18, 24, 36, 48, 54 Mbps

13 Most of Europe (ETSI and Japan)

11g: Typical - 14dBm, 11b: Typical - 18dBm

Encryption Keys

Environmental

Dimensions 1.26" x 7.83" x 6.89"
W x H x D (32 mm x 199 mm x 175 mm)
Unit Weight 1.01 lbs. (0.46 kg)
Power 12V 1A, IEEE802.3af Compliant PoE
Certifications FCC, CE
Operating Temp. -4ºF to 140ºF (-20ºC to 60ºC)
Storage Temp. -4ºF to 140ºF (-20ºC to 60ºC)
Operating Humidity 5% to 95% Non-Condensing
Storage Humidity 5% to 95% Non-Condensing
Warranty 3-Years Limited

Minimum Requirements

• 802.11b or 802.11g Wireless Adapter with
TCP/IP Protocol Installed per PC

• Network Adapter with Ethernet Network
Cable and TCP/IP Protocol Installed per PC

• Switch/Router with Power Over Ethernet
(PoE) Support or PoE Injector

• Web-Based Configuration Java-Enabled Web
Browser

Package Contents

• Wireless-G Access Point with POE

• User Guide on CD-ROM

•Network Cable

• Power Adapter

• Adapter Stands

• Registration Card

Check the product package and contents for specific features supported. Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc.
and/or its affiliates in the U.S. and certain other countries. Copyright © 2005 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their
respective holders.

WAP54GP-DS-50926A JL

Product Data

Model No.

Model No.

WAP54GP